cover
Contact Name
-
Contact Email
-
Phone
-
Journal Mail Official
majalahkkp@yahoo.co.id
Editorial Address
Balai Besar Kulit, Karet dan Plastik Jl. Sokonandi No. 9 Yogyakarta 55166
Location
Kota adm. jakarta selatan,
Dki jakarta
INDONESIA
Majalah Kulit, Karet, dan Plastik
ISSN : 18296971     EISSN : 24604461     DOI : 10.20543
Core Subject : Engineering,
Majalah Kulit, Karet, dan Plastik (Journal of Leather, Rubber, and Plastics) publishes original research focused on materials, processes, and waste management in the field of leather, rubber, and plastics.
Articles 781 Documents
Pengaruh kadar krom limbah lumpur industri penyamakan kulit terhadap pertumbuhan dan hasil tanaman sawi A. R. Budi Darmawan
Majalah Kulit, Karet, dan Plastik Vol 26, No 1 (2010): Majalah Kulit, Karet, dan Plastik
Publisher : Center for Leather, Rubber, and Plastic Ministry of Industry, Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (2383.191 KB) | DOI: 10.20543/mkkp.v26i1.241

Abstract

The aim of the experiment was to study the effect of chrom content of leather tanning industry waste ti the growth and yield of mustards. The experiment used factorial design 2x3 factors, and 2 control were used and the treatments were arranged in a complete randomized design with 15 experimental pots for replication. The first factor was variety of mustard; consisting of 2 kinds, i,e, green mustard (caisim) dan bitter mustard (leaf mustard). The second factor was the amount of leather tanning industrial waste, consisting of 3 levels, i.e.500, 1000 and 1500 mg/kg Cr/polybag (125,250, 375 g waste mud/polybag). Waste mud was added in the polybag after 1 week plantation. Controls were madewith code S1L1C0, S2L1C0 whereas L1C0 = without waste mud added. The observed parameters were plant height, leaf number, fresh weight (shoots-roots), dry weight (shoots-roots), leaf area, neg assimilation rate, relative growth rate and leaf area ratio. The results showed that there were interactions between varieties of mustard and the amount of leather tanning industrial waste for all parameters. The addition of leather tanning waste until 1000 mg/kg soil gave fine growth and yields for all mustard varieties.  Keywords : chromium, leather tanning industrial waste, mustards.   Penelitian bertujuan untuk mempelajari pengaruh kadar krom limbah lumpur industry penyamakan kulit terhadap pertumbuhan dan hasil tanaman sawi. Percobaan menggunakan rancangan factorial 2 x 3 lengkap dan 2 perlakuan tambahan sebagai control yang diatur dalam Rancangan Acak Lengkap (RAL), dengan 15 unit polybag sebagai ulangan. Factor pertama terdiri dari 2 varietas sawi, yaitu sawi hijau (caisim) dan sawi pahit (leaf mustard). Factor kedua terdiri atas 3 aras takaran limbah lumpur industry penyamakan kulit, yaitu dengan kadar krom 500 mg/kg tanah (setara dengan 25 g limba lumpur/kg media tanah)m 1000 mg krom/kg tanah (setara dengan 50 g limbah lumpur/kg media tanah), 1500 mg krom/kg tanah (setara dengan 75 g limbah lumpur / kg media tanah). Limbah lumpur ditambahkan ke media tanah dalam polybag setelah 1 minggu bibit sawi dipindah ke polybag tanam.  Dibuat control dengan kode S1L1C0, S2L1C0 dimana L1C0 = tanpa ditambah limbah lumpur.  Pengamatan dilakukan terhadap pertumbuhan dan perkembangan tanaman meliputi tinggi tanaman,  jumlah daun, berat segar tanman (tajuk dan akar), berat kering tanaman (tajuk dan akar), luas daun, laju asimilasi bersih, laju pertumbuhan nisbi dan nisbah luas daun. Hasil penelitian menunjukkan terdapat interaksi antara jenis sawi, dan jumlah takaran limbah lumpur untuk semua parameter pertumbuhan dan hasil tanaman. Perlakuan pemberian limbah lumpur sebesar 1000 mg krom/kg tanah masih memberikan pertumbuhan dan hasil yang baik terhadap semua jenis sawi. Kata Kunci : kromium, limbah industri penyamakan kulit, sawi. 
Pengaruh penambahan karet siklo terhadap sifat vulkanisat kompon karpet karet Dwi Wahini Nurhajati; Ary Achyar Alfa
Majalah Kulit, Karet, dan Plastik Vol 23, No 1 (2007): Majalah Kulit, Karet, dan Plastik
Publisher : Center for Leather, Rubber, and Plastic Ministry of Industry, Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (506.959 KB) | DOI: 10.20543/mkkp.v23i1.325

