Claim Missing Document
Check
Articles

Found 16 Documents
Search

The Effect of Concentration and Timing of Application of Green Tonik Foliar Fertilizer on theGrowth and Yield of Cucumber (Cucumis sativusL.) Mercy Variety Rahman Hakim
Agrifor : Jurnal Ilmu Pertanian dan Kehutanan Vol 17, No 2 (2018): Oktober
Publisher : Universitas 17 Agustus 1945 Samarinda

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.31293/af.v17i2.3618

Abstract

This experiment aims to: (1) to study of the effect of concentration and application timing of Green Tonik foliar fertilizeras well as their interaction on the growth and yield of cucumber plants; and (2) to find proper concentration and application timing of Green Tonik foliar fertilizer for better growth and yield of cucumber plants.The experiment carried out from March 2016 to May 2016, in the Village of Muara Bengkal Ilir, Muara Bengkal Subdistrict, East Kutai District.  It applied Completely Randomized Block Design with factorial experiment 4 x 3 and three replications.  The first factor was the concentration of the Green Tonik  foliarfertilizer (K) consists of 4 levels, namely: no Green Tonik foliar fertilizer application (k0), 1 ml l-1 water(k1), 2 ml l-1 water(k2), and 3 ml l-1 water(k3). The second factor wasinterval of the application time of Green Tonik foliar fertilizer(W) consists of 3 levels: 5, 10, 15, 20, and 25 days after planting (w1), 7, 14, 21, 28, and 35 days after planting (w2), and 10, 20, 30, 40, and 50 days after planting (w3).Result of the experiment revealed that : (1) concentration of Green Tonik foliar fertilizer application was affected significantly to very significantly on plant lenght at 30 and 45 days after planting, days of plant flowered, number of fruits per plant, diameter of fruit, weight of one fruit, and production of fruits, but no significant on the plant lenght at 15 days after planting, and lenght of fruit.  The highest production of fruit is attained by the 2 ml l-1 water (k3), namely 54,67 Mg ha-1, In reverse, the least production is attained by without Green Tonik foliar fertilizer (k0), namely 24,00 Mg ha ̵ ¹; (2) interval of Green Tonik foliar fertilizer application time was no significant on the plant lenght at 15 and 45 days after planting, days of plant flowered, number of fruits per plant, lenght of fruit, diameter of fruit, weight of one fruit, and production of fruit, but affected significant on the plant lenght at 30 days after planting; and (3) interaction between concentration and application timing of Green Tonik foliar fertilizer was no significant on the all parameters observed.
PAPER DENGAN JUDUL BERIKUT DITARIK DARI PUBLIKASI JURNAL INTEGRASI (RANCANG BANGUN PURWA-RUPA CMM TOWER FIXTURE SEBAGAI DASAR MEDIA PEMBELAJARAN GD&T) Auliana Diah Wilujeng; Rahman Hakim
JURNAL INTEGRASI Vol 12 No 1 (2020): Jurnal Integrasi - April 2020
Publisher : Politeknik Negeri Batam

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (388.22 KB) | DOI: 10.30871/ji.v12i1.1515

Abstract

PAPER DENGAN JUDUL BERIKUT DITARIK DARI PUBLIKASI JURNAL INTEGRASI (RANCANG BANGUN PURWA-RUPA CMM TOWER FIXTURE SEBAGAI DASAR MEDIA PEMBELAJARAN GD&T)
Pemberian Mini House (Destilator) Air laut kepada masyarakat Pantai Setokok, Batam, Guna membantu dalam penyediaan stok air bersih (Air Tawar), dan mendukung Parawisata Muhammad Zainuddin Lubis; Yeni Rokhayati; Supardianto Supardianto; Danar Irianto; Wenang Anurogo; Budiana Budiana; Siti Noor Chayati; Widya Rika Puspita; Swono Sibagariang; Jhon Hericson Purba; Dodi Prima Resda; Rahman Hakim; Muhammad Ghazali
Jurnal Pengabdian kepada Masyarakat Politeknik Negeri Batam Vol 2 No 2 (2020): Jurnal Pengabdian kepada Masyarakat Politeknik Negeri Batam
Publisher : Pusat P2M Politeknik Negeri Batam

