cover
Contact Name
Muhammad Afief Ma'ruf
Contact Email
afief84@gmail.com
Phone
+6281803821373
Journal Mail Official
infoteknik.ftunlam@gmail.com
Editorial Address
Fakultas Teknik Universitas Lambung Mangkurat, Jl. Ahmad Yani Km. 35 Banjarbaru Kalimantan Selatan Telp. (0511)-4773868 Fax. (0511)-4773868
Location
Kota banjarmasin,
Kalimantan selatan
INDONESIA
Info-Teknik
ISSN : 08532508     EISSN : 24599964     DOI : http://dx.doi.org/10.20527
Core Subject : Engineering,
Jurnal Info – Teknik menerbitkan artikel – artikel karya orisinil dan signifikan pada Bidang Rekayasa Teknik.
Articles 420 Documents
PENGARUH PENGELASAN GTAW PADA LOGAM BIMETAL PLAT BAJA KARBON RENDAH DAN STAINLESS STEEL TERHADAP SIFAT MEKANIK SAMBUNGAN LAS Lisa Agustriyana; Sarjiyana Sarjiyana; Suyanta Suyanta
INFO-TEKNIK Vol 20, No 2 (2019): INFOTEKNIK VOL. 20 NO. 1 DESEMBER 2019
Publisher : Universitas Lambung Mangkurat

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.20527/infotek.v20i2.7712

Abstract

Stainless steel material (stainless steel) is used in the home industry and the military industry, and also in the nuclear industry. Steel material is divided into five types, namely austenite, ferrite, martensite, duplex and precipitation hardening. Ferritic stainless steel is an attractive alternative in vehicle production because of its corrosion resistance. Different metals have different characteristics from one another, so the welding process of dissimilar metals requires certain techniques. The purpose of this study is to determine the tensile strength of welds in bimetallic welding between low carbon steel plates and stainless-steel plates and to know the hardness of welds in bimetal welding between low carbon steel plates and stainless-steel plates using GTAW welding. The research method used: this research is part of the testing of technical materials conducted by the destructive test method with the category of science and technology development in the field of Mechanical Engineering. There is a trend of increasing tensile strength, yield strength and hardness of bimetallic welding of low carbon steel plates and stainless-steel plates using GTAW welding, that the greater the welding amperes will increase tensile strength, yield strength and hardness. The highest tensile strength was 41.18 Kg / mm2 and the highest yield strength was 41.16 Kgf / mm2 at 60 amperes and the highest hardness was 571.01 BHN at 55 amperes with the corresponding amperage range from the usage table 45 - 65 amperes. In the HAZ area when compared to the parent material, the HAZ area hardness is higher than the parent material and lower than the weld filler.
SINTESIS BIODIESEL DARI CRUDE PALM OIL DENGAN KATALIS ALUMINA HASIL RECOVERY LIMBAH PADAT LUMPUR PDAM INTAN BANJAR Doni Rahmat Wicakso
INFO-TEKNIK Vol 12, No 1 (2011): INFOTEKNIK VOL. 12 NO. 1 2011
Publisher : Universitas Lambung Mangkurat

