cover
Contact Name
Muhammad Rifan
Contact Email
m.rifan@unj.ac.id
Phone
-
Journal Mail Official
m.rifan@unj.ac.id
Editorial Address
D3 Elektronika Fakultas Teknik Universitas Negeri Jakarta Gedung L Kampus A UNJ
Location
Kota adm. jakarta timur,
Dki jakarta
INDONESIA
AUTOCRACY: Jurnal Otomasi, Kendali, dan Aplikasi Industri
ISSN : 24070602     EISSN : 26227010     DOI : 10.21009/autocracy
Jurnal ini dimaksudkan sebagai media informasi dan publikasi hasil penelitian, tugas akhir dan kajian ilmiah yang berhubungan dengan bidang elektronika, tenaga listrik, otomasi dan aplikasi industri.
Articles 91 Documents
Rancang Bangun Sistem Kendali Pintu Garasi Menggunakan Android Berbasis Mikrokontroler Atmega16 Hasrul Baki Hasibuan; Muhammad Fahmi Nurfadilah; Efri Sandi
Autocracy: Jurnal Otomasi, Kendali, dan Aplikasi Industri Vol 2 No 01 (2015): Otomasi, Kendali, dan Aplikasi Industri
Publisher : LPPM Universitas Negeri Jakarta

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (349.771 KB) | DOI: 10.21009/autocracy.02.1.4

Abstract

Control System Design of Garage Gate, Using Android Based on Microcontroller ATMEGA16. This study aims to buildautomatic systemof GarageGate,using Bluetooth connection technology,with eksperimen method. Either Hardware and software design or measurementwas done in electrical laboratory, Department of Electrical Engineering, Faculty of Engineering, State University of Jakarta. Preparation and execution of final project had been worked since April 2014 until July 2014. Control system design of garage gate using the Android application was able to open and close the gates using Android application with Bluetooth communication. In the design, Bluetooth communication role has been able to work with a remote control. Remote control worked area is maximum 9 meters, and a distance of 10 meters up, Bluetooth system can no longer respond due to the limited capacity of the Bluetooth module used. Rancang Bangun Sistem Kendali Pintu Garasi Menggunakan Android Berbasis Mikrokontroler ATMEGA16. Penelitian ini menggunakan metode eksperimen dan bertujuan membuat sistem gerbang dan pintu garasi yang dapat bekerja otomatis menggunakan teknologi Bluetooth . Pembuatan perangkat keras, perangkat lunak dan pengujian alat dilakukan di Laboratorium Elektro, Fakultas Teknik Jurusan Teknik Elektro, UNJ. Persiapan dan pembuatan tugas akhir telah dilakukan sejak bulan April 2014 sampai dengan bulan Juli 2014. Sistem pengendalian yang dibuat menggunakan aplikasi Android , dapat menutup dan membuka gerbang dan pintu garasi secara otomatis melalui komunikasi Bluetooth . Fungsi komunikasi Bluetooth menggantikan fungsi remote control. Area kerja dari remote control maksimum 9 meter, sedangkan komunikasi Bluetooth bekerja pada area maksimum 10 meter. Jarak di atas 10 meter tidak dapat mengaktifkan kerja Bluetooth dikarenakan keterbatasan kapasitas dari modul Bluetooth yang digunakan.
Sistem Keamanan Loker Barang Berbasis RFID (Radio Frequency Identification) Dengan Pengendali Arduino Uno Tiur octaviany; Teguh Supriyanto; Syufrijal Syufrijal
Autocracy: Jurnal Otomasi, Kendali, dan Aplikasi Industri Vol 2 No 01 (2015): Otomasi, Kendali, dan Aplikasi Industri
Publisher : LPPM Universitas Negeri Jakarta

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (627.19 KB) | DOI: 10.21009/autocracy.02.1.5

