Claim Missing Document
Check
Articles

Found 9 Documents
Search

KALIBRASI DETEKTOR NaI(Tl) UNTUK PEMANTAUAN KONTAMINASI BAHAN RADIOAKTIF DI TANAH SECARA IN-SITU Sholihuddin, Imam; Noor, Johan A. E.; Bunawas, bunawas
Physics Student Journal Vol 1, No 1 (2013)
Publisher : Department of Physics - Faculty of Science

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

Telah dilakukan kalibrasi terhadap spektrometer gamma dengan detektor NaI(Tl). Kalibrasi ini terdiri dari kalibrasi energi yang menunjukkan hubungan antara energi sinar gamma dengan channel pada sofware portable gamma mapping acquisition, kalibrasi efisiensi yang menunjukkan hubungan antara cacahan spektrometer dengan aktivitas sinar gamma. Kalibrasi energi dilakukan dengan menentukan puncak energi hasil pencacahan sumber titik Co-60 dan Cs-137. Kalibrasi efisiensi dilakukan dengan cara melakukan pencacahan terhadap sumber standar tanah dengan kandungan radionuklida alam dan sumber standar tanah dengan kandungan radionuklida buatan dengan nilai variasi ketinggian detektor yang berbeda antara detektor menggunakan shielding dan detektor tanpa menggunakan shielding. Hubungan energi dengan channel pada software dirumuskan oleh energi = 3,153 channel + 29,97. Nilai faktor koreksi stripping rasio 𝛼 dan 𝛽 untuk detektor menggunakan shielding adalah 0,03 dan 0,60, sedangkan untuk detektor tanpa menggunakan shielding adalah 0,02 dan 0,47. Nilai KMD (Konsentrasi Minimum yang dapat Dideteksi) untuk selang kepercayaan 1σ (68,5%) untuk detektor tanpa menggunakan shielding pada ketinggian 38 cm untuk radionuklida Cs-137 = 4,6 Bq/kg, K-40 = 23,4 Bq/kg, U-238 = 10,3 Bq/kg, Th-232 = 10,1 Bq/kg, sedangkan nilai KMD untuk detektor dengan menggunakan shielding pada ketinggian 23 cm untuk radionuklida Cs-137 = 1,9 Bq/kg, K-40 = 13,8 Bq/kg, U-238 = 5,9 Bq/kg, Th-232 = 5,8 Bq/kg.Kata kunci: kalibrasi, detektor NaI(Tl), energi, efisiensi, dan KMD.
PENGUKURAN KONSENTRASI TIMBAL (Pb) DALAM DEBU DI RUMAH PENDUDUK KAWASAN DESA KADU, KECAMATAN CURUG, TANGERANG – BANTEN Bobu, Fetronela R.; Noor, Johan A.E.; bunawas, Bunawas
Physics Student Journal Vol 1, No 1 (2013)
Publisher : Department of Physics - Faculty of Science

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

The processing industry of ex accu can give bad impact to the air quality. Dust from  industrial activity is one of  main lead exposure (Pb). The aim of this researh is to know  Pb concentration in dust. This research have been done on the resident area at DesaKadu, Tangerang, Banten. The  sample took at three region.  This region is in recycle ex accu industrial area (RT 3a, RT 3b and RT 4a) by total respondents, 51. This research is observational quantitative with cross sectional design. It was look Pb concentration in floor’s dust and sand’s dust in the same period.  The Pb concentration measurement were conducted by X ray Fluorescence (XRF) and to measure supporting variable were conducted by kuisioner. The results show that Pbconcentration in floor’s dust 442-558 μg/ft2 and in sand’s dust 505-5066 μg/ft2. The results show that Pb concentration had out of standard.   Keywords : recycle ex accu industry, dust, lead (Pb), X-ray Fluorescene (XRF)
PENGUKURAN SPEKTRUM dan PAPARAN BREMSSTRAHLUNG dari SUMBER STANDAR BETA Sr-90/Y-90 dan Kr-85 Pradani, Ayu Puspita; Bunawas, Bunawas; Noor, Johan A.E
Physics Student Journal Vol 1, No 1 (2013)
Publisher : Department of Physics - Faculty of Science