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30871/abdimas.v2i2.2601

Abstract

Water destilator merupakan alat yang digunakan untuk menyuling air laut menjadi air tawar. Konsepnya sederhana dan serupa dengan siklus hidrologi, yaitu dengan menguapkan air laut dengan cara dipanaskan, yang kemudian uap air tersebut diembunkan dan dikumpulkan ke dalam suatu wadah penampung sehingga didapatkan air tawar. Sumber panas yang dipergunakan berasal dari energi yang beragam: minyak, gas, listrik, tenaga matahari dan lainnya, namun dikarenakan menerapkan konsep ramah lingkungan alat ini hanya mengandalkan cahaya matahari sebagai energinya. Alat destilator ini adalah alternatif sederhana yang ekonomis dan dapat digunakan dalam skala rumah tangga serta ramah lingkungan. Alat ini merupakan pengganti sistem destilasi pabrik dengan harga yang relatif mahal dan masih sulit dijangkau oleh penduduk Indonesia. Jenis teknologi tersebut cukup sulit karena teknologinya rumit dan membutuhkan investasi dan estimasi dana yang tinggi dalam skala rumah tangga. Destilasi dapat terjadi dengan memanfaatkan potensi alam yaitu sinar matahari menggantikan bahan bakar minyak dan gas alam untuk mengubah fase uap air laut. Karena suhu yang diperlukan untuk mengubah fase air laut menjadi uap tidak terlalu besar (dibawah 100oC) atau di bawah satu tekanan atmosfir (1 atm), maka pemanfaatan energi matahari adalah solusi alternatif yang dipilih sesuai dengan kondisi Indonesia yang terletak pada daerah katulistiwa dan beriklim tropis mempunyai jumlah sinar matahari yang cukup.
Pembuatan Coupling 3 ????⁄????” Mod EU Di PT Elnusa Fabrikasi Konstruksi Benny Haddli Irawan; Yudy Pratama; Budi Baharudin; Rahman Hakim; Hanifah Widiastuti; Widodo Widodo; Ihsan Saputra; Fedia Restu
Jurnal Teknologi dan Riset Terapan (JATRA) Vol 4 No 1 (2022): Jurnal Teknologi dan Riset Terapan (JATRA) - June 2022
Publisher : Politeknik Negeri Batam

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30871/jatra.v4i1.3743

Abstract

Coupling 3 1⁄2” Mod EU (Modified External Upset) is an API 5CT (American Petroleum Institute) product specially made at customer's request, this product is a product that is rarely made at PT ELNUSA FABRIKASI KONSTRUKSI. In this API 5CT product, it is a Modified EU Coupling product which is designed to use an additional ring seal for extra protection on the oil-flowing pipe. To make a 3 1⁄2” Mod EU Coupling, use a CNC lathe by going through the Facing, Blanking ID, Threading ID and Grooving ID processes. The purpose of making this final project is to find out the process carried out and the use of the right method in the manufacture of 3 1⁄2” Mod EU Couplings at PT Elnusa Fabrication Construction, as a learning media or data retrieval, especially when making other Coupling products.
Analisis Proses Penentuan Kelayakan dan Pengamanan Penggunaan Overhead Crane Menggunakan Metode Pemeriksaan dan Pengujian Teknis K3 Annisa Fyona; Miduk Parulian Nababan; Budi Baharudin; Rahman Hakim
Jurnal Teknologi dan Riset Terapan (JATRA) Vol 4 No 1 (2022): Jurnal Teknologi dan Riset Terapan (JATRA) - June 2022
Publisher : Politeknik Negeri Batam

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30871/jatra.v4i1.3795

Abstract

In the world of industry, you can find many tools or machines that are used to simplify the process of human work. One type of tool that is widely used is a lifting equipment. Lifting equipment are equipment that are made and installed to lift, down, set and hold workpieces or load. One example of a lifting equipment is an overhead crane. Most overhead cranes are installed on the roof of the building (indoors) but can also be used outdoors. Along with the time to use an overhead crane, the longer it will definitely experience a decrease in quality both in terms of components and functions, it is necessary to control the feasibility management system and use permit. Based on the regulations of the Ministry of Manpower is Permenaker no. 8 tahun 2020 about K3 of lifting equipment and transport equipment. Which each lifting and transport equipment’s before being operated should be inspected and tested in advance, as well as periodic testing is carried out in accordance with the test standards have determined. The final task research uses descriptive qualitative analysis method, which is to get data by direct observation on the tool. When inspection and testing has been carried out according to standards, the overhead crane will receive a certificate and a safe use permit.
Penerapan IbM: Pembuatan Studi Kelayakan Rute Pelayaran Batam Marine Ambulance Muhammad Zainuddin Lubis; Rahman Hakim; Hanifah Widiastuti; Lalu Giat Juangsa Putra; Sapto Wiratno Satoto; Benny Haddli Irawan; Ihsan Saputra; Naufal Abdurrahman; Budi Baharudin
Jurnal Pengabdian kepada Masyarakat Politeknik Negeri Batam Vol 4 No 1 (2022): Jurnal Pengabdian kepada Masyarakat Politeknik Negeri Batam
Publisher : Pusat P2M Politeknik Negeri Batam

