cover
Article Per Year (5 Year)
All
Home Page
OAI Link
Editorial Team
Contact
Reviewer
Google Scholar
Contact Name
Oman Somantri
Contact Email
oman.somantri@pnc.ac.id
Phone
-
Journal Mail Official
infotekmesin@gmail.com
Editorial Address
-
Location
Kab. cilacap,
Jawa tengah
INDONESIA
Infotekmesin
Published by Politeknik Negeri Cilacap
ISSN : INFOTEKMES     EISSN : 26859858     DOI : -
Core Subject : Science, Engineering,
Computer Science & IT Electrical & Electronics Engineering Mechanical Engineering
INFOTEKMESIN is a peer-reviewed open-access journal with e-ISSN 2685-9858 and p-ISSN: 2087-1627 published by Pusat Penelitian dan Pengabdian Masyarakat (P3M) Politeknik Negeri Cilacap. The journal invites scientists and engineers to exchange and disseminate theoretical and practice-oriented in the various topics include, but not limited to Informatics, electrical Engineering, and mechanical Engineering.
Arjuna Subject : -
Articles 669 Documents
 31   32   33   34   35 
Korelasi Nilai Oktan dan Kandungan Oksigen Biofuel Mangrove dengan Brake Torque dan Emisi NOx Mesin Bensin 150cc Syarifudin; Khumaidi Usman, Muhamad; Fatkhurrozak, Faqih; Lukman Sanjaya, Firman
Infotekmesin Vol 16 No 1 (2025): Infotekmesin: Januari 2025
Publisher : P3M Politeknik Negeri Cilacap

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.35970/infotekmesin.v16i1.2565

Abstract

Alternative fuels are a priority to reduce the problem of fuel stock shortages. Bioethanol has potential because of its octane number specifications, oxygen content, and simple production techniques. Mangrove bioethanol is produced from mangrove fruit, which is non-edible and abundant. This study aims to observe the correlation of Mangrove Biofuel specifications (mixture of gasoline and 5% Mangrove Bioethanol) to Brake Torque and NOx Emissions produced by gasoline engines. Experimental methods are applied, from Mangrove Bioethanol production, octane value, oxygen content testing, and Mangrove Biofuel production to performance and emission testing. The results of the study showed that the correlation of the 101 octane number specifications and 30.31% oxygen content of Mangrove Biofuel increased the highest Brake Torque, reaching 5.45%, and increased the highest NOx emissions up to 6.54% at engine speeds of 5000 rpm.
Simulasi Computational Fluid Dynamics (CFD) untuk Optimalisasi Proses Perekatan pada Oven Bambu Laminasi Bahari, Galuh; Septhia Irawati, Inggar; Aris Hendaryanto, Ignatius; Ayu Putri Pratiwi, Ilham; Krisnaputra, Radhian; Sugiyanto; Wijoyo, Joannes Bimo
Infotekmesin Vol 16 No 1 (2025): Infotekmesin: Januari 2025
Publisher : P3M Politeknik Negeri Cilacap

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.35970/infotekmesin.v16i1.2567

Abstract

The utilization of bamboo in architecture and construction as an eco-friendly alternative to wood is steadily increasing. While ovens are crucial tools in the production of laminated bamboo, particularly for heating during the bonding process, research on ovens specifically designed for bamboo lamination remains scarce. This study aims to optimize the design of laminated bamboo ovens using Computational Fluid Dynamics (CFD) simulations to achieve uniform heat distribution and maximize thermal efficiency. Three design iterations were tested: Iteration 1 with an air velocity of 4 m/s, Iteration 2 with 1.5 m/s, and Iteration 3 with 3 m/s. The results revealed that Iteration 1 exhibited uneven heat distribution, with initial temperatures reaching 1175 K before dropping sharply to 800 K. Iteration 2 showed slower initial heating, achieving a final temperature of 360 K, but heat distribution remained suboptimal. Iteration 3 delivered the best performance, achieving uniform and stable heat distribution near the target temperature of 473 K (200 °C). Overall, Iteration 3 demonstrated the most efficient thermal performance, not only meeting the target temperature with consistent heat distribution but also enhancing the overall heating efficiency of the oven.
Analisis Hasil Uji Tarik dan SEM pada Obyek Cetak 3D dari Filamen Limbah Plastik PET Tri Hannanto Saputra; Ariawan, Radhi; Nur Akhlis Sarihidaya Laksana; Unggul Satria Jati; Dikky Kusuma Wijaya
Infotekmesin Vol 16 No 1 (2025): Infotekmesin: Januari 2025
Publisher : P3M Politeknik Negeri Cilacap

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.35970/infotekmesin.v16i1.2577

Abstract

3DPrinting filament from PET plastic bottle waste is one appropriate solution to overcome PET plastic waste. This research aims to develop a PET plastic bottle waste recycling method using extrusion technology into 3DPrinting filament. The filament formed is used in the printing process using a 3DPrinting FDM machine. The printed object specimens were Dogbone ASTMD638 Type V. Previous research used tensile test and macroscopy photography methods to observe the tensile strength. This research used filament-making, tensile test, and SEM test methods. This research showed that PET plastic bottle waste can be recycled into 3DPrinting filaments. Based on the tensile test result, the average maximum tensile stress from lowest to highest in the sequence was 7.4 MPa, 12.4 MPa, and 14.9 MPa. The type of fracture that occurred in the specimen with the highest maximum tensile strength was a brittle fracture.
Analisa Pengukuran Ketebalan Steel Block, Aluminium Block dan Steel Plate Menggunakan Ultrasonic Thickness Gauge Ulikaryani, Ulikaryani; Unggul Satria Jati; Radhi Ariawan; Dian Prabowo; Sabtun Ismi Khasanah; Hamid Abdillah
Infotekmesin Vol 16 No 1 (2025): Infotekmesin: Januari 2025
Publisher : P3M Politeknik Negeri Cilacap

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.35970/infotekmesin.v16i1.2583

Abstract

Thickness measurement using an ultrasonic sensor is a type of non-destructive test (NDT) that is commonly used in various industries. Measurement of thickness (thickness) on steel blocks, aluminum blocks and steel plates using an ultrasonic thickness gauge. The method used is the contact testing method which is then compared with manual measurements. Based on data analysis from the measurement results, it was found that the thickness with the highest percent error was in the Steel S3 sample, namely 93.87%. Meanwhile, the thickness measurement with the lowest percent error in the Steel plate sample was 0%. Meanwhile, for measuring the dimensions of artificial corrosion defects, the smallest error percentage obtained was 0% for several dimensions, with the average measurement error obtained being 22.82%. The profile shape of the detected artificial corrosion defects is exactly the same as the reference profile. So, measuring the thickness of steel blocks, aluminum blocks and steel plates as well as measuring artificial corrosion defects located in steel plates can be detected well and the measuring results can be trusted.
Analisis Intensitas Turbulensi Terhadap Kestabilan Kecepatan Angin Test Section pada Struktur Wind Tunnel Arif Pratama, Riza; Ikhsan, Muhammad; Wicaksono, Dhimas; Rieza, M. Safiq; Zainal Abidin , Munir
Infotekmesin Vol 16 No 1 (2025): Infotekmesin: Januari 2025
Publisher : P3M Politeknik Negeri Cilacap

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.35970/infotekmesin.v16i1.2511

Abstract

Wind tunnels in aerodynamic testing always have very large sizes to avoid high turbulence intensity. Turbulence intensity analysis is used to determine the size of a smaller wind tunnel to be more efficient in limited space. The use of epoxy fiber resin material is because lighter than aluminum with a thickness of 5mm. The purpose of the study was to produce a wind tunnel with a small size with low turbulence intensity and minimize large manufacture costs. The method used is constructive to analyze the wind tunnel design in determining the maximum wind flow speed at test section does not exceed the turbulence intensity limit. The results of the analysis showed that the wind tunnel structure design has the ability to receive an inlet wind flow of 5 m / s with a maximum wind flow speed at the test location of 10.7 m / s. The wind tunnel design cannot exceed the maximum wind flow speed at the test section because it will produce turbulence intensity above 5% which affects the test result.
Rancang Bangun Mesin Hot Press Hidrolik 10 Ton Untuk Cetakan Spesimen Bahan Uji Komposit Fiberglass jenal, Jenal Sodikin; Ariawan, Radhi; Ardiansyah Pradana, Rizky Nur; Dwi Cahyo, Rizal Agung
Infotekmesin Vol 16 No 1 (2025): Infotekmesin: Januari 2025
Publisher : P3M Politeknik Negeri Cilacap

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.35970/infotekmesin.v16i1.2521

Abstract

Hydraulic Press Machines are also called composite molding machines, 10 ton hot hydraulic press machines are used to print fiberglass composite test material specimens, made to press FRP material into a certain shape so that it is easy to carry out further testing. In order to print test specimens for fiberglass composite test materials, the research aims to design, carry out calculations, and carry out function test of the machine. A hydraulic pressure of 10 tons was chosen to test the specimen whether at the specified maximum pressure the material could survive after further testing. The VDI 2222 engineering approach is used in machine design. Solidworks 2020 is used to get the design shape. With a compression force capacity of 10 tons, the pressure system design produces dimensions of 600 x 100 x 700 mm. consists of several parts such as a pressure gauge with a capacity of 20 tons, a set of temperature sensors, a timer, a sliding shaft, a 20 mm linear bearing, a 24 volt DC wiper motor, a 10 ton hydraulic jack, and a crank system as a transmission. Based on the test results, the pressure gauge can read the pressure produced by the jack, the temperature sensor can read the heat used, namely 110˚C, and the wiper motor can operate up to a maximum pressure of 3 tons. The pressure system can function effectively if a manual pressure of 10 tons is applied. Tests show that using a temperature of 100˚C for 10 minutes gives the best results.
Uji Performa Sistem Hidrolik Alat Peraga Mini Excavator Zhugimada Nur Esa, Suhada; Prihadianto, Braam Delfian; Anggoro Hasan, Dani; Ardean Kurnianto Prayitno, Yosephus; Septian, Miko; Nurul Hidayat, Anisa
Infotekmesin Vol 16 No 1 (2025): Infotekmesin: Januari 2025
Publisher : P3M Politeknik Negeri Cilacap

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.35970/infotekmesin.v16i1.2532

Abstract

Practical learning activities on heavy equipment units are important because they increase understanding of work systems and provide an actual picture. The need for excavators for practicum activities in vocational education is currently hampered by price issues when commercial units are used as learning tools, therefore learning media in a more concise form are needed without ignoring important aspects. The manufacture of mini excavator props has been carried out but research related to work system testing is still rare, so performance testing of the work system is needed to ensure the performance of the props. The aim of this research is to test cylinder speed, cylinder pressure and cylinder drift using quantitative observation methods with variations in zero capacity, struck capacity and heaped capacity transport. From the test results, it was found that the cylinder speed values ​​were between 0.028–0.081 m/sec, the cylinder pressure was 17–20 bar for the boom, 65–72 bar for the arm, 24–34 bar for the bucket and the increase in length in the cylinder drift test was 0 mm
RANCANG BANGUN DAPUR CRUCIBLE TIPE PENUANGAN TUNGKIK KAPASITAS 15 KG DENGAN BAHAN BAKAR GAS LPG
Infotekmesin Vol 9 No 01 (2018): Infotekmesin, Januari 2018
Publisher : P3M Politeknik Negeri Cilacap

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.35970/infotekmesin.v9i01.1

Abstract

This research aims to; 1) Designing and making aluminium melting crucible casting with the capacity15 kg; 2) Conducting the test of chemical composition of the first and second melting result. Theresearch used field and library research. From the result of the design, it could be obtained that thedimension of melting casting has 547 mm diameter, 3 mm thick, 410 mm high. Whereas, molten cup has 178 mm diameter, 8 mm thick, and 230 mm high. The result of the first melting chemicalcomposition test and the second one do not work out a significant change. The material of the firstmelting result still contains 89,52% of aluminium (Al), while the main fusion is 7,71% of zinc (Zn)and 1,84% of silicon (Si), and in the second melting result still contains 89,55% of Alumunium (Al),while the main fusion is 7,51% of zinc (Zn) and 1,94% of silicon (Si).
APLIKASI KAMUS INGGRIS – INDONESIA DENGAN FITUR SPEECH TO TEXT
Infotekmesin Vol 9 No 01 (2018): Infotekmesin, Januari 2018
Publisher : P3M Politeknik Negeri Cilacap

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.35970/infotekmesin.v9i01.2

Abstract

the use of dictionaries is not only used manually by searching for words in the dictionary book but also digitally which facilitates the work in searching for the meaning of the word. Due to the number of dictionary applications at this time it is done in the development of dictionary applications supported speech to text features in the search he said. Making this application using SQLite database and editor of Android Studio. The use of this dictionary not only functions in searching for the meaning of words, but there is also a list of tensis that comes with text to speech. This application can make it easier to find words and know about tensis. The end result of this application has been tested with several smarthphone with different android version and the result of this application can run well. The drawback of this application is the use of speech to text features that are still online, and data that can be entered into SQLite can not be much and limited, text to speech can not explain tensis accurately.
APLIKASI KAMUS IRREGULAR VERBS BERBASIS ANDROID
Infotekmesin Vol 9 No 01 (2018): Infotekmesin, Januari 2018
Publisher : P3M Politeknik Negeri Cilacap

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.35970/infotekmesin.v9i01.3

Abstract

Irregular is verbs on English do not add with ed or d but change agree with rule. To listen andcomprehend only memorize from verb base make past tense and past participle. Because this resultmany people so think difficult in learning English specially of irregular verbs. Aim of this research is to make application dictionary irregular verbs base android to make support in listen English specially irregular verbs. Scheme of system use Unified Modelling Language, java programming and sqlite database. This research produce a application dictionary irregular verbs to use device mobile base android

Page 33 of 67 | Total Record : 669

 31   32   33   34   35 

Filter by Year

2018 2026


Reset
Filter By Issues
All Issue Vol 17 No 1 (2026): Infotekmesin: Januari 2026 Vol 16 No 2 (2025): Infotekmesin: Juli 2025 Vol 16 No 1 (2025): Infotekmesin: Januari 2025 Vol 15 No 2 (2024): Infotekmesin, Juli 2024 Vol 15 No 1 (2024): Infotekmesin: Januari, 2024 Vol 14 No 2 (2023): Infotekmesin: Juli, 2023 Vol 14 No 1 (2023): Infotekmesin: Januari, 2023 Vol 13 No 2 (2022): Infotekmesin: Juli, 2022 Vol 13, No 2 (2022): Infotekmesin: Juli, 2022 Vol 13 No 1 (2022): Infotekmesin: Januari, 2022 Vol 12 No 2 (2021): Infotekmesin: Juli 2021 Vol 12 No 1 (2021): Infotekmesin: Januari 2021 Vol 11 No 2 (2020): Infotekmesin: Juli 2020 Vol 11, No 1 (2020): Infotekmesin: Januari 2020 Vol 10, No 2 (2019): Infotekmesin: Juli 2019 Vol 10 No 2 (2019): Infotekmesin: Juli 2019 Vol 10 No 1 (2019): Infotekmesin: Januari 2019 Vol 10, No 1 (2019): Infotekmesin: Januari 2019 Vol 9 No 02 (2018): Infotekmesin, Juli 2018 Vol 9, No 02 (2018): Infotekmesin, Juli 2018 Vol 9, No 02 (2018): Infotekmesin, Juli 2018 Vol 9 No 01 (2018): Infotekmesin, Januari 2018 Vol 9, No 01 (2018): Infotekmesin, Januari 2018 More Issue