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

ABSTRAK Telah dilakukan pengukuran spektrum dan paparan bremsstrahlung dari sumber standar beta 90Sr/90Y dan 85Kr dengan menggunakan spektrometer CdTe xR-100T untuk pengukuran spektrum dan berbagai jenis surveymeter untuk pengukuran paparan. Hasil yang didapatkan dalam penelitian ini untuk spektrum bremsstrahlung dengan sumber terbuka dari 90Sr/90Y didapatkan energi maksimal sebesar 90,85 keV sedangkan 85Kr energi maksimal sebesar 86,78 keV. Sedangkan hasil dari 90Sr/90Y  didapatkan energy maksimal sebesar 89,37 keV dan energi maksimal 85Kr sebesar 86,41 keV. Kemudian untuk hasil paparan bremsstrahlung didapatkan hasil untuk detektor Babyline 61A memiliki hasil pengukuran yang lebih tinggi dibandingkan dengan detektor Inspector dan detektor Atomtek. Hal ini disebabkan karena kemampuan dari detektor yang berbeda-beda. Kemudian hasil pengukuran yang diperoleh dimana spektrum dan paparan bremsstrahlung dari sumber standar beta untuk 90Sr/90Y memiliki radiasi yang lebih tinggi dibandingkan dengan  85Kr. Serta sebagai informasi yang perlu diperhatikan dari bahaya bremsstrahlung bagi para pekerja dalam bidang industri.   Kata kunci: Stronsium-90/Yttrium-90, Krypton-85, Surveymeter dan Spektrometer CdTe xR-100T.
PENGUKURAN PAPARAN DAN DOSIS KEDALAMAN RADIASI BETA DENGAN MENGGUNAKAN EXTRAPOLATION CHAMBER Indriani, Dewi; Noor, Johan A.E; Bunawas, Bunawas
Physics Student Journal Vol 1, No 1 (2013)
Publisher : Department of Physics - Faculty of Science

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

Telah dilakukan penelitian untuk menganalisa paparan dan dosis kedalaman radiasi beta. Penelitian ini dilakukan dengan menggunakan paparan radiasi dan dosis kedalaman dengan menggunakan alat Bohm Extrapolation Chamber. Pengukuran laju paparan radiasi beta dilakukan dengan menggunakan variasi terhadap jarak dan sudut, sementara pengukuran dosis kedalaman radiasi beta dilakukan dengan menggunakan medium Mylar dan PMMA. Dari hasil pengukuran paparan dan dosis kedalaman radiasi beta analisis didapatkan bahwa laju paparan radiasi sumber radiasi beta Sr-90/Y-90 dan Kr-85 yang diperoleh dari sumber bekas industri. Laju paparan radiasi beta untuk sumber Sr-90/Y-90 sebesar 252,79 mGy/h (30 cm) dan 88,12 mGy/h (50 cm) sedangakan untuk sumebr Kr-85 sebesar 93,71 mGy/h (30 cm). Dan dapat dinyatakan bahwa laju dosis radiasi beta bergantung pada jarak dan fungsi sudut.     Kata kunci : radiasi beta, Bohm Extrapolation Chamber, paparan radiasi beta, dosis kedalaman,
Perkiraan Dosis dan Distribusi Fluks Neutron Cepat dengan Simulasi Monte Carlo MCNPX pada Fantom Saat Terapi Linac 15 MV Azizah, Azizah; Abdurrouf, Abdurrouf; Bunawas, Bunawas
Physics Student Journal Vol 2, No 1 (2014)
Publisher : Department of Physics - Faculty of Science

