Claim Missing Document
Check
Articles

Found 2 Documents
Search
Journal : Proceeding of World Conference

Development of Technical Drawing Module Based On Projection and Sectional Views Equipped with Lego Block Assembly Media Assistance Agung Prijo Budijono; Wahyu Dwi Kurniawan; Arda Widyatama
Journal of World Conference (JWC) Vol. 1 No. 1 (2019): March 2019
Publisher : NAROTAMA UNIVERSITY, Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (403.205 KB) | DOI: 10.29138/prd.v1i1.97

Abstract

. This research is motivated by the lack of practical learning media in the discussion of projections and pieces in the learning process of technical drawing courses. Referring to the discussion, the researcher made a module "Teaching Drawing Technique Module Main Subjects of Projection and Pieces Equipped with Information Technology Lego Viewer Media Assistance" which later will be a support in the learning process so as to help students individually achieve learning goals in a learning process. Learning media that will be applied in engineering drawing courses, will later be developed using the 4-D development model (four D models) which consists of 4 stages, namely: (1) Define, (2) Design, (3) Development , and (4) Disseminate. The defining stage includes the initial analysis, student analysis, concept analysis, task analysis, and specification of learning objectives. The design phase consists of the preparation of tests, media selection, format selection, and initial design (initial design). At the development stage it consists of module validation by expert lecturers, student response questionnaires, and about the pretest posttest for students. Whereas the deployment is not carried out due to the limited time of the study. The results showed (1) the module products developed were very feasible to use (2) students showed a positive response to the module developed (3) student learning outcomes improved with good categories.
Analysis of Energy Management of Garnesa Electric Car Based Numerical Simulation Modeling Bidya Nur Habib; Agung Prijo Budijono
Journal of World Conference (JWC) Vol. 1 No. 1 (2019): March 2019
Publisher : NAROTAMA UNIVERSITY, Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (707.798 KB) | DOI: 10.29138/prd.v1i1.98

Abstract

Designing an electric car to compete with ESCC should be guided by Vehicle Construction and Stability. One of the areas to consider when designing at the research and development stage is the Mechanical Mechanical System (Rotational Mechanical System). These systems include, wheels, transmissions (gear connections), electric motor rotors and shafts. The purpose of this study was to determine the effect of vehicle energy management on driver driving strategies during the ESCC competition. This is based on Wheel Mechanical System modeling, Dynamic System Analysis and Free Body Diagram. The method used is based on Numerical Simulation. The data parameters used are based on independent variables and control variables. The independent variable of this study is the angular velocity (V?), linear velocity (v) of the vehicle, friction coefficient value (B), shaft stiffness (K), wheel diameter, gear diameter, wheel mass and moment inertia of the wheel. Control variables is technical regulation of ESCC Urban Concept. This Numerical Simulation Test is to determine the required electrical power, travel time and distance of the vehicle. The results showed that the energy needed by GARNESA electric car with an average speed selection of 9.42 m /s based on a maximum speed of 10.15 m /s and a minimum speed of 8.70 m /s requires the amount of power 248.15 Watt. Travel time is 180 seconds in one lap. The distance obtained is 1357 m. Driving strategy based on average speed of 9.42 m /s consumes less power and the distance obtained will be more far.
Co-Authors Achmad Harish Aviansyah Achmad Rianto Achmat Soleh Adhitya Wira Dharma Adly Fitra Ainurroji Agam Seftian Effendi Ahmad Hafizh Ainur Rasy Ahmad Setyo Purnomo Aisyah Nur Khalifah Aisyah Nur Khalifah Aldiansyah Rusminanda Alfian Dwi Cahyo Alfian Reynaldi ALI MASUM, AHMAD Amalia Forma Alfianti Andika Bayu Putro Andrianto, Afan Andriyanti Achsan Anita Wahyuningtias Arda Widyatama Arda Widyatama Arif Saputra ARIFFAIUDDIN, SAMSUL Asrul Ludin Awang Firmansyah Bagus Dwi Pratama Bangkit Krisna Surya Handaru Bidya Nur Habib Bimo Bintang Priantoro Choirul Hamzah Deo Farma Alhadi Desy Syfa Urrohma DIMA DISTYA, YOSHA Djoko Suwito Dwi Safitri Dzulkifl Dzulkifl Fajar Septiawan Dwi Anggoro Fajar Septiawan Dwi Anggoro Haikal Fikri Abdi Rachman Hapsari Peni Agustin Tjahyaningtijas Hima Nurwidya Timur Hizar Alhifari Ramadhan I Wayan Valentino Eka Putra Ibrohim Ibrohim Irenta Teguh Wahyu Widodo Irfan Burhanudin Wibowo Irfan Malik Hartanto Juwono Ardiansah Khoirul Huda Lely Farima Made Pramono MARDHANIS SAIYA, VALANTINO Marwanto, Dodik Maulana Ridhwan Mochammad Takbirul Id’ha Mohamad Rizqi Ardiansyah Muchamad Arif Al Ardha Mugi Prasetyoso, Dwi Muhammad Ichsan Khofi Muhammad Irfan Maulana Muhammad Rifandiansyah Muhammad Sefriza Toriq Hidayat Muhammad Sefriza Toriq Hidayat Muhimatul Ulya Mukasafah NIken Purwidiani Niken Sari Kiss Arimbi Nikes Sari Kiss Arimbi Nur Aini Susanti NUR HABIB, BIDYA PRIYO WIDHIKDHO, ADE Rahayu, Imami Arum Tri RAHMATULLOH, FAQIHUDDIN RAMADAN, RIZKY Raniya Nur Ningsih Redy Ardiansyah Reza Salfani Rio Antoni Rizky Kurniawan Roby Ferdian Ryan Effendi Saiful Anwar Sha’id Khana’fi Soeryanto Soeryanto Soeryanto Soeryanto Susi Tri Umaroh SYAHRONI, MOCH.ERWIN SYAHRUL SYAH, SYEIHAN Syeihan Syahrul Syah Syukri Ainun Alfath Teguh Ardiyanto, Muhammad Teguh Budi Riono Wahyu Dwi Kurniawan Wahyu Dwi Kurniawan Wahyu Dwi Kurniawan WIDYATAMA, ARDA Windy Saputro, Wicaksono Yan Dwi Pratama Yan Dwi Pratama Yosha Dima Distya Yusuf Mochammad Saputra Zuhfrianto, Ali