cover
Contact Name
Syafii
Contact Email
jnte@ft.unand.ac.id
Phone
-
Journal Mail Official
Syafii@ft.unand.ac.id
Editorial Address
-
Location
Kota padang,
Sumatera barat
INDONESIA
JURNAL NASIONAL TEKNIK ELEKTRO
Published by Universitas Andalas
ISSN : 23022949     EISSN : 24077267     DOI : -
Core Subject : Engineering,
Jurnal Nasional Teknik Elektro (JNTE) adalah jurnal ilmiah peer-reviewed yang diterbitkan oleh Jurusan Teknik Elektro Universitas Andalas dengan versi cetak (p-ISSN:2302-2949) dan versi elektronik (e-ISSN:2407-7267). JNTE terbit dua kali dalam setahun untuk naskah hasil/bagian penelitian yang berkaitan dengan elektrik, elektronik, telekomunikasi dan informatika.
Arjuna Subject : -
Articles 610 Documents
Desain Kontrol Multi – Input DC–DC Converter Sistem Hibrid Turbin Angin dan Sel Surya Menggunakan Kontrol Fuzzy Logic untuk Tegangan Rendah Feby Agung Pamuji; Soe Dibyo
JURNAL NASIONAL TEKNIK ELEKTRO Vol 4 No 2: September 2015
Publisher : Jurusan Teknik Elektro Universitas Andalas

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (730.971 KB) | DOI: 10.25077/jnte.v4n2.165.2015

Abstract

this paper describes a hybrid system that consist of  Wind Turbines and Photovoltaic to supply electricity continuously for  load. Output of Wind Turbines and Photovoltaic is controlled in order to generate maximum power. Multiple-input dc-dc converters is used to control power flow in order to have MPP (Maximum Power Point). Converter control using Fuzzy logic controller to control the output in order to be obtained MPP (Maximum Power Point) from Wind Turbines and Photovoltaic, so the efficiency of wind turbines and photovoltaic can be improved.Keywords : Maximum Power Point, Hybrid System, Fuzzy logic controllerAbstrak—Dalam makalah ini diuraikan sistem hibrid yang menggabungkan Turbin Angin dan Photovoltaic untuk memasok listrik terus-menerus pada beban. Output dari Turbin Angin dan Photovoltaic diatur agar menghasilkan daya yang maksimum. Konverter multiple-input buck-boost dc-dc digunakan untuk mengatur aliran daya agar didapatkan MPP(Maximum Power Point). Kontrol konverter menggunakan Fuzzy Logic controller untuk mengkontrol output sehingga didapat MPP(Maximum Power Point) dari Turbin Angin dan Photovoltaic, sehingga effisiensi dari Turbin Angin dan Photovoltaic dapat ditingkatkan.Kata Kunci : Maximum Power Point, system hibrid, Fuzzy Logic controller 
Uji Performansi Kontrol Suhu dan Kelembaban Menggunakan Variasi Kontrol Digital dan Kontrol Scheduling untuk Pengawetan Buah dan Sayuran Rofan Aziz; Karsid .
JURNAL NASIONAL TEKNIK ELEKTRO Vol 4 No 2: September 2015
Publisher : Jurusan Teknik Elektro Universitas Andalas

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (540.408 KB) | DOI: 10.25077/jnte.v4n2.166.2015