Abstract

Effect of cyclis rubber on the vulcanizate properties of fubber carpet compound was investigated. Carpet compounds were prepared by ribbed smoked sheets I (RSS I) and styrene butadiene rubber (SBR) as a raw material, and cyclis rubber in various amount was added as additive. The amounts of the added cyclis rubber were varied from 10 to 40 phr with range of 10 phr. The rubber carpet compound was produced by using a two roll-mills (Shanghai RMW, model XK-160, capacity 2 kg). The culcanizate properties of rubber carpet compound were tested base on SNI. 12-1000-1989 for karpet karet, and ASTM F.1859-2000 for rubber sheet floor covering without backing The results showed that cyclis rubber in the compound was focused as a filler. Generally, the physical properties of vulcanizates containing cyclis rubber was better than the vulcanizates without cyclis rubber. Effects of cyclis rubber on the vulcanize properties of rubber carpet compound have increase hardness, tensile strength elongation at break, dimensional stability, and slip resistance. The compound with ratio of cyclis rubber 10 phr performed the best physical properties i.e: 85 Shore A hardness, 1479.9 N/cm2 tensile strength, 372.44% elongation at break, 1.24 g/cm3 density, 433.33 N/cm2 compression resistance, 2.29 mm3/kg.m Graselli abrasion resistance, and 1.24 U coefficient slipping resistance on dry surface, respectively.  Keywords: cyclis rubber, rubber carpet compound. ABSTRAK Telah dilakukan penelitian mengenai pengaruh karet siklo yang merupakan produk modifikasi karet alam terhadap sifat vulkanisat kompon karpet karet. Kompon karpet karet dibuat dengan bahan baku karet asap lembaran (RSS) dan karet sintetis styrene butadiene (SRB), dan karet siklo sebagai aditif. Karet siklo yang ditambahkan jumlahnya divariasi dari 10 – 40 phr dengan kisaran kenaikan 10 phr. Pembuatan kompon karpet menggunakan alat two rolls-mills (Shanghai RMW, model XK-160, kapasitas 2 kg). Sifat fisis kompon karpet karet diuji berdasar SNI.12-1000-1989 untuk karpet karet maupun ASTM F.1859-2000 untuk rubber sheet floor covering without backing. Hasil penelitian menunjukkan bahwa karet siklo pada pembuatan karpet karet berfungsi sebagai bahan pengisi. Secara umum sifat fisis vulkanisat yang berisi karet siklo lebih baik daripada vulkanisat tanpa karet siklo. Karet siklo terbukti meningkatkan kekerasan, tegangan putus, perpanjangan putus, 372,44%, kerapatan massa 1,24 gr/cm3, ketahanan pampat 433,22 N/cm2, ketahanan kikis (Grasselli) 2,29 mm3/kg. m, dan ketahanan slip pada permukaan kering 1,24 koefisien U. Kata kunci: karet siklo, kompon karpet karet.
Pengaruh kombinasi bahan penyamak formalin dan syntan terhadap kualitas kulit ikan pari tersamak Latif Sahubawa; Ambar Pertiwiningrum; Adityo Triarso Pamungkas
Majalah Kulit, Karet, dan Plastik Vol 27, No 1 (2011): Majalah Kulit, Karet, dan Plastik
Publisher : Center for Leather, Rubber, and Plastic Ministry of Industry, Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (2887.051 KB) | DOI: 10.20543/mkkp.v27i1.211

Abstract

abstrak
Peningkatan kualitas air limbah terolah industri penyamakah kulit menggunakan taman tanaman air dengan tumbuhan bambu air Prayitno Prayitno; Muhammad Sholeh
Majalah Kulit, Karet, dan Plastik Vol 30, No 1 (2014): Majalah Kulit, Karet, dan Plastik
Publisher : Center for Leather, Rubber, and Plastic Ministry of Industry, Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (894.781 KB) | DOI: 10.20543/mkkp.v30i1.120

