Claim Missing Document
Check
Articles

Found 39 Documents
Search

Perancangan Kapal Tanpa Awak Dengan Pengendali Otomatis dan Kontrol Jarak Jauh Samidun, Samidun; Sudarsono, Sudarsono; Endriatno, Nanang
Enthalpy : Jurnal Ilmiah Mahasiswa Teknik Mesin Vol 8, No 2 (2023): Enthalpy: Jurnal Ilmiah Mahasiswa Teknik Mesin
Publisher : Teknik Mesin Universitas Halu Oleo

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.55679/enthalpy.v8i2.34366

Abstract

The development of science and technology in the maritime field is increasing marked by the rapid progress that occurs with the creation of increasingly sophisticated equipment. However, the development of unmanned ship technology is still not widely applied in Indonesia, so it is necessary to develop further technology on unmanned ship technology so that it can be applied in Indonesia, both in the military, commercial and so on. For that we designed an unmanned ship without a remote control automatic control. In this remote control automatic ship program, there are two main programs, namely the transmitter/sender program, where this program is used to program the remote control, while the receiver/receiver program is used on the ship to be steered, and to connect the transmitter and receiver. using the nRF25L01 module. The workings of this tool is that when potentiometer 1 is read it will move the servo motor, and if potentiometer 2 is read, it will move the Brushed Motor through the ESC. The comparison results at an angle of 45°, the track diameter is 145.33 cm, with a time of 5.59 seconds and a speed of 26.02 cm/s. At an angle of 30°, the track diameter is 226.67 cm, with a time of 9.51 seconds and a speed of 23.80 cm/s. While at an angle of 15°, the track diameter is 331.33 cm, with a time of 15.52 seconds and a speed of 21.36 cm/s.Keywords: Unmanned Ship, nRF24L01, Potentiometer
Analisa Kekuatan Mekanik Sambungan Las Menggunakan Pola Ayunan Melingkar Dan Zig-Zag Pada Baja Karbon Sedang Irwan, Irwan; Endriatno, Nanang; Hasanudin, La
Enthalpy : Jurnal Ilmiah Mahasiswa Teknik Mesin Vol 7, No 4 (2022): Enthalpy: Jurnal Ilmiah Mahasiswa Teknik Mesin
Publisher : Teknik Mesin Universitas Halu Oleo

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.55679/enthalpy.v7i4.28405

Abstract

Welding is one of the metal joining techniques by melting some of the parent metal and filler metal which is currently widely used with different methods and movements of welding electrodes. These methods aim to obtain flat and smooth welds and at the same time become the impetus for the compilers to conduct research entitled "analysis of the mechanical strength of welded joints using circular and zig-zag swing patterns on medium carbon steel" with the aim of knowing the effect of welding patterns on hardness test on medium carbon steel material and the effect of microstructure welding pattern on medium carbon steel material. This research was conducted in August 2020, at the Mechanical Engineering Materials and Technology Laboratory, Department of Mechanical Engineering, Faculty of Engineering, Halu Oleo University Kendari. The tools used are welding machines, grinding machines, welding goggles, pliers, masks and gloves while the materials are 0.5 cm carbon steel plate, welding electrodes, grinding wheels. The results of the first research are that for welding using a circular electrode movement pattern which shows a softer or more ductile result, while for a harder or brittle result, it is shown in the zigzag electrode movement welding process and secondly that the circular electrode movement in the welding process has an impact on the microstructure. in the HAZ area which is getting darker because the structure formed is dominated by pearlite, while in welding the zigzag electrode movement has an impact on the HAZ area which is getting brighter because it is dominated by the bainite structureKeywords: Circular Welding Pattern, Mechanical Strength, Medium Carbon Steel, Zigzag Welding Pattern,
Pengaruh Penambahan Slag Nikel Dan Cacahan Plastik Terhadap Kekuatan Tekan Paving Block Huzaifa, Huzaifa; Endriatno, Nanang; Kadir, Abd.
Enthalpy : Jurnal Ilmiah Mahasiswa Teknik Mesin Vol 6, No 1 (2021): Enthalpy: Jurnal Ilmiah Mahasiswa Teknik Mesin
Publisher : Teknik Mesin Universitas Halu Oleo