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.20527/infotek.v12i1.1774

Abstract

The purposed of this research is to prove the ability of alumina which is obtained from PDAM sludge waste as a catalyst in biodiesel syntetic from crude palm oil and to get the optimum additions of alumina catalyst and the optimum temperature of process. Alumina catalyst is a heterogeneous catalyst or a catalyst which is consisting in solid phase. The advantage of this alumina catalyst is its ability to recovered, reusable, and simple in its separation process, because the soluble product in reaction medium could be separated from its catalyst by filtration. Alumina was obtained from PDAM sludge waste by adding NaOH, NH4Cl, and NH4OH in it, then heat at 90oC for 2,5 hours,  filtrated, and dried in the oven. Esterification process works by heating methanol, H2SO4, and CPO at 60oC by comparison of CPO and methanol 1:6 in moles. Continued with transesterification process by temperature variations of 40oC, 50oC, 60oC, and 70oC, also alumina catalyst variations of 3%-b, 4%-b, and 5%-b. After esterification-transesterifications process, we purified crude biodiesel by wash it with aqudest to make pure crude biodiesel.Optimum temperature in this research about 60oC with optimum catalyst about 5%. It was  reasoned by optimum yield we obtained about 70,5%. 
Efektivitas Pengaturan Lampu Lalu Lintas Pada Persimpangan Di Banjarmasin Rosehan Anwar
INFO-TEKNIK Vol 4, No 1 (2003): INFOTEKNIK VOL. 4 NO. 1 2003
Publisher : Universitas Lambung Mangkurat

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.20527/infotek.v4i1.470

Abstract

Pada tengah malam hari rasanya tidak aman sendiri pada persimpangan Traffic Light, Apalagi pada Persimpangan Pangeran Samudra-Lambung Mangkurat ternyata pada malam hari Traffic Light tetap berfungsi seperti pada siang hari. Atau dengan kata lain pengaturan lampu lalu lintas pada volume lalu lintas yang kecil pada malam hari dan volume lalu lintas besar pada siang hari seting lampunya sama.Tujuan penelitian adalah untuk setting lampu lalu lintas secara effektif pada malam hari. Pengaturan lampu lalu lintas menggunakan metode IHCM.92 (MKJI). Hasil yang didapatkan dari jam 22:45 sampai jam 05:30 berdasarkan volume lalu lintas didapatkan nilai Cycle time © = < 40 detik. Sehingga disimpulkan mulai jam 22:45  sampai jam 05:30 Lampu lalu lintas hanya kedip kedip kuning. 
PENGARUH PUTARAN TURBIN ANGIN SUMBU HORIZONTAL KOMBINASI PEMBERAT BOLA PEJAL Firda Herlina; Mujiburrahman Mujiburrahman; Adi Asyari
INFO-TEKNIK Vol 21, No 1 (2020): INFOTEKNIK VOL. 21 NO. 1 JULI 2020
Publisher : Universitas Lambung Mangkurat

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.20527/infotek.v21i1.8968

Abstract

Along with the increase in population is directly proportional to the need for energy sources both to support people's lives and the increase in the industrial sector in Indonesia. One of the most widely used sources of electricity is wind. Wind turbines are very sensitive to the wind speed they receive, as a result of fluctuations in wind speed that affect wind rotation speed. For this reason, the author has the idea to combine a wind turbine with a solid object turbine, it is hoped that the combination can produce more consistent rotation. The tool used is a wind turbine combined with solid blade ball weights 8, 9 and 10 and ballast of 10 gr, 20 gr and 30 gr for each blade and wind speeds of 3.3 m / s, 3.6 m / s and 3.9. m / s with the experimental research method, the experiment was carried out 3 times in each tool for ± 2 minutes which was expected to produce a combination of the variables studied in the form of a turbine with the maximum rotational speed and the most consistent rotation. From these experiments, it was found that a turbine with 10 blades, a weight of 10 gr at a wind speed of 3.9 m / s had the fastest rotation, namely 116.43 rpm while a 9 blade turbine with a weight of 30 gr at all three wind speeds was the turbine with the most consistent rotation, namely the difference between the top and bottom rotation is 2.53 rpm.
T-PIKON-H SEBAGAI TEKNOLOGI ALTERNATIF UNTUK PERBAIKAN SANITASI DI DAERAH SPESIFIK RAWA Rijali Noor
INFO-TEKNIK Vol 12, No 2 (2011): INFOTEKNIK VOL. 12 NO. 2 2011
Publisher : Universitas Lambung Mangkurat