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30871/abdimas polibatam.v4i1.3592

Abstract

Kegiatan pengabdian dengan ambulans Marine sangat mendukung kegiatan penanggulangan dalam mengatasi gawat darurat terutama di wilayah kepulauan Riau, Batam. Pengabdian ambulans marine ini melakukan beberapa metode pendekatan, yaitu melakukan a. Manajemen Resiko kegiatan, b. Studi Literatur dan Identifikasi Masalah, c. Studi Lapangan dan Pengumpulan Data, d. Analisa dan Pembahasan, dan e. Pembahasan dan kesimpulan. Kegiatan pengabdian ini merupakan kegiatan lanjutan yang sudah dilakukan saat tahun 2020 oleh tim pengerjaan ambulans marine sebelumnya. Kegiatan ini juga melakukan perencanaan alur untuk pengantaran via laut/ perairan yang ada di Kepulauan Riau. Kegiatan perawatan juga dilakukan dalam kegiatan pengabdian, sehingga wahana atau ambulans dapat diketahui kondisi kelistrikan, permesinan, serta kegiatan pengabdian ini juga melakukan sosialisasi menggunakan media video, sehingga masyarakat dapat mengetahui kegiatan ini, dan juga menjadi implementasi kegiatan Batam tanggap cepat gawat darurat.
Perawatan dan Perbaikan Dalam Upaya Peremajaan Kapal Batam Marine Ambulance Fauzun Atabiq; Irwanto Zarma Putra; Muhammad Syafei Gozali; Arif Wahyu Budiarto; Muhammad Nurhidayat; Kartika Kartika; Ari Wibowo; Nugroho Pratomo Ariyanto; Nurul Laili Arifin; James Siregar; Wowo Rossbandrio; Muhammad Andi Nova; Rizky Pratama Hudhajanto; Annisa Fyona; Yogantara Yogantara; Meida Perwira Antartika; Rahman Hakim
Jurnal Pengabdian kepada Masyarakat Politeknik Negeri Batam Vol 4 No 1 (2022): Jurnal Pengabdian kepada Masyarakat Politeknik Negeri Batam
Publisher : Pusat P2M Politeknik Negeri Batam

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30871/abdimas polibatam.v4i1.3759

Abstract

Marine ambulance, as medically equipped vehicle which tranports patient to referral facilites, is very important in Batam archipelago. Routine maintenance activities is conducted to ensure all systems function properly. The maintenance includes maintenance of ship mechanics and ship engines, electrical systems, and hull cleaning. Maintenance standard operating procedure (SOP) is composed to help ship crew conducting ship maintenance. The maintenance activity repairs system problems successfully and appreciated by ship crew, LAZ Batam, and Awal Bros Hospital as service provider; and community who benefited by the service. Healthcare service operates well although some respondents think there is lack of equipments. Safety equipment and medical equipment are not enough for 13% and 20% respondents, respectively. However, all respondent think that the maintenance activity has repaired ship system and ensure ship to operate properly, and deliver healthcare service well.
Analisa Kekasaran Permukaan Produk Mesin Cetak Tiga Dimensi Dengan Material Acrylonitrile Butadiene Styrene Terlapis Cat Emulsi Adhe Aryswan; Rahman Hakim; Muhammad Rezki Saputra
Jurnal Teknologi dan Riset Terapan (JATRA) Vol 1 No 2 (2019): Jurnal Teknologi dan Riset Terapan (JATRA) - December 2019
Publisher : Politeknik Negeri Batam

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1111.262 KB) | DOI: 10.30871/jatra.v1i2.1779