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (279.156 KB) | DOI: 10.55679/enthalpy.v6i1.19127

Abstract

This study aims to analyze the addition of nickel slag and crushed plastic into the paving block on the compressive strength. Paving blocks were made by conventional methods. Samples were made and tested according to SNI 03-0691-1996 standards. After molded, the paving blocks were dried within 28 days. After that, the materials were placed on a compression test device to determine the compressive strength. The results of the compression test showed that the maximum compressive strength value was owned by sample B with a value of 210.8 kg/cm2 with a volume composition of 25% cement, 5% coarse aggregate, 30% nickel slag, 5% fine aggregate, and 35% crushed plastic. The minimum compressive strength was found in sample A with a value of 129.17 kg/cm2 with a mixture composition of 25% cement, 25% coarse aggregate and 50% fine aggregate. From this study, it was found that there was an increase in the compressive strength of the paving block after the addition of chopped plastic and nickel slag.Keywords: paving block, slag nickel, plastic chopping, compressive strength
Analisis Getaran Balok Komposit Fiberglass Dengan Variasi Tumpuan Jepit-Jepit, Jepit-Bebas, dan Jepit-Rol Marwin, Marwin; Endriatno, Nanang; Sisworo, Raden Rinova
Enthalpy : Jurnal Ilmiah Mahasiswa Teknik Mesin Vol 8, No 3 (2023): Enthalpy: Jurnal Ilmiah Mahasiswa Teknik Mesin
Publisher : Teknik Mesin Universitas Halu Oleo

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.55679/enthalpy.v8i3.41833

Abstract

Vibration is an alternating motion through its equilibrium point caused by a disturbance or deviation. This study aims to determine the value of vibrational displacement in fiberglass composite beams supported by fixed-fixed, fixed-free, and fixed-roll. The research method includes the design of a vibration test tool made of U-profile steel. The test material uses a composite beam measuring 1000 mm x 25 mm x 25 mm. variations in the placement of the exciter are 10 cm, 25 cm, 40 cm, 55 cm, and 70 cm. the result of the study were obtained on the support of the fixed-fixed the highest deviation value was at a distance of 25 cm, namely 0.193 mm, and the lowest value at a distance of 70 cm, namely 0.096 mm. On the fixed-free support the highest deflection value is at a distance of 70 cm which is 0.455 mm, and the lowest value is at a distance of 10 cm which is 0.133 mm. And while on the fixed-roll pile the highest deviation value is at a distance of 10 cm, which is 0.123 mm. Kata kunci: vibration, displacement, composite, support variation.
Desain dan Analisa Mesin Pencacah Nilam Dengan Kapasitas 200 Kg/Jam Miswan, Miswan; Salimin, Salimin; Endriatno, Nanang
Enthalpy : Jurnal Ilmiah Mahasiswa Teknik Mesin Vol 6, No 4 (2021): Enthalpy: Jurnal Ilmiah Mahasiswa Teknik Mesin
Publisher : Teknik Mesin Universitas Halu Oleo

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (618.06 KB) | DOI: 10.55679/enthalpy.v6i4.22573

Abstract

The Southeast Sulawesi region, which is the East Kolaka area, especially the AERE sub- district, AERE village is an area whose livelihood is in agriculture. One of them is patchouli farming.  In  processing  patchouli,  most  still  use  traditional  methods.  This  makes  the patchouli processing process less efficient, so researchers want to create a tool that can make patchouli processing to save costs. Patchouli chopping machine is an important tool  in  improving  the  observation  of  patchouli  farming.  The  working  principle  of  this machine utilizes the power of a gasoline motor. Through the Puly mechanism and the V- belt produced by the gasoline motor, it will be transferred to the shaft which is connected to the blade. The stages of design and calculation on the patchouli chopping machine consist of calculating the design power, calculating the shaft, calculating the shear stress, torsional  moment  of  the  plan,  designing  the  blade  by  taking  into  account  the characteristic data of patchouli, the average patchouli volume and patchouli mass (ms). . Based on the results of the calculation of the characteristics of the patchouli plant with an average height of patchouli 150 cm, diameter of the main stem 12.79 mm and density of 0.112 g cm, it can be concluded that the power of the gasoline motor used is 6.5 hp with a shaft rotation of n1 3600 rpm , the design power obtained on the shaft design of the  patchouli  chopping  machine  is  9.554  (kw),  the  shear  stress  on  the  shaft  is  1.646 kg/mm², the compressive strength of the slicing knife is 36.2044512 N, with a shear stress of 0.1153008 N/mm².Keywords: Design, analysis, crusher machine,patchouli   
Analisis Perancangan Alat Pencacah Nilam Untuk Petani Nilam Prananda, Fijay; Balaka, Ridway; Endriatno, Nanang
Enthalpy : Jurnal Ilmiah Mahasiswa Teknik Mesin Vol 9, No 1 (2024): Enthalpy: Jurnal Ilmiah Mahasiswa Teknik Mesin
Publisher : Teknik Mesin Universitas Halu Oleo

