cover
Contact Name
-
Contact Email
-
Phone
-
Journal Mail Official
-
Editorial Address
-
Location
Kota medan,
Sumatera utara
INDONESIA
Jurnal Teknik Kimia USU
ISSN : -     EISSN : -     DOI : -
Arjuna Subject : -
Articles 349 Documents
PENGARUH PENAMBAHAN NATRIUM KLORIDA (NaCl) DAN WAKTU PERENDAMAN BUFFER FOSFAT TERHADAP PEROLEHAN CRUDE PAPAIN DARI DAUN PEPAYA (CARICA PAPAYA, L.) Pinta Rizki Mala Hasibuan, Mitha Alviyulita, Farida Hanum
Jurnal Teknik Kimia USU Vol 3, No 3 (2014)
Publisher : Universitas Sumatera Utara

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (333.225 KB) | DOI: 10.32734/jutek.v3i3.8152

Abstract

Papaya (Carica papaya L.) is one of the fruits of commodities internationally, either in the form of fresh fruit or as processed products. The leaves are green still not fully utilized. Papaya leaves contains papain enzyme which is a protease enzyme that very helpful for  the industry. Papain is a protease enzyme contained in papaya latex, whether in fruit, stems and leaves, as an enzyme capable of solving the protein molecules, current papain into products that are beneficial to human life, either at home or industrial ladder. This study aims to determine the effect of the degree of saturation of sodium chloride  and phosphate buffer to yield soaking rough papaya protease. This study varying the time of immersion phosphate buffer and saturation levels of sodium chloride. Analysis of protease activity was performed using UV-Vis spectrophotometer to measure the wavelength and absorbance values​​. The best research results obtained at 12 h immersion phosphate buffer with a concentration of sodium chloride 60% is 272.8222 unit / ml. In the analysis of the rendemen obtained by the best condition at the time of immersion phosphate buffer for 36 hours at a concentration of 90% is 43,5152%. In the analysis of moisture content obtained the best condition at the time of immersion of 36 hours at a concentration of 90% is 37.4266%.
PENGARUH WAKTU FERMENTASI TERHADAP PERSENTASE PENYISIHAN CHEMICAL OXYGEN DEMAND (COD) CAMPURAN LIMBAH CAIR INDUSTRI TAPIOKA DAN AIR Umayi Belladiana, Wan Rizki Ansari, Setiaty Pandia
Jurnal Teknik Kimia USU Vol 3, No 3 (2014)
Publisher : Universitas Sumatera Utara

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (430.434 KB) | DOI: 10.32734/jutek.v3i3.8165

Abstract

Study about the effect of fermentation time on the percentage removal of chemical oxygen demand (COD) a mixture of tapioca liquid industrial waste and water that aims to determine the effect of water quality and quantity of bio-gas generated from tapioca industrial wastewater combined with water. The research was conducted by combining tapioca industrial wastewater with water on several compositions, namely 100: 0; 85:15; 65:35; 50:50; 35:65; 15:85 (v / v) with cow dung starter in the batch anaerobic digester systems for 24 days with a neutral pH. The optimum percentage of allowance for COD at the ratio of tapioca  liquid industrial waste and water at  15:85 with a value of 42.14% where the value of COD on day 0 was 1723 mg / L after day 24 was 997 mg / L .
PENGHILANGAN TINTA PADA KERTAS THERMAL BEKAS : PENGARUH KONSISTENSI DAN KONSENTRASI PENDISPERSI FLOTASI Sulastri Dewanti, Elisabet Aprilyanti, Taslim
Jurnal Teknik Kimia USU Vol 3, No 4 (2014)
Publisher : Universitas Sumatera Utara

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.32734/jutek.v3i4.8493

Abstract

Recycling of wastepaper is a solution for paper industry to overcome the scarcity and the limited presence of the virgin pulp sources. Thermal paper is a highly engineered product coated with a thermal sensitive layer that reacts in the presence of heat to create the printed image. The purpose of this research is to study the effect of pulp consistency  and dispersant concentration on the removal of ink in the thermal paper. There are 3 steps in this research which are immersing, pulping and flotation. The results of this research were measured according to TAPPI and SNI to determine the brightness and tensile strength of the recycled paper, respectively. The excellent conditions were obtained at  pulp consistency of 0.8%, dispersant concentration of 1.5%, flotation temperature of 50 °C and flotation time of 40 minutes. In these conditions, the brightness was 72,17% and tensile strength was 3.7 kN/m.
PEMANFAATAN ADSORBEN DARI BIJI ASAM JAWA UNTUK MENURUNKAN BILANGAN PEROKSIDA PADA CPO (CRUDE PALM OIL) Agus Mangiring Siburian, Agnes Sartika Doharma Pardede, Setiaty Pandia
Jurnal Teknik Kimia USU Vol 3, No 4 (2014)
Publisher : Universitas Sumatera Utara