Abstract

Currently the preservation of fruit and vegetables in Indonesia is still done with traditional. Most post-harvest handling of fruits and vegetables in Indonesia directly sold into the market. So at harvest, the quantity of the commodity is abundant and when the time of harvest finished exhausted and rare commodity. In the fruit and vegetable preservation, temperature and relative humidity are two control variables that influence each other. Where the increase and decrease in temperature will result in changes in relative humidity. In this research carried out two variations control the digital control and control scheduling to determine the characteristics of the relationship of temperature and relative humidity . Results from both trials showed that the variation of the control of digital control has a good quick peak time to reach the set point temperature and humidity. While scheduling control humidity rise with the increase in temperature.      Keywords : Temperature, Relative Humidity, Fruits, Vegetables, preservation. Abstrak—Saat ini proses pengawetan buah dan sayuran di Indonesia masih dilakukan dengan cara tradisional. Banyak buah dan sayuran pasca panen langsung dijual ke pasar. Sehingga pada saat panen, kuantitas komoditi tersebut melimpah dan disaat waktu panen selesai komoditi tersebut habis dan langka. Pada pengawetan buah dan sayuran, suhu dan kelembaban relatif merupakan dua variabel kontrol yang saling mempengaruhi. Dimana kenaikan dan penurunan suhu akan berakibat pada perubahan kelembaban relatif. Pada penelitian kali ini dilakukan dua variasi kontrol yaitu kontrol digital dan kontrol scheduling untuk mengetahui karakteristik hubungan suhu dan kelembaban relatif. Hasil dari uji kedua variasi kontrol tersebut didapatkan bahwa kontrol digital memiliki waktu puncak yang cepat baik untuk mencapai set point suhu dan kelembaban. Sedangkan kontrol scheduling kenaikan kelembaban mengikuti kenaikan suhu.    Kata Kunci : Suhu, Kelembaban Relatif, Buah, Sayuran, Pengawetan
Perancangan Modifikasi Antena Kupu – Kupu Panjang Dual Frekuensi untuk Aplikasi Hypherthermia Kiki Kananda; Hanalde Andre; Agus Rahmad Timor; Khairullah .; Erliwati .; Zulka Hendri
JURNAL NASIONAL TEKNIK ELEKTRO Vol 4 No 2: September 2015
Publisher : Jurusan Teknik Elektro Universitas Andalas

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (609.508 KB) | DOI: 10.25077/jnte.v4n2.168.2015

Abstract

Therapy device of Electromagnetic Wave radiation  hypherthermia used clinically to heat tissue in the human body. Increased temperatures are not followed by tissue outside the body. The use of electromagnetic waves at frequencies 915 and 2450 MHz has been proven and widely used in hypherthermia. The design modifications butterfly antenna done by simulation using finite element method. The simulation results show the modification of antenna can work in both frequency hypherthermia. Optimal shape of the antenna produce 'return loss' (RL) -16.6295 dB at a frequency of 915 MHz and -18.2697 dB at frequency 2450 MHz.        Keywords : Hyperthermia, Dual Frequency, Antenna Application Abstrak—Radiasi gelombang elektromagnetik pada alat terapi hypherthermia digunakan secara klinis untuk memanaskan jaringan dalam tubuh manusia. Peningkatan temperatur tidak diikuti oleh jaringan luar tubuh. Penggunaan gelombang elektromagnetik pada frekuensi 915 dan 2450 MHz telah terbukti dan banyak digunakan dalam hypherthermia. Perancangan modifikasi antenna kupu – kupu panjang dilakukan dengan simulasi menggunakan metoda elemen hingga. Hasil simulasi menunjukan modifikasi antenna dapat bekerja pada kedua frekuensi hypherthermia. Bentuk optimal antena menghasilkan nilai return loss (RL) -16.6295dB pada frekuensi 915 MHz dan -18.2697dB pada frekuensi 2450 MHzKata Kunci : Hyperthermia, frekuensi ganda, Aplikasi Antena,
Analisa Kekokohan Tanggapan Tegangan Sistem Eksitasi Generator Tipe Arus Searah Dengan Berbagai Pengendali Heru Dibyo Laksono; Doohan Haliman; Aidil Danas; Wayu Diafridho A
JURNAL NASIONAL TEKNIK ELEKTRO Vol 4 No 2: September 2015
Publisher : Jurusan Teknik Elektro Universitas Andalas

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (478.65 KB) | DOI: 10.25077/jnte.v4n2.169.2015