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.55679/enthalpy.v9i1.46935

Abstract

The automatic pull shaft on the patchouli chopper is an important component of the patchouli chopper machine. The research aims to carry out an analysis of the patchouli chopper pull shaft and produce a design for the newest patchouli chopper. In this research, the focus was only on the analysis of the pulling shaft on the patchouli chopper where all research methodologies were carried out using inventor software. The main driving engine is a combustion engine with a power of 5.5 HP, S45C shaft material with a tensile strength of 58 kg/mm2, and a shaft diameter of 15 mm. In the selection of pulleys, plays with diameters of 50 mm and 300 mm are used, V - Belt speed is 0.18 m/s, circumference length is 1499 mm, using V - Belt type B with axle distance of 474.6 mm, the contact angle is 2.3 rad and the length of the chopped patchouli was 3.8 cm. From the calculations and analysis, the addition of a pulling shaft to the patchouli chopper is safe to use. Keywords: Patchouli chopping tool, Puller shaft, Patchouli
Perencanaan Alat Uji Impact Type Charpy Kapasitas 10 Joule Saktiawan, Saktiawan; Endriatno, Nanang; Imran, Al Ichlas
Enthalpy : Jurnal Ilmiah Mahasiswa Teknik Mesin Vol 5, No 4 (2020): Enthalpy: Jurnal Ilmiah Mahasiswa Teknik Mesin
Publisher : Teknik Mesin Universitas Halu Oleo

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (597.398 KB) | DOI: 10.55679/enthalpy.v5i4.15765

Abstract

In  the  implementation  of  construction  and  material  engineering,  the  choice  of materials  for  metal  material  needs  is  very  important.  The  research  objectives were planning the pendulum, swing shaft, the frame for the Charpy type impact test,  and  planning  the  test  specimen  holder.  The  research  method  includes planning  the  pendulum,  shaft,  arm,  bearing,  pole  frame  and  specimen  holder (anvil), as well as selecting materials and calculating the strength of the materials. The results of the research. The impact test tool uses a pendulum made of steel ST 37 with a pendulum length = 0.345 mm, volume = 213 mm3, mass = 1.67 kg, in the planning of the shaft, with the results of the planning calculation obtained the diameter of the shaft = 25.4 mm, while the moment torque obtained = 577,219 kg mm, in the planning of the Charpy type impact test, the frame uses C-profile steel with  a  size  of  125  x  65,  the  material  is  chosen  because  its  width  exceeds  the bearing holder, for tangsial force = 28,951 N, bending moment = 5240.1 N mm , cross-sectional  modulus  =  109.169  mm3,  the  specimen  holder  planning  must exceed  the  specimen  width  itself  so  that  the  specimen  can  be  placed  properly, the allowance = 1.206 mm2 and the planning of the impak test tool for the 10 J tool can be used to test plastic materials with an impact energy below 10 J, with a height of 610 ± 2 mm. Keywords:  Construction,  Materials  Engineering,  Metal  Materials,  Iron,  Steel, Impak. 
Analisa Pengaruh Excess Air Terhadap Efisiensi Pembakaran Boiler Jenis Pulverizer Coal 230 T/H Muholad, Wildan; Hasbi, Muhammad; Endriatno, Nanang
Enthalpy : Jurnal Ilmiah Mahasiswa Teknik Mesin Vol 6, No 3 (2021): Enthalpy: Jurnal Ilmiah Mahasiswa Teknik Mesin
Publisher : Teknik Mesin Universitas Halu Oleo