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (179.67 KB) | DOI: 10.32734/jutek.v3i4.8622

Abstract

This study was aimed to discover the effectiveness of tamarind seeds as adsorbent for the reduction of PV (Peroxide Value) in CPO (Crude Palm Oil) at the best adsorbent dose and contact time. Materials used were CPO, tamarind seeds, nitric acid, and distilled water. Variables observed were adsorbent : nitric acid ratio and oven temperature in adsorbent activation process, and contact time and adsorbent dose in adsorption process. This study was began with adsorbent modification, where the  cleaced and crushed tamarind seeds to pass through 140 mesh were activated with 4 N nitric acid at 1:1, 1:2, 1:3 and 1:4 of adsorbent : nitric acid ratio while heated at 80 oC for 2 hours. Adsorbent was then dried in oven at 110 oC, 120 oC, 130 oC and 140 oC. Adsorbent with the higher iodine number was used in adsorption process that was carried out by heating 100 grams of CPO on hot plate at 90 oC with 1000 rpm of stirring speed, and followed by adsorbent addition of 0.5 %, 1,0 %, and 1,5 % (of CPO used) and 25, 35, and 45 minutes of contact time, and after that oil was filtered using vacuum pump. The study results showed that the best ratio of adsorbent : nitric acid 4 N was 1:2 at 130 oC of oven temperature with 511.773 mg/g of iodine number. The best adsorbent dose was 1.0 % at 35 minutes of contact time that gave higher reduction of PV with peroxide value of 0,00868 meq/kg with the reduction percentage was 39,72 %. This study showed that nitcic acid-activated adsorbent from tamarind seeds was effective to reduce PV in CPO.
PENGARUH PENAMBAHAN RESORSINOL PADA PEMBUATAN PEREKAT LIKUIDA SABUT KELAPA Mutiara Istiqomah, Netti Herlina
Jurnal Teknik Kimia USU Vol 3, No 4 (2014)
Publisher : Universitas Sumatera Utara

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (245.902 KB) | DOI: 10.32734/jutek.v3i4.8777

Abstract

Liquid adhesive coconut coir is the result of a reaction between lignin powder material used with aromatic compounds at high temperatures in order to obtain a solution that can be used as an adhesive. This study aims to investigate the characteristics of liquid adhesive of coconut coir (LACC) qualities  and determine the effect of resorcinol in the manufacture of adhesives LACC. The study was conducted in three phases: the first stage of coir manufacturing particles, which at this stage coir made into particles of 100 mesh, adhesive manufacturing second stage LACC which at this stage there are two stages of the liquefaction reaction coir and polymerization, and the third stage addition of resorcinol LACC into the adhesive. The variables used in this study is the addition of variable rate resorcinol at 10, 20, 30% by weight. Variables - variables that were analyzed pH, viscosity, spesific gravity, solid content, formaldehyde-free rate and compound analysis using FT-IR adhesive LACC to conditions without the addition of resorcinol and with the addition of 30% resorcinol. The results showed that the addition of resorcinol LACC influence on the resulting adhesive, which has a liquid form, the pH ranged from 12.6 to 10.6, 43,867- 131.712 cps viscosity, specific gravity of 1.252 to 1.258, solid content 46.67 to 80%, from 1.952 to 1.051% formaldehyde content. FT-IR results showed similarity LACC adhesive force phenol formaldehyde resin, namely the presence of the OH group, C = H of the aromatic ring, of methylene CH, CO from ether and fenolic compound.
PENGARUH PELARUT TERT-BUTANOL TERHADAP MINYAK DAN SUHU REAKSI GLISEROLISIS PADA PEMBUATAN MONO DAN DIASILGLISEROL (MDAG) MENGGUNAKAN KATALIS ABU CANGKANG TELUR AYAM Retno Dian Lestari Purba, Margareth Nainggolan, M. Yusuf Ritonga
Jurnal Teknik Kimia USU Vol 3, No 4 (2014)
Publisher : Universitas Sumatera Utara

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (106.923 KB) | DOI: 10.32734/jutek.v3i4.8890

