Claim Missing Document
Check
Articles

Found 33 Documents
Search

ANFIS-Controlled High Step Up DC DC Converter for Fuel Cell Systems with Enhanced Efficiency Against Load Variation Harmini Harmini; Mochamad Ashari; Feby Agung Pamuji
Kinetik: Game Technology, Information System, Computer Network, Computing, Electronics, and Control Vol. 11, No. 1, February 2026
Publisher : Universitas Muhammadiyah Malang

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.22219/kinetik.v11i1.2456

Abstract

The primary challenge in utilizing Fuel Cell (FC) systems lies in their inherently low and fluctuating output voltage, which contrasts with the requirements of a Direct Current (DC) bus network that demands a stable and relatively high voltage level. Ensuring consistent voltage regulation in the DC bus network is essential for reliable system performance. An interface converter is required to elevate and stabilize the voltage output under dynamic operating conditions. This paper introduces a high step-up DC–DC converter integrated with an Adaptive Neuro-Fuzzy Inference System (ANFIS)-based control scheme for enhancing the performance of FC power systems. The proposed work encompasses the modeling, analytical design, and structural development of the converter and its intelligent control mechanism. The proposed high step-up converter exhibits a novel structural configuration that integrates a clamp unit, a Multiplier Cell (MC), and cascaded Quadratic Boost Converter (QBC) stages. The contribution of this converter topology lies in its ability to enhance the reliability of fuel cell–based renewable energy systems, achieve high voltage amplification, ensure optimal efficiency, and maintain dynamic stability. This topology is specifically developed to attain an ultra-high voltage conversion ratio, achieving a significant voltage gain of up to 9.65 times, thereby effectively increasing the input voltage from 45 V to 400 V. The ANFIS controller effectively maintains a stable output voltage of 400 V with a maximum deviation of only ±3.5%. The proposed converter achieves a peak efficiency of 87% under varying load conditions, demonstrating its suitability for fuel cell-based energy systems.
OPTIMAL DESIGN OF BLDC MOTOR USING ABO (AFRICAN BUFFALO OPTIMIZATION) ALGORITHM TO MINIMIZE COGGING TORQUE Irfan Ubaidillah; Feby Agung Pamuji; Hery Suryoatmojo
JAREE (Journal on Advanced Research in Electrical Engineering) Vol. 10 No. 1 (2026): January
Publisher : Department of Electrical Engineering ITS and FORTEI

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.12962/jaree.v1i10.546

Abstract

The use of BLDC motors in recent years has shown rapid development. This is motivated by efforts to reduce pollution with renewable energy. On the other hand, the advantages of BLDC motors have their own appeal so that they are widely applied not only in the automotive, health but also in the fields of aerospace and household appliances. The BLDC motor design that uses permanent magnets makes it produce good characteristics in power distribution, torque, and efficiency. However, it is not uncommon for the BLDC motor design to also create ripples in torque caused by cogging torque, causing unsmooth torque distribution, vibration and noise. The stator design in BLDC motors is the main factor causing the high cogging torque that occurs. This is due to the difference in flux density in the air gap and the interaction of magnets with the stator surface. This research focuses on reducing cogging torque by optimizing these parameters using the African Buffalo Optimization (ABO) method. The research was conducted by modeling the phenomenon of cogging torque through mathematical calculations and optimization through MATLAB. The optimized parameters are then simulated with MOTOR-CAD software to be analyzed and evaluated.
Life Cycle Cost Analysis of PV-Wind-Battery Hybrid Power System at PLN Nusantara Power Brantas Generation Unit Tulungagung Alfian Budiarmoko; Heri Suryoatmojo; Feby Agung Pamuji
JAREE (Journal on Advanced Research in Electrical Engineering) Vol. 10 No. 1 (2026): January
Publisher : Department of Electrical Engineering ITS and FORTEI

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.12962/jaree.v1i10.550

Abstract