Claim Missing Document
Check
Articles

Found 14 Documents
Search

STUDI PERILAKU PADA SAMBUNGAN RECTANGULAR CONCRETE FILLED TUBES (RCFT) DENGAN METODE FINITE ELEMENT Cintantya Budi Casita; Budi Suswanto
Journal of Civil Engineering Vol 32, No 1 (2017)
Publisher : Institut Teknologi Sepuluh Nopember

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (393.039 KB) | DOI: 10.12962/j20861206.v32i1.4505

Abstract

This research presents the result of two rectangular filled tube column-to-beam connections under cyclic loading using finite element analysis. Connections of all two models were using weld connection and shear tab attached to beam webs. In this study, 2 models were made: RR-1 and RB-2, which are RCFT connection with RBS and RCFT connection without RBS. This study is conducted to learn, the advantages of RCFT connection with RBS against RCFT connection without RBS. The analysis results observed that cyclic performance of the RBS moment connection was much superior to the connection without RBS. The highest regions of stress occur in vicinity of beam bottom flange near column face for connection without RBS. For connection with RBS, the highest regions of stress occur in reduced beam section of the beam
STUDI PERILAKU LINK PENDEK, LINK MENENGAH DAN LINK PANJANG PADA STRUKTUR BAJA SISTEM EBF Jusuf Wilson Meynerd Rafael; Budi Suswanto
Journal of Civil Engineering Vol 32, No 1 (2017)
Publisher : Institut Teknologi Sepuluh Nopember

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (633.288 KB) | DOI: 10.12962/j20861206.v32i1.4506

Abstract

The paper disccuses an analysis study on the design of Eccentrically Braced Frame (EBF) i.e. short link, intermediate link and long link) with K-Braces-type Split 1 floor. The analysis is performed by using ABAQUS with static monotonic loading in a single structure (frame). Each element of the frame is modeled as sholid 3D with connections to every element in the form of tie constraints and given fixed on each base of the column as a boundary condition. All three models of the frame has been analyzed in accordance with the AISC 2010 provisions and then compared the behavior of each of these models. The results indicate that the short link model considered in this study have on a higher over strength value and used as a proposed model when compared to intermediate link and long link model. It is stated by the failure mechanism as well, the failure is well-occurred in the short link condition than the other models
ANALISIS ALIRAN INFORMASI KOMUNIKASI INTERNAL DALAM IMPLEMENTASI MOBILE WORKING PADA PERUSAHAAN MEDIA PENYEDIA KONTEN INTERNAL MAGAZINE (Studi Kasus di PT Tanair Media Seruni) Budi Suswanto
MediaKom : Jurnal Ilmiah Komunikasi Vol 6, No 2 (2016): Mediakom Jurnal Ilmiah Ilmu Komunikasi
Publisher : Universitas Mercu Buana

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

Changes in internal communications technology company influence the development of communication technology. Internal communication through physical meetings members initially turned into mobile technology. The study aims to analyze the flow of internal communication of information on the implementation of mobile working in PT Tanair Media chrysanthemum, coordination and management tasks with a mobile system working. Data were collected through direct observation in the field, in-depth interviews to five key informants and documentation. The study was conducted by using a qualitative approach with constructivism. The theory is Communicative Constitution of Organizations and Weick. Discussion of the results obtained conclusions: (1) Changes in the system of internal communication technology-based organizations keep up with technology, (2) The use of social media technologies and application-oriented Media Vista duties and functions, (3) Coordination management tasks with mobile working systems tailored to the plan, organize, action and control.
Analisis Numerik Vertical Shear Link (VSL) secara Sub-Assemblage menggunakan Program Bantu ABAQUS Ifarrel Rachmanda Hariyanto; Budi Suswanto; Ahmad Basshofi Habieb
Jurnal Aplikasi Teknik Sipil Vol 20, No 3 (2022)
Publisher : Departemen Teknik Infrastruktur Sipil Institut Teknologi Sepuluh Nopember Surabaya

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1756.777 KB) | DOI: 10.12962/j2579-891X.v20i3.13298