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

Linac (Linear Accelerator) dengan energi di atas 10 MV akan menghasilkan neutron cepat karena terjadi interaksi antara foton dengan inti atom suatu material dengan nomor atom (Z) tinggi. Salah satu metode yang dapat digunakan untuk menghitung dosis neutron cepat yang dihasilkan oleh Linac adalah dengan menggunakan metode simulasi Monte Carlo. Salah satu aplikasi dari kode transport radiasi Monte Carlo yang dapat menghitung dosis dan fluks neutron adalah MCNPX (Monte Carlo N-Particle eXtended). Tujuan dari penelitian ini adalah untuk mengetahui dosis ekivalen dan distribusi fluks partikel neutron pada saat terapi Linac dengan metode simulasi Monte Carlo pada program MCNPX. Fantom disimulasikan menggunakan program MCNPX untuk menentukan dosis pada tiap organ dan ditribusi fluks pada fantom. Simulasi penyinaran dilakukan pada 4 sudut yaitu 0°, 90°, 180°, dan 270°. Hasil dari penelitian ini yaitu diperoleh dosis ekivalen neutron cepat paling tinggi terdapat pada permukaan tubuh yaitu dengan total sebesar 6,32 x10-11 mSv. Sedangkan dosis paling rendah terdapat pada kaki kiri bawah yaitu dengan total sebesar 4,77 x10-13 mSv. Fluks paling tinggi pada penyinaran sudut 0° terdapat pada daerah payudara yaitu sebesar 1,40x10-6 MeV/cm3. Fluks paling tinggi pada penyinaran sudut 90° terdapat pada bagian tubuh sebelah kiri fantom yaitu sebesar 1,60x10-5 MeV/cm3. Fluks paling tinggi pada penyinaran sudut 180° terdapat pada punggung fantom yaitu sebesar 9,00x10-6 MeV/cm3. Fluks paling tinggi pada penyinaran 270° terdapat pada bagian tubuh sebelah kanan fantom yaitu sebesar 1,40x10-5 MeV/cm3.   Kata kunci              : Linac, neutron cepat, simulasi Monte Carlo, MCNPX.
Simulation of TLD-700 (Lif; Mg, Ti) for Determination of Hp Equivalent Dose (10) on Radiation Workers (Gamma) with MCNPX Approach Pradipta, Aisyah Dianing; Rianto, Sugeng; Bunawas, Bunawas
Natural B Vol 4, No 1 (2017)
Publisher : Natural B

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (403.211 KB) | DOI: 10.21776/ub.natural-b.2017.004.01.6

Abstract

Radiation workers are compulsory to monitoring radiation dose for reduce the effects of ionizing radiation on the body. Government through similar BAPETEN maximum dose for radiation workers is 20 mSv/year. One of the personal monitoring tool that is widely used is the TLD-700 (specially for gamma radiation). The equivalent dose to the workers body to a depth of 10mm (Hp(10)) able to be predicted from a simulation approach MCNPX. To simulation needed input model of geometry which adapted to the geometry experiments. The simulation results at the source position vertical to the dose rate is obtained 8,565mSv/h, which shows a difference of 1.5% on the results of the experiment, so the Hp(10) dose can be determined. This experiment able to simulated for contamination source 137Cs on the floor position unable to be done experimentely contamination source. Estimation through simulation, the dose rate on the floor at 14.920 mSv/h. The results showed the difference of dose rate through dose rate 75% vertical source larger than the vertical direction. According to the result need to be calibration TLD-700 for the source position from the bottom. Because the greater the dose rate (from below), the greater the Hp(10) dose is received. With the result clear that considerable potential MCNPX used to estimate personal Hp(10) dose for radiation workers, specially in relation to the case of a radiation accident.
PENENTUAN KONSENTRASI AKTIVITAS URANIUM DARI INDUSTRI FOSFAT MENGGUNAKAN DETEKTOR ZnS(Ag) Setiani, Indri; Munir, Mohammad; Firdausi, K. Sofjan; Bunawas, Bunawas
BERKALA FISIKA Vol 9, No 2 (2006): Berkala Fisika
Publisher : BERKALA FISIKA

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (266.368 KB)