Abstract

A research of constructed wetland system vegetated with Equisetum hyemale for treating of treated tannery wastewater have been conducted. The constructed wetland was 3 m long, 1 m wide, and 1 m deep or equal with volume of 3 m3. The construction of wetland consisted of 4 main layers (from the bottom to the top): 0.3 m of rock; 0.3 m of gravel; 0.1 m of black sugar-palm fiber; and 0.3 m of sand. The wetland was operated with subsurface flow system (SSF). The detention time was varied at 3.125; 2.083; and 1.563 days. The result showed that the optimum removal were 60.60% for COD with detention time of 3.125 days, 60.17% for BOD with detention time of 2.083 days, 93.76% for TSS with detention time of 3.125 days, 89.02%  for S with detention time of 3.125 days and 96.89% for total chrome wth detention time of 2.083 days.ABSTRAKTelah dilakukan penelitian taman tanaman air (TTA) dengan tanaman bambu air untuk mengolah limbah cair terolah industri penyamakan kulit. Konstruksi TTA berukuran panjang 3 m, lebar 1 m, dan dalam 1 m, atau sama dengan volume 3 m3. Media terdiri atas empat lapisan mulai dari bawah adalah koral 0,3 m, kerikil 0,3 m, ijuk 0,1 m, dan lapisan paling atas adalah pasir 0,3 m. TTA dioperasikan dengan sistem aliran subsurface (SSF). Waktu tinggal divariasi berturut-turut pada 3,125; 2,083; dan 1,563 hari. Hasil penelitian menunjukan efektivitas penurunan COD sebesar 60,60% dengan waktu tinggal 3,125 hari, penurunan BOD sebesar 60,17% dengan waktu tinggal 2,083 hari, penurunan TSS sebesar 93,76% dengan waktu tinggal 3,125 hari, penurunan S sebesar 89,02% dengan waktu tinggal 3,125 hari dan penurunan krom sebesar 96,89% dengan waktu tinggal 2,083 hari.
Pengolahan air limbah industri penyamakan kulit menggunakan abu terbang bagas secara batch Muhammad Sholeh; Agus Prasetya; Sarto Sarto
Majalah Kulit, Karet, dan Plastik Vol 28, No 1 (2012): Majalah Kulit, Karet, dan Plastik
Publisher : Center for Leather, Rubber, and Plastic Ministry of Industry, Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (237.709 KB) | DOI: 10.20543/mkkp.v28i1.202

Abstract

The objective of this research was to evaluate the adsorption ability of chemically activated bagasse fly ash using H O or H SO to remove COD from tannery wastewater and to obtain 2 adsorption isotherm model in batch system. Two stages have been carried out, namely the activation experiment and the adsorption isotherm experiment. In the activation experiment, effect of H O dan H SO (3% and 7,5% w/w) were studied. The best result of the variation was used in the next experiment. In the adsorption isotherm experiment, variation of the initial concentrations of COD from 52,53 to 1665,79 mg/L and mass of bagasse fly ash from 0,1 to 0,4 g were used. Equilibrium data was used to evaluate the parameters in the Langmuir, Freundlich, and Temkin equations. The best model was evaluated using determination coefficients. The results showed that bagas fly ash had better ability to reduce the COD when it was not activated with H O nor H SO (3% and 7,5%). Freundlich model was best to describe COD removal using bagasse fly ash in batch system. Freundlich equation constants K and n were F 0,4360 (mg/g)/(L/mg)1/n and 1,2969 respectively and the determination coefficient obtained was 0,93.  Keywords: Chemical Oxygen Demand, tannery wastewater, bagasse fly ash, adsorption
Pengaruh penggunaan lumpur limbah industri penyamakan kulit terhadap penyerapan krom pada tanaman sawi A. R. Budi Darmawan
Majalah Kulit, Karet, dan Plastik Vol 28, No 2 (2012): Majalah Kulit, Karet, dan Plastik
Publisher : Center for Leather, Rubber, and Plastic Ministry of Industry, Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (572.581 KB) | DOI: 10.20543/mkkp.v28i2.107