Abstract

Mono and diacylglycerol (MDAG) is one of the synthetic emulsifier agent widely used in food industry. Emulsifier agent is one of the economically high value oleochemical product. The purpose of this research is to produce MDAG through glycerolysis process of refined bleached deodorize palm oil (RBDPO) and glycerol by using egg shell waste as catalyst (4 % of oil weight) for 2 hours, whereas the variables ratio of tert-butanol to oil (1, 2, 3 v/w) and reaction temperatur (60, 70 and 80 oC). Egg shell waste was calcined at  900 oC for 2 hours to form active CaO catalyst. Then glycerolysis process to produce mono and diacylglyserol. Mono and diacylglycerol that formed was separated by using separator fannel. The upper layer was vaporated to separate MDAG from tert-butanol. The content of MDAG was analyzed using Gas Chromatography. The best result was at 70 oC temperature, ratio co-solvent to oil 3:1 (v/w), 2 hours of reaction time and 4% of catalyst amount from oil and oil molar ratio to glycerol 1:6 with MDAG content of 68,62%. MDAG formed are w/o emulsifier with 5.19 HLB. The result of this research shows that egg shell waste is suitable to be used as source of cheap catalyst to produce mono and diacylglycerol.
PEMANFAATAN KITOSAN DARI CANGKANG BEKICOT (Achatina fulica) SEBAGAI PENGAWET IKAN KEMBUNG (Rastrelliger sp) DAN IKAN LELE (Clarias batrachus) Sari Wahyu Waryani, Rika Silvia, Farida Hanum
Jurnal Teknik Kimia USU Vol 3, No 4 (2014)
Publisher : Universitas Sumatera Utara

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (89.197 KB) | DOI: 10.32734/jutek.v3i4.8987

Abstract

The efforts that should be made to maintain the quality of fish is by using antimicrobial compounds, one of which is chitosan. In this research, characterization of chitosan from shell snail (Achatina fulica) has a water content of 5.07%, ash content of 1.8% and the degree of deacetylation (DD) 75.13%. The use of chitosan in this study was to determine the optimal conditions on chitosan concentration and storage time of mackerel (Rastrelliger sp) and catfish (Clarias batrachus) from the microbiological and organoleptic aspects. This research used a variation of the concentration of chitosan was 1%, 1.5%, 2% and 2.5% dissolved in 1% acetic acid. Observations were do with variation the storage time 10 hours, 15 hours, 20 hours and 25 hours and the provision of chitosan solution by soaking and spraying with the observation parameters Total Volatile Base (TVB), organoleptic and pH of fish. Based on the analysis, the results showed that the maximum concentration of chitosan on mackerel (Rastrelliger sp) and catfish (Clarias batrachus) is 1,5% and treatment by means of immersion is the best treatment. The use of chitosan solution on mackerel (Rastrelliger sp) survived 20 hours while catfish (Clarias batrachus) survived 15 hours.Keywords :Total Volatile Base, organoleptic, pH, mackerel, catfish
PEMBUATAN ASAM OKSALAT DARI ALANG-ALANG (Imperata Cylindrica) DENGAN METODE PELEBURAN ALKALI Iriany, Andrew Faguh Sitanggang, Rahmad Dennie A. Pohan
Jurnal Teknik Kimia USU Vol 4, No 1 (2015)
Publisher : Universitas Sumatera Utara

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.32734/jutek.v4i1.8993

Abstract

Imperata grassland is one of the wild plant which have a low economic value but containing high cellulose. Therefore it is potentially to be used as raw material for  oxalic acid manufacturing. The oxalic acid can be produced from imperata grassland through 4 steps: alkaline hydrolysis, precipitacion, acidification and crystallization. Experiments are carried out in a three necks glass equipped with thermometer, mixer, heater and condenser. Cooking solution NaOH  were varied 3,5 N; 4 N  and 4,5 N and cooking time 50, 60, 70 and 80 minutes. According to the result from the experiment, at the condition 98oC of cooking temperature, the highest yield of oxalic acid about 44,39% is obtained at 4 N concentration of sodium hydroxide and 60 minute of cooking time. Oxalic acid produced has 104oC of melting point  and 1,2 of degree of acidity (pH).  
JTK USU Journal Management
Jurnal Teknik Kimia USU Vol 3, No 4 (2014)
Publisher : Universitas Sumatera Utara

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (6.381 KB) | DOI: 10.32734/jutek.v3i4.9074

Abstract

JTK USU
ANALISIS LAJU ALIR SAMPAH DAN EMISI CARBON YANG DIHASILKAN KOTA BANDA ACEH M. Faisal
Jurnal Teknik Kimia USU Vol 3, No 4 (2014)
Publisher : Universitas Sumatera Utara

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (212.317 KB) | DOI: 10.32734/jutek.v3i4.9076

Abstract

This research aims to analyze the material flow of solid waste of  Banda Aceh city by using Material Flow Analysis (MFA) method. The domestic wastes used in this research are limited to organic waste, plastic and paper.  Results show that the solid wastes in Banda Aceh city do not treated well and thus required further treatment process. Wastes are separated at the kampong Jawa waste treatment process. Leaves waste are treated for compost, while no treatment process for plastic and paper wastes. The percentage of organic wastes, paper and plastic produced from Banda Aceh city were 89,1 %; 2,5 %; 0,74 %, respectively. Total amount of waste in the city of Banda Aceh is 86057,64 t/month producing carbon emission of 83726,6 t/month.

Page 9 of 35 | Total Record : 349