Claim Missing Document
Check
Articles

Found 5 Documents
Search
Journal : JURNAL INTEGRASI

Komputasi Tingkat Kesehatan Instalasi Listrik pada Gedung Fauzun Atabiq; Yohanes Suyanto
JURNAL INTEGRASI Vol 9 No 1 (2017): Jurnal Integrasi - April 2017
Publisher : Politeknik Negeri Batam

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30871/ji.v9i1.262

Abstract

Kesehatan instalasi listrik gedung adalah kondisi mengenai baik buruknya integritas instalasi listrik sistem instalasi listrik pada suatu gedung. Tujuan dari penelitian ini adalah mengembangkan sebuah teknik evaluasi kesehatan instalasi listrik untuk menentukan tingkat kesehatan instalasi listrik pada sebuah gedung/bangunan. Sebuah sistem komputasi kesehatan instalasi listrik telah dimodelkan untuk mengevaluasi tingkat kesehatan instalasi kelistrikan pada sebuah gedung berdasarkan parameter-parameter instalasi. Dengan melakukan ekivalen analisis terhadap beberapa parameter instalasi seperti; usia instalasi, pembebanan circuit breaker, pembebanan pada kabel, ketidakimbangan beban instalasi dan temperatur pada panel di setiap panel instalasi listrik yang ada pada gedung, kondisi kesehatan instalasi listrik sebuah gedung dapat ditentukan. Dari implementasi yang dilakukan pada instalasi listrik Gedung S2/S3 FMIPA UGM pada bulan Maret - April 2016, hasil penelitian memperlihatkan bahwa tingkat kesehatan instalasi listrik Gedung S2/S3 FMIPA UGM secara keseluruhan adalah di atas 7.0, atau secara garis besar menunjukkan bahwa kondisi kesehatan instalasi listrik pada gedung tersebut adalah baik.
Evaluasi Efisiensi Motor Induksi Satu Fase Berdaya Kurang dari 1 HP yang Dilakukan Perbaikan dengan Cara Rewinding Fauzun Atabiq; Arif Febriansyah Juwito; Afrizal Afrizal; Ilham Kurnia
JURNAL INTEGRASI Vol 10 No 1 (2018): Jurnal Integrasi - April 2018
Publisher : Politeknik Negeri Batam

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30871/ji.v10i1.661

Abstract

Perbaikan sebuah motor listrik yang berkualitas selain dapat mengurangi biaya sebuah industri juga dapat menjaga proses operasi dan produksi terjamin. Meskipun demikian dengan kenaikan tarif dasar listrik beberapa tahun terakhir, maka yang menjadi pertanyaan adalah bagaimana efisiensi terhadap sebuah motor yang dilakukan rewinding. Efisiensi adalah ukuran efektifitas seberapa banyak energi listrik yang diserap oleh motor diubah menjadi tenaga mekanis yang termanfaatkan dibandingkan dengan rugi-rugi daya yang timbul pada motor. Pada penelitian ini telah dilakukan sebuah evaluasi efisiensi terhadap motor-motor induksi satu fase berdaya kurang dari 1 hp yang dilakukan perbaikan dengan cara rewinding secara manual. Menggunakan metode copy terhadap tiga buah motor induksi, hasil penelitian menunjukkan secara keseluruhan nilai efisiensi motor induksi yang dilakukan rewinding memiliki nilai efisiensi yang lebih baik. Nilai efisiensi motor induksi satu fase berdaya kurang dari 1 Hp yang dilakukan perbaikan dengan cara rewinding mengalami peningkatan rata-rata +16.93 % dengan rentang +2.42 % s.d. +20.11 %.
MODIFICATION OF TWO POLES SINGLE PHASE INDUCTION MOTOR AS WIND PICO GENERATOR Fauzun Atabiq; Budiana Budiana; Arif Febriansyah Juwito; Irfan Syahri; Ihsan Saputra
JURNAL INTEGRASI Vol 11 No 1 (2019): Jurnal Integrasi - April 2019
Publisher : Politeknik Negeri Batam

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (472.89 KB) | DOI: 10.30871/ji.v11i2.1132

Abstract

As an alternative energy, the potential of wind power in Indonesia is quite high. Some of the constraints of wind power include the presence of intermittent winds, the average wind speed in the Indonesian is relatively low, or only certain areas that have moderate to high wind speeds, so that winds that are not too tight can cause the turbines not spinning. This study is about modifying a two pole single phase induction motor as a wind pico generator. Modifications made to the squirrel cage rotor induction motor become two poles axial flux permanent magnet rotors. The test results show that a two pole pico generator is not suitable to be applied to wind power units. Electric power produced by high-speed prime mover, above 1000 rpm only 2.53 Watts. Whereas when it is operated at low speed, less than 200 rpm, the maximum output power power only 44 mW.
Preliminary Study of the Vertical Axis Wind Turbine (VAWT) Prototype at Urban Area Irwanto Zarma Putra; Fauzun Atabiq; Didi Istardi; Ridwan Ridwan; Arif Febriansyah Juwito; Muhammad Agil Wildan; Muhammad Ridlo Alfianto; Rahman Hakim
JURNAL INTEGRASI Vol 13 No 1 (2021): Jurnal Integrasi - April 2021
Publisher : Politeknik Negeri Batam

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30871/ji.v13i1.2754

Abstract

This research complements the shortcomings of PLTB, namely by adding a Monitoring System to the Wind Power Plant at Batam State Polytechnic. By addition of sensors, installations, and a control panel containing instruments for monitoring wind conditions, Savonius turbine rpm, and pico-generator output electrical characteristics. The method used is conventional, starting from mechanical design, program development, and installation to testing. This study's preliminary results indicate that wind at the PLTB Polibatam location is not continuous. It does not occur, even though the maximum wind speed can reach 8.9 m / s. The implementation of the savonius-type wind turbine in this study can generate electricity around 87.83 kW / week or about 0.61 kW / hour.
Trainer Kit for Velocimetry Thermodynamics Lab Dice Throwing Muhammad Prihadi Eko Wahyudi; Natalia Parhusip; Fauzun Atabiq; Qoriatul Fitriyah
JURNAL INTEGRASI Vol 15 No 1 (2023): Jurnal Integrasi - April 2023
Publisher : Pusat Penelitian dan Pengabdian Masyarakat Politeknik Negeri Batam

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30871/ji.v15i1.5258

Abstract

The Trainer Kit is one of the tools that supports the learning process of the Thermodynamics Lab Course. The objects ejection tool design is created with a 3D printed catapult movement system. The main components of the objects Ejection Speed ​​Trainer Kit are: Use the ultrasonic sensor HC-SR04 as a guide for the desired firing distance, a stopwatch as a measure of time spent throwing objects using the TTP223's capacitive touch as a start and stop clock. Load cell as a measure of the weight of the objects. Meter reading results are displayed on a 20x4 LCD with an i2c module and calculation of velocity values ​​using Visual Basic 6.0. Results of a load cell experiment measuring 6 different materials weighing between 5 and 63 g with an average measurement error of 1.2%. As result of ultrasonic examination measured in increments of 3 to 100 cm, the measurement error is 0% at the maximum distance of 70 cm, and the error is 1.1% at 70 cm or more. The result of the timer experiment using TTP223 in 15 tests has an arithmetic error of 0.37%.