Abstract

ABSTRACTThe aims of research was to study the effect of contaminated soil with tannery industrial wastesludge, and absorption level of chromium by the green mustard. The experiment was carried out in Kayen, Sleman, Yogyakarta for 3 months. The form of a pot experiment using a full factorial design 2x3 and 2 additional treatments as a control was set out in Completely Randomized Design (CRD), using 15 units of pots as replicates. The first factor consists of two varieties of mustard, which is kailan (chinesse kale) and spoon mustard greens (pak choy green). The second factor consists of 3 doses of leather tanning industry waste, i.e 500 mg chromium/kg soil, 1000 mg chromium/kg soil, 1500 mg chromium/kg soil. Control treatment was the planting of two varieties of mustard without the addition of sewage sludge. Preparation of sewage sludge was carried out by mixing the sewage sludge into the planting medium consisting of a mixture of soil, compost and manure treatments in accordance with the treatment. Observations made by harvesting the plants at the age of 3 and 6 weeks after planting for the next shoots and roots of plants and chromium content of growing media was analyzed. The results showed that the accumulation of chromium in the roots of plants was greater than in the plant canopy for the two types of mustards either good harvested at the age of 3 or 6 weeks after planting, and the content of chromium in plant tissues of mustard as part of vegetable that generally consumed exceeds the threshold of human daily consumption (0,035 mg/kg daily consumption). ABSTRAKPenelitian bertujuan untuk mempelajari pengaruh tanah yang terkontaminasi limbah industri penyamakan kulit terhadap sifat dan tingkat penyerapan krom pada tanaman sawi. Penelitian dilaksanakan di Kayen, Sleman, Daerah Istimewa Yogyakarta selama 3 bulan. Percobaan dengan pot menggunakan rancangan faktorial 2x3 lengkap dan 2 perlakuan tambahan sebagai kontrol yang diatur dalam Rancangan Acak Lengkap (RAL), dengan 15 unit pot sebagai ulangan percobaan. Faktor pertama terdiri atas 2 varietas sawi, yaitu kailan (chinesse kale) dan sawi sendok (pak choy green). Faktor kedua terdiri atas 3 aras takaran limbah industri penyamakan kulit, yaitu 500 mg krom/kg tanah, 1000 mg krom/kg tanah, 1500 mg krom/kg tanah. Perlakuan kontrol adalah penanaman 2 varietas sawi tanpa pemberian lumpur limbah. Pemberian limbah dilakukan dengan mencampur lumpur limbah ke dalam media tanam yang terdiri atas campuran tanah, kompos dan pupuk kandang sesuai dengan variasi perlakuan. Pengamatan dilakukan dengan memanen tanaman saat umur 3 dan 6 minggu setelah tanam untuk selanjutnya tajuk dan akar tanaman serta media tanam dianalisa kandungan kromnya. Hasil penelitian menunjukkan bahwa akumulasi krom di bagian perakaran tanaman lebih besar dibandingkan di bagian tajuk tanaman untuk kedua jenis sawi baik pada umur panen 3 maupun 6 minggu setelah tanam ternyata kandungan krom dalam jaringan tanaman sawi bagian tajuk yang lazim dikonsumsi melebihi ambang batas konsumsi harian manusia yang ditetapkan sebesar 0,035 mg/kg per hari.
Pemanfaatan zeolit sebagai bahan pengisi dalam pembuatan karet sponge untuk tatakan sepatu Herminiwati Herminiwati; Murwati Murwati; Sri Brataningsih Puji Lestari
Majalah Kulit, Karet, dan Plastik Vol 23, No 1 (2007): Majalah Kulit, Karet, dan Plastik
Publisher : Center for Leather, Rubber, and Plastic Ministry of Industry, Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (759.686 KB) | DOI: 10.20543/mkkp.v23i1.334

Abstract

The purpose of this research was to study the effect of zeolite as filler in the preparation of sponge rubber for shoe insocks. During wearing period of shoes, unpleasant odor often smell for the result of sweat accumulation and their decomposition by microorganism. Besides as rubber filler, zeolit has odor adsorption function. The formula of rbber sponge could be as the following : crepe rubber 100 phr, paraffinic oil 20 phr, ZnO 10 phr, stearic acid 5 phr, MBTS 1 phr, TMTD 0.25 phr, anti-oxidant 1 phr and sulphur 2 phr. To obtain the best sponge rubber formula, some experiment was done by formulating variation of zeolite and blowing agent AZDM in the amount of 25, 50, 75 phr and 5, 10, 15 phr respectively. The vulcanization process was carried-out at temperature 140oC for minutes by compression moulding. The research showed that the best formula with high odor absorption was consist of zeolite 50 phr and blowing agent AZDM 5 phr. The sponge rubber had odor adsorption 93,47%, and the physical properties were as follow: tensile strength 2.018 N/mm2, elongation at break 251%, tear strength 1.029 N/mm2, density 0.717 g/cm3, and compression set 36.38%. Odor absorption was tested by using gas chromatography. Key words : zeolite,filler, sponge, rubber, shoe insocks. ABSTRAKPenelitian ini bertujuan untuk mempelajari pengaruh penggunana zeolit sebagai bahan pengisi dalam pembuatan karet sponge untuk tatakan sepatu. Pada pemakaian sepatu seringkali timbul bau tak sedap karena akumulasi keringat dan perurainnya oleh mikroorganisme. Zeolit selain sebagai bahan pengisi karet juga berfungsi sebagai peneyrap bau. Formula karet sponge terdiri atas karet krep 100 phr, minyak parafinik 20 phr, ZnO 10 phr, asam stearat 5 phr, MBTS 1 phr, TMTD 0,25 phr, anti oksidan 1 phr, belerang 2 phr. Untuk mendapatkan formula karet sponge terbaik maka peneltiian dilakukan dengan variasi bahan pengisi zeolit sebesar 25,50, 75 phr dan bahan pengembang AZDM sebesar 5, 10, 15 phr. Vulkanisasi dilakukan pada suhu 140 oC selama 10 menit dengan proses cetak tekan. Hasil penelitian menunjukkan bahwa formula terbaik dengan daya serap bau tinggi terdiri atas zeolit 50 phr dan bahan pengembang 5 phr. Karet sponge mempunyai daya serap bau 93,47% dan sifat fisis sebagai berikut: tegangan putus 2,018 N/mm2, perpanjangan putus 521%, ketahanan sobek 1,029 N/mm2, bobot jenis 0,717 g/cm3, pampat tetap 36,38%. Daya serap bau diuji menggunakan gas kromatografi. Kata kunci : zeolit, bahan pngisi, karet sponge, tatakan sepatu
Kajian penerapan recycle, reuse dan recovery untuk proses produksi kulit web blue pada industri penyamakan kulit Prayitno Prayitno
Majalah Kulit, Karet, dan Plastik Vol 25, No 1 (2009): Majalah Kulit, Karet, dan Plastik
Publisher : Center for Leather, Rubber, and Plastic Ministry of Industry, Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (2715.965 KB) | DOI: 10.20543/mkkp.v25i1.232