Abstract

The voltage response robustness of generator excitation system is the ability of generator excitation system to muffle noise at high frequency, has rapid response to specific input and is able to eliminate disturbance during operation. In this journal is conducted a discussion about the voltage response robustness analysis of generator excitation system with various controllers. By using the criteria of the maximum peak value, phase margin and gain margin are analyzed the voltage response robustness of generator excitation. The criteria of maximum peak value is divided into two specifically the criteria of the sensitivity maximum peak value and the criteria of the complementary sensitivity maximum peak value. The type of controllers are designed include Proportional controller (P), Proportional Integral controller (PI), Proportional Differential controller (PD), Proportional Integral Differential controller (PID), Proportional Differential controller with First Order Filter In Part Differential (PDF) and Proportional Integral Differential controller with First Order Filter in Part Differential (PIDF). The results showed that the voltage response of generator excitation system with Proportional controller (P), Proportional Integral controller (PI), Proportional Differential controller (PD), Proportional Integral Differential controller (PID) Proportional Differential controller with First Order Filter In Part Differential (PDF) and Proportional Integral Differential controller with First Order Filter in Part Differential (PIDF) is robust to disturbance, able to reduce noise at high frequencies and having rapid response to specific input. This is evidenced by sensitivity peak value smaller than 2.0000 and complementary sensitivity peak value smaller than 1.2500, the minimum limit of gain margin greater than 6.0000 dB and the minimum limit of phase margin between 30.0000 degrees to 60.0000 degrees for each controller.Keyword: robustness, excitation system, sensitivity maximum peak, complementary sensitivity maximum peak, gain margin, phase margin Abstrak— Kekokohan tanggapan tegangan sistem eksitasi generator merupakan kemampuan dari sistem eksitasi generator untuk meredam derau pada frekuensi tinggi, mempuyai tanggapan yang cepat terhadap masukan tertentu dan mampu menghilangkan gangguan pada saat beroperasi.  Pada jurnal ini dilakukan pembahasan tentang analisa kekokohan tanggapan tegangan sistem eksitasi generator dengan berbagai pengendali. Dengan menggunakan nilai kriteria puncak maksimum dan kriteria margin penguatan dan margin fasa dilakukan analisa kekokohan pada tanggapan tegangan sistem eksitasi generator. Kriteria nilai puncak maksimum ini terbagi atas 2 bahagian yaitu nilai kriteria puncak maksimum sensitivitas dan nilai kriteria puncak maksimum sensitivitas komplementer. Untuk jenis – jenis pengendali yang digunakan terdiri dari pengendali Proporsional (P), pengendali Proporsional Integral (PI), pengendali Proporsional Diferensial (PD), pengendali Proporsional Integral Diferensial (PID), pengendali Proporsional Diferensial dengan filter orde pertama pada bagian diferensial (PDF) dan pengendali Proporsional Integral Diferensial dengan filter orde pertama pada bagian diferensial (PIDF). Hasil yang diperoleh bahwa tanggapan tegangan sistem eksitasi generator dengan pengendali Proporsional (P),  pengendali Proporsional Integral (PI), pengendali  Proporsional Diferensial (PD), pengendali Proporsional Integral Diferensial (PID), pengendali Proporsional Diferensial dengan filter orde pertama pada bagian diferensial (PDF) dan pengendali Proporsional Integral Diferensial Dengan Filter Orde Pertama (PIDF) bersifat kokoh terhadap gangguan, mampu meredam derau pada frekuensi tinggi dan mempuyai tanggapan yang cepat terhadap masukan tertentu.  Hal ini dibuktikan dengan nilai puncak sensitivitas yang kecil dari 2.0000 dan nilai puncak sensitivitas komplementer yang kecil dari 1.2500, batasan minimum dari margin penguatan besar dari 6.0000 dB dan batasan minimum dari margin fasa antara 30.0000 derjat s/d 60.0000 derjat untuk setiap pengendali.Kata kunci :  kekokohan, sistem eksitasi, puncak maksimum sensitivitas, puncak maksimum sentivitas komplementer, margin penguatan, margin fasa.  
Kontrol Kecepatan Robot Hexapod Pemadam Api menggunakan Metoda Logika Fuzzy Darwison .; Rian Wahyudi
JURNAL NASIONAL TEKNIK ELEKTRO Vol 4 No 2: September 2015
Publisher : Jurusan Teknik Elektro Universitas Andalas