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.20527/infotek.v12i2.1808

Abstract

Daerah spesifik adalah daerah dimana kondisi geografis/iklim sedemikian rupa sehingga sistem pelayanan sanitasi baik konvensional/non konvensional sulit untuk diterapkan. T-Pikon-H sebagai septic-tank individual dipilih sebagai opsi sanitasi yang cocok diterapkan di daerah spesifik rawa air tawar.Tujuan penelitian: (1) Mengetahui kondisi air, sanitasi, dan kesehatan penduduk Desa Penggalaman; (2) Mengetahui kualitas air rawa tawar di Desa Penggalaman; (3) Bagaimana penerapan T-Pikon-H secara fungsional sebagai septic-tank individual; (4) Mengetahui keefektifan penggunaan kakus T-Pikon-H sebagai septic-tank yang diterapkan di daerah spesifik rawa air tawar Desa Penggalaman di tinjau dari parameter pH, BOD, COD dan colitinja. Penelitian ini bersifat eksperimen skala laboratorium kapasitas 27 liter yang uji cobanya diterapkan di salah satu rumah penduduk di daerah perairan rawa Desa Penggalaman Kecamatan Martapura Barat Kab.Banjar. Pengambilan sampel influent dan effluent dilakukan setelah melewati waktu tinggal 3 hari pada alat hingga 4-5 kali perulangan. Selain itu, penelitian ini didukung dengan data kuesioner untuk mengetahui kondisi air, sanitasi dan kesehatan penduduk Desa Penggalaman pada RT 01,02 dan 03 serta diperkuat adanya uji kualitas air rawa dengan parameter pH, BOD,COD dan colitinja. Hasil penelitian menunjukkan, Desa Penggalaman untuk kondisi air penduduk memperoleh air bersih dari irigasi, pedagang, sungai dan air hujan berturut-turut: 51%, 27%, 9%, 13%. Untuk kondisi sanitasi, jenis kakus yang digunakan 16% kloset siram/leher angsa dan 84% jamban cemplung. Kondisi kesehatan, hampir 73% responden menjawab tidak ada penyakit yang menyerang penduduk Desa, hanya 18% menjawab penyakit kulit, 7% demam biasa, dan 2% diare. Uji kualitas air rawa Desa Penggalaman, dengan pengambilan sampel hulu, tengah, hilir. Nilai pH berturut-turut adalah 5. Nilai BOD berturut-turut 1,44 mg/l; 0,8 mg/l; 0,8 mg/l. Nilai COD berturut-turut 62,18 mg/l; 69,18 mg/l; 64,48 mg/l. Nilai colitinja yang di ukur hanya bagian tengah bernilai 33.000 MPN/100ml. Sesuai PerGub Kal-Sel No.5 Tahun 2007, untuk pH, COD dan colitinja kondisi perairan mengalami penurunan kualitas air. Secara fungsional, dari segi pemasangan, alat T-Pikon-H dapat dipasang di daerah rawa dengan memperhatikan kondisi ketinggian muka air rawa. Dari segi pemakaiannya, tidak ditemukan keluhan berupa bau-bau yang masuk ke dalam rumah.Uji keefektifan T-Pikon-H, diperoleh data untuk pH dari 5 kali pengambilan sampel berturutturut terjadi kenaikan pH yang nilainya 6, 6, 7, 8, 8. Pada data BOD, pengambilan sampel ke-1 influent 5,12 mg/l effluent 11,8 mg/l; sampel ke-2 influent 7,2 mg/l effluent 12,8 mg/l; sampel ke-3 influent 13,6 mg/l effluent 2,56 mg/l; sampel ke-4 influent 3,84 mg/l effluent 1,6 mg/l dan sampel ke-5 influent 2,4 mg/l effluent 4,4 mg/l. Pada data COD, pengambilan sampel ke-1 influent 73,69 mg/l effluent 69,08 mg/l; pengambilan sampel ke-2 influent 76,76 mg/l effluent 82,9 mg/l; pengambilan sampel ke-3 influent 84,44 mg/l effluent 46,06 mg/l; pengambilan sampel ke-4 influent 79,83 mg/l effluent 92,11 mg/l dan pengambilan sampel ke-5 influent 95,95 mg/l effluent 76,76 mg/l. Pada data colitinja, dari 4 kali pengambilan sampel hanya pada pengambilan sampel pertama yang mengalami penurunan jumlah colitinja sampel ke-1 influent > 1.600.000 MPN/100ml effluent 210.000 MPN/100ml. 3 sampel lainnya tidak mengalami penurunan jumlah colitinja. Sehingga keefektifan alat ditinjau dari parameter pH, BOD, COD dan colitinja alat T-Pikon-H belum cukup efektif dalam penurunan parameter tersebut.
Pengaruh Kedalaman Tancap, Spasi, dan Jumlah Cerucuk dalam Peningkatan Tahanan Geser Tanah Lunak Berdasarkan Permodelan di Laboratorium Rusdiansyah Rusdiansyah; Indrasurya B. Mochtar; Noor Endah Mochtar
INFO-TEKNIK 2015: Prosiding Semnas Teknik Sipil 2015
Publisher : Universitas Lambung Mangkurat

