Claim Missing Document
Check
Articles

Found 30 Documents
Search

SYNTHESIS OF RUTILE TIO2 NANOPARTICLES BY CO-PRECIPITATION METHOD Nazaruddin Nasution; Aida Fitri
FISITEK: Jurnal Ilmu Fisika dan Teknologi Vol 2, No 2 (2018)
Publisher : Universitas Islam Negeri Sumatera Utara Medan

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (324.168 KB) | DOI: 10.30821/fisitek.v2i2.1808

Abstract

Abstract. The objective of this research is to produce rutile TiO2 nanoparticles by co-precipitation method and to determine its characterization using Scanning Electron Microscopy (SEM), Energy Dispersive X-ray Spectroscopy (EDS), X-ray Diffractometry (XRD), and Particle Size Analysis (PSA) methods. Synthesis of rutile TiO2 nanoparticles by co-precipitation method in this study was initiated by mixing 15% TiCl3 solution into distilled water while stirring at constant speed for some time. Then, pH is adjusted to 11-13 by dripping ammonia (NH4OH) solution while continuing to stir. The precipitate (white gel) is then dried in the oven and crushed to produce TiO2 powder. The morphology of the TiO2 particles obtained is spherical and tends to agglomerate. The average particle size of TiO2 produced is 192.2 nm. The EDS results show that the percentage of Ti mass in TiO2 particles is 59.52%. Based on XRD analysis, there are two phases formed namely anatase and rutile with a tetragonal crystal system.Keywords: Co-precipitation method, nanoparticles, and rutile.
DESIGN OF KITCHEN SECURITY SYSTEM BASED ON ATMEGA32 MICROCONTROLLER Aulia Khusnul Arif Z.A; Nazaruddin Nasution; Abdul Halim Daulay
FISITEK: Jurnal Ilmu Fisika dan Teknologi Vol 3, No 2 (2019)
Publisher : Universitas Islam Negeri Sumatera Utara Medan

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30821/fisitek.v3i2.6853

Abstract

The kitchen is one of the places most concerned by every community because the biggest fire potential in the house lies in the kitchen, the source of fire that often causes fires in the kitchen is a stove and gas. Therefore we need a design of a kitchen security system based on the ATmega32 microcontroller using flame sensors, MQ-2 and MQ-6. This study aims to produce a performance tool that will detect any movement of fire, gas, and smoke using an Early Warning System. The warning in the form of an alarm sounds, the fan turns, and the door opens automatically. Sensor detection is designed with 4 conditions namely Normal, Caution, Alert and Danger. The results of testing using the Flame sensor found a wave range from 22 nm to 1022 nm from normal to hazardous conditions, the MQ-2 found the results of testing from the ADC (Analog Digital Converter) with concentrations from 0 ppm to 130 ppm from normal to hazardous conditions, and the MQ-6 test results were obtained from the ADC (Analog Digital Converter) with concentrations from 0 ppm to 520 ppm from normal to dangerous conditions. Keywords : Kitchen, ATmega32, Flame sensor, MQ-2, and MQ-6.
WENNER'S CONFIGURATION GEOELECTRIC METHOD FOR THE INTERPRETATION OF THE SUBSURFACE STRUCTURES OF PANUNGKIRAN VILLAGE Aulia Farihanum; Nazaruddin Nasution; Abdul Halim Daulay
FISITEK: Jurnal Ilmu Fisika dan Teknologi Vol 4, No 2 (2020)
Publisher : Universitas Islam Negeri Sumatera Utara Medan

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30821/fisitekfisitek.v4i2.9616

Abstract

A research has been carried out which aims to determine the subsurface structure using the geoelectric method in Panungkiran Village, Kab.  Deli Serdang, Prov.  North Sumatra Geoelectric data retrieval uses the Wenner configuration to determine the distribution and depth of subsurface structures in Panungkiran Village, Deli Serdang Regency.  Prov.  North Sumatra Data collection is 1 track with a length of 90 meters, Data processing in the study using MS office software Excel Notepad, and RES2DINV The results of the measurements consist of several types which are distinguished based on the range of resistivity values, namely in the range of 34.0-3188 2m interpreted by lithological layers  topsoil (34.0-65.1 Ωm), sandstone (65.1-1252 Ωm) weathered travertine limestone (125-456 Ωm), fresh trvertine limestone (456-3188 Ωm), and resistivity >3188  Qm is interpreted as a cave at a depth of 9-12 meters.
Sistem Otomatisasi Jemuran Pakaian dengan Sensor Hujan dan Sensor LDR Berbasis Arduino Uno Nazaruddin Nasution; Diva Moniva Marpaung; Mulkan Iskandar Nasution
Jurnal Fisika Unand Vol 12 No 1 (2023)
Publisher : Universitas Andalas

