Garuda - Garba Rujukan Digital

Article Per Year (5 Year)

All

Bulletin of Electrical Engineering and Informatics

EEI
Website

Published by Universitas Ahmad Dahlan

ISSN : - EISSN : - DOI : -

Core Subject : Engineering,

Electrical & Electronics Engineering

Bulletin of Electrical Engineering and Informatics (Buletin Teknik Elektro dan Informatika) ISSN: 2089-3191, e-ISSN: 2302-9285 is open to submission from scholars and experts in the wide areas of electrical, electronics, instrumentation, control, telecommunication and computer engineering from the global world. The journal publishes original papers in the field of electrical, computer and informatics engineering.

Arjuna Subject : -

Articles 2,901 Documents

54 55 56 57 58

Outage probability analysis of EH NOMA system network over Rayleigh fading channel using selection combining at the receiver Phu Tran Tin; Minh Tran; Tran Thanh Trang
Bulletin of Electrical Engineering and Informatics Vol 9, No 1: February 2020
Publisher : Institute of Advanced Engineering and Science

Non-orthogonal multiple access (NOMA) with advantages such as superior spectral efficiency has been considered as a promising multiple access technique for the fifth-generation (5G) mobile networks. In this research, we propose energy harvesting (EH) NOMA system relaying network over Rayleigh fading channel using selection combining at the receiver. Firstly, we investigate the system performance in terms of the closed-form expression of the outage probability (OP). Here we compare the OP of two destination users of the proposed system. Finally, all the results is convinced by the Monte Carlo simulation. From the results, we can confirm that all the analytical and simulation results are the same in connection with the primary system parameters.

Exploiting direct link in EH based two-way DF half-duplex relaying network: Outage probability analysis Phu Tran Tin; Minh Tran; Tran Thanh Trang
Bulletin of Electrical Engineering and Informatics Vol 9, No 1: February 2020
Publisher : Institute of Advanced Engineering and Science

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.11591/eei.v9i1.1652

Relay communication is considered as a popular solution for expanding the coverage, increasing the transmission capacity and reducing the power consumption of the communication networks. In this paper, we proposed and investigated the two-way decode-and-forward (DF) half-duplex (HD) relaying network with the direct link between two sources S1 and S2. Firstly, the system model, energy harvesting (EH) and information transmission (IT) are presented. The closed-form analytical expression of the system outage probability (OP) is analyzed and derived in the next stage. Finally, the correctness of the analytical expressions is verified by Monte Carlo simulation. The research results show that the analytical and simulation are the same in connection with the primary system parameters.

Fabrication of new ceramics nanocomposites for solar energy storage and release Aseel Hadi; Ahmed Hashim Ah-yasari; Dalal Hassan
Bulletin of Electrical Engineering and Informatics Vol 9, No 1: February 2020
Publisher : Institute of Advanced Engineering and Science

The carbides nanostructures have huge applications in renewable energy fields such as the saving of solar energy and release which attributed to the good their properties (thermal, electrical, mechanical, optical and chemical). So, in this paper, the solar energy storage and release of carbides nanoparticles/water for building heating and cooling applications have been investigated with different concentrations of metals carbides nanoparticles (tantalum carbide-silicon carbide). The results showed that the melting and solidification times for thermal energy storage and release decrease with an increase (TaC-SiC) nanoparticles concentrations. From the obtained results, the TaC/SiC nanostructures/ water nano-system are considered as promising materials for solar energy storage and release with high efficiency and high gain (more than 50% compare with the water). Also, the TaC/SiC may be used for heating and cooling fields with good performance and high gain.

Integrated application for automatic schedule-based distribution and monitoring of irrigation by applying the waterfall model process Aulia Naufal Afif; Fiftin Noviyanto; Sunardi Sunardi; Son Ali Akbar; Eko Aribowo
Bulletin of Electrical Engineering and Informatics Vol 9, No 1: February 2020
Publisher : Institute of Advanced Engineering and Science

40% of areas in Indonesia are still using rainwater as a source for irrigation. Type of wetland rainwater always depends on weather that is currently difficult to predict. In addition, the frequency of field cultivation became limited. Irrigation water can come from a dam or a spring in the mountains. Limited water source generates the need to manage water distribution in all areas of rice fields. For every 1 hectare fields, at least 0.5 litres of water per second is needed. The imbalance between the field and the available water discharge can cause conflicts in the Community farmers manage field. The purpose of this research is to assist in the Assembly Of Farmer Water users ("Perkumpulan Petani Pemakai Air" or "P3A") manage the scheduling and controlling irrigation sluice based IoT using mobile applications. The waterfall process model applied in developing mobile applications. Every feature that is created has been tested directly using Unit tests based on the application of the system used. The test is done by observing the system inputs and outputs of the system usability scale (SUS). Tests are also carried out using Post-Study with method of the SUS.