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (571.264 KB) | DOI: 10.55679/enthalpy.v6i3.20979

Abstract

To save on coal consumption in PLTU (Steam Power Plant), it is necessary to increase boiler efficiency. The factors that can affect boiler efficiency include: flue gas temperature, fuel specification, excess air, ambient temperature, radiation and convection losses. By changing the value of excess air in this case the percentage of oxygen (4% to 4.5%) will affect the efficiency of the boiler. Changing the value of excess air also results in a change in the electrical power used by the auxiliary system in the boiler. Calculation of boiler efficiency with the direct method by testing 2 times on each oxygen percentage value of 4% and 4.5. Efficiency increased 0.94%, from 80.76% to 81.7% in test 1 and increased 1.02%, from 90.81% to 91.83% in test II. The power usage increased by 27.959 Kw in the 1st test and increased to 26.663 Kw in the test II.Kata kunci: Boiler, efficiency, excess air, PLTU
Pengaruh Pola Susunan Laminasi Terhadap Distribusi Tegangan Dan Regangan Tarik Pada Komposit CFRP Yang Berlubang Alfian, Hamzah; Sudarsono, Sudarsono; Endriatno, Nanang
Enthalpy : Jurnal Ilmiah Mahasiswa Teknik Mesin Vol 6, No 3 (2021): Enthalpy: Jurnal Ilmiah Mahasiswa Teknik Mesin
Publisher : Teknik Mesin Universitas Halu Oleo

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (607.389 KB) | DOI: 10.55679/enthalpy.v6i3.20973

Abstract

The development of material technology is growing rapidly, especially in the manufacturing industry. One of the materials that are most often used and developed today is composite materials. The purpose of this study was to determine the effect of the pattern of laminate arrangement on the distribution of stress and tensile strain in perforated CFRP composites. The research method carried out is tensile testing using abaqus software, the specimen is designed with 8 laminates and the fiber direction is varied. The specimens were made with the ASTM D 5766 test standard and the properties used were carbon fiber composite type T800S/3900-2B. From the tensile test simulation results, it is found that the highest stress value in the composite with variations in fiber direction 0°, 45°, -45°, 90°, 90°, -45°, 45°, 0° the maximum stress value reaches 356.9 N/ mm², while the smallest stress occurs in the composite fiber direction 0°, 0°, 0°, 0°, 0°, 0°, 0°, 0° with the maximum stress value reaching 165.7 N/mm. The highest stress and strain that occurs in each specimen is located at the edge of the hole perpendicular to the direction of the force, the stress and strain increase based on variations in the direction of the fiber in the composite, the farther the orientation of the fiber direction to the direction of the applied force, the greater the stress concentration that occurs also.Keywords: Tensile test, CFRP composite, abaqus software
Analisa Pengaruh Variasi Jumlah Nozzle Dengan Memanfaatkan Ketinggian Aliran Air Terhadap Daya Listrik Yang Dihasilkan Turbin Pelton Yasir, La Ode; Balaka, Ridway; Endriatno, Nanang
Enthalpy : Jurnal Ilmiah Mahasiswa Teknik Mesin Vol 7, No 3 (2022): Enthalpy: Jurnal Ilmiah Mahasiswa Teknik Mesin
Publisher : Teknik Mesin Universitas Halu Oleo

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (536.77 KB) | DOI: 10.55679/enthalpy.v7i3.26504

Abstract

The performance of a Pelton turbine is influenced by the height, flow velocity, blade angle, number of nozzles, flow size and number of blades and nozzle spray distance. The purpose of this study was to determine the effect of variations in the number of nozzles and nozzle angles on the power produced by the PRLton turbine. The test results show that the more nozzles used, the greater the power generated and the smaller the nozzle angle, the greater the power generated. In position I using 1 nozzle, at an angle of 25o the electrical power produced is 6.16 Watt, at an angle of 30o the electric power produced is 2.65 Watt, at an angle of 45o the electrical power generated is 0.1 Watt. While in position II using 2 nozzles, , at an angle of 25o the electrical power produced is 7.56 Watts, at an angle of 30o the electrical power generated is 3.76 Watts, at an angle of 45o the electrical power generated is 0.24 Watts.Keywords: Electric power, Nozzle, Pelton turbine