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (713.328 KB) | DOI: 10.25077/jnte.v4n2.170.2015

Abstract

This study aims to create a hexapod robot speed control fire extinguisher using fuzzy logic method . By applying the method of fuzzy logic will make the robot move smoother and comparable to the distance . The input of the fuzzy logic method is obtained from three ultrasonic sensors as detection distance to the wall / barrier . Hexapod robot using a servomotor with torgue large enough to perform the movement . Robot speed will be faster if the purpose of the movement of the robot is still far from the wall / barrier and vice versa . Microcontroller with fuzzy logic -based program of its use as a controller movement . The results showed that more refined movement based on the distance read by the sensor , where the sensor is experiencing an error distance measurement is influenced by the material wall / barrier . For the wall material / to obstacle of the board experienced a reading error of 0.18 % , amounting to 0.5 % of books and dolls of 1.58 %.Keywords: hexapod robot, fuzzy logic, and speed controlABSTRAK—Penelitian ini bertujuan membuat kontrol kecepatan robot hexapod  pemadam api menggunakan metoda logika fuzzy. Dengan menerapkan metoda logika fuzzy akan membuat pergerakan robot lebih halus dan sebanding dengan jaraknya. Input dari metoda Logika fuzzy didapatkan dari tiga sensor ultrasonik sebagai pendeteksi jarak terhadap dinding/penghalang. Robot hexapod menggunakan servomotor dengan torgue yang cukup besar untuk melakukan pergerakan. Kecepatan robot akan lebih cepat jika tujuan pergerakan robot masih jauh dari dinding/penghalang dan sebaliknya. Mikrokontroler dengan program berbasis fuzzy logic-nya digunakan sebagai pengontrol pergerakan. Hasil percobaan menunjukkan bahwa pergerakan lebih halus berdasarkan jarak yang terbaca oleh sensor, dimana sensor mengalami kesalahan pengukuran jarak yang dipengaruhi oleh bahan dinding/penghalang. Untuk bahan dinding/pengahalang dari papan mengalami kesalahan pembacaan sebesar 0,18%, buku sebesar 0,5% dan boneka sebesar 1,58%.Kata Kunci : robot hexapod, logika fuzzy, dan kontrol kecepatan
Solusi Aliran Daya Untuk Sistem Distribusi Tak Seimbang dengan Menggunakan Metode Trust-Region Rudy Gianto; Kho Hie Khwee
JURNAL NASIONAL TEKNIK ELEKTRO Vol 5 No 1: Maret 2016
Publisher : Jurusan Teknik Elektro Universitas Andalas

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (235.157 KB) | DOI: 10.25077/jnte.v5n1.171.2016

Abstract

In this research, the trust-region method has been proposed for solving the power flow problem of an unbalanced distribution system. The proposed method has been successfully applied in solving the power flow problems of three unbalanced distribution networks, i.e. 10-bus, 19-bus and 25-bus systems. The results of investigation obtained by the proposed method were compared to the previously reported results and were found to be in exact agreement                                                    Keywords : power flow, distribution system, trust-region methodAbstrak—Pada penelitian ini, telah dibahas penggunaan dari metode trust-region untuk menyelesaikan masalah aliran daya pada sistem distribusi tak-seimbang. Metode yang diusulkan tersebut telah berhasil diaplikasikan pada pada tiga buah sistem distribusi tak-seimbang yaitu: sistem 10-bus, 19-bus dan 25-bus. Hasil-hasil penelitian memperlihatkan bahwa nilai-nilai yang diperoleh melalui metode trust-region adalah sangat sesuai dengan nilai-nilai yang didapat melalui metode lain yang sebelumnya telah dipublikasikanKata Kunci : aliran daya, sistem distribusi, metode trust-region
Klasifikasi Penyakit Paru Berdasarkan Citra Rontgen dengan Metoda Segmentasi Sobel Reni Rahmadewi; Rahmadi Kurnia
JURNAL NASIONAL TEKNIK ELEKTRO Vol 5 No 1: Maret 2016
Publisher : Jurusan Teknik Elektro Universitas Andalas