Abstract

Indonesia merupakan negara dengan tingkat kegempaan yang cukup tinggi, sehingga gempa seringkali menimbulkan korban jiwa. Untuk mengurangi korban jiwa akibat gempa, perlu didesain gedung yang dapat memenuhi kebutuhan performa struktur seperti kekuatan dan daktilitas. Eccentrically Braced Frames (EBF) adalah salah satu struktur baja daktail yang cocok digunakan pada daerah rawan gempa. Link pada EBF yang umum digunakan adalah link horizontal yang memiliki beberapa kelemahan seperti dapat merusak beban berat atau peralatan yang sangat sensitif terutama pada gedung pembangkit listrik sehingga dilakukan penelitian terkait link vertikal. Penelitian ini membahas tentang analisis numerik penggunaan Vertical Shear Link (VSL) dengan menggunakan program bantu ABAQUS yang kemudian dilakukan perbandingan hasil analisis dengan penelitian eksperimental oleh Zahrai dkk. (2015). Analisis numerik dilakukan untuk memverifikasi hasil eksperimen meliputi von mises stress, moda deformasi, dan kurva histerisis. Hasil numerik menunjukkan bahwa badan link mencapai tegangan runtuh pada akhir pengujian. Kapasitas beban puncak yang dihasilkan oleh analisis numerik adalah 22,723 ton dengan selisih antara eksperimental sebesar 1,05%.
Studi Perilaku Floordeck Komposit Baja Akibat Beban Lentur dengan Metode Elemen Hingga Axel Ricardo Santoso; Budi Suswanto; Ahmad Basshofi Habieb
Jurnal Aplikasi Teknik Sipil Vol 20, No 3 (2022)
Publisher : Departemen Teknik Infrastruktur Sipil Institut Teknologi Sepuluh Nopember Surabaya

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1655.979 KB) | DOI: 10.12962/j2579-891X.v20i3.13330

Abstract

Penelitian ini adalah analisis dengan metode elemen hingga terkait floordeck, untuk mendapatkan momen, kuat geser, dan kegagalan sturktur pada pelat lantai. Hasil pemodelan validasi dibandingkan dengan hasil modifikasi dengan beban maksimum dan defleksi sebesar 115,54 kN dan 26 mm pada model validasi 1, sedangkan model modifikasi 1 sebesar 77,76 kN dan 28 mm. Pengaruh besarnya adalah shear connector, terjadi kenaikan beban maksimum sebesar 33% serta kenaikan defleksi sebesar 7%. Model modifikasi dengan 4 variasi panjang, pada model M1 mendapatkan beban maksimum 77,76 kN pada defleksi sebesar 28,82 mm, sedangkan defleksi ujung beban sebesar 65,66 kN. Pada permodelan M2 dengan bentang 2,5m mendapatkan beban maksimum 53,54 kN pada defleksi sebesar 30 mm.  Maka dengan model seterusnya akan menggalami tren yang menurun karna panjang suatu model. Begitu juga dengan Momen maksimum, gaya geser, dan kegagalan sturktur pelat dimana semakin panjang bentang yang dimodelkan maka akan semakin kecil nilai yang didapat.
Pengaruh Aplikasi Fibre Reinforced Polymer (FRP) terhadap Perkuatan Kolom Concrete Filled Steel Tube (CFT) menggunakan Metode Elemen Hingga Ida Ayu Putu Eka Chandra Saraswati; Budi Suswanto; Basshofi Habieb
Jurnal Aplikasi Teknik Sipil Vol 20, No 3 (2022)
Publisher : Departemen Teknik Infrastruktur Sipil Institut Teknologi Sepuluh Nopember Surabaya

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1850.17 KB) | DOI: 10.12962/j2579-891X.v20i3.13136

