Garuda - Garba Rujukan Digital

The Effect of Furnace Temperature and Precursor Concentration Ratio to The Characteristics of Nanocomposite ZnO-Silica Iva Maula; Widiyastuti Widiyastuti; Tantular Nurtono; Fadlilatul Taufany; Siti Machmudah; Sugeng Winardi
IPTEK Journal of Proceedings Series Vol 1, No 1 (2014): International Seminar on Applied Technology, Science, and Arts (APTECS) 2013
Publisher : Institut Teknologi Sepuluh Nopember

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.12962/j23546026.y2014i1.323

Zinc Oxide is a semiconductor with relatively non-toxic, cheap and abundant properties which can be applied to LEDs. ZnO colloids are unstable due to further chemical reactions and coagulation so the addition of silica is needed to inhibit the growth of ZnO. ZnO was synthesized using sol-gel method by hydrolyze zinc acetate dihydrate in ethanol solution. Silica colloids was prepared by dissolving waterglass in distilled water at a temperature of 60 °C then passed into cation resin that has been activated using 2N HCl for ion exchange with Na+ to H+. In this study, the spray drying method was used to produce ZnO-silica nanocomposite. Morphological characterization of particles formed was analyzed using Scanning Electrostatic Microscope (SEM) (Zeiss Evo MA LS, Cambridge, England). X-Ray Diffraction (XRD) (Cu-Kα 1.54 A0, 40 kV, 30 mA, X’pert Pro, PAN alytical, Netherlands) and Fourier Transform Infrared (FTIR) (Therniscientific Nicolet iS10, US) were used to analyze the crystallinity and group functionalization, respectively. The results show that more particles are formed on 10% concentration volume of ZnO colloids rather than 5%.

Computational Fluid Dynamics Simulation of Clearance Effect in High Solid Loading Polydisperse Solid-Liquid Mixing Iman Mukhaimin; Tantular Nurtono; Sugeng Winardi
IPTEK Journal of Proceedings Series No 2 (2017): The 2nd Internasional Seminar on Science and Technology (ISST) 2016
Publisher : Institut Teknologi Sepuluh Nopember

A high solid loading concentration of solid-liquid mixing was investigated to observe the effect of ratio C, Clearance, and T, diameter tank, with C/T 0.33; C/T 0.25 and C/T 0.17 on local volume of hydrodynamic and spatial distribution of polydisperse solid suspension using CFD, Computational Fluid Dynamics. The 45o pitch blade turbine, diameter 0.5T, with down pumping flow simulation was used to remove solid particle from bottom of the tank. The tank is also equipped with four baffle with the size of 0.1T.. A solid-liquid mixing consists of five fractions of glass beads with equal proportion (X1=X2=X3=X4=X5=0.2X) have 40% wt total solid concentration with liquid fraction is aqueous solution of NaCl. The effect of ratio C/T at impeller speed 612 rpm create a flow pattern in the tank different. Effect ratio C / T also indicated the distribution on solid had a good uniformity index when N≥ Njs, just suspended speed. The highest uniformity was obtained on C/T 0.17. it also made difference power consumption on each geometry with C/T 0.17, 0.25, and 0.33 respectively are 251.18, 238.13, and 270.65watt.

Computational Fluid Dynamics Simulation of Clearance Effect in High Solid Loading Polydisperse Solid-Liquid Mixing Iman Mukhaimin; Tantular Nurtono; Sugeng Winardi
IPTEK Journal of Proceedings Series No 2 (2017): The 2nd Internasional Seminar on Science and Technology (ISST) 2016
Publisher : Institut Teknologi Sepuluh Nopember

A high solid loading concentration of solid-liquid mixing was investigated to observe the effect of ratio C, Clearance, and T, diameter tank, with C/T 0.33; C/T 0.25 and C/T 0.17 on local volume of hydrodynamic and spatial distribution of polydisperse solid suspension using CFD, Computational Fluid Dynamics. The 45o pitch blade turbine, diameter 0.5T, with down pumping flow simulation was used to remove solid particle from bottom of the tank. The tank is also equipped with four baffle with the size of 0.1T.. A solid-liquid mixing consists of five fractions of glass beads with equal proportion (X1=X2=X3=X4=X5=0.2X) have 40% wt total solid concentration with liquid fraction is aqueous solution of NaCl. The effect of ratio C/T at impeller speed 612 rpm create a flow pattern in the tank different. Effect ratio C / T also indicated the distribution on solid had a good uniformity index when N≥ Njs, just suspended speed. The highest uniformity was obtained on C/T 0.17. it also made difference power consumption on each geometry with C/T 0.17, 0.25, and 0.33 respectively are 251.18, 238.13, and 270.65watt.

Effect of Mixing Time to Homogeneity of Propellant Slurry Luthfia H. Abdillah; Sugeng Winardi; Sumarno Sumarno; Tantular Nurtono
IPTEK Journal of Proceedings Series No 1 (2018): 3rd International Seminar on Science and Technology (ISST) 2017
Publisher : Institut Teknologi Sepuluh Nopember

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.12962/j23546026.y2018i1.3515

Propellant is a rocket fuel that can be solid or liquid. This research focused on composite solid propellant that was made from solid and liquid materials become a slurry. Homogeneity of the propellant slurry is important to investigate because it can affect specification and performance of the propellant. This research objective was to study effect of mixing time to homogeneity of propellant slurry that was processed by horizontal sigma blade mixer. Density data were used to assess the homogeneity and stated as degree of homogeneity. The result showed that the mixing time affect the density values and it was obtained the most homogeneous slurry was at total mixing time 135 minute

Title

Found 4 Documents
Search
Journal : iptek journal of proceedings series

Abstract

Abstract

Abstract

Abstract

Title Search

Found 4 Documents Search Journal : iptek journal of proceedings series

Abstract

Abstract

Abstract

Abstract

Title

Found 4 Documents
Search
Journal : iptek journal of proceedings series