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.20527/infotek.v0i0.3038

Abstract

Belakangan ini pemakaian cerucuk cukup efektif sebagai metode alternatif perkuatan stabilitas lereng maupun perkuatan embankment jalan. Pada embankment jalan, cerucuk  digunakan sebagai bahan yang kaku berfungsi untuk menaikkan stabilitas tanah. Sebagai perkuatan lereng, cerucuk sangat efektif berfungsi sebagai pasak/tulangan yang dapat memotong bidang kelongsoran lereng. Sehingga cerucuk dapat memberikan tambahan gaya geser pada lereng yang mampu melawan gaya geser longsoran yang terjadi. Tambahan gaya geser yang dihasilkan oleh cerucuk tersebut dapat meningkatkan angka keamanan (safety factor) stabilitas lereng.Akhir-akhir ini pengembangan teori tentang konstruksi perkuatancerucuk padastabilitas lereng tanah lunak guna menambah kekuatan gesernya(yang mendekati kondisi di lapangan) masih sedikit dan belum memadai.Hanya saja untuk pengembangannya tersebut sangat diperlukan informasi yang rinci dan jelas tentang interaksi antara tanah lunak dengancerucuk. Informasi tersebut dapat diperoleh salah satunya dari penelitian skala laboratorium yang dibuat mendekati kondisi lapangan.                Tujuan penelitian ini untuk menjawab bagaimana pengaruh panjang tancapan (rasio tancap) dan pengaruh jarak (spasi) antar cerucuk terhadap penambahan tahanan geser dari stabilitas lereng tanah lunak. Penelitian ini dilaksanakan melalui salah satu cara pendekatan model skala laboratorium, namun perilakunya dibuat mendekati perilaku sebenarnya di lapangan. Bidang kelongsoran lereng yang terjadi di lapangan didekati dengan bidang geser yang sengaja dibuat di laboratorium dengan menggeser contoh tanah (Plab) yang terdapat dalam kotak geser hasil modifikasi yang berukuran relatif besar pada alat geser langsung. Cerucuk yang akan digunakan berupa cerucuk kayu mini dan ditanamkan pada contoh tanah tadi.Variasi rasio tancap (L/D) yang diterapkan sebesar 5, 10, 15, dan 20.Sedangkaan variasi spasi cerucuk yang digunakan sebesar 3D, 5D, dan 8D.Sedangkan untuk variasi jumlah cerucuk yang dipasang yaitu 1 batang, 2 batang, 4 batang, dan 6 batang.Diharapkan dari perilaku skala kecil tersebut dihasilkan tambahan teori mengenai perkuatan lereng dengan cerucuk yang mendekati kondisi sebenarnya di lapangan.Hasil penelitian pendahuluan menunjukkan bahwa semakin besar rasio tancap yang digunakan cerucuk maka semakin meningkatkan tahanan geser tanah lunak.Selain itu tahanan geser tanah lunak juga meningkat apabila spasi antar cerucuk yang digunakan sebesar 3D sampai 5D.Akan tetapi penurunan tahanan geser tanah lunak terjadi apabila spasi antar cerucuk yang digunakan adalah lebih besar dari 5D.Selain itu bahwa tahanan geser tanah menjadi meningkat seiring dengan adanya penambahan jumlah cerucuk. Kelompok cerucuk yang menerima gaya geser horisontal pada arah sejajar terhadap baris kelompoknya (PolaPemasangan  1) menghasilkan tahanan geser tanah yang relatif lebih besar daripada arah tegak lurus terhadap baris kelompoknya (Pola Pemasangan 2). Selain itu bahwa kemampuan kelompok cerucuk dalam menahan geseran horisontal juga dipengaruhi oleh faktor efisiensi. Dimana kemampuan kelompok cerucuk dalam menahan geseran horisontal tidak akan sama dengan kemampuan masing-masing cerucuk dikalikan dengan jumlah cerucuk dalam kelompok yang bersangkutan.
ANALISA ANTRIAN DI TERMINAL KEBERANGKATAN BANDARA SYAMSUDIN NOOR BANJARMASIN Muhammad Arsyad; Yaula Stellamaris
INFO-TEKNIK Vol 13, No 2 (2012): INFOTEKNIK VOL. 13 NO. 2 2012
Publisher : Universitas Lambung Mangkurat