Design and analysis microstrip antenna with reflector to enhancement gain for wireless communication ِAli Khalid Jassim; Raad H. Thaher
Bulletin of Electrical Engineering and Informatics Vol 9, No 2: April 2020
Publisher : Institute of Advanced Engineering and Science

In this paper is presented the good solution to enhancement gain by using physical plane plate reflector with optimum distance by a reflector was used with the antenna and using a sweep parameter for the distance at which the reflector was placed at (, we found the best distance is when selected the bandwidth is 28GHz where . The gain at the bandwidth in 28GHz was improved from (5.48, 6.78, and 7.83) dB to 11.53 dB, while the gain without a reflector is 7.1 dB. The simulation results were obtained using CST which was more consistent with the practical results.

Design of a low-power compact CMOS variable gain amplifier for modern RF receivers M. J. Alam; Mohammad Arif Sobhan Bhuiyan; Md Torikul Islam Badal; Mamun Bin Ibne Reaz; Noorfazila Kamal
Bulletin of Electrical Engineering and Informatics Vol 9, No 1: February 2020
Publisher : Institute of Advanced Engineering and Science

The demand for portability has speeded up the design of low-power electronic communication devices. Variable gain amplifier (VGA) is one of the most vulnerable elements of every modern receiver for the proper baseband processing of the signal. CMOS VGAs are generally suffered from low bandwidth and small gain range. In this research, a two-stage class AB VGA, each stage comprising of a direct transconductance amplifier and a linear transimpedance amplifier, is designed in Silterra 0.13-μm CMOS utilizing Mentor Graphics environment. The post-layout simulation results reveal that the VGA design achieves the widest bandwidth of more than 200 MHz and high gain range from -33 to 32 dB. The VGA dissipates only 2mW from a single 1.2 V DC supply. The core chip area of the VGA is also only 0.026 mm2 which is also the lowest compared to recent researches. Such a VGA will be a very useful module for all modern communication devices.

A design of wideband high-power 3-dB quadrature coupler using defected ground structure for status data transmitting system The Anh Nguyen Dinh; Long Hoang Duc; Duong Bach Gia; Dragos Dancila
Bulletin of Electrical Engineering and Informatics Vol 9, No 1: February 2020
Publisher : Institute of Advanced Engineering and Science

The paper presents a wideband 3-dB quadrature coupler designed for operation at 2 GHz. The presented coupler is based on a broadside-coupled suspended structure in combination with a proposed defected ground structure (DGS) allowing for high power, wide-band and improved harmonic suppression performance. The experimental results show 0.2 dB of insertion loss, return loss of better than 18 dB and isolation of better than 25 dB in the frequency range from 1.74 to 2.67 GHz. The proposed coupler is able to be integrated in the status data transmitting system, which is suitable for vessel monitoring. The fundamental characteristics of the implemented coupler have been measured and verified.

Performance evaluation for outdoor wireless scenarios based on IEEE 802.11b/g in the presence of co-channel interference Roman Alcides Lara-Cueva; Michael Santiago Simba-Herrera
Bulletin of Electrical Engineering and Informatics Vol 9, No 1: February 2020
Publisher : Institute of Advanced Engineering and Science

Voice over Internet Protocol (VoIP) has evolved over the years, being a real-time service. VoIP has been coupled to different technologies, one of them is WiFi, which is one of the most used for wireless local area networks in domestic and commercial environments. In this paper, we evaluate the performance of wireless scenarios by considering VoIP traffic, based on WiFi technology in conformance with IEEE 802.11b/g in interfered outdoor scenarios, by considering an intrusive injection traffic technique, for codecs G711 (1 sample), G711 (2 samples), G723, G729 (2 samples), and G729 (3 samples), related to the main metrics associated to Quality of Service (QoS) parameters. Our results show the best performance was obtained with the codecs G723 and G729 (3 samples), obtaining up to 30 simultaneous voice connections with optimal values of delay, jitter and packet loss according to the recommendations given for VoIP by ITU-T, while the worst performance was obtained with the codec G711 (2 samples), obtaining only 5 simultaneous voice connections, reaching an efficiency loss of around 18% in a co-channel interference scenario.

System architecture to select the charging station by optimizing the travel time considering the destination of electric vehicle drivers in smart cities Ibrahim El-fedany; Driss Kiouach; Rachid Alaoui
Bulletin of Electrical Engineering and Informatics Vol 9, No 1: February 2020
Publisher : Institute of Advanced Engineering and Science

The main limitations of electric vehicles are the limited scope of the battery and their relatively long charging times. This may cause discomfort to drivers of electric vehicles due to a long waiting period at the service of the charging station, during their trips. In this paper, we suggest a model system based on argorithms, allowing the management of charging plans of electric vehicles to travel on the road to their destination in order to minimize the duration of the drivers' journey. The proposed system decision to select the charging station, during advance reservation of electric vehicles, take into account the time of arrival of electric vehicles at charging stations, the expected charging time at charging stations, the local status of the charging stations in real time, and the amount of energy sufficient for the electric vehicle to arrive at the selected charging station. Furthermore, the system periodically updates the electric vehicule reservations to adjust their recharge plans, when they reach their selected earlier station compared to other vehicules requesting new reservations, or they may not arrive as they were forecast, due to traffic jams on the road or certain reluctance on the part of the driver.

