Garuda - Garba Rujukan Digital

All

Jurnal technoscientia

technoscientia
Website

Published by Institut Sains dan Teknologi AKPRIND

ISSN : 19798415 EISSN : - DOI : -

Chemical Engineering, Chemistry & Bioengineering Computer Science & IT Industrial & Manufacturing Engineering Materials Science & Nanotechnology Mechanical Engineering

Arjuna Subject : -

Articles 583 Documents

20 21 22 23 24

MODAL TESTING AND FINITE ELEMENT MODEL UPDATING OF TWO NOMINALLY IDENTICAL CONCRETE BUILDING FLOORS Widjaja, Taufik Ramlan
JURNAL TEKNOLOGI TECHNOSCIENTIA Technoscientia Vol 2 No 1 Agustus 2009
Publisher : Lembaga Penelitian & Pengabdian Kepada Masyarakat (LPPM), IST AKPRIND Yogyakarta

This paper describes a combined approach of modal testing and finite element (FE) analysis for vibration analysis of a structural system comprising two nominally identical concrete building floors located at adjacent levels. Initially, a field test of a full-scale joint two-level floor system was conducted to obtain the first five mode shapes and natural frequencies. Sensitivity-based FE model correlation and updating were then con-ducted to match the dynamic characteristics of the FE model with the experimental data. By setting certain indicators of good correlations between analytical and experimental models, an updated FE model comprising two nominally identical building floor was obtained.

PERUBAHAN LAJU KOROSI AKIBAT TEGANGAN DALAM DENGAN METODE C-RING Rusianto, Toto
JURNAL TEKNOLOGI TECHNOSCIENTIA Technoscientia Vol 2 No 1 Agustus 2009
Publisher : Lembaga Penelitian & Pengabdian Kepada Masyarakat (LPPM), IST AKPRIND Yogyakarta

Stress Corrosion Craking (SCC) generally attack to metals (steel) under internal stress. Fastener could arised internal stress to material that fastened, such as plat or other material. The experiment to observed SCC could used C-Ring method as standard ASTM G38-01(2007). Fastener and base material that made C-ring corroded in sea water with various stresses that was arrised by fastener. The result of research showed that hardness of spesimen (fastener and C-ring) was increase with increase in stress, the hardness indicated there were internal stress in spesimen. Corrosion rate for spesimen was increase with increase in stress, the higher corrosion rate at spesimen of C-ring for arrised stress 256 kg was 24,20 MPY. and lower arrised stress 69 kg was 19,14 MPY. The spesimen of fastener for arrised stress 256 kg was 7,97 MPY. and lower arrised stress 69 kg was 6,89 MPY. Duration experiment time were 9 day.

THE BREEDING OF LOCAL CORN BY MULTIGAMMA RADIATION METHOD (NUCLEAR) IN WEST TIMOR NUSA TENGGARA TIMUR Pasangka, Bartholomeus
JURNAL TEKNOLOGI TECHNOSCIENTIA Technoscientia Vol 3 No 1 Agustus 2010
Publisher : Lembaga Penelitian & Pengabdian Kepada Masyarakat (LPPM), IST AKPRIND Yogyakarta

Corn is one of Nusa Tenggara Timur main commodities. This plant has prospect to be increased in NTT, because it is adapted to the soil which has calcium deposits with relative low rainfall (dry soil) and high salinity. This research aimed to develop local corn variety through breeding by multi-gamma radiation method, selection, and crossing to obtain the prime seed of the local corn with different characteristics to its source plant.The method of research is breeding of local corn using gamma and multi-gamma radiation methods to produce several varieties of prime seed, so is very easy to select and obtain the prime seed of local corn. The other methods are comprised of observation, sampling, analysis, comparative, and interpretation.The result obtained on the first step (first year) is the selected mutation variety (the prime seed of local corn) with production 11 tons per ha (local yellow corn) and 9 tons per ha (local white corn). The production increase 36.4% (local yellow corn) and 33.3% (local white corn). On the second step (first year), obtained addition variety of selected mutation and more superior variety is resulted of crossing with production 13 tons per ha (local yellow corn) and 10 tons per ha (local white corn). The production increases 46.2% (local yellow corn) and 40.0% (local white corn). These results show that the breeding of local corn by multi-gamma radiation method and crossing can produce primer seed and has a certain quality to increase production significantly of the farmer on the sector of corn commodity.

