cover
Contact Name
Irza Sukmana
Contact Email
irza.sukmana@eng.unila.ac.id
Phone
+62721234234
Journal Mail Official
jesr@eng.unila.ac.id
Editorial Address
Faculty of Engineering, Universitas Lampung. Jl. Soemantri Brojonegoro No.1 Bandar Lampung – Indonesia. http://eng.unila.ac.id
Location
Kota bandar lampung,
Lampung
INDONESIA
Journal of Engineering and Scientific Research (JESR)
Published by Universitas Lampung
ISSN : 26850338     EISSN : 26851695     DOI : https://doi.org/10.23960/jesr.v4i1.78
The focus and scopes of JESR is on but not limited to Mechanical Engineering and Material Sciences, Chemical and Environmental, Industrial and Manufacturing Engineering, Computer and Information Technology, Electrical and Telecommunication, Civil and Geodetic Engineering, Architecture and Urban Planning, Geophysical Science and Engineering, and other multidisciplinary research. The main criteria for publication are including the originality, scientific quality and interest to the aim and focus. JESR publishes twice a year for June and December editions. We welcome for publication collaborations with organizer of International Seminars, Conferences and Symposiums around the world. We are encouraging authors to submit their manuscript through our online system.
Articles 130 Documents
The Development Of Multi-Path Adversary Analysis Tool For Vulnerability Assessment of Physical Protection Systems (MAVA) D Andiwijayakusuma; A Mardhi; T Setiadipura; A Purqon; Z Suud
Journal of Engineering and Scientific Research Vol. 3 No. 2 (2021)
Publisher : Faculty of Engineering, Universitas Lampung Jl. Soemantri Brojonegoro No.1 Bandar Lampung, Indonesia 35141

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1004.215 KB) | DOI: 10.23960/jesr.v3i2.92

Abstract

Abstract. The Physical Protection System (PPS) is an important component in each nuclear facility security aspect. We must regularly evaluate the effectiveness of PPS to ensure the system can anticipate every enemy attack; therefore, a PPS vulnerability assessment is needed. In this study, we develop a Multi-path Analysis tool for Vulnerability Assessment of PPS (MAVA) based on the Adversary Sequence Diagram (ASD) implemented in python computer code. We examined for feasibility by applying the code to a hypothetical facility (National Nuclear Research Facility - NNRF). The results of calculations compared to single-path analysis (EASI) show the advantages of MAVA, which can calculate the probability of interruption simultaneously on multi-path analysis. MAVA also predict the adversary's most vulnerable paths (MVP) with its various strategies for intrusion path. MAVA results show that multi-path calculations help analysts obtain information faster in evaluating to improve the effectiveness of PPS.
The Design and Build a Children's Temperature Monitoring System Using The MLX90614 Temperature Sensor and NODEMCU ESP-12E Based On Android Zidny Sholehan Abdullah
Journal of Engineering and Scientific Research Vol. 4 No. 1 (2022)
Publisher : Faculty of Engineering, Universitas Lampung Jl. Soemantri Brojonegoro No.1 Bandar Lampung, Indonesia 35141

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (381.657 KB) | DOI: 10.23960/jesr.v4i1.67

Abstract

The degree of children's health reflects the nation's health status, because children as the nation's next generation have abilities that can be developed in continuing the nation's development. The limited parental monitoring of children, so the authors make a child temperature monitoring device that can make it easier for parents to monitor their child's temperature in real time. This study uses a sensor temperature of the infrared MLX90614, NodeMCU ESP-12E as a controller programmed with the Arduino software idea later in the show via the LCD and the application blynk. This system was developed based on the needs of the children's monitoring system. The results of this research are that a child temperature monitoring system has been realized that can monitor the condition of a child's body in real time. Metode used isto compare data between Thermometer Gun with sensor systems ML X90614, then obtained an average difference of 0.0190 C and an average error of 0.053%. Keywords: Infrared sensor, MLX90614, real time, monitoring
Correlation of BMKG with TRMM for daily and monthly rainfall series in Banten region Ahmad Zakaria; Sumiharni Sumiharni
Journal of Engineering and Scientific Research Vol. 4 No. 1 (2022)
Publisher : Faculty of Engineering, Universitas Lampung Jl. Soemantri Brojonegoro No.1 Bandar Lampung, Indonesia 35141

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1413.154 KB) | DOI: 10.23960/jesr.v4i1.78

Abstract

Daily and monthly rainfall data series are necessary data for planning purposes in Civil Engineering and other fields. Incomplete rainfall data often occurs, so that rainfall data must be estimated based on rainfall data from several other nearby locations. The addition of rainfall data can lead to inaccurate planning. Rainfall data used for planning in the civil engineering sector is usually taken from the BMKG station. This data is taken from the rainfall station above the ground. Besides, that can also produce rainfall data from TRMM. Can take rainfall data from TRMM at all locations according to a coordinate of location. This rainfall data denotes an average rainfall taken from the satellite approximately 250 meters above the ground surface. An equation will be obtained by comparing the daily and monthly rainfall data from the two data sources. Based on TRMM rainfall, we can use the equation to estimate ground rainfall in a location. In this study, daily rainfall, monthly rainfall, the spectrum of daily and monthly rainfall data from BMKG are compared with rainfall and the spectrum of daily and monthly rainfall data from TRMM. The analysis results show that the monthly rainfall data from TRMM and BMKG correlate better than daily rainfall data.
Analysis Characteristics of Passenger in Election of Executive Ship Transportation Mode (Cases Study: Bakau Heni-Merak Port) Atika Ulima Zhafira; Rahayu Sulistyorini; Kristianto Usman
Journal of Engineering and Scientific Research Vol. 4 No. 1 (2022)
Publisher : Faculty of Engineering, Universitas Lampung Jl. Soemantri Brojonegoro No.1 Bandar Lampung, Indonesia 35141

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (834.738 KB) | DOI: 10.23960/jesr.v4i1.96

Abstract

Ferry is one of the strategic water transportations, but Ferry is often not considered important in its development, so research are needed to examine the effect of passenger characteristics on executive ferry transportation. Mode selection is one of the models used in transportation planning, this is due to the key role of public transportation in an effort to improve services from transportation modes. This study was conducted to determine the characteristics and factors that influence passengers in choosing modes. The analysis of the mode selection model in this study uses logistic regression analysis with the help of the SPSS program. The results in the study explain that the factors that influence the choice of mode for executive ferry passengers are Income Level Variables (X5), Transportation to Port Variables (X7) and Ship Schedule Considerations Variables (X10). Results Based on statistical tests, the following logistic regression was obtained: Y = 0.049 + 1.593 X5 + 1.017 X7 + 0.0834 X10
The Initiation Study on the Gold Potential Resources at West Coast Area in Lampung Province, Indonesia Akroma Hidayatika; Suharno; Rahmi Mulyasari; Hesti; Idabagus S Yogi; Arif P Prabowo; Syamsurijal Rasimeng
Journal of Engineering and Scientific Research Vol. 4 No. 1 (2022)
Publisher : Faculty of Engineering, Universitas Lampung Jl. Soemantri Brojonegoro No.1 Bandar Lampung, Indonesia 35141

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (464.216 KB) | DOI: 10.23960/jesr.v4i1.97

Abstract

Gold mineral (Au) is formed due to an increase in the residual solution of magma deposited at high temperature and pressure. This study aims to estimate the potential of gold minerals in the west coast area in Lampung Province. This initiation study was using a geophysical resistivity model. Based on geological data, gold minerals in the West Coast are classified as epithermal hydrothermal deposits in the form of low sulfide quartz veins. The results of the subsurface interpretation were identified as a gold mineralization zone associated with the rock in the form of volcanic rock which has a resistivity value of 400?.m. The source rock volume has been estimated at 130,000 m3 and ?133,000 m3. So that the Au mineral content in the study area is estimated at 0.5-2.09 tons. A future study should be conducted in relation to the development of gold mining industry in Lampung West Coast area, that may integrate more engineering experts.
The Effect of the use of Silica Sand Before and After Physical Activation on Acceleration of 4-Step Gasoline Motorcycle Engine Akhmad Riszal; Sandy Dwi Hardin; Herry Wardono; M. Dyan Susila ES; A. Yudi Eka Risano
Journal of Engineering and Scientific Research Vol. 4 No. 1 (2022)
Publisher : Faculty of Engineering, Universitas Lampung Jl. Soemantri Brojonegoro No.1 Bandar Lampung, Indonesia 35141

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (925.97 KB) | DOI: 10.23960/jesr.v4i1.98

Abstract

This research was conducted with the aim of knowing the Effect of using silica sand before and after physical activation on the acceleration of a 4-stroke gasoline motorcycle engine. This research was conducted by testing the acceleration 0 – 80 km/hour and 40 – 80 km/hour with variations in the composition of tapioca in the pellet mixture (1%, 2%, and 3%) and variations in temperature activation (150?C, 200?). C, and 250?C). The silica sand pellets used in this study were 10 mm in diameter with a thickness of 3 mm, which had been activated for 60 minutes. The results showed that the use of silica sand had an effect on the acceleration of a 4-stroke gasoline motorcycle. The best composition of silica sand pellets occurs in the amount of tapioca 3% and with an activation temperature of 250?C, which can increase the acceleration by 12.45% at an acceleration of 0 – 80 km/hour.
Utilization of Natural Zeolites and Fly Ash (Coal) Mixture Physically Activated Using Furnace As A Pellet - shaped Air Filter To Increase Engine Torque, Tecumseh TD110. 4-Stroke Petrol Motor yudi risano
Journal of Engineering and Scientific Research Vol. 4 No. 1 (2022)
Publisher : Faculty of Engineering, Universitas Lampung Jl. Soemantri Brojonegoro No.1 Bandar Lampung, Indonesia 35141

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (643.119 KB) | DOI: 10.23960/jesr.v4i1.99

Abstract

An air filter made from a mixture of natural zeolite and coal fly ash can be used to remove nitrogen (N2) and moisture (H2O) in the air. This filter can produce oxygen-rich air (O2) flowing into the combustion chamber to increase the quality of the combustion process so that complete combustion occurs and improve engine torque. In this research the filter was made from a physically activated mixture of natural zeolite and fly ash through heating in a furnace for 1 hour with temperature variations (200oC, 250oC, 300oC, 350oC), mass variations (50%, 75%, 100%) and variations in the composition of Z100%:F0%, Z75%:F25%, Z50%:F50%, Z25%:F75%, Z0%:F100%. Tests were carried out using a 4-stroke gasoline engine of Tecumseh TD110 located in the Motor Bakar and Propulsion Laboratory of the Mechanical Engineering Department, University of Lampung. Test results show that the biggest improvement in torque occurs in using a filter composition of Z50%:F50%, namely by 28.41%. The followed filter of the composition of Z75%:F25% is as big as 28.31%. The activation temperature of 350oC can improve the torque by 35.08%.
The effect of filler adding palm kernel shell ash on durability and marshall values properties of asphalt concrete mix Amelia Oktavia; Irza Sukmana; Yanuar Zulardiansyah Arif; Gigih Forda Nama
Journal of Engineering and Scientific Research Vol. 4 No. 1 (2022)
Publisher : Faculty of Engineering, Universitas Lampung Jl. Soemantri Brojonegoro No.1 Bandar Lampung, Indonesia 35141

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1032.007 KB) | DOI: 10.23960/jesr.v4i1.100

Abstract

Lampung  Province is one of the palm oil producers, especially in  Way Kanan Regency. Way Kanan Regency has two palm oil-producing mills, namely  PT.  Sawit  Indo Mas which is located  in Kampung Tanjung  Raja Sakti Blambangan  Umpu  and PT PLP which is located  in Kampung Bumi  Agung, Bahuga District. The two factories duce thousands of tons of Crude Palm Oil (CPO)   vegetable oil daily produced from palm fruit plants (Elaeis Guineensis Jacq, Arecaceae). From oil management, it is undeniable that it can create a lot of solid waste from the palm shell. Meanwhile, the government has not made much effort to use the waste from the waste. When managing palm fruit, palm shells cannot be processed into oil because they have a hard texture, so the shells are discarded and become waste. Then we use the shell for research material as a filler. Palm shell ash has a silicon dioxide  (SiO2) content which is also contained in Portland cement, so this content can allow the acquisition of a good asphalt mixture on the AC-BC layer. This study aims to see the effect of the effectiveness of adding shell ash fillers from palm shell waste in marshall test tests and value the resulting durability. The addition of fillers with percentages of  20%, 30%, 40%, 50%and 60%. From the results obtained from the test results in the laboratory that the addition of shell ash fillers of 40% gets better performance compared to shell ash with percentages of  20%, 30%, and 60%, with a higher state value of 1225 kg shown. In marshall testing, using palm shell ash fillers can increase the value of  KAO. So that from the marshall test, the durability value of the sample immersion at the IRS value of 0%  was 98.4% greater than the 40%, which was  91.13%. Overall, using palm shell ash fillers meets the minimum requirements of Bina Marga as an asphalt mixture. The degree of weather change in immersion durability affects the strength level of the marshall test.
The Effect of Barite Addition and Graphite Particle Size on The Specific Abrasion of Fly-Ash/Phenolic Composite for Brake Lining Application Shirley Savetlana; Zulhanif Zulhanif; Harnowo Supriadi; Irvan Ramadhan; Teten Beliantara
Journal of Engineering and Scientific Research Vol. 4 No. 1 (2022)
Publisher : Faculty of Engineering, Universitas Lampung Jl. Soemantri Brojonegoro No.1 Bandar Lampung, Indonesia 35141

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (888.599 KB) | DOI: 10.23960/jesr.v4i1.102

Abstract

Annually, million tons of fly-ash and bottom fly-ash is a waste of coal power plant. Fly ash contains Iron-oxide, alumina and silica. Those hard particle makes fly-ash can be used as a reinforcement in polymer composite. This composite is a wear resistance material and can be used as material for brake lining application. Fly ash reinforced phenolic composite has a low specific abrasion. The composite for brake lining material consisted of the reinforcement, friction modifier, solid lubricant and filler. Graphite is used as solid lubricant while barite is used as filler. Many research were carried out research on the particle size effect on the composite mechanical properties. However the size different between the constituent in composite has not investigated. Also the optimal barite weight fraction has not being observed. The composite was made by mixing all of the constituent, pressing in the mold and curing. The result show that the graphite particle size ? 150 mm has the lowest specific abrasion. The observation using scanning electron microscope shows that the composite contained small particle of ? 56 mm tends to agglomerate than the composite contained larger particle of ? 150 mm. the composite contained 15% barite has the lowest specific abrasion. The micrograph of scanning electron microscope shows the mixed of phenolic and barite evenly covered the graphite and fly-ash particles.
Domestic Wastewater Disinfection Planning for Constructed Wetland Treatment Effluent Giovanni Ruly Putra; Betanti Ridhosari; Evi Siti Sofiyah; Nurulbaiti Listyendah Zahra; Ariyanti Sarwono; I Wayan Koko Suryawan
Journal of Engineering and Scientific Research Vol. 4 No. 2 (2022)
Publisher : Faculty of Engineering, Universitas Lampung Jl. Soemantri Brojonegoro No.1 Bandar Lampung, Indonesia 35141

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.23960/jesr.v4i2.104

Abstract

Excessive water consumption to meet water needs has changed aquatic water quality and quantity. Focus on domestic wastewater treatment via built wetlands. Disinfection protects humans against disease-causing viruses, bacteria, and protozoan parasites in wastewater. This study planned the disinfection of artificial wetland wastewater to fulfill microbiological criteria. From the examined data, each unit's design criteria and disinfection effectiveness for the created wetland outlet in the WWTP unit will be discussed. The created wetland must process 8696 cfu/100mL of fecal coliform. Despite good processing efficiency, 94% of fecal coliforms do not fulfill quality criteria. WWTP's wetland emits 8.011 mg/L of Ammonia. 90% chlorine costs Rp. 35,000/kg on the market. Total disinfection costs are rough Rp. 1,018,210.73. Water quality, lamp output power, and exposure distance affect lamp intensity. The lamp's electric power controls the beam's intensity; the more power, the more emission. The emitted power isn't equal to the lamp's electric power. According to the state electricity provider, families with a 900VA power limit will pay Rp. 1,352/kWh in July-September 2021. Nine 30-W bulbs irradiate bacteria. The lights will run for 24 hours non-stop. Hence the monthly electricity usage is 194.4 kWh or Rp 262.829.00.

Page 8 of 13 | Total Record : 130