Abstract

Leather tanning industries are industries that process skin to produce finish leather product by using many stages of process in which for every stage of process will generate a huge amount either liquid or solid waste. If waste are not to be treated properly, it will cause environmental pollution. Implementation of 3R programs i.e. recycle, reuse and recovery will give impact on minimizing of waste problem. In leather tanning industries for producing wet blue leather however, 3R programs have to be implemented in processes of desalting, washing liquor, flesh and fat, chrome liquor and chrome-tanned waste. In implementing 3 R the waste generated can be either reused, recycled or recoveried as follow salt as swelling agent preventing in pickling process; washing liquor waste as washing liquor for dirt washing; flesh and fat as raw material for producing tallow, soap, fertilizer and livestock fodder; chrome liquor waste as chrome agent for chrome tanning and chrome-tanned waste as filler for producing material building or livestock fodder as protein sources. Keywords: tanning, 3R, waste, environment  ABSTRAK Industri penyamakan kulit adalah industri yang mengolah kulit mentah menjadi kulit tersamak. Pengolahan bahan baku kulit menjadi kulit tersamak dilakukan melalui beberapa tahap proses, dan setiap tahap proses dipastikan membuang limbah dan jika tidak diolah dengan tepat dan baik dapat mencemari lingkungan. Penerapan program 3 R (Reuse, Recycle, dan Recovery) dimaksudkan untuk memakai ulang, mendaur ulang, dan memungut ulang limbah dari setiap tahap agar limbah yang terbentuk dapat dikurangi atau ditiadakan. Program 3 R pada pembuatan kulit “wet blue” dapat dilakukan pada setiap tahap yang terdiri atas penanganan bahan baku di gudang, perendaman dan pencucian, pemisahan daging, penyamakan dan penyerutan, limbah yang ditimbulkan dari tahapan proses tersebut dapat dalam bentuk garam, air cucian, daging sisa dan lemak, larutan krom dan serutan kulit tersamak. Untuk penerapan program 3 R garam dapat didaur ulang untuk mencegah pembengkakan kulit pada proses pengasaman, bekas air cucian dapat digunakan kembali untuk pencucian tahap awal, daging sisa dan lemak dapat dipungut ulang untuk pembuatan lemak, sabun, pupuk dan makanan ternak, larutan krom dapat di pungut ulang senyawa krom untuk proses penyamakan ulang, sedang serutan kulit tersamak dapat dipungut ulang untuk material bangunan atau sumber protein untuk makanan ternak. Kata kunci: penyamakan, 3 R, limbah, lingkungan
Pengaruh rss/sbr dan filler CaCO3 terhadap sifat fisis kompon karpet karet Supraptiningsih Supraptiningsih; Sri Brataningsih Puji Lestari
Majalah Kulit, Karet, dan Plastik Vol 21, No 1 (2005): Majalah Kulit, Karet, dan Plastik
Publisher : Center for Leather, Rubber, and Plastic Ministry of Industry, Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (774.569 KB) | DOI: 10.20543/mkkp.v21i1.316