MIKROFASIES DAN DIAGENESA BATUGAMPING FORMASI ZAAG DI PULAU MISOOL DAN SEKITARNYA Mulyadi, Dedi
JURNAL TEKNOLOGI TECHNOSCIENTIA Technoscientia Vol 3 No 1 Agustus 2010
Publisher : Lembaga Penelitian & Pengabdian Kepada Masyarakat (LPPM), IST AKPRIND Yogyakarta

The study of carbonate rocks of Zaag Formation shows that the carbonate rock of Paleo-cene-Eocene occurred in Misool Island and outcropped among the rock of Paleozoikâ€“ Tertiary. The field survey shows that the Zaag Formation is outcropped at the mid part of the Misool Island from the west to east and also at several the surrounding small islands. The petrography analysis indicated that there are two facies forming the Zaag Formation, indicated found it was form at shoal environment of Packstone Facies and Grainstone Facies. The diagenesis process observed at the thin section is micritisation, cementation, dissolution and tectonic activity.

IDENTIFIKASI GERAKAN TANAH DI DAERAH TINATAH KECAMATAN ALIANâ€“KEBUMEN Nur, Arief Mustofa
JURNAL TEKNOLOGI TECHNOSCIENTIA Technoscientia Vol 2 No 2 Februari 2010
Publisher : Lembaga Penelitian & Pengabdian Kepada Masyarakat (LPPM), IST AKPRIND Yogyakarta

Land movements in Tinatah, Alian Districtâ€“Kebumen occured since 2005. Ap-proximately 40 families from 80 families are in high risk when rapid landslides occur in this area. The aim of this study is to identified the high risk and relatively safe areas. The used method was by field survey to obtain natural conditional data, landslide indications, range finder measured to local topographic map, laboratory analysis of engineering properties of soils, and evaluation of potential landslide. The study finds land movements in Tinatah area were caused by lithology of marl-claystone, structural geology of trace of anticline and fault. The low of slope causing land movement very slow with creeping type. The highest risk area is the trace of anticline with marl-claystone lithology (RT 6 RW 2). The more stable locations are the location with calcarenite lithology (RT 8 RW 2) and andesite breccia (Kalinanas). Anticipatory steps that can be done by stabilize of slope, drainage regulation, socialization, relocation to more stable places.

APLIKASI STREAMING MULTIMEDIA PADA M-DOCTOR DENGAN SELULAR WCDMA Santoso, Gatot; Sutanta, Edhy; Wibowo, Samekto
JURNAL TEKNOLOGI TECHNOSCIENTIA Technoscientia Vol 3 No 1 Agustus 2010
Publisher : Lembaga Penelitian & Pengabdian Kepada Masyarakat (LPPM), IST AKPRIND Yogyakarta

Information technology and ielecommunications to the Internet becomes the main priority in the development of world progress. These developments provide new break-through in health care services mobile using mobile IT devices or socalled mobile doctor (m-doctor). M-doctor has some excess capacity for health care services that can be accessed anytime, anywhere, by anyone. The problems that still esist on still on m-doctor is that the lack of hardware and platforms that required by the system design and ease of access. One also needs a special study of each section dealing with the existing m-doctor in order to get comfortable for the user. The aim of this study is to address the issue by using streaming multimedia as content that can offer a more clear and specific infor-mation. Streaming multimedia services m-doctor require internet connection and good access, and also requires capable hardware to enjoy the overall bias with good services by using phones that support streaming multimedia mobile facilities. Expected results of this study is a software-based content cellular WCDMA, and the main target is to design m-doctor with streaming multimedia services.