Abstract

This research explores the design and manufacture of goods Locker Security Systems Based Radio Frequency Identification (RFID) uses the controller Arduino Uno. Tool consists of three blocks, namely: block input and control blocks in the form of RFID (controller) using ATmega328 microcontroller and output block limit switch and solenoid. From the results of tests and measurements, obtained that locker security system based on Radio Frequency Identification (RFID) can work in accordance with the description specified. Tools can open and close the locker using RFID door lock automatically by using limit switches and works well. Penelitian ini membahas perancangan dan pembuatan Sistem Keamanan Loker Barang Berbasis Radio Frequency Identification (RFID) menggunakan Pengendali Arduino Uno. Alat terdiri dari tiga blok, yaitu: blok masukan dan blok kendali dalam bentuk RFID (controller) dengan menggunakan mikrokontroler ATmega328 dan output blok limit switch dan solenoid. Dari hasil tes dan pengukuran, diperoleh bahwa sistem keamanan loker berdasarkan Radio Frequency Identification (RFID) dapat bekerja sesuai dengan deskripsi yang ditetapkan. Alat dapat membuka dan menutup loker menggunakan kunci pintu RFID otomatis dengan memanfaatkan limit switch dan bekerja dengan baik.
Simulasi Alat Pendeteksi Magnet Berbasis Mikrokontroler Atmega8535 Taufik Umar; Syufrijal Syufrijal
Autocracy: Jurnal Otomasi, Kendali, dan Aplikasi Industri Vol 2 No 01 (2015): Otomasi, Kendali, dan Aplikasi Industri
Publisher : LPPM Universitas Negeri Jakarta

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (346.638 KB) | DOI: 10.21009/autocracy.02.1.6

Abstract

Magnet Detector Simulation Tool Based on Microcontroller ATMEGA 8535, Diploma III, Electronic Engineering, Department of Electrical Engineering, Faculty of Engineering, University of Jakarta. Magnet Detector Simulation Tool Based on Microcontroller ATMEGA 8535, using a series of sensors and infrared photodiodes and output sensor magnet DC motors. The Magnet Detector Simulation Tool Based on Microcontroller ATMEGA 8535, through some process that has been carried out, including the manufacture of electronic circuits and manufacture of mechanical parts. Further tests performed on each set of systems, from the power supply, the minimum system, magnetic sensors and photodiode. From the experimental results, it can be obtained that the tool has been working in accordance with the job description of a device that is controlled using a microcontroller is programmed using software ATMega8535 Code Vison AVR C Compiler. Simulasi Alat Pendeteksi Magnet Berbasis Mikrokontroler ATMega 8535, D3 Teknik Elektronika, Jurusan Teknik Elektro, Fakultas Teknik, Universitas Negeri Jakarta. Simulasi Alat Pendeteksi Magnet Berbasis Mikrokontroler ATMega 8535 mikrokontroler menggunakan serangkaian sensor dan fotodioda inframerah dan output sensor magnet motor DC. Simulasi Alat Pendeteksi Magnet Berbasis Mikrokontroler ATMega 8535, melalui beberapa proses yang dilakukan, termasuk pembuatan sirkuit elektronik dan pembuatan bagian-bagian mekanik pada alat. Pengujian lebih lanjut dilakukan pada setiap rangkaian sistem dilakukan, mulai dari power supply, sistem minimum, sismin, sensor magnetik dan fotodioda. Dari hasil percobaan dapat diperoleh bahwa alat untuk bekerja sesuai dengan job description dari alat yang akan dikontrol menggunakan mikrokontroler ATMega8535 diprogram menggunakan software Code Vison AVR C Compiler.
Bantal Pintar Alarm dan Nyanyian Pengiring Tidur Berbasis Mikrokontroler Atmega 16 Agung Tyas Utomo; Muhammad Abduh Wicaksana; Pitoyo Yuliatmojo
Autocracy: Jurnal Otomasi, Kendali, dan Aplikasi Industri Vol 2 No 01 (2015): Otomasi, Kendali, dan Aplikasi Industri
Publisher : LPPM Universitas Negeri Jakarta

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (225.714 KB) | DOI: 10.21009/autocracy.02.1.7