Abstract

Research about preparing of rubber compound for carpet has been done. The aim of this research to study the effects of natural rubber RSS and CaCO3 as a filler, its physical properties, and also to find out rubber compound for carpet formula in accordance with SNI 12-1000-1989. The compound was produced from natural and synthetic rubber mixture with variation of RSS/SBR 70/30; 80/20; 90/10 phr respectively and the amount of CaCO3 90; 100; 110 phr respectively. The compound was made by using two roll mill machine and than it was tested the physical properties by methods of SNI 12-1000-1989 Rubber Carpet. The physical properties of compound showed that an increasing of natural rubber (RSS I) significant enfluence to increase elongation from 420,00% until 466,66% while hardness from 69,11 shore A until 68,11 sore A, and compression resistance decrease from 580,42% N/cm2 until 523,20 N/cm2. The addition of CaCO3 very significant enfluence to increase hardness from 65,77 shore A until 71,83 shore A, permanent set from 482,32 N/cm2, and the density from 1,48 g/cm2 until 1,55 g/cm2. The physical properties of elongation decrease from 464,44 % until 406,66 % and the aging resistance decrease too (colour changing and cracked). The rubber compound for carpet was produced by using RSS/SBR 80/20 and added CaCO3 100 phr accordance with SNI 12-1000-1989 and significant difference with the others.  Keywords : rubber compound, filler, carpet.   ABSTRAK Telah dilakukan penelitian tentang pembuatan kompon karet untuk karpet. Tujuan penelitian adalah mengamati pengaruh penggunaan karet alam RSS dan pengaruh CaCO3 sebagai bahan pengisi terhadap sifat fisis karpet karet, serta mencari formulasi kompon karet untuk karpet yang memenuhi persyaratan  SNI 12-1000-1989. Kompon karet dibuat dari campuran karet alam (RSS I) dan karet sintetis (SBR) dengan variasi perbandingan RSS / SBR berturut-turut 70/30; 80/20; dan 90/10 phr serta variasi CaCO3 90 ; 100 dan 110 phr. Kompon karet dibuat menggunakan mesin two roll mill dan kemudian diuji sifat fisisnya sesuai dengan metode SNI 12-1000-1989 Karpet Karet. Hasil pengujian sifat fisis menunjukkan bahwa penambahan karet alam (RSS I) dapat berpengaruh nyata menaikkan sifat perpanjangan putus dari 420,00 % menjadi 466,66%,  sedangkan kekerasan turun dari 69,11 shore A menjadi 68,11 shore A, dan ketahanan pampat turun dari 580,42 N/cm2 menjadi 523,20 N/cm2. Penambahan CaCO3 berpengaruh sangat nyata menaikkan sifat kekerasan yaitu dari 65,77 shore A menjadi 71,83 shore A, ketahanan pampat dari 482,32 N/cm2 menjadi 596,74 N/cm2, dan kerapatan massa dari 1,48 g/cm2 menjadi 1,55 g/cm2. Sifat perpanjangan putus menurun dari 464,44% menjadi 406,66% dan ketahanan terhadap pengusangan juga menurun (terjadi perubahan warna dan menjadi retak). Hasil kompon karet untuk karpet yang memenuhi persyaratan SNI 12 – 1000- 1989 adalah karpet yang dibuat dengan RSS/SBR 80/20 dan CaCO3 100 phr yang berbeda nyata dengan yang lain.  Kata Kunci : kompon karet, bahan pengisi, karpet. 
Pengaruh tingkat protein dan energi pakan terhadap kualitas kulit untuk atasan sepatu dari kelinci rex jantan Sri Untari; Soediman Sastrodihardjo
Majalah Kulit, Karet, dan Plastik Vol 10, No 20 (1995): Majalah Barang Kulit, Karet, dan Plastik
Publisher : Center for Leather, Rubber, and Plastic Ministry of Industry, Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1371.575 KB) | DOI: 10.20543/mkkp.v10i20.443

Abstract

This research intends to know the effect of fodder protein and energy level on the physical test (i.e. the elasticity, tensile strength and tear strength) of Rex rabbit leather, the raw material of shoe upper. The materials for research are 27 skin of dried 12-to-13-month-old male Rex rabbit. The complete random research design is used here with the factor pattern 3 X 3 = 9 kinds of combination of treatment factors,i.e. the factors or three levels of protein :15% n(P1), 17% (P2), and 19% (P3); the factors of three levels of digestible energy (D) : 2,000 kcal/kg (D1), 2,250 kcal.kg (D2), and 2,500 kcal/kg; and three skins of dried rabbit leathers in each treatment as replication. The parameter of the physical test will be determined with the covariance analysis, with the thickness of the leathers as a coverable. When the F analysis gives the result that are perceptibly different, it is followed by the “Least Significant Difference (LSD) analysis. The results of the research are that protein and ‘digestible energy’ have an imperceptibly different effect (P > 0.005) on the elasticity, tensile strength, and tear-trength of the charm tanned and than the thickness of the effect (P > 0.05) on the thickness of the leathers and a linear regression relation, but it does not it the physical-testing.     INTISARI              Penelitian ini bertujuan untuk mengetahui pengaruh tingkat protein dan energi pakan terhadap kualitas fisis mencakup itu kemuluran, kekuatan tarik dan kekuatan sobek kulit jadi dari kelinci Rex dalam upaya penyediaan bahan baku kulit untuk atasan sepatu. Materi penelitian ini menggunakan sejumlah 27 lembar kulit kering yang berasal dari 27 ekor kelini Rex jantan berumur antara 12-13 bulan. Rancangan penelitian ini menggunakan rancangan acak lengkap pola                factorial 3 X 3 = 9 macam kombinasi factor perlakuan yakni 3 faktor tingkat protein 15% (P!), 17% (P2) dan 19% (P3) ; dan tiga tingkat “digestible energy (D)” 2.00 kcal/kg (D1), 2.250 kcal/kg (D2) dan 2.500 kcal/kg pakan (D3), masing-masing perlakuan menggunakan 3 lembar kulit kering yang berasal dari 3 ekor kelinci sebagai ulangan. Parameter kualitas fisis dianalisis covariansi dengan tebal kulit sebagai covarianble. Apabila uji F berbeda nyata dilanjutkan dengan uji “Least Defference (LSD)”. Hasil penelitian menunjukan bahwa pengaruh protein dan “degistible energy” berpengaruh tidak berbeda nyata (P > 0,05) terhadap kualitas kemuluran, kekuatan tarik, kekuatan sobek kulit samak krom . Tebal kulit dipakai sebagai factor cavariable dalam analisa covarian menunjukkan berpengaruh beda nyata (P < 0,05) tehadap kekuatan sobek dan mempunyai hubungan regresi linear < tetapi terhadap uji kualitas fisis berpengaruhtidak berbeda nyata.