Abstract

The activity concentration measurement of uranium (U238) in yellowcake sample which is coming from  phosphate fertilizer industry P.T. PETRO KIMIA Gresik  by using ZnS(Ag) detector has been done. In order to do this measurement, it is needed to callibrate and calculate the minimum detectable level of the detector. From the five samples that contain different yellowcake concentration, 400 mg of each samples were placed on five 2-inches-diameter stainless steel planchettes. HNO3 solution were added and the samples were shaken in order to make the samples as homogeneous as possible. The samples were totally evaporated under an infrared lamp until dry. Then they were counted by ZnS(Ag) detector. The uranium activity concentration measurement result of this method shows that sample with highest concentration of yellowcake (100%) have concentration activity 2,37 Bq/mg. While the sample with lowest concentration of yellowcake (37,5%) have concentration activity 0,95 Bq/mg. Key words     : uranium, phosphate fertilizer industry, ZnS(Ag) detector, yellowcake
A ZE25A-O3 Sensor-Based Solution for Continuous Ozone Level Measurement in LINAC Environments Khasanah, Nur; Hudha, Lalu Sahrul; Jamiluddin, Jamiluddin; Ernita, Nevi; Bunawas, Bunawas; M, I Wayan Ari; Subroto, Rinarto
Prisma Sains : Jurnal Pengkajian Ilmu dan Pembelajaran Matematika dan IPA IKIP Mataram Vol. 13 No. 4: October 2025
Publisher : Universitas Pendidikan Mandalika

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.33394/j-ps.v13i4.16540

Abstract

Abstract Ozone (O₃) generated during LINAC operation can accumulate indoors and pose respiratory risks, yet many facilities lack continuous monitoring. We designed and validated a low-cost, electrochemical sensor platform—ZE25A-O₃ integrated with an Arduino Mega, on-board logging, and a Nextion HMI—for real-time surveillance in a LINAC suite. The sensor was calibrated at 24 °C and 40% RH against 0.5–1.5 ppm standards, yielding slope = 1.045, intercept = −0.04067 ppm, R² = 0.99984, and RMSE = 9.39 ppb, supporting reliable low-ppb quantification. Time series were aggregated into 30-min bins with centered 1-h rolling means to extract diurnal structure while suppressing short-term fluctuations. Field measurements showed a 20–30 ppb background with intermittent spikes exceeding 100 ppb (peaks ~150 ppb). A reproducible daily pattern emerged: late-morning minima (~20–21 ppb) followed by evening enhancement (~26–28 ppb), consistent with ventilation and operational schedule. Average conditions were below the Indonesian workplace limit of 100 ppb, but episodic exceedances motivate real-time alerts and ventilation management. This work demonstrates a practical approach for continuous exposure assessment and data-informed environmental control in radiotherapy facilities.
Efek Variasi Arus Waktu Terhadap Dosis Efektif Radiasi Lensa Mata Pada Penggunaan Bismuth Shielding Pada CT-Scan Kepala Sihaloho, Monika Lestari; Sandi, Nengah; Bunawas, Bunawas; Irhas, Rozi
Kappa Journal Vol 7 No 1 (2023): April
Publisher : Universitas Hamzanwadi

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.29408/kpj.v7i1.15995

Abstract

A study has been carried out to determine the effect of time current variation on the effective dose of eye lens radiation on head CT scans. The aim of this study was to determine the effect of changing the flow of time on the effective dose of eye lens radiation and to determine the reduction in the effective dose of eye lens radiation when using bismuth shielding. The tools used are CT-scan, head mannequin, thermoliminescence dosimeter (TLD) calcium sulfate CaSO4;Dy, and bismuth shielding. The method used in this study uses the calculation of the effective dose of the 100 kV calibration curve from NuclindoLab and the equivalent dose. The measurement results show an average of each current of 31.540 mSv 100 mAs 43.947 mSv 150 mSv 59.808 msv 200 mAs 64.747 mSv 250 mAs, 137.083 mSv 300 mAs without bismuth and using bismuth 26.883 mSv 100 mAs 100 mAs, 27.847 mSv 27.84 mSv 200 mAs, 50.430 mSv 250 mAs, 81.334 mSv 300 mAs. Based on the results obtained, it is known that the effective dose obtained in the eye lens without bismuth is 67.42 ± 39.41 mSv and using bismuth is 48.85 ± 22.43 mSv with a dose reduction of 27%. As for efforts to reduce the dose received, it must be done by paying attention to the parameter settings on the CT-Scan examination such as voltage, current, slice thinkness, pitch and the use of protective equipment such as bismuth shielding.