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (325.741 KB) | DOI: 10.25077/jnte.v5n1.174.2016

Abstract

Lung disease is one of the diseases that are prevalent in society. Often there is a delay in the treatment of this lung disease. These delays are often caused by ignorance of the community in the proper handling and lack of clear information about lung disease. One way to detect lung disease is by reading the X-ray images are correct and are usually carried out by experts who are experts on the X-ray results. But to get the diagnosis depends on the schedule of expert practice and takes a long time. To ease the difficulties of this society, so in this study built applications that can analyze X-ray images based on image processing. The data is processed there are 41 (forty-one) X-ray image of the segmentation of the lung region. Then the lung region performed  edge detection based  on Sobel operator . The test results obtained from the comparison of pixels  between the results of edge detection on the lung region, which classifies six (6) types of lung disease with a percentage interval for bronchitis of 1.43% - 1.59%, pleurisy 1.43% - 1.59 %, pneumonia 2.00% - 2.50%, tuberculosis 2.86% - 3.79%, emphysema 4.16% - 4.76% and lung cancer 76.72% - 94.85%.Keyword : lung disease, X-ray image, segmentation, Sobel OperatorAbstrak—Penyakit paru merupakan salah satu penyakit yang umum dijumpai di masyarakat. Seringkali terjadi keterlambatan dalam penanganan terhadap penyakit paru ini. Keterlambatan ini biasanya disebabkan oleh ketidaktahuan masyarakat dalam penanganan yang tepat dan kurangnya informasi yang jelas tentang penyakit paru. Salah satu cara untuk mendeteksi penyakit paru adalah dengan membaca gambar rontgen yang benar dan biasanya dilakukan oleh pakar yang ahli terhadap hasil rontgen tersebut. Akan tetapi untuk mendapatkan hasil diagnosa ini tergantung pada jadwal praktek dari pakar dan membutuhkan waktu yang lama. Untuk memudahkan kesulitan masyarakat ini, maka pada penelitian ini dibangun aplikasi yang bisa menganalisa gambar rontgen berdasarkan pengolahan citra. Data yang diolah ada 41 (empat puluh satu) citra rontgen dengan melakukan segmentasi terhadap region paru. Kemudian region paru ini dilakukan deteksi tepi berbasis operator sobel. Hasil pengujian didapatkan dari perbandingan piksel antara hasil deteksi tepi terhadap region paru, yang mengklasifikasikan 6 (enam) jenis penyakit paru dengan interval persentase untuk penyakit bronkitis sebesar 1,43% - 1,59%, penyakit pleuritis 1,43% - 1,59%, penyakit pneumonia 2,00% - 2,50%, penyakit TBC 2,86% - 3,79%, penyakit emfisema 4,16% - 4,76% dan penyakit kanker paru 76,72% - 94,85%.Kata Kunci : Penyakit paru, citra rontgen, segmentasi, operator sobel.
Penguat Audio Kelas D Dengan Umpan Balik Tipe Butterworth Gunawan Dewantoro; Franciscus Dalu Setiaji; Tio Pragustha
JURNAL NASIONAL TEKNIK ELEKTRO Vol 5 No 1: Maret 2016
Publisher : Jurusan Teknik Elektro Universitas Andalas

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (506.977 KB) | DOI: 10.25077/jnte.v5n1.178.2016