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.20527/infotek.v13i2.1833

Abstract

Peningkatan jumlah penumpang pesawat yang terus menerus  mengakibatkan terjadinya kepadatan di bandara. Salah satu dampak kepadatan di bandara adalah terpengaruhnya tingkat pelayanan di terminal keberangkatan. Tujuan yang ingin dicapai dalam penelitian ini adalah mengetahui berapa jumlah loket pelayanan X-Ray dan Check-in di Terminal Keberangkatan minimal harus dibuka dan bagaimana kinerja proses antrian yang terjadi, dan berapa jumlah loket pelayanan minimal harus dibuka agar memenuhi standar Level of Service . Agar memenuhi standar Level of Service, jumlah counter pelayanan X-Ray  yaitu minimal 2 buah counter.
ANALISA PENGARUH KESIAPAN SUPPLY BATUBARA TERHADAP DEMURRAGE VESSEL, DI PT. INDOMINCO MANDIRI, BONTANG, KALIMANTAN TIMUR Sakdillah Sakdillah
INFO-TEKNIK Vol 17, No 1 (2016): INFOTEKNIK Vol. 17 No. 1 2016
Publisher : Universitas Lambung Mangkurat

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.20527/infotek.v17i1.1266

Abstract

Demurrage is a form of compensation due to violation of the time of loading and unloading cargo and usually stated in the lease contract of cooperation. Demurrage can sometimes cause a loss in the seller because it will increase the total cost of transportation. In 2010 PT. Indominco Mandiri received a loss by the lack of supply of coal to reach the 11 million USD. The variable is used as an object of research is the supply of coal and the actual rate of replenishment ships, supply of coal which is ready to sell the supply of coal production has an influence on the actual rate of replenishment ships. Analysis conducted to find the relationship and influence in this study using the Pearson product moment correlation analysis. The data used is the average of the actual supply of coal and ship loading rate in a year. The steps in the research is to determine the hypothesis in sentence form and statistics and make a helper table. Once complete data correlation calculation, obtained r = 0.674 and the relatively strong, diterminan coefficient of 45.37%, in order to know the influence of the coal supply to the actual charging rate is significant.
ANALISIS INTERVAL PERAWATAN KOMPONEN KRITIS UNIT MESIN STITCHING UNTUK MEMINIMUMKAN BIAYA PERAWATAN DAN MENINGKATKAN PRODUKTIVITAS Fina Andika Frida Astuti; Sugiono Sugiono; Moch. Agus Choiron
INFO-TEKNIK Vol 17, No 2 (2016): INFOTEKNIK VOL. 17 NO. 2 2016
Publisher : Universitas Lambung Mangkurat