Abstract

The purpose of this study is, make pillows to help a person can sleep and wake up on time. This tool uses minimum system, RTC module, MP3 module, buzzer, LCD, Module Amplifier and speakers. Where these tools present on the LCD alarm clock uses minimum system, RTC and alarm module works with a loud voice, the sound released by the speaker using MP3 and Amplifier Module as an amplifier.The method is used as follows: Display Settings and Relay circuit, making mechanical, electronic circuits, making the program and testing. The results of experiments using ATmega8 microcontroller running and all components function properly. Tujuan dari penelitian ini adalah membuat bantal untuk membantu seseorang dapat tidur dan bangun tepat waktu, alat ini menggunakan sistem minimum, RTC modul, modul MP3, Buzzer, LCD, Modul Amplifier dan speaker. Dimana alat ini menyajikan jam alarm pada LCD menggunakan sysmin, Modul RTC dan alarm berkerja dengan suara yang keras, suara dikeluarkan oleh speaker menggunakan Modul MP3 dan Amplifier sebagai penguat. Langkah yang dilakukan meliputi: Pengaturan Tampilan dan sirkuit Relay, membuat mekanik, sirkuit elektronik, pembuatan program dan pengujian. Hasil eksperimen menggunakan mikrokontroler ATmega8 berjalan dan semua komponen berfungsi dengan baik.
Prototipe Sistem Pemberitahuan Bus Transjakarta Menggunakan RFID Untuk Identifikasi Halte Berbasis Arduino Mega 2560 Devan Reyanda; Achmad Gayuh Raharjo; Muhammad Yusro
Autocracy: Jurnal Otomasi, Kendali, dan Aplikasi Industri Vol 2 No 02 (2015): Otomasi, Kendali, dan Aplikasi Industri
Publisher : LPPM Universitas Negeri Jakarta

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (356.407 KB) | DOI: 10.21009/autocracy.02.2.1

Abstract

Prototype System notification of Bus Transjakarta used RFID for identification shelter based Arduino Mega 2560, Final Project Diploma Program Department of Electronic Engineering, Faculty of Engineering, State University of Jakarta, 2015.This final project discusses about Prototype System notification of Bus Transjakarta is using RFID for identification shelter based Arduino Mega 2560. The system of Bus Transjakarta are using RFID Reader ID-12, WTV020m01, Arduino Mega 2560, LCD Display, Speaker, DC Motor and Driver Motor. This information system control using Arduino Mega 2560.From the result of notification analysis with RFID , Arduino Mega 2560, WTV020m01, LCD Display, Speaker, Driver Motor,and Motor DC. It can be concluded that the prototype system Transjakarta Bus stop using RFID for identification based Arduino Mega 2560 can work well. Prototype Sistem Pemberitahuan Bus Transjakarta Manggunakan RFID untuk identifikasi halte Berbasis Arduino Mega 2560, Tugas Akhir Program Studi DIII Teknik Elektronika Jurusan Teknik Elektro, Fakultas Teknik Universitas Negeri Jakarta, 2015. Tugas Akhir ini membahas tentang Prototype Sistem Pemberitahuan Bus Transjakarta menggunakan RFID untuk identifikasi halte berbasis Arduino Mega 2560. Sistem pemberitahuan Bus Tranjakarta menggunakan RFID Reader ID-12, WTV020m01, Arduino Mega 2560, LCD Display, Speaker, Motor DC dan Driver Motor. Kontrol sistem pemberitahuan ini menggunakan Arduino Mega 2560. Dari hasil analisa sistem pemberitahuan menggunakan RFID, Arduino Mega 2560, WTV020m01, LCD Display, dan Speaker, Driver Motor dan Motor DC. Dapat disimpulkan bahwa prototype sistem Bus Transjakarta menggunakan RFID untuk identifikasi halte berbasis Arduino Mega 2560 dapat bekerja dengan baik
Aplikasi Scada Pada Sistem Pengendalian Trainer Lift Menggunakan OPC berbasis PLC Syufrijal Syufrijal
Autocracy: Jurnal Otomasi, Kendali, dan Aplikasi Industri Vol 2 No 02 (2015): Otomasi, Kendali, dan Aplikasi Industri
Publisher : LPPM Universitas Negeri Jakarta