OPTIMASI KOEFISIEN TRANSFER MASSA PADA EKSTRAKSI MINYAK BIJI KETAPANG Purwanti, Ani; -, Sumarni; -, Sugiyanto
JURNAL TEKNOLOGI TECHNOSCIENTIA Technoscientia Vol 2 No 2 Februari 2010
Publisher : Lembaga Penelitian & Pengabdian Kepada Masyarakat (LPPM), IST AKPRIND Yogyakarta

Mass transfer between solid and liquid is commonly found in extraction process. Oil extraction from catappa seeds was carried out in the stirred flask using normal hexane as a solvent. The aim of this research is to show a dimensionless equation of a Sherwood number {/} as a function both of Reynolds number {/} and Schimdt number {/}. The experiment was conducted in the room temperature, around 290C, stirring speed 500 rpm, blade diameter 2 cm, and the ratio between the mass of catappa seeds and the volume of solvent was 20 gr/100mLâ€“20 gr/200 mL. The calculation error was 0.072%. Based on the research, it is found that Sh = 0,2166.106 . Re-1,506. Sc1,120.

PEMODELAN ALIRAN DAYA PADA SISTEM ENERGI MOBIL LISTRIK Kaloko, Bambang Sri
JURNAL TEKNOLOGI TECHNOSCIENTIA Technoscientia Vol 2 No 2 Februari 2010
Publisher : Lembaga Penelitian & Pengabdian Kepada Masyarakat (LPPM), IST AKPRIND Yogyakarta

The issue of the depletion of oil reserves in the world, and the problem of air pollution produced by motor vehicles, motivate many researchers to seek alternative energy sources to propel the vehicle. One promising way is to replace combustion motor with an electric motor, which is known as an electric car. First stage of this research is to model the flow of power in the electric car energy system to obtain its characteristics. Power flow efficiency in electric cars is very important because this type of car is highly dependent on the limited electrical energy supplied by a battery. Therefore it should be managed properly. This study is to look into the power flow calculation so that the amount of electrical energy is in accordance with the needs of electric cars. A model using Simulink software is to get the best power flow response to the electric car energy system.

PENENTUAN JUMLAH PERSEDIAAN SUKU CADANG RANTAI GARU MESIN PENGGILING TEBU BERDASARKAN TINGKAT KEKRITISAN KOMPONEN MODEL ABC MENGGUNAKAN SPARE PART REQUIREMENT NOMOGRAPH Sodikin, Imam
JURNAL TEKNOLOGI TECHNOSCIENTIA Technoscientia Vol 3 No 1 Agustus 2010
Publisher : Lembaga Penelitian & Pengabdian Kepada Masyarakat (LPPM), IST AKPRIND Yogyakarta

Madukismo is one of the companies operating in the area of agroindustry with sugar as the main product. In order to exist, the company needs to increase the work effectiveness and efficiency in using the production machines through the planning of maintenance scheduling in order that the machines or units that are going to be used can be operated well, and work properly.The aim of this research is to analyze level requirement of amount of spare-part optimal with Sparepart requirement nomograph approach. This effort is able to increase high production quality, availability and reliability by maximizing equipments age, and also exploiting of effective maintenance. Based on the research result shows that the maintenance of chain eye component, it should be differentiated, basically, on the maintenance time. Determination of feed amounts at "t" periods with level of protection equal to 95% depict amount of requirement of accesses for chain component that availed counted 30 units.

KUALITAS BAKTERIOLOGI PADA DEPOT AIR MINUM ISI ULANG DI KOTA PONTIANAK TAHUN 2007 -, Suharno; Nasip, Muhammad; Iskandar, Dodi
JURNAL TEKNOLOGI TECHNOSCIENTIA Technoscientia Vol 2 No 2 Februari 2010
Publisher : Lembaga Penelitian & Pengabdian Kepada Masyarakat (LPPM), IST AKPRIND Yogyakarta