Abstract

Kemajuan teknologi menuntut industri manufaktur untuk dapat menghasilkan produk yang bentuknya lebih rumit dalam waktu lebih cepat. Teknik additive manufacturing atau percetakan tiga dimensi dapat mengatasi masalah ini, dengan mencairkan material kemudian dituang sedikit demi sedikit sebagai lapisan dalam proses pembuatannya. Produk yang dihasilkan memiliki permukaan yang kasar karena lapisan-lapisan yang dibentuk mesin cetak. Untuk menyesuaikan permukaan tersebut, dapat dilakukan pelapisan oleh cat emulsi. Studi ini meneliti kekasaran permukaan rata-rata (Ra) produk mesin cetak tiga dimensi dari bahan acrylonitrile butadiene styrene yang dilapisi cat tembok dan cat semprot dengan variasi waktu perendaman 5, 10, dan 15 menit. Hasil karakterisasi Ra oleh Surface Roughness Tester menunjukkan tingkat kekasaran permukaan sampel yang dilapisi selama 15 menit lebih rendah daripada 5 dan 10 menit. Nilai Ra sampel yang dilapisi cat semprot adalah 3,035 µm, lebih rendah daripada sampel terlapis cat tembok yaitu 2,650 µm untuk waktu perendaman yang sama yaitu 15 menit.
Studi Experimen Mula: Analisa Kekasaran Permukaan Baja ST 37 Terhadap Variasi Kuat Arus Listrik Ita Wijayanti; Rahman Hakim; Widodo Widodo
Jurnal Teknologi dan Riset Terapan (JATRA) Vol 1 No 2 (2019): Jurnal Teknologi dan Riset Terapan (JATRA) - December 2019
Publisher : Politeknik Negeri Batam

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (734.114 KB) | DOI: 10.30871/jatra.v1i2.1781

Abstract

Proses pemesinan konvensional tidak mampu mengakomodasi pembuatan produk yang memiliki desain kompleks dan membutuhkan tingkat ketelitian yang tinggi. Teknologi electrical discharge machining (EDM) merupakan proses pemesinan nonkonvensional yang mampu mengakomodasi kebutuhan-kebutuhan tersebut. Dengan EDM maka stres mekanis, chatter dan masalah getaran saat proses pemesinan dapat dikurangi. Penelitian ini bertujuan untuk mengetahui pengaruh variasi arus listrik yang berbeda (3A, 6A dan 12A) saat pemesinan EDM terhadap nilai kekasaran (Ra) permukaan benda kerja (baja ST37). Elektroda yang digunakan yaitu berbahan baku tembaga. Hasil penelitian menunjukkan bahwa Ra terkecil (3,452 μm) diperoleh pada variasi arus 3A, sedang pada arus listrik 6A diperoleh Ra sebesar 4,789 μm dan Ra sebesar 7,313 μm pada arus listrik 12A. Semakin besar arus listrik yang digunakan selama pemesinan EDM maka semakin kasar permukaan benda kerja yang dihasilkan. Kata Kunci: EDM, Nilai Kekasaran, Tembaga, ST37
Potensi Novelty Bidang Injection Mold Design: Visualisasi Pemetaan Bibliometric Rahman Hakim; Widodo Widodo; Benny Haddli Irawan; Ahmad Nurasa; Amar Makruf
Jurnal Teknologi dan Riset Terapan (JATRA) Vol 2 No 2 (2020): Jurnal Teknologi dan Riset Terapan (JATRA) - December 2020
Publisher : Politeknik Negeri Batam

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30871/jatra.v2i2.2095

Abstract

This study aims to determine the direction of development in the world of Mold & Dies design in the world. Data searches were carried out through science direct databases using the design of molds and dies as keywords with a limitation of open access journals between 2015 - 2020. The results were comprehensively analyzed based on year, publisher's name, institution, and the country as well as research subjects. Files from Mendeley software are saved in Reference Manager Format (.RIS) format which is processed into VOSviewer software to find out the bibliometric map. The results revealed that the highest number of publications is in a procedia manufacturing journal. The most contributing country in the European continent indexed in Scopus is Germany. Within the output in the form of network visualization, it is found that several novelty potentials are in line with the direction of the development of the study with the parameters of the number of population and the year of the research output. Publications on the most similarity and chance of novelty on research topics are in Cluster 1, which consists of Energy Efficiency, Decision Process, Plastic Materials, and Sustainability.Keywords: Novelty, Injection Mold Design, Bibliometric Maping, VOSviewer