Filter by Year

1984 2021


Filter By Issues
All Issue Vol 37, No 2 (2021): Majalah Kulit, Karet, dan Plastik Vol 37, No 1 (2021): Majalah Kulit, Karet, dan Plastik Vol 36, No 2 (2020): Majalah Kulit, Karet, dan Plastik Vol 36, No 1 (2020): Majalah Kulit, Karet, dan Plastik Vol 35, No 2 (2019): Majalah Kulit, Karet, dan Plastik Vol 35, No 1 (2019): Majalah Kulit, Karet, dan Plastik Vol 34, No 2 (2018): Majalah Kulit, Karet, dan Plastik Vol 34, No 1 (2018): Majalah Kulit, Karet dan Plastik Vol 33, No 2 (2017): Majalah Kulit, Karet, dan Plastik Vol 33, No 2 (2017): Majalah Kulit, Karet, dan Plastik Vol 33, No 1 (2017): Majalah Kulit, Karet, dan Plastik Vol 33, No 1 (2017): Majalah Kulit, Karet, dan Plastik Vol 32, No 2 (2016): Majalah Kulit, Karet, dan Plastik Vol 32, No 2 (2016): Majalah Kulit, Karet, dan Plastik Vol 32, No 1 (2016): Majalah Kulit, Karet, dan Plastik Vol 32, No 1 (2016): Majalah Kulit, Karet, dan Plastik Vol 31, No 2 (2015): Majalah Kulit, Karet, dan Plastik Vol 31, No 2 (2015): Majalah Kulit, Karet, dan Plastik Vol 31, No 1 (2015): Majalah Kulit, Karet, dan Plastik Vol 31, No 1 (2015): Majalah Kulit, Karet, dan Plastik Vol 30, No 2 (2014): Majalah Kulit, Karet, dan Plastik Vol 30, No 2 (2014): Majalah Kulit, Karet, dan Plastik Vol 30, No 1 (2014): Majalah Kulit, Karet, dan Plastik Vol 30, No 1 (2014): Majalah Kulit, Karet, dan Plastik Vol 29, No 2 (2013): Majalah Kulit, Karet, dan Plastik Vol 29, No 2 (2013): Majalah Kulit, Karet, dan Plastik Vol 29, No 1 (2013): Majalah Kulit, Karet, dan Plastik Vol 29, No 1 (2013): Majalah Kulit, Karet, dan Plastik Vol 28, No 2 (2012): Majalah Kulit, Karet, dan Plastik Vol 28, No 2 (2012): Majalah Kulit, Karet, dan Plastik Vol 28, No 1 (2012): Majalah Kulit, Karet, dan Plastik Vol 28, No 1 (2012): Majalah Kulit, Karet, dan Plastik Vol 27, No 1 (2011): Majalah Kulit, Karet, dan Plastik Vol 27, No 1 (2011): Majalah Kulit, Karet, dan Plastik Vol 26, No 1 (2010): Majalah Kulit, Karet, dan Plastik Vol 26, No 1 (2010): Majalah Kulit, Karet, dan Plastik Vol 25, No 1 (2009): Majalah Kulit, Karet, dan Plastik Vol 25, No 1 (2009): Majalah Kulit, Karet, dan Plastik Vol 24, No 1 (2008): Majalah Kulit, Karet, dan Plastik Vol 24, No 1 (2008): Majalah Kulit, Karet, dan Plastik Vol 23, No 1 (2007): Majalah Kulit, Karet, dan Plastik Vol 23, No 1 (2007): Majalah Kulit, Karet, dan Plastik Vol 22, No 1 (2006): Majalah Kulit, Karet, dan Plastik Vol 22, No 1 (2006): Majalah Kulit, Karet, dan Plastik Vol 21, No 1 (2005): Majalah Kulit, Karet, dan Plastik Vol 21, No 1 (2005): Majalah Kulit, Karet, dan Plastik Vol 20, No 1 (2004): Majalah Kulit, Karet, dan Plastik Vol 20, No 1 (2004): Majalah Kulit, Karet, dan Plastik Vol 19, No 1 (2003): Majalah Kulit, Karet, dan Plastik Vol 19, No 1 (2003): Majalah Kulit, Karet, dan Plastik Vol 18, No 1 (2002): Majalah Barang Kulit, Karet, dan Plastik Vol 18, No 1 (2002): Majalah Barang Kulit, Karet, dan Plastik Vol 17, No 1-2 (2001): Majalah Barang Kulit, Karet, dan Plastik Vol 17, No 1-2 (2001): Majalah Barang