Claim Missing Document
Check
Articles

Found 28 Documents
Search

Biodiesel Production from Vegetable Oil over Plasma Reactor: Optimization of Biodiesel Yield using Response Surface Methodology Istadi Istadi; Didi Dwi Anggoro; Putut Marwoto; Suherman Suherman; Bambang Tri Nugroho
Bulletin of Chemical Reaction Engineering & Catalysis 2009: BCREC Volume 4 Issue 1 Year 2009 (June 2009)
Publisher : Masyarakat Katalis Indonesia - Indonesian Catalyst Society (MKICS)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.9767/bcrec.4.1.7115.23-31

Abstract

Biodiesel production has received considerable attention in the recent past as a renewable fuel. The production of biodiesel by conventional transesterification process employs alkali or acid catalyst and has been industrially accepted for its high conversion and reaction rates. However for alkali catalyst, there may be risk of free acid or water contamination and soap formation is likely to take place which makes the separation process difficult. Although yield is high, the acids, being corrosive, may cause damage to the equipment and the reaction rate was also observed to be low. This research focuses on empirical modeling and optimization for the biodiesel production over plasma reactor. The plasma reactor technology is more promising than the conventional catalytic processes due to the reducing reaction time and easy in product separation. © 2009 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0)
Potential of LiNO3/Al2O3 Catalyst for Heterogeneous Transesterification of Palm Oil to Biodiesel Istadi Istadi; Bambang Pramudono; Suherman Suherman; Slamet Priyanto
Bulletin of Chemical Reaction Engineering & Catalysis 2010: BCREC Volume 5 Issue 1 Year 2010 (June 2010)
Publisher : Masyarakat Katalis Indonesia - Indonesian Catalyst Society (MKICS)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.9767/bcrec.5.1.7128.51-56

Abstract

Production of biodiesel through transesterification process using heterogenous catalysts in order to avoid the saponification problem was studied. In this process, palm oil reacted with methanol to form a mixture of glycerol and biodiese over a solid basic catalyst. One type of the catalysts used in this research is basic catalyst of LiNO3/Al2O3. The parameters studied in this research are concentration of LiNO3 loading on Al2O3 and effect of different reaction time. The products was analyzed using Gas Chromatography to determine composition and yield of resulted methyl esters as well as conversion of palm oil to biodiesel. The major products in this transesterification reaction were biodiesel and glycerol. It can be concluded that the 20 wt% LiNO3/Al2O3 catalyst is potential for producing biodiesel from palm oil over transesterification reaction. Advantages of the usage of this catalyst is that the soap formation was not observed in this research. © 2010 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0)
Life Cycle Assesment pada Proses Distribusi BBM di PT Pertamina Patra Niaga Integrated Terminal Panjang Reza Ismail Alqindy; Suherman Suherman; Tri Retnaningsih Soeprobowati; Yusep Sopian
Jurnal Ilmu Lingkungan Vol 22, No 4 (2024): July 2024
Publisher : School of Postgraduate Studies, Diponegoro Univer

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.14710/jil.22.4.904-913

Abstract

PT Pertamina Patra Niaga Integrated Terminal Panjang mendistribusikan BBM sebesar 2.243.016,58 kiloliter (KL) pada tahun 2022. Dari proses distribusi BBM berpotensi menimbulkan dampak lingkungan yaitu dampak pencemaran udara dimana proses distribusi BBM banyak memakai transportasi berbahan bakar fossil. Penelitian ini bertujuan menganalisis dampak lingkungan dari proses distribusi BBM PT Pertamina Patra Niaga Integrated Terminal Panjang menggunakan metode life cycle assesment (LCA) dengan ruang lingkup gate to gate dimulai dari proses penerimaan BBM hingga pendistibusian BBM. Metode penelitian ini mengacu pada SNI ISO 14040:2016 dan SNI ISO 14044:2017, analisis inventori, penilaian dampak, dan interpretasi. Penilaian dampak dilakukan menggunakan software  SimaPro 9.5.0 dengan metode CMIL IA Baseline dengan unit fungsi adalah 1 KL BBM. Kategori dampak yang dikaji pada penelitian ini yaitu kategori dampak utama berdasarkan Peraturan Menteri Lingkungan Hidup dan Kehutanan Nomor 1 Tahun 2021 tentang Program Penilaian Peringkat Kinerja Perusahaan dan Pengelolaan Lingkungan Hidup, yaitu potensi pemanasan global, potensi penipisan ozon, potensi hujan asam, dan potensi eutrofikasi. Dari masing – masing potensi dampak, terdapat dua isu penting (hotspot) yaitu dari proses distribusi dari penggunaan solar yang menghasilkan nilai karaterisasi potensi pemanasan global sebesar 6,77E+00 kg CO2 ek/KL, potensi penipisan ozon sebesar 1,30E-07 Kg CFC-11 ek/KL, dan potensi hujan asam  sebesar 1,18E-02 Kg SO2 ek/KL. Untuk potensi eutrofikasi isu penting (hotspot) disebabkan oleh proses penyaluran dari penggunaan listrik dengan menghasilkan nilai dampak eutrofikasi sebesar 2,78E-03 Kg PO4 ek/KL. Rekomendasi perbaikan yang dapat diberikan adalah penggunaan transportasi ramah lingkungan dan melakukan gerakan hemat energi atau mengganti penggunaan listrik dari PLN dengan energi terbarukan seperti menggunakan panel surya.
Energy Analysis and Economy Performance of a Hybrid Solar Dryer for Drying Coