cover
Contact Name
-
Contact Email
-
Phone
-
Journal Mail Official
ijred@live.undip.ac.id
Editorial Address
Jl. Imam Bardjo, No 4 Semarang 50241 INDONESIA
Location
Kota semarang,
Jawa tengah
INDONESIA
International Journal of Renewable Energy Development
Published by Universitas Diponegoro
ISSN : 22524940     EISSN : 27164519     DOI : https://doi.org/10.14710/ijred
Core Subject : Science,
The scope of journal encompasses: Photovoltaic technology, Solar thermal applications, Biomass, Wind energy technology, Material science and technology, Low energy Architecture, Geothermal energy, Wave and Tidal energy, Hydro power, Hydrogen Production Technology, Energy Policy, Socio-economic on energy, Energy efficiency and management The journal was first introduced in February 2012 and regularly published online three times a year (February, July, October).
Articles 573 Documents
Steam gasification of wood biomass in a fluidized biocatalytic system bed gasifier: A model development and validation using experiment and Boubaker Polynomials Expansion Scheme BPES Vecchione, Luigi; Moneti, Marta; Di Carlo, Andrea; Savuto, Elisa; Pallozzi, Vanessa; Carlini, Maurizio; Boubaker, Karem; Longo, Leonardo; Colantoni, Andrea
International Journal of Renewable Energy Development Vol 4, No 2 (2015): July 2015
Publisher : Center of Biomass & Renewable Energy, Diponegoro University

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.14710/ijred.4.2.143-152

Abstract

One of the most important issues in biomass biocatalytic gasification is the correct prediction of gasification products, with particular attention to the Topping Atmosphere Residues (TARs). In this work, performedwithin the European 7FP UNIfHY project, we develops and validate experimentally a model which is able of predicting the outputs,including TARs, of a steam-fluidized bed biomass gasifier. Pine wood was chosen as biomass feedstock: the products obtained in pyrolysis tests are the relevant model input. Hydrodynamics and chemical properties of the reacting system are considered: the hydrodynamic approach is based on the two phase theory of fluidization, meanwhile the chemical model is based on the kinetic equations for the heterogeneous and homogenous reactions. The derived differentials equations for the gasifier at steady state were implemented MATLAB. Solution was consecutively carried out using the Boubaker Polynomials Expansion Scheme by varying steam/biomass ratio (0.5-1) and operating temperature (750-850°C).The comparison between models and experimental results showed that the model is able of predicting gas mole fractions and production rate including most of the representative TARs compounds
Numerical Study of Effect of Blade Twist Modifications on the Aerodynamic Performance of Wind Turbine Beabpimai, Wiroj; Chitsomboon, Tawit
International Journal of Renewable Energy Development Vol 8, No 3 (2019): October 2019
Publisher : Center of Biomass & Renewable Energy, Diponegoro University

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.14710/ijred.8.3.285-292

Abstract

This paper aims to investigate aerodynamic performance of a wind turbine blade with twist modifications using computational fluid dynamics (CFD). The phenomenon of 3D stall-delay effect in relation to blade twist is the key feature to be investigated in order to improve efficiency of a wind turbine. The NREL (National Renewable Energy Laboratory) Phase VI wind turbine rotor was used for validation and as the baseline rotor. The baseline blade geometry was modified by increasing/decreasing the twist angles in the inboard, mid-board and outboard regions of the blade in the form of a symmetrical curve with maximum twist angle of 3°. The steady incompressible Reynolds-averaged Navier-Stokes (RANS) equations with the k-ω Shear Stress Transport (SST) turbulence closure model were used for the calculations at wind speeds ranging from 5-20 m/s. The computational results for the baseline Phase VI rotor were validated against experimental data and a good agreement was found. The computational results for the modified blades were compared against those of the baseline blade. It was found that increase of annual energy production of up to 5.1% could be achieved by this modification technique.  ©2019. CBIORE-IJRED. All rights reserved
Effect of the Dust on the Performance of Solar Water Collectors in Iraq Ahmed, Omer Khalil
International Journal of Renewable Energy Development Vol 5, No 1 (2016): February 2016
Publisher : Center of Biomass & Renewable Energy, Diponegoro University

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.14710/ijred.5.1.65-72

Abstract

There is little research about it in present literatures in Iraq. So the effect of dust accumulation on the performance of conventional of solar collectors is analyzed. The experimental study was carried out mainly on a flat solar collector, which comprised the major part of this work. According to the experimental results obtained, there is a limited decrease in the instantaneous efficiency which was 1.6 % for the dirty collector. At load condition, the outlet temperature reaches a maximum value of 43.85oC at 12 noon without dust on the front glass and 33.7 oC in the presence of the dust. The instantaneous efficiency reaches its maximum value of 49.74 % at 12 noon without dust and 48.94% with dust after that the efficiency was decreased. The variation of useful transferred energy closely follows the variation of solar intensity and reaches its maximum value of 690 W/m2 at 12 noon in the presence of the dust for this particular day. It is also observed that, at the second half of the day, there is a large decrease in the instantaneous efficiency resulting from a large reduction in the useful energy transferred. Therefore, for Iraqi places, daily cleaning of the glass covers is strictly recommended as part of the maintenance works but the equipment should be cleaned immediately after a dust storm to keep the collector efficient. Article History: Received August 16, 2015; Received in revised form Nov 17, 2015; Accepted Dec 19, 2015; Available onlineHow to Cite This Article: Ahmed, O.K (2016). Effect of the Dust on the Performance of Solar Water Collectors in Iraq. Int. Journal of Renewable Energy Development, 5(1), 65-72.http://dx.doi.org/10.14710/ijred.5.1.65-72 
Ultrasound Assisted Esterification of Rubber Seed Oil for Biodiesel Production Widayat, Widayat; Fajar Tamtomo Kiono, Berkah
International Journal of Renewable Energy Development Vol 1, No 1 (2012): February 2012
Publisher : Center of Biomass & Renewable Energy, Diponegoro University

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.14710/ijred.1.1.1-5

Abstract

Production of biodiesel is currently shifting from the first to the second generation inwhich the raw materials are mostly from non-edible type oils and fats. Biodiesel production iscommonly conducted under batch operation using mechanical agitation to accelerate masstransfers. The main drawback of oil esterification is the high content of free fatty acids (FFA) whichmay reduce the yield of biodiesel and prolong the production time (2-5 hours). Ultrasonificationhas been used in many applications such as component extraction due to its ability to producecavitation under certain frequency. This research is aimed to facilitate ultrasound system forimproving biodiesel production process particularly rubber seed oil. An ultrasound unit was usedunder constant temperature (40oC) and frequency of 40 Hz. The result showed that ultrasound canreduces the processing time and increases the biodiesel yield significantly. A model to describecorrelation of yield and its independent variables is yield (Y) = 43,4894 – 0,6926 X1 + 1,1807 X2 –7,1042 X3 + 2,6451 X1X2 – 1,6557 X1X3 + 5,7586 X2X3 - 10,5145 X1X2X3, where X1 is mesh sizes, X2ratio oil: methanol and X3 type of catalyst.
Tax Incentive Policy for Geothermal Development: A Comparative Analysis in ASEAN Abidin, Mohammad Zainul; Rosdiana, Haula; Salomo, Roy Valiant
International Journal of Renewable Energy Development Vol 9, No 1 (2020): February 2020
Publisher : Center of Biomass & Renewable Energy, Diponegoro University

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.14710/ijred.9.1.53-62

Abstract

This paper examines tax incentive policies in geothermal industries in ASEAN to better understand the development of geothermal industry investment in the ASEAN Member States (AMS) using a qualitative method. The results indicate that tax incentive policies have supported the investment climate and the development of geothermal industries in the AMS. Geothermal investments and production capacities in AMS have increased significantly. AMS that provide geothermal tax incentives include Indonesia, Lao PDR, the Philippines, Thailand and Vietnam. The performance of geothermal tax incentive policies is reflected in the level of utilization of geothermal potential, which is higher in states that provide greater tax incentives. The results also indicate that geothermal power plants in AMS use dry steam, flash and binary cycle technologies with flash plants being the most common. Results suggest that the future development of geothermal energy in AMS will be related to the tax incentive policy and investment climate in those states. Furthermore, the granting of various types of tax incentives should be focused on the initial investment in geothermal development. ©2020. CBIORE-IJRED. All rights reserved
Subsurface Structure and Fluid Flow Analysis Using Geophysical Methods in the Geothermal Manifestation Area of Paguyangan, Brebes, Central Java Setyawan, Agus; Triahadini, Agnis; Yuliananto, Yayan; Aribowo, Yoga; Widiarso, Dian Agus
International Journal of Renewable Energy Development Vol 5, No 3 (2016): October 2016
Publisher : Center of Biomass & Renewable Energy, Diponegoro University

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.14710/ijred.5.3.171-177

Abstract

The indication of an active geothermal system is shown by the presence of surface manifestations such as the hot spring in Kedungoleng, Paguyangan, Brebes, Central Java. The temperature of the largest hot spring reaches 74o C and there is an assumption that this is an outflow of Mount Slamet geothermal system. DC-resistivity, Spontaneous Potential (SP) and Shallow Surface Temperature surveys were conducted to determine the subsurface structure as well as its correlation with the distribution of thermal fluid flow and shallow surface temperature. The subsurface resistivity has been investigated using 5 points of the Schlumberger configuration with 400 m separation for each point. For the fluid and temperature pattern, a measurement using 15 m interval in 3 lines of conducting fixed electrode configuration has been carried out, along with a 75 cm of depth of temperature measurement around the manifestation area. The thermal fluid is assumed by the low resistivity of 0.756 to 6.91Ωm and this indicates sandstone that has permeable characteristic. The fluid flows in two layers of Sandstone at more than 10 meter from surface of the first layer. Accordingly, the SP values have a range between -11- 11 mV and a depth interval of 13.42- 28.75 m and the distribution of temperature is between 24o-70oC at a tilting range of 46.06o-12.60o. Hence it can be inferred that the thermal fluid moves in the Northwest direction and is controlled by a fault structure stretching from Northwest to Southeast.Article History: Received Feb 3, 2016; Received in revised form July 11, 2016; Accepted August 13, 2016; Available onlineHow to Cite This Article: Setyawan, A., Triahadini, A., Yuliananto, Y., Aribowo, Y., and Widiarso, D.A. (2016) Subsurface Structure and Fluid Flow Analyses Using Geophysical Methods in Geothermal Manifestation Area of Paguyangan, Brebes, Central Java. Int. Journal of Renewable Energy Development, 5(3), 171-177.http://dx.doi.org/10.14710/ijred.5.3.171-177
Development of Formaldehyde Adsorption using Modified Activated Carbon – A Review Rengga, W.D.P; Sudibandriyo, M.; Nasikin, M
International Journal of Renewable Energy Development Vol 1, No 3 (2012): October 2012
Publisher : Center of Biomass & Renewable Energy, Diponegoro University

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.14710/ijred.1.3.75-80

Abstract

Gas storage is a technology developed with an adsorptive storage method, in which gases are stored as adsorbed components on the certain adsorbent. Formaldehyde is one of the major indoor gaseous pollutants. Depending on its concentration, formaldehyde may cause minor disorder symptoms to a serious injury. Some of the successful applications of technology for the removal of formaldehyde have been reported. However, this paper presents an overview of several studies on the elimination of formaldehyde that has been done by adsorption method because of its simplicity. The adsorption method does not require high energy and the adsorbent used can be obtained from inexpensive materials. Most researchers used activated carbon as an adsorbent for removal of formaldehyde because of its high adsorption capacity. Activated carbons can be produced from many materials such as coals, woods, or agricultural waste. Some of them were prepared by specific activation methods to improve the surface area. Some researchers also used modified activated carbon by adding specific additive to improve its performance in attracting formaldehyde molecules. Proposed modification methods on activation and additive impregnated carbon are thus discussed in this paper for future development and improvement of formaldehyde adsorption on activated carbon. Specifically, a waste agricultural product is chosen for activated carbon raw material because it is renewable and gives an added value to the materials. The study indicates that the performance of the adsorption of formaldehyde might be improved by using modified activated carbon. Bamboo seems to be the most appropriate raw materials to produce activated carbon combined with applying chemical activation method and addition of metal oxidative catalysts such as Cu or Ag in nano size particles. Bamboo activated carbon can be developed in addition to the capture of formaldehyde as well as the storage of adsorptive hydrogen gas that supports renewable energy. Keywords: adsorption; bamboo; formaldehyde; modified activated carbon; nano size particles
Optimizing the Synthesis of Lignin Derivatives from Acacia mangium to Improve the Enzymatic Hydrolysis of Kraft Pulp Sorghum Bagasse Fatriasari, Widya; Hamzah, Fajar Nur; Pratomo, Bagas Ikhasan; Fajriutami, Triyani; Ermawar, Riksfardini Annisa; Falah, Faizatul; Laksana, Raden Permana Budi; Ghozali, Muhammad; Iswanto, Apri Heri; Hermiati, Euis; Winarni, Ina
International Journal of Renewable Energy Development Vol 9, No 2 (2020): July 2020
Publisher : Center of Biomass & Renewable Energy, Diponegoro University