Based on the datas of health departement of Pontianak City, the Number of the refill drink water storehouse had been achieved 57. People as consumer of it have the right to get insurance of health and safety. Therefore there was needed to study bacte-riolgical test.This study was to get datas and to learn the coliform bacteriological contents of raw water and processed water on the refill drink water storehouse in Pontianak City. Raw water resource in Pontianak was 100 % derived from mountains. It covered 77.2 % of Anjungan, 12.3 % of Paniraman, 10.0 % of Sui Purun. It had Most Probable Coliform Number and Echericia Coli Number were 71.9 % and 59.6 % in sequence. These did not fulfill the requirements of health standard yet. Like wise, processed water of storehouse in Pontianak possessed 33.3 % of Most Probable Coliform Number and 15.4 % of E.Coli Number. The quality of raw water had significant coherence with Most Probable Coliform Number and Echericia Coli Number. Other factors that related to product of processed water quality were: The protection of raw water, disinfection processing, and water re-filling processing to plastic flask. Hence, the advice for processing manager of drinking water were to more taking a care the quality by disinfection pretreatment and protection. It was suggested for the health department to monitor and to evaluate continuesly at least every six months. It was recommended to people to choose selectively became customer of refill drinking water storehousers. Choose between them that had steril and saniter processing.

Page 22 of 59 | Total Record : 583

20 21 22 23 24

Filter by Year

2004 2024

Filter By Issues

All Issue Technoscientia Vol 17 No 1 September 2024 Technoscientia Vol 16 No 2 Maret 2024 Technoscientia Vol 16 No 1 September 2023 Technoscientia Vol 15 No 2 Maret 2023 Technoscientia Vol 15 No 1 September 2022 Technoscientia Vol 14 No 2 Maret 2022 Technoscientia Vol 14 No 1 Agustus 2021 Technoscientia Vol 13 No 2 Februari 2021 Technoscientia Vol 13 No 1 Agustus 2020 Technoscientia-Vol 13 No 1-Agustus 2020 Technoscientia Vol 12 No 2 Februari 2020 Technoscientia Vol 12 No 1 Agustus 2019 Technoscientia Vol 11 No 2 Februari 2019 Vol 10, No 2 (2018): Vol 10 No 2 Februari 2018 Technoscientia Vol 11 No 1 Agustus 2018 Vol 11, No 1 (2018): Technoscientia Vol 10 No 2 Februari 2018 Vol 10, No 1 (2017): Vol 10 No 1 Agustus 017 Vol 9, No 2 (2017): Vol 9 No 2 Februari 2017 Technoscientia Vol 10 No 1 Agustus 2017 Technoscientia Vol 9 No 2 Februari 2017 Technoscientia Vol 9 No 1 Agustus 2016 Technoscientia Vol 8 No 2 Februari 2016 Technoscientia Vol 8 No 1 Agustus 2015 Technoscientia Vol 7 No 2 Februari 2015 Technoscientia Vol 7 No 1 Agustus 2014 Technoscientia Vol 6 No 2 Februari 2014 Technoscientia Vol 6 No 1 Agustus 2013 Technoscientia Vol 5 No 2 Februari 2013 Technoscientia Vol 5 No 1 Agustus 2012 Technoscientia Vol 4 No 2 Februari 2012 Technoscientia Vol 4 No 1 Agustus 2011 Technoscientia Vol 3 No 2 Februari 2011 Technoscientia Vol 3 No 1 Agustus 2010 Technoscientia Vol 2 No 2 Februari 2010 Technoscientia Vol 2 No 1 Agustus 2009 Technoscentia Vol 1 No 2 Februari 2009 Academia Ista Vol 12 No 02 Februari 2008 Technoscentia Vol 1 No 1 Agustus 2008 Academia Ista Vol 12 No 01 Agustus 2007 Academia Ista Vol 11 Edisi Khusus Oktober 2006 Academia Ista Vol 10 Edisi Khusus September 2005 Academia Ista Vol 9 Edisi Khusus Oktober 2004 More Issue

Home Page

OAI Link

Editorial Team

Contact

Reviewer

Google Scholar

Contact Name
-

Contact Email
-

Phone
-

Journal Mail Official
-

Editorial Address
-

Location
Kota yogyakarta,

Daerah istimewa yogyakarta

INDONESIA

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Home Page

OAI Link

Editorial Team

Contact

Reviewer

Google Scholar

Contact Name -

Contact Email -

Phone -

Journal Mail Official -

Editorial Address -

Location Kota yogyakarta, Daerah istimewa yogyakarta INDONESIA

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Contact Name
-

Contact Email
-

Phone
-

Journal Mail Official
-

Editorial Address
-

Location
Kota yogyakarta,

Daerah istimewa yogyakarta

INDONESIA