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (324.113 KB) | DOI: 10.25077/jfu.12.1.124-130.2023

Abstract

Pemanasan global saat ini telah menyebabkan cuaca menjadi kurang menentu, sehingga musim kemarau dan hujan tidak lagi dapat diprediksi. Kondisi cuaca yang tidak menentu dapat mempersulit proses pengeringan pakaian. Oleh karena itu, perlu dirancang sistem otomatisasi penjemuran pakaian berbasis mikrokontroler arduino uno yang menggunakan sensor hujan dan sensor LDR. Penelitian ini bertujuan untuk mengembangkan alat kinerja yang akan menggunakan sistem otomatis untuk mendeteksi apakah ada ada hujan, tidak ada cahaya atau cuaca dalam keadaan mendung. Sistem otomatis berupa jemuran yang menggunakan motor stepper yang akan menarik tali jemuran masuk atau keluar dan pemberitahuan dari DFPlayer Mini. Desain pendeteksian cahaya hujan memiliki 4 status: hujan – siang, cerah – malam, cerah – siang, dan hujan – malam. Dalam setiap kasus, motor stepper menarik tali jemuran masuk atau keluar. Hasil dari penelitian ini menunjukkan bahwa sistem otomatisasi dapat mendeteksi besar curah hujan yaitu 0,1 mm – 817 mm, dan besar intensitas cahaya yaitu 5 Lux – 506 Lux.
PROTOTIPE SMART HOME DENGAN IoT (INTERNET of THINGS) BERBASIS WEMOS D1 MINI Rendy Fadli Iswara; Mulkan Iskandar Nasution; Nazaruddin Nasution
JISTech (Journal of Islamic Science and Technology) Vol 7, No 2 (2022)
Publisher : UIN Sumatera Utara Medan

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30829/jistech.v7i2.14662

Abstract

Research has been carried out prototype Smart home with IoT (Internet of Things) based on Wemos D1 Mini which can simulate the application of Smart home that can be accessed via the internet by connecting electronic devices to the internet with a Wemos D1 mini microcontroller, while processing all data in the form of input and output. , with control system via wemos and supported by MQ-2 sensor, flame sensor, PIR sensor, relay, buzzer, water pump and fan. The method applied in this research is the monitoring and control system development carried out in this study, namely: the design is equipped with several features, namely sending notifications to the SmartPhone in the form of reports and settings through the application so that it can help users to find out and get information about the conditions that occur at home. , this design is also equipped with an MQ-2 sensor when the sensor detects the 5V fan will turn on to suck gas / smoke out of the room, as a continuation if a gas leak occurs, this prototype is also equipped with a Flame sensor which can turn on the water pump as a fire suppression by The concentration of the sensor works at a wavelength of less than 450 nm, it is also equipped with a PIR Sensor that will turn on an alarm if an intruder is detected in the house and on the tile.
Penentuan Daerah Potensi Geothermal Dengan Menggunakan Metode Seismik Di Madina Nazaruddin Nasution
EINSTEIN (e-Journal) Vol 8, No 1 (2020): EINSTEIN (e-Journal)
Publisher : Universitas Negeri Medan

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (286.126 KB) | DOI: 10.24114/einstein.v8i1.15930