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.20527/infotek.v17i2.2500

Abstract

PT. XYZ is a company producing Exercise Book. To date the company has not been able to meet the high market demand. Historical data shows unit 2015 Stitching machine that serves to menstaples book into one unit has a frequency of engine damage as much as 42 times. The amount of damage to the unit frequency Stitching machines because companies do not yet have a scheduled maintenance activity for each component so that the machine crashes arrived - arrived when operating. To overcome these problems required maintenance interval planning for critical components of the engine unit Stitching. From the analysis of the critical components discovered two critical components of the most influential, namely components Stitching Head and Stang. From the calculation Time to Failure (TTF) and Time to Repair (TTR) of critical components used for distribution menentuan damage and parameter values to calculate the value of MTTF and MTTR. Interval treatment for critical components Stitching Head is 23 days, while for critical components Stang is 72 days. The calculation of the cost of care of two critical components can save costs amounting to $ 1.310,08 from the previous year and an increase of productivity of 6,77 tonnes
Studi Pengaruh Penambahan Karbon Aktif Pada Optimasi Penurunan Warna Dan Kandungan Organik Pada Air Gambut Menggunakan Membran Ultrafiltasi Rony Riduan
INFO-TEKNIK Vol 6, No 1 (2005): INFOTEKNIK VOL. 6 NO. 1 2005
Publisher : Universitas Lambung Mangkurat

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.20527/infotek.v6i1.1673

Abstract

High organic content in peat water lower its quality as one of the surface water source.  Ultra filtration membrane system is applicable to this problem with support from PAC (Powdered Activated Carbon) pre-treatment in order to enhance its organic removal performance.Effect of   activated carbon pre-treatment to the performance of ultra filtration membrane system is analyzed from the optimum removal efficiency comparison. Optimation process is carried by analyzing the carbon active dose, contact time, acidity, applied pressure, and operating period effects in dead-end flow system.  Statistical approach is used to support the optimation method with RSM (Response Surface Model) and regression analysis.Activated carbon pre-treatment enhanced the colour rejection by 9.37% and organic rejection by 2.3% compared to non-pre-treated.  Flux difference from those methods is about 9.37% higher in the beginning of filtration process, and about 78% higher after 4 hours of operation.  Carbon active pre-treatment effects flux significantly but not as great in colour and organic rejection.  Optimum condition in organic removal from this system is measured at 3 bar applied pressure and ambient pH form carbon active pre-treatment.  Total colour and organic rejection is 98.02% and 98.54%. The highest flux obtained from this method is 24.47 L/m2.hour.  Generally, product from ultra filtration membrane system with activated carbon pre-treatment can achieve the drinking water quality standard.