Abstract

A class D amplifier would, in ideal sense, amplify signals without any noises and distortions which yield 100% efficiency and 0% Total Harmonic Distortion (THD). However, class D amplifiers have some drawbacks that lead to nonlinearity and increasing THD. Therefore, a feedback mechanism was employed to enhance THD performance of amplifier. Some feedback techniques have been using first order filter in the feedback path to retrieve audio signals. This research proposed a second order filter with Butterworth approach. A power amplifier was realized using full-bridge amplifier with MOSFETs to provide greater power. This class D amplifier was designed to meet following specifications: maximum output power up to 32.6 W with an 8 Ω load, sensitivity of 90 mV/W, frequency response ranging from 20 Hz – 20 kHz with tolerance ± 1 dB, THD as low as 1.1 %, SNR up to 90.16 dB, and efficiency of 82.1%.    Keywords : Class D Amplifier, Feedback, Butterworth, Total Harmonic Distortion                                                                                    Abstrak—Proses penguatan sinyal pada penguat kelas D idealnya tidak terdapat derau dan distorsi sehingga penguat kelas D dapat menghasilkan efisiensi hingga 100 % dan THD (Total Harmonic Distortion) 0%. Namun pada praktisnya, penguat kelas D memiliki beberapa kekurangan yang menyebabkan keluaran penguat kelas D menjadi tidak linear sehingga mengakibatkan naiknya THD. Oleh karena permasalahan tersebut, diberikan sutau mekanisme umpan balik negatif yang dapat memperbaiki kualitas THD dari penguat. Beberapa teknik umpan balik negatif menggunakan tapis orde 1 pada umpan balik untuk mendapatkan frekuensi audio. Penelitian ini merancang teknik umpan balik negatif menggunakan tapis orde 2 dengan pendekatan Butterworth. Penguat daya diwujudkan menggunakan penguat jembatan penuh dengan MOSFET yang dapat menghasilkan daya lebih besar. Penguat kelas D yang dibuat mempunyai spesifikasi antara lain: daya keluaran maksimum mencapai 32,6 Watt pada beban 8 Ω, dengan kepekaan penguat 90 mV/W, memiliki tanggapan frekuensi 20 Hz – 20 kHz dengan toleransi ± 1 dB, THD dengan umpan balik mencapai 1,1 % , SNR hingga 90,16 dB serta efisiensi penguat mencapai 82,1%.                                                       Kata Kunci : Penguat Kelas D, Umpan Balik, Butterworth, Total Harmonic Distortion
Pemantauan Ruang Inkubator Penetasan Telur Ayam Dengan Berbasis Telemetri Menggunakan Arduino Uno R3 Sofyan Shafiudin; Fida Jazilatur Rohma; Abdilla Eka Prasetya; Rifqi Firmansyah
JURNAL NASIONAL TEKNIK ELEKTRO Vol 5 No 1: Maret 2016
Publisher : Jurusan Teknik Elektro Universitas Andalas

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (809.418 KB) | DOI: 10.25077/jnte.v5n1.181.2016