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.14710/ijred.9.2.227-235

Abstract

The present study is aimed at optimizing the synthesis of Amphipilic lignin derivatives (A-LD) from the isolated lignin of A.mangium black liquor (BL), using the one and two step acid isolation method, and commercial lignin (LS) was used as comparison. The experimental design was conducted using Taguchi method, which consisted of four parameters and two level factors, with reference to the matrix orthogonal array, L8, including temperature, reaction time, amount of polyethylene glycol diglycidylethers (PEGDE) and Kraft lignin (KL). Furthermore, the kraft pulp of sweet sorghum bagasse (SSB) was used as substrate in the enzymatic hydrolysis (NREL method), with addition of A-LD, whose functional group and surface tension were then characterised using ATR-FTIR and surface tension equipment. Conversely, an improvement in the reducing sugar yield (RSY) compared to the control was observed after adding various A-LDs to the substrate during enzymatic hydrolysis. This product was more prospective for L2S than others products under milder circumstances, due to the fact that it possesses the lowest surface tension. Also, Taguchi analysis demonstrated the treatment at 60 °C for 1 h with 3.0 g and 1.0 g of PEDGE and lignin, respectively as the optimum condition, while the amount of lignin present was included as a factor with the propensity to significantly affect A-LD L1S and LS. Therefore, it was established that the A-LDs from A. mangium kraft lignin require milder synthesis conditions, compared to other existing methods and despite the differences in optimum experimental condition for L2S and LS, the functional groups in the IR spectra possessed very identical characteristics. 
Electricity from Wind for Off-Grid Applications in Bangladesh: A Techno-Economic Assessment Rahman, Md. Mustafizur; Baky, Md Abdullah Hil; Islam, A.K.M. Sadrul
International Journal of Renewable Energy Development Vol 6, No 1 (2017): February 2017
Publisher : Center of Biomass & Renewable Energy, Diponegoro University

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.14710/ijred.6.1.55-64

Abstract

Global GHG (greenhouse gas) emissions are increasing substantially and electricity sector is one of the key contributors to the world’s total GHG emissions. GHG emissions cause ozone layer depletion and global warming. Different policy regulation agencies are adopting regulations to reduce GHG emissions in various sectors. People already have started power generation from cleaner sources. Renewable energy sources can provide cleaner electricity. Bangladesh is a densely populated country and most of the country’s electricity is produced from natural gas and coal. The Bangladesh government has set a goal to utilize renewable energy for the production of 10% of its electricity by the year 2020. Bangladesh has a lot of isolated coastal areas which are not connected to the national grid which can be electrified by using abundant wind energy. In this study a techno-economic analysis has been conducted for an off-grid island of Bangladesh. The analysis was conducted by developing a data intensive model that calculates the generation cost of electricity from wind energy. The model also estimates the capital cost of the system. The model shows that electricity can be produced from wind energy at a cost of $0.57/kWh. The system’s capital cost was calculated to be $63,550.16.Article History: Received October 15th 2016; Received in revised form January 26th 2017; Accepted February 4th 2017; Available onlineHow to Cite This Article: Rahman, M.M., Baky, M.A.H, and Islam, A.K.M.S. (2017) Electricity from Wind for Off-Grid Applications in Bangladesh: A Techno-Economic Assessment. International Journal of Renewable Energy Develeopment, 6(1), 55-64.http://dx.doi.org/10.14710/ijred.6.1.55-64
Enhancement of Energy Efficiency and Food Product Quality Using Adsorption Dryer with Zeolite Djaeni, Moh; Sasongko, S.B.; van Boxtel, A.J.B.
International Journal of Renewable Energy Development Vol 2, No 2 (2013): July 2013
Publisher : Center of Biomass & Renewable Energy, Diponegoro University

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.14710/ijred.2.2.81-86

Abstract

Drying is a basic operation in wood, food, pharmaceutical and chemical industry. Currently, several drying methods are often not efficient in terms of energy consumption (energy efficiency of 20-60%) and have an impact on product quality degradation due to the introduction of operational temperature upper 80oC. This work discusses the development of adsorption drying with zeolite to improve the energy efficiency as well as product quality. In this process, air as drying medium is dehumidified by zeolite. As a result humidity of air can be reduced up to 0.1 ppm. So, for heat sensitive products, the drying process can be performed in low or medium temperature with high driving force. The study has been conducted in three steps: designing the dryer, performing laboratory scale equipment (tray, spray, and fluidised bed dryers with zeolite), and evaluating the dryer performance based on energy efficiency and product quality. Results showed that the energy efficiency of drying process is 15-20% higher than that of conventional dryer. In additon, the dryer can speed up drying time as well as retaining product quality.