Abstract

Kolom tabung baja terisi beton (CFT) banyak diaplikasikan pada sistem struktur bentang panjang karena beberapa keunggulannya seperti kekuatan, daktilitas, dan kekakuan yang lebih tinggi dari kolom baja konvensional. Namun, akibat pembebanan berulang, tekuk lokal terbentuk sehingga mengurangi efisiensi pengekangan beton inti oleh tabung baja. Penelitian ini membahas perkuatan kolom CFT dengan pemasangan 3 lapis FRP tipe karbon (CFRP) pada daerah yang berpotensi terjadi sendi plastis. Kolom dimodelkan terhadap beban lateral siklik menggunakan program ABAQUS. Parameter analisis berupa tebal baja kolom CFT dan lapisan CFRP. Hasil analisa menunjukkan CFRP signifikan meningkatkan kapasitas tahanan, menambah initial stiffness, disipasi energi, mengurangi tingkat kehancuran beton inti dan menghambat tekuk tabung baja pada kolom CFT. Perilaku material CFRP yang getas masih mampu bekerja dengan baik pada kolom CFT dengan menunjukkan tren degradasi kekakuan yang tidak tajam. Namun, ketika diaplikasikan pada kolom CFT dengan tebal baja lebih dari 3 mm, kapasitas tahanan dan kekakuan kolom CFT yang dilapisi CFRP menjadi berkurang.
INTENSITAS KOMUNIKASI INTERPERSONAL AYAH DAN ANAK LAKI-LAKI USIA 7 - 8 TAHUN DALAM KEBERHASILAN PEMBELAJARAN JARAK JAUH (STUDI KASUS DI RW 08 KELURAHAN SRIAMUR, TAMBUN UTARA, BEKASI) BUDI SUSWANTO; TRISNAWATI KUSUMAWARDHANI
Interpretasi: Communication & Public Relations Vol 2, No 2 (2022): Interpretasi: Communication & Public Relation
Publisher : Institut Bisnis Muhammadiyah Bekasi

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (231.495 KB) | DOI: 10.53990/ijpik.v2i2.187

Abstract

The task of a father at home is not only responsible for meeting the material needs of the family, but also for the process of growth and education of children. Especially boys. One of them is by providing assistance during the Pelajaran Jarak Jauh (PJJ) process. This study aims to determine how interpersonal communication between fathers and sons aged 7-8 years in the success of the PJJ process in RW 08, Sriamur Village, Tambun Utara District, Bekasi. Data were collected through direct observation in the field, in-depth interviews with six key informants, and documentation. The research was conducted using a qualitative approach with a constructivist paradigm. The theory used is Interpersonal Communication or Interpersonal Communication proposed by R. Wayne Pace. Based on the conclusions from the results of the research conducted, a father plays a very important role in the success of the PJJ process for his son. For boys, fathers are role models in their lives. Because in terms of using technology in PJJ, dad is more responsive. In addition, the way a father communicates in a soft and motivating language, makes it easier for children to understand lessons.
Validasi Portal Vertical Eccentrically Braced Frames (V-EBF) Menggunakan Profil WF Shear Link dengan Metode Elemen Hingga Arina Desye Hariyanti; Budi Suswanto
Jurnal Aplikasi Teknik Sipil Vol 21, No 3 (2023)
Publisher : Departemen Teknik Infrastruktur Sipil Institut Teknologi Sepuluh Nopember Surabaya

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.12962/j2579-891X.v21i3.18438

Abstract

Sistem Eccentrically Braced Frame (EBF) merupakan kombinasi dari kedua sistem yang lain dimana menggabungkan kelebihan dari Moment Resisting Frame (MRF) dan Concentrically Braced Frame (CBF) serta mengurangi kelemahannya. Karakteristik EBF antara lain: memiliki kekakuan elastis yang tinggi, memiliki respons in-elastik yang stabil di pembebanan siklik lateral, memiliki kemampuan daktilitas dan disipasi energi yang tinggi. Apabila ada beban gempa maka balok link akan in-elastic, sehingga dipilih Vertical Shear Link (VSL), pertimbangannya link ini mudah diganti apabila ada kerusakan saat gempa besar tanpa mengubah bagian dari balok. Dari analisa menggunakan metode elemen hingga dengan program Abaqus, kemudian membandingkan kurva histeristis dan kapasitas disipasi energinya, kemudian didapatkan hasil validasi elemen link yang mengalami pelelehan dan mencapai kondisi plastis terlebih dahulu sedangkan elemen lain seperti balok, kolom dan bracing masih dalam kondisi elastis sehingga memenuhi persyaratan untuk Eccentrically Braced Frame (EBF). Selisih antara hasil pemodelan umerik dengan hasil esksperimental di bawah 5% sehingga cukup valid bisa digunakan sebagai dasar untuk memodelkan struktur Eccentrically Braced Frame (EBF).
Analisis Perilaku Konfigurasi Pelat Pengaku pada Sistem Struktur Steel Plate Shear Wall (SPSW) yang Tersambung pada Sisi Horizontal Boundary Element (HBE) Haykal Wildan Tamimi El Jauhari; Budi Suswanto
Jurnal Aplikasi Teknik Sipil Vol 21, No 3 (2023)
Publisher : Departemen Teknik Infrastruktur Sipil Institut Teknologi Sepuluh Nopember Surabaya

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.12962/j2579-891X.v21i3.17221

Abstract

Sistem Steel Plate Shear Wall (SPSW) adalah sebuah sistem struktur yang mampu menunjukkan deformasi kekakuan awal yang tinggi, berperilaku daktail, dan mendisipasi energi yang besar, sehingga cocok menjadi sistem penahan gempa yang besar. Pelepasan pelat pengisi pada kolom dapat menguntungkan karena kemungkinan kegagalan awal yang terjadi pada kolom dapat diminimalisir. Untuk meningkatkan gaya geser dan disipasi energi maka perlu adanya penambahan pelat pengaku pada elemen shearwall. Pada penelitian ini dilakukan pengujian terhadap beberapa model konfigurasi pelat pengaku yaitu diantaranya; berbentuk cross dan strip model. Hasil pengujian yaitu berupa; diagram kurva histeresis, pola deformasi pelat, kapasitas disipasi energi dan kapasitas gaya geser. Penelitian ini menggunakan metode elemen hingga dengan program bantu ABAQUS. Hasil penelitian menunjukkan bahwa penambahan pelat pengaku pada daerah TFA (tension field action) memiliki pengaruh yang sangat signifikan dalam meningkatkan kekakuan awal yang baik, meningkatkan kapasitas gaya geser dan menghasilkan disipasi energi yang sangat baik.
Implementasi Kode Etik Insinyur dan Profesionalisme terhadap Signifikansi Metode Pelaksanaan dan Manajemen Proyek pada Proyek Konstruksi Rehabilitasi Laboratorium dan Lapangan SMPN 2 Kota Mojokerto Rahmanita Nuzula; Ridho Bayu Aji; M. Sigit Darmawan; Budi Suswanto; RPX Rooswan Happmono
Inisiatif: Jurnal Ekonomi, Akuntansi dan Manajemen Vol. 4 No. 2 (2025): April : Inisiatif : Jurnal Ekonomi, Akuntansi dan Manajemen
Publisher : Universitas 45 Surabaya

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30640/inisiatif.v4i2.3809

Abstract

The implementation method and project management are important points in the running of this rehabilitation project. In accordance with the planning document, it is expected that the significance of planning and implementation does not have a much different percentage. The implementation method is the center of the formation of the plan until it becomes a new building after rehabilitation, as well as project management that focuses on time and quality control is also part of the implementation of the project. The results of the observation of engineering practices found that the percentage of building rehabilitation implementation methods that occurred in the field was 97.43%, while the percentage of field rehabilitation was 97.33%. So the total percentage of the overall work carried out against the plan is 97.38%. The results for time and quality management were obtained that from the 19th to the 20th week there was a delay in the work because in that week there was a material delay, this is known from the analysis of the daily report on the project. In completing the work according to the specified time is carried out with quality according to specifications, re-scheduling is carried out on certain work. From these results, it can be said that they are responsible for their profession which reflects the code of ethics of engineers as well as the ability to complete work well which reflects professionalism.