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (731.553 KB) | DOI: 10.21009/autocracy.02.2.2

Abstract

This research aims to control three-story elevator trainers automatically using PLC and SCADA with OPC interface KepserverEx.PLC Omron CSG1H is used as an elevator trainer controller with 14 inputs and 6 outputs. The input equipment is a call button outside the elevator on each floor and calls in the elevator and limit switch. Limit switch serves to detect the presence of elevators on each floor. The output equipment is a relay. This relay will control the motor lift in order to rise / fall quickly or slowly and control the elevator door indicator lights. The method used in this research is an experimental method that is to design and test the program to then apply it to the tool. The mechanism of control system design and elevator trainer monitoring starts from making system work description, assigning I/O PLC address, connecting input and output equipment to PLC, making PLC and SCADA program, making communication program between PLC and SCADA through OPC KepserverEx. From the results of the study, three-story elevator trainers can work automatically according to desirable job descriptions and work processes can be monitored on a computer screen. Penelitian ini bertujuan untuk mengendalikan trainer lift bertingkat tiga secara otomatis menggunakan PLC dan SCADA dengan interface OPC KepserverEx. PLC Omron CSG1H digunakan sebagai pengendali trainer lift dengan 14 input dan 6 output. Peralatan input tersebut berupa tombol panggilan luar lift yang ada di setiap lantai dan panggilan dalam lift serta limit switch. Limit switch berfungsi untuk mendeteksi keberadaan lift di setiap lantai. Adapun peralatan keluarannya berupa relay. Relay ini yang akan mengendalikan motor lift agar dapat naik/turun dengan cepat atau lambat dan mengendalikan lampu indikator pintu lift. Metode yang digunakan dalam penelitian adalah metode eksperimen yaitu merancang dan melakukan uji program untuk kemudian menerapkannya pada alat. Mekanisme perancangan sistem pengendalian dan monitoring trainer lift dimulai dari membuat deskripsi kerja sistem, menetapkan alamat I/O PLC, menghubungkan peralatan input dan output ke PLC, membuat program PLC dan SCADA, membuat program komunikasi antara PLC dan SCADA melalui OPC KepserverEx. Dari hasil penelitian, trainer lift bertingkat tiga dapat bekerja secara otomatis sesuai deskripsi kerja yang diinginkan dan proses kerjanya dapat termonitor di layar komputer.
Prototipe Pengisian Oli Berdasarkan jumlah Kapasitas Oli Berbasis PLC Erlita Ria Wulandari; Riyad Maulana; Jusuf Bintoro
Autocracy: Jurnal Otomasi, Kendali, dan Aplikasi Industri Vol 2 No 02 (2015): Otomasi, Kendali, dan Aplikasi Industri
Publisher : LPPM Universitas Negeri Jakarta

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1038.607 KB) | DOI: 10.21009/autocracy.02.2.3

Abstract

This research create a prototype filling oil by quantity capacity based on PLC (Programmable Logic Controller). In this system, refueling oil differentiated based on the amount of its capacity is 800ml and 1000ml using Mitsubishi PLC FX1N with software GX Developer program and used photodiode sensor to detect the height of object that will be filled oil. The purpose of this final project is to design and create a filling oil otomatic system which work effectively and efficiently in addressing the problems of producing a different of oil capacity with uses photodiode sensor, regulator circuit, and conveyor. PLC as controller this system. Based on test result of all, it can be concluded that Prototype filling oil by quantity capacity Based on PLC (Programmable Logic Controller) can work well with error factor of 1%. Penelitian ini membuat prototipe pengisian oli berbasis PLC (Programmable Logic Controller). Pada sistem ini, pengisian oli dibedakan berdasarkan jumlah kapasitasnya yaitu 800ml dan 1000ml menggunakan PLC Mitsubishi FX1N dengan program Software GX Developer serta menggunakan sensor photodioda untuk mendeteksi ketinggian benda yang akan diisi oli. Tugas Akhir dibuat dengan tujuan untuk merancang dan membuat sebuah alat pengisian oli otomatis yang dapat bekerja secara efektif dan efisien dalam mengatasi permasalahan memproduksi jumlah oli yang berbeda kapasitasnya dengan menggunakan sensor photodioda, rangkaian regulator dan konveyor. Kendali sistem ini menggunakan PLC. Dari hasil pengujian secara keseluruhan dapat disimpulkan bahwa prototipe pengisian oli berdasarkan jumlah kapasitas oli berbasis PLC (Programmable Logic Controller) dapat bekerja dengan baik dengan faktor kesalahan sebesar 1%.
PLC Berbasis Mikrokontroler Atmega16 Sebagai Pengganti PLC Konvensional Adi Brama; Syafi’i Agus Kurniawan; Mochammad Djaohar
Autocracy: Jurnal Otomasi, Kendali, dan Aplikasi Industri Vol 2 No 02 (2015): Otomasi, Kendali, dan Aplikasi Industri
Publisher : LPPM Universitas Negeri Jakarta

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (924.603 KB) | DOI: 10.21009/autocracy.02.2.4

Abstract

Making the research aims to design and build a PLC (Programmable Logic Controller) that uses a microcontroller ATmega16 as the brain of the Micro PLC system. The process of manufacture, testing is done in simulation tools at Pustikom State University of Jakarta and completed the process in May-June 2015. PLC Microcontroller ATmega16-Based As Substitute Conventional PLC, and use the application on a laptop LDmicro to make instructions that form the ladder program to run the output in the form of LED, AC Lamp 8W, Motor 1 Phase, and Solenoid Electric.The result of Micro PLC research have successfully created and tested with the results of voltage for each I/O and other circuits with measurement results. The results obtained after the system was tested as a whole, so that it can be concluded that the PLC Microcontroller ATmega16-Based As Substitute Conventional PLC can work well. Pembuatan penelitian ini bertujuan untuk merancang dan membangun sebuah PLC (Programmable Logic Controller) yang menggunakan mikrokontroler ATmega16 sebagai otak dari sistem PLC Mikro tersebut. Proses pembuatan, pengujian simulasi alat dilakukan di Pustikom Universitas Negeri Jakarta dan diselesaikan pengerjaannya pada bulan Mei-Juni 2015. PLC Berbasis Mikrokontroler ATmega16 Sebagai Pengganti PLC Konvensional, menggunakan ATmega16 sebagai pengendali sistem PLC Mikro tersebut, dan menggunakan aplikasi LDmicro pada laptop untuk membuat instruksi-instruksi yang berupa program ladder untuk menjalankan output yang berupa LED, Lampu AC 8W, Motor 1 Phasa, dan Solenoid Electric. Hasil penelitian PLC Mikro telah berhasil dibuat dan diuji dengan hasil tegangan untuk masing-masing I/O dan rangkaian lainnya dengan hasil pengukuran. Hasil tersebut diperoleh setelah sistem diuji secara keseluruhan, sehingga dapat disimpulkan bahwa PLC Berbasis Mikrokontroler ATmega16 Sebagai Pengganti PLC Konvensional dapat bekerja dengan baik.
Sistem Monitoring Kwh Meter Analog Berbasis Sms Gateway Rian Pratama; Vanessa Chita Tifani; Wisnu Djatmiko
Autocracy: Jurnal Otomasi, Kendali, dan Aplikasi Industri Vol 2 No 02 (2015): Otomasi, Kendali, dan Aplikasi Industri
Publisher : LPPM Universitas Negeri Jakarta

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (534.596 KB) | DOI: 10.21009/autocracy.02.2.5