Page 6 of 42 | Total Record : 420


Filter by Year

2000 2024


Filter By Issues
All Issue Vol 25, No 2 (2024): INFOTEKNIK VOL. 25 NO. 2 DESEMBER 2024 Vol 25, No 1 (2024): INFOTEKNIK VOL. 25 NO. 1 JULI 2024 Vol 24, No 2 (2023): INFOTEKNIK VOL. 24 NO. 2 DESEMBER 2023 Vol 24, No 1 (2023): INFOTEKNIK VOL. 24 NO. 1 JULI 2023 2023: PROSIDING SEMNAS TAHUNAN X 2023 Vol 23, No 2 (2022): INFOTEKNIK VOL. 23 NO. 2 DESEMBER 2022 Vol 23, No 1 (2022): INFOTEKNIK VOL. 23 NO. 1 JULI 2022 Vol 22, No 2 (2021): INFOTEKNIK VOL. 22 NO. 2 DESEMBER 2021 Vol 22, No 1 (2021): INFOTEKNIK VOL. 22 NO. 1 JULI 2021 Vol 21, No 2 (2020): INFOTEKNIK VOL. 21 NO. 2 DESEMBER 2020 Vol 21, No 1 (2020): INFOTEKNIK VOL. 21 NO. 1 JULI 2020 Vol 20, No 2 (2019): INFOTEKNIK VOL. 20 NO. 1 DESEMBER 2019 Vol 20, No 1 (2019): INFOTEKNIK VOL. 20 NO. 1 JULI 2019 Vol 19, No 2 (2018): INFOTEKNIK VOL. 19 NO. 2 DESEMBER 2018 Vol 19, No 1 (2018): INFOTEKNIK Vol. 19 No. 1 Juli 2018 Vol 18, No 2 (2017): INFOTEKNIK VOL. 18 NO.2 2017 Vol 18, No 1 (2017): INFOTEKNIK Vol. 18 No. 1 2017 Vol 17, No 2 (2016): INFOTEKNIK VOL. 17 NO. 2 2016 Vol 17, No 1 (2016): INFOTEKNIK Vol. 17 No. 1 2016 2016: Prosiding Semnas Teknik Sipil 2016 Vol 16, No 2 (2015): INFOTEKNIK VOL. 16 NO. 2 2015 Vol 16, No 1 (2015): INFOTEKNIK VOL. 16 NO. 1 2015 2015: Prosiding Semnas Teknik Sipil 2015 Vol 15, No 2 (2014): INFOTEKNIK VOL. 15 NO. 2 2014 Vol 15, No 1 (2014): INFOTEKNIK VOL. 15 NO. 1 2014 Vol 14, No 2 (2013): INFOTEKNIK VOL. 14 NO. 2 2013 Vol 14, No 1 (2013): INFOTEKNIK VOL. 14 NO. 1 2013 Vol 13, No 2 (2012): INFOTEKNIK VOL. 13 NO. 2 2012 Vol 13, No 1 (2012): INFOTEKNIK VOL. 13 NO. 1 2012 Vol 12, No 2 (2011): INFOTEKNIK VOL. 12 NO. 2 2011 Vol 12, No 1 (2011): INFOTEKNIK VOL. 12 NO. 1 2011 Vol 11, No 1 (2010): INFOTEKNIK VOL. 11 NO. 1 2010 Vol 10, No 1 (2009): INFOTEKNIK VOL. 10 NO. 1 2009 Vol 9, No 2 (2008): INFOTEKNIK VOL. 9 NO. 2 2008 Vol 8, No 2 (2007): INFOTEKNIK VOL. 8 NO. 2 2007 Vol 8, No 1 (2007): INFOTEKNIK VOL. 8 NO. 1 2007 Vol 7, No 2 (2006): INFOTEKNIK VOL. 7 NO. 2 2006 Vol 7, No 1 (2006): INFOTEKNIK VOL. 7 NO. 1 2006 Vol 6, No 2 (2005): INFOTEKNIK VOL. 6 NO. 2 2005 Vol 6, No 1 (2005): INFOTEKNIK VOL. 6 NO. 1 2005 Vol 5, No 2 (2004): INFOTEKNIK VOL. 5 NO. 2 2004 Vol 5, No 1 (2004): INFOTEKNIK VOL. 5 NO. 1 2004 Vol 4, No 2 (2003): INFOTEKNIK VOL. 4 NO. 2 2003 Vol 4, No 1 (2003): INFOTEKNIK VOL. 4 NO. 1 2003 Vol 3, No 1 (2002): INFOTEKNIK VOL. 3 NO. 1 2002 Vol 2, No 1 (2001): INFOTEKNIK VOL. 2 NO. 1 2001 Vol 1, No 1 (2000): INFOTEKNIK VOL. 1 NO. 1 2000 More Issue