Cloud-based people counter Abd Kadir Mahamad; Sharifah Saon; Hamimi Hashim; Mohd Anuaruddin Ahmadon; Shingo Yamaguchi
Bulletin of Electrical Engineering and Informatics Vol 9, No 1: February 2020
Publisher : Institute of Advanced Engineering and Science

Emergence of Industry 4.0 in current economic trend promotes the usage of Internet of Things (IoT) in product development. Counting people on streets or at entrances of places is indeed beneficial for security, tracking and marketing purposes. The usage of cameras or closed-circuit television (CCTV) for surveillance purposes has emerged the need of tools for the digital imagery content analysis to improve the system. The purpose of this project is to design a cloud-based people counter using Raspberry Pi embedded system and send the received data to ThingSpeak, IoT platform. The initial stage of the project is simulation and coding development using OpenCV and Python. For the hardware development, a Pi camera is used to capture the video footage and monitor the people movement. Raspberry Pi acts as the microcontroller for the system and process the video to perform people counting. Experiment have been conducted to measure the performance of the system in the actual environment, people counting on saved video footage and visualized the data on ThingSpeak platform.

Page 56 of 291 | Total Record : 2901

54 55 56 57 58

Filter by Year

2012 2025

Filter By Issues

All Issue Vol 14, No 6: December 2025 Vol 14, No 5: October 2025 Vol 14, No 4: August 2025 Vol 14, No 3: June 2025 Vol 14, No 2: April 2025 Vol 14, No 1: February 2025 Vol 13, No 6: December 2024 Vol 13, No 5: October 2024 Vol 13, No 4: August 2024 Vol 13, No 3: June 2024 Vol 13, No 2: April 2024 Vol 13, No 1: February 2024 Vol 12, No 6: December 2023 Vol 12, No 5: October 2023 Vol 12, No 4: August 2023 Vol 12, No 3: June 2023 Vol 12, No 2: April 2023 Vol 12, No 1: February 2023 Vol 11, No 6: December 2022 Vol 11, No 5: October 2022 Vol 11, No 4: August 2022 Vol 11, No 3: June 2022 Vol 11, No 2: April 2022 Vol 11, No 1: February 2022 Vol 10, No 6: December 2021 Vol 10, No 5: October 2021 Vol 10, No 4: August 2021 Vol 10, No 3: June 2021 Vol 10, No 2: April 2021 Vol 10, No 1: February 2021 Vol 9, No 6: December 2020 Vol 9, No 5: October 2020 Vol 9, No 4: August 2020 Vol 9, No 3: June 2020 Vol 9, No 2: April 2020 Vol 9, No 1: February 2020 Vol 8, No 4: December 2019 Vol 8, No 3: September 2019 Vol 8, No 2: June 2019 Vol 8, No 1: March 2019 Vol 7, No 4: December 2018 Vol 7, No 3: September 2018 Vol 7, No 2: June 2018 Vol 7, No 1: March 2018 Vol 6, No 4: December 2017 Vol 6, No 3: September 2017 Vol 6, No 2: June 2017 Vol 6, No 1: March 2017 Vol 5, No 4: December 2016 Vol 5, No 3: September 2016 Vol 5, No 2: June 2016 Vol 5, No 1: March 2016 Vol 4, No 4: December 2015 Vol 4, No 3: September 2015 Vol 4, No 2: June 2015 Vol 4, No 1: March 2015 Vol 3, No 4: December 2014 Vol 3, No 3: September 2014 Vol 3, No 2: June 2014 Vol 3, No 1: March 2014 Vol 2, No 4: December 2013 Vol 2, No 3: September 2013 Vol 2, No 2: June 2013 Vol 2, No 1: March 2013 Vol 1, No 4: December 2012 Vol 1, No 3: September 2012 Vol 1, No 2: June 2012 Vol 1, No 1: March 2012 List of Accepted Papers (with minor revisions) More Issue

Home Page

OAI Link

Editorial Team

Contact

Reviewer

Google Scholar

Contact Name
-

Contact Email
-

Phone
-

Journal Mail Official
-

Editorial Address
-

Location
Kota yogyakarta,

Daerah istimewa yogyakarta

INDONESIA

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Home Page

OAI Link

Editorial Team

Contact

Reviewer

Google Scholar

Contact Name -

Contact Email -

Phone -

Journal Mail Official -

Editorial Address -

Location Kota yogyakarta, Daerah istimewa yogyakarta INDONESIA

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Contact Name
-

Contact Email
-

Phone
-

Journal Mail Official
-

Editorial Address
-

Location
Kota yogyakarta,

Daerah istimewa yogyakarta

INDONESIA