Kulit, Karet, dan Plastik Vol 14, No 26 (1999): Majalah Barang Kulit, Karet, dan Plastik Vol 14, No 26 (1999): Majalah Barang Kulit, Karet, dan Plastik Vol 15, No 2 (1999): Majalah Barang Kulit, Karet, dan Plastik Vol 15, No 2 (1999): Majalah Barang Kulit, Karet, dan Plastik Vol 12, No 25 (1998): Majalah Barang Kulit, Karet, dan Plastik Vol 12, No 25 (1998): Majalah Barang Kulit, Karet, dan Plastik Vol 12, No 24 (1997): Majalah Barang Kulit, Karet, dan Plastik Vol 12, No 24 (1997): Majalah Barang Kulit, Karet, dan Plastik Vol 12, No 23 (1997): Majalah Barang Kulit, Karet, dan Plastik Vol 12, No 23 (1997): Majalah Barang Kulit, Karet, dan Plastik Vol 12, No 22 (1996): Majalah Barang Kulit, Karet, dan Plastik Vol 12, No 22 (1996): Majalah Barang Kulit, Karet, dan Plastik Vol 11, No 21 (1996): Majalah Barang Kulit, Karet, dan Plastik Vol 11, No 21 (1996): Majalah Barang Kulit, Karet, dan Plastik Vol 10, No 20 (1995): Majalah Barang Kulit, Karet, dan Plastik Vol 10, No 20 (1995): Majalah Barang Kulit, Karet, dan Plastik Vol 10, No 19 (1995): Majalah Barang Kulit, Karet, dan Plastik Vol 10, No 19 (1995): Majalah Barang Kulit, Karet, dan Plastik Vol 9, No 18 (1994): Majalah Barang Kulit, Karet, dan Plastik Vol 9, No 18 (1994): Majalah Barang Kulit, Karet, dan Plastik Vol 9, No 17 (1994): Majalah Barang Kulit, Karet, dan Plastik Vol 9, No 17 (1994): Majalah Barang Kulit, Karet, dan Plastik Vol 9, No 16 (1994): Majalah Barang Kulit, Karet, dan Plastik Vol 9, No 16 (1994): Majalah Barang Kulit, Karet, dan Plastik Vol 7, No 12-13 (1992): Majalah Barang Kulit, Karet, dan Plastik Vol 7, No 12-13 (1992): Majalah Barang Kulit, Karet, dan Plastik Vol 8, No 15 (1992): Majalah Barang Kulit, Karet, dan Plastik Vol 8, No 15 (1992): Majalah Barang Kulit, Karet, dan Plastik Vol 8, No 14 (1992): Majalah Barang Kulit, Karet, dan Plastik Vol 8, No 14 (1992): Majalah Barang Kulit, Karet, dan Plastik Vol 6, No 10-11 (1991): Majalah Barang Kulit, Karet, dan Plastik Vol 6, No 10-11 (1991): Majalah Barang Kulit, Karet, dan Plastik Vol 5, No 9 (1990): Majalah Barang Kulit, Karet, dan Plastik Vol 5, No 9 (1990): Majalah Barang Kulit, Karet, dan Plastik Vol 4, No 8 (1989): Majalah Barang Kulit, Karet, dan Plastik Vol 4, No 8 (1989): Majalah Barang Kulit, Karet, dan Plastik Vol 3, No 7 (1988): Majalah Barang Kulit, Karet, dan Plastik Vol 3, No 7 (1988): Majalah Barang Kulit, Karet, dan Plastik Vol 3, No 6 (1988): Majalah Barang Kulit, Karet, dan Plastik Vol 3, No 6 (1988): Majalah Barang Kulit, Karet, dan Plastik Vol 2, No 5 (1987): Majalah Barang Kulit, Karet, dan Plastik Vol 2, No 5 (1987): Majalah Barang Kulit, Karet, dan Plastik Vol 2, No 3-4 (1986): Majalah Barang Kulit, Karet, dan Plastik Vol 2, No 3-4 (1986): Majalah Barang Kulit, Karet, dan Plastik Vol 1, No 2 (1984): Majalah Barang Kulit, Karet, dan Plastik Vol 1, No 2 (1984): Majalah Barang Kulit, Karet, dan Plastik Vol 1, No 1 (1984): Majalah Barang Kulit, Karet, dan Plastik Vol 1, No 1 (1984): Majalah Barang Kulit, Karet, dan Plastik More Issue