Abstract

ABSTRACT: Puncak Sorik Marapi Subdistrict Area is a highland area which is located at 2,145 meters above sea level at coordinates 0,41- 11 South Latitude  and 99,32- 13 East Longitude, in the area under study is the peak area which is still being said relatively  flat and can be used as a power plant area. Based on this, it is necessary to conduct the research about the structure of the soil layer. Primary seismic data retrieval is performed at four points which at each point is rare of 200 m. The data obtained were analyzed using MonoST software and then converted to Mseed format using Datapro software, files with Mseed format were processed using Geopsy software. From the data obtained the frequency value of 0.949 Hz to 1.421 Hz concludes that the classification of soil types in the research area is included in soft oil types with surface sediment thickness is very thick. This is in accordance with conditions in the field in the form of geothermal location with silt due to geothermal activity. Data of kg values obtained at points 22.7 – 30.4 at 4 points can be said to be low, it is concludes the seismic vulnerability that will be experience by the research site is insignificant or tends will not happen the fault or landslide if it occurs the earthquake. From the PGA values obtained in the range of 8.3 – 9.1, these values fall into the very small risk category based on the earthquake risk level classification.
PERANCANGAN SISTEM KENDALI OTOMATIS PADA RUMAH PINTAR (SMART HOME) BERBASIS ARDUINOATMEGA 328 Abdul Halim Daulay; Nazaruddin Nasution
EINSTEIN (e-Journal) Vol 11, No 1 (2023): EINSTEIN (e-Journal)
Publisher : Universitas Negeri Medan

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (154.312 KB) | DOI: 10.24114/einstein.v11i1.42773

Abstract

Telah dilakukan penelitian Prototipe Smart home dengan arduino ATMega 328 yang dapat mensimulasikan penerapan Smart home yang aktif  dengan cara menyambungkan perangkat-perangkat elektronik ke internet dengan mikrokontroler, saat memproses seluruh data berbentuk Input dan Output, dengan sistem kontrol melalui arduino  dan didukung dengan sensor MQ-2, flame sensor, Sensor PIR, relay, buzzer, pompa air, sensor PH, Ultarsonik PH, RTM dan kipas. Metode yang diterapkan pada penelitian ini adalah monitoring dan sistem kontrol pengembangan yang membantu pengguna untuk mengetahui dan mendapat informasi mengenai kondisi yang terjadi di rumah, perancangan ini juga dibekali dengan sensor MQ-2 ketika sensor melakukan pendeteksian maka kipas 5 V akan hidup untuk menghisap gas/asap keluar ruangan, sebagai kelanjutan jika terjadinya kebocoran gas maka prototipe ini dibekali juga dengan Flame sensor yang dapat menghidupkan pompa air sebagai penanggulangan kebakaran dengan konsentrasi sensor bekerja pada panjang gelombang kurang dari 450 nm, juga dibekali dengan sensor PIR yang akan menghidupkan alarm jika terdeteksi adanya penyusup di dalam rumah dan di genteng. Dan terakhir Smarthome ini juga di bekali kolam pintar yang diguanakan untuk mempermudah kontroling jika ingin  membdidayakan ikan. 
PROTOTYPE ALAT PENDETEKSI ASAP ROKOK DAN PENETRALISIR UDARA PADA KAMAR MANDI SEKOLAH MAS ISLAMIYAH SUNGGAL Nazaruddin Nasution; Mulkan Iskandar Nasution; Dewi Kesuma Wati turnip
EINSTEIN (e-Journal) Vol 11, No 1 (2023): EINSTEIN (e-Journal)
Publisher : Universitas Negeri Medan

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (332.328 KB) | DOI: 10.24114/einstein.v11i1.38759

Abstract

Data dari Yayasan Kanker Indonesia (YKI) ditemukan27,1% dari 1.961 pelajar laki-laki SMA/SMK, sudahterbiasa dengan rokok. Oleh karena itu, dibutuhkan suaturancang bangun alat pendeteksi asap rokok dan pentralisirudara pada kamar mandi sekolah berbasis mikrokontrolerarduino uno menggunakan sensor asap MQ-2. Penelitian inibermaksud agar dihasilkan sebuah alat yang dapatmendeteksi asap rokok dalam kamar mandi menggunakansistem peringatan. Adapun peringatan itu berupa dfPlayermini memberikan perintah untuk menyalakan buzzer, relaimemberikan perintah agar kipas berputar, dan LED merahakan menyala. Pendeteksian sensor dirancang dengan 2 keadaan yaitu, Normal tidak terdeteksi asap rokok dan Berbahaya asap rokok terdeteksi. Hasil dari pengujianmenggunakan sensor asap MQ-2 didapati range 0-79 keadaan normal tidak terdeteksi asap rokok, pada range<80 keadaan berbahaya terdeteksi asap rokok.
ANALISIS LAPISAN BAWAH PERMUKAAN SEBAGAI PERENCANAAN PEMBANGUNAN MENGGUNAKAN METODE GEOLISTRIK Laras Ashari Setiawan; Nazaruddin Nasution; Abdul Halim Daulay
EINSTEIN (e-Journal) Vol 10, No 1 (2022): EINSTEIN (e-Journal)
Publisher : Universitas Negeri Medan

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (329.594 KB) | DOI: 10.24114/einstein.v10i1.31413

Abstract

Telah dilakukan penelitian yang bertujuan untuk mengetahui jenis batuan bawah permukaan Desa Tuntungan II dan struktur lapisan bedrock bawah permukaan Desa Tuntungan II. Penelitian dilakukan di Desa Tuntungan II, Kecamatan Pancur Batu, Kabupaten Deli Serdang, Provinsi Sumatera Utara. Pengambilan data dilakukan pada tiga lintasan dengan panjang bentangan 200 m menggunakan metode geolistrik resistivitas konfigurasi Schlumberger. Pengolahan data menggunakan software IPI2WIN+IP. Pembuatan model 2D menggunakan software Corel Draw dan Photoshop. Pada daerah penelitian di desa Tuntungan II, Kecamatan Pancur Batu, Kabupaten Deli Serdang, ditemukan jenis batuan bawah permukaan seperti batupasir, andesit, lempung, pasir, dan tufa. Lalu ditemukan juga lapisan bedrock jenis andesit dengan nilai resistivitas sebesar 387 – 480 Ωm dengan kedalaman 1 – 2,40 m dan pendirian bangunan yang direkomendasikan untuk daerah tersebut ialah bangunan berlantai 1 hingga lantai 2.Kata Kunci: Bedrock, Geolistrik, dan Schlumberger
IDENTIFIKASI STRUKTUR LAPISAN BAWAH PERMUKAAN SEBAGAI KAJIAN AWAL DALAM PERENCANAAN PEMBANGUNAN GEDUNG BERTINGKAT DENGAN MENGGUNAKAN METODE GEOLISTRIK Nazaruddin Nasution; Laras Ashari Setiawan
EINSTEIN (e-Journal) Vol 10, No 1 (2022): EINSTEIN (e-Journal)
Publisher : Universitas Negeri Medan

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (453.294 KB) | DOI: 10.24114/einstein.v10i1.33070

Abstract

Telah dilakukan penelitian untuk identifikasi struktur lapisan bawah permukaan sebagai kajian awal dalam perencanaan pembangunan Gedung bertingkat dengan menggunakan metode geolistrik. Metode geolistrik resistivitas dilakukan dengan menginjeksikan arus listrik ke dalam bumi dengan dua elektroda arus dan dua elektroda potensial. Panjang lintasan pada penelitian ini adalah sebanyak 5 titik dengan panjang bentangan terdekat (AB/2) adalah 1,5 m dan bentangan terjauhnya adalah (AB/2) adalah 150 m, kemudian melakukan pengukuran sehingga diperoleh data beda potensial dan kuat arusnya. Data tersebut kemudian diolah menggunakan software IPI2WIN+IP untuk mengetahui litologi bawah permukaan Desa Tuntungan II dan untuk struktur lapisan keras yang terdapat di bawah permukaan Desa Tuntungan II berdasarkan survei geolistrik resistivitas konfigurasi schlumberger. Berdasarkan hasil interpretasi data penelitian diperoleh bahwa Litologi bawah permukaan Desa Tuntungan II pada setiap lintasan pengukuran yaitu terdiri dari batupasir, batu lumpur, andesit, lempung, pasir dan tufa. Jenis batuan bawah permukaan yang ditemukan ialah batupasir, andesit, lempung, pasir, dan tufa. Struktur lapisan keras Desa Tuntungan II berada pada batuan andesit yaitu pada kedalaman 1,54 m - 2,44 m dengan nilai resistivitas 395 Ωm – 520 Ωm. Bangunan yang direkomendasikan adalah bangunan lantai 2