Abstract

The need for data on environmental conditions around has been encouraging people to create a tool that can measure environmental conditions. One thing that could explain the environmental condition is temperature. In this study, designed a device that can measure the temperature in the incubator hatching chicken eggs and transmit data such as temperature telemetry. These devices can transmit data remotely and at any time the data is needed, making it easier for someone to monitor chicken egg incubator without always keeping. This research was done by designing, manufacturing, and testing telemetry system which consists of two main parts namely the transmitter and receiver. In the transmitter section consists of components temperature sensors, Arduino Uno R3 and RF Module Board 433 MHz, while the receiver section consists of an Arduino Uno R3, laptops, and RF 433 MHz Module Board. The main function of Arduino Uno R3 is as processing data from temperature sensors and sends the data to the receiver. Based on research results when transmitter and receiver are placed in ambient conditions without barriers (there are gaps), the system can run properly and there is no error in the distance range up to 8 meters. Meanwhile, when the transmitter and receiver placed entirely unobstructed walls, obtained by the system can not run well, although the distance is close to 1 meter.Keywords : Telemetry , Temperature Sensor , Arduino Uno R3, Transmitter & Receiver Abstrak-Kebutuhan akan data mengenai kondisi lingkungan sekitar telah mendorong manusia untuk membuat alat yang bisa mengukur kondisi lingkungan. Salah satu hal yang bisa menjelaskan mengenai kondisi lingkungan adalah suhu. Pada penelitian ini, dirancang suatu perangkat yang dapat mengukur suhu pada inkubator penetasan telor ayam dan mengirimkan data yang berupa suhu secara telemetri. Perangkat ini dapat mengirimkan data dari jarak jauh dan pada waktu kapanpun data tersebut dibutuhkan, sehingga memudahkan seseorang dalam memantau inkubator telor ayam tanpa harus selalu menjaganya. Penelitian ini dilakukan dengan cara merancang, membuat, dan melakukan uji coba sistem telemetri yang terdiri dua bagian utama yakni transmitter dan receiver. Pada bagian transmitter terdiri komponen sensor suhu, Arduino Uno R3, dan RF Module Board 433 MHz, sedangkan bagian receiver terdiri atas Arduino Uno R3,  laptop, dan RF Module Board 433 MHz. Fungsi utama Arduino Uno R3 adalah sebagai pemroses data dari sensor suhu dan mengirimkan data kepada receiver. Berdasarkan hasil penelitian ketika transmitter dan receiver diletakkan dalam kondisi ruangan tanpa penghalang ( terdapat celah ), sistem dapat berjalan dengan baik dan tidak terjadi kesalahan dalam jangkauan jarak maksimal 8 meter. Sedangkan, ketika transmitter dan receiver diletakkan dengan terhalang dinding sepenuhnya, diperoleh sistem tidak dapat berjalan dengan baik, walaupun jaraknya dekat 1 meter.Kata kunci : Telemetri , Sensor Suhu , Arduino Uno R3, Transmitter & Receiver
Desain Sistem Kontrol Penyalaan Lampu dan Perangkat Elektronik untuk Meniru Keberadaan Penghuni Rumah Zulfikar .; Zulhelmi .; Khairul Amri
JURNAL NASIONAL TEKNIK ELEKTRO Vol 5 No 1: Maret 2016
Publisher : Jurusan Teknik Elektro Universitas Andalas

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (366.877 KB) | DOI: 10.25077/jnte.v5n1.182.2016

Abstract

This paper proposes a system for controlling bulbs and electrical appliances in order to imitate the availability of owner in a house. The designed system is able to switch ON and OFF the equipments randomly for treating the availability the owners in their houses. The system generates a number randomly every 15 minutes. Each number associated with bulb or electrical device in the controlling list. The electrical devices will be ON or OFF based on specific duration times. The system is realized using an Arduino board, an RTC, power supply unit, and interface circuit of Arduino and electrical devices. The designed system has been tested for 5 consecutive days normalized to 2 hour normal time on the control device and house miniature. The miniature is used to mimic condition the real house. Electric consumption estimated about 0.42 kWh per dayKeywords : Arduino, Random Numbers, Electrical Appliances, Control Systems, Housing SecurityAbstrak—Pada penelitian ini dirancang sebuah sistem kontrol penyalaan lampu dan perangkat elektronik untuk meniru keberadaan penghuni rumah. Sistem dirancang untuk mengontrol penyalaan beberapa lampu dan perangkat elektronik secara acak. Hal tersebut bertujuan untuk menimbulkan kesan bahwa rumah yang ditinggalkan seakan-akan ada penhuninya. Sistem keamanan ini bekerja dengan cara membangkitkan sebuah bilangan acak setiap 15 menit. Setiap bilangan acak yang dibangkitkan mengacu kepada peralatan listrik yang dikontrol. Peralatan listrik rumah yang telah nyala akan padam ketika lamanya waktu yang ditetapkan tercapai. Sistem ini dirancang terdiri dari Arduino, catu daya, RTC dan interface perantara dengan perlatan listrik. Sistem telah diuji selama 5 hari waktu normalisasi terhadap sistem kontrolnya dan sistem miniatur rumah. Miniatur rumah dibuat untuk mewakili kondisi rumah yang sebenarnya. Konsumsi daya listrik perhari dari sistem yang dibuat adalah 0,42 kWh.Kata Kunci : Arduino, Bilangan Acak,  Peralatan Listrik, Sistem Kontrol, Keamanan Rumah