Abstract

In the daily life of society we must recognize a device called KWH analog meter, which is a tool used by PT. PLN (Persero) to calculate the power consumption of consumers. But this time KWH existing analog meter does not notify large electric power and the cost we have to pay clearly. So we made "KWH Meter Monitoring System Based Analog SMS Gateway" which can send an SMS (Short Message Service) containing large power consumption as well as costs periodically to the users The working principle of this device using the workings of the current sensor ACS712 Smart DI-5A. First current sensor ACS712 5A DI-Smart will be calibrated first by Analog to Digital Converter (ADC), and then when there is current through KWH meters it will be read by the current sensor ACS712 5A DI-Smart this. Furthermore, the data generated by the current sensor ACS712 5A DI-Smart will be processed by microcontroller ATmega16 and will the output can be viewed on LCD (Liquid Crystal Display) simultaneously sent to the modem GSM (Global System for Mobile Communication) Shield ago will send space usage electricity and costs to be paid in the form of SMS. Dalam kehidupan sehari-hari masyarakat pastilah kita mengenal sebuah alat yang disebut dengan KWH meter analog, yaitu suatu alat yang digunakan oleh PT. PLN (Persero) untuk menghitung besar pemakaian daya listrik konsumen. Namun selama ini KWH meter analog yang ada tidak memberitahukan besar daya listrik serta biaya yang harus kita bayar secara jelas. Sehingga dibuat ‘Sistem Monitoring KWH Meter Analog Berbasis SMS Gateway’ yang dapat mengirimkan SMS (Short Message Service) besar pemakaian listrik serta biaya secara berkala kepada pengguna KWH meter. Prinsip kerja Sistem Monitoring KWH Meter Berbasis SMS Gateway ini menggunakan cara kerja sensor arus DI-Smart ACS712 5A. Pertama sensor arus DI- Smart ACS712 5A akan dikalibrasi oleh Analog to Digital Converter (ADC), lalu saat arus melewati KWH meter maka akan dibaca sensor arus DI-Smart ACS712 5A. Lalu data yang dihasilkan sensor arus DI-Smart ACS712 5A akan diproses mikrokontroler ATMega16 dan menghasilkan keluaran di LCD (Liquid Crystal Display) sekaligus dikirimkan ke modem GSM (Global System for Mobile Communication) Shield yang lalu akan mengirimkan besar pemakaian listrik dan biaya yang harus dibayarkan dalam bentuk SMS.
Sistem Keamanan Helm Berbasis RFID Adnan Septian; Muhammad Faris Nurrahman; Agung Wibisono
Autocracy: Jurnal Otomasi, Kendali, dan Aplikasi Industri Vol 2 No 02 (2015): Otomasi, Kendali, dan Aplikasi Industri
Publisher : LPPM Universitas Negeri Jakarta

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (561.373 KB) | DOI: 10.21009/autocracy.02.2.6

Abstract

This research was created with the purpose to make the helmet more secure when left to the parking place. With the implementation of RFID technology meal will provide comfort and convenience for the user in the helmet leaving the parking place. With good security, system users can open and lock the helmet with an RFID tag card that she has. The research method design Helmet-Based Security System RFID. begins with making the concept of project tools made by the method of literature from the source book and datasheet, followed by how the final design tools and tools that will be used must be adapted to the needs of the design of systems that have been designed previously. Penelitian ini dibuat dengan tujuan untuk menjadikan helm lebih aman ketika ditinggal ditempat parkir. Dengan penerapan teknologi RFID makan akan memberikan kenyamanan dan kemudahan bagi pengguna dalam meninggalkan helm ditempat parkir. Dengan keamanan yang bagus, pengguna sistem ini dapat membuka dan mengunci helm dengan kartu tag RFID yang dia punya. Metode penelitian rancang bangun sistem keamanan helm berbasis RFID diawali dengan membuat konsep dari project alat yang dibuat dengan metode kepustakaan dari sumber buku dan datasheet, kemudian dilanjutkan dengan bagaimana cara kerja alat dan terakhir desain alat yang akan digunakan harus disesuaikan dengan kebutuhan dengan desain sistem yang telah dirancang sebelumnya. Dari hasil penelitian sentral lock dapat digunakan untuk mengunci helm ketika kartu tag terbaca oleh reader RFID dan terbuka ketika kartu tag terbaca oleh reader.

Page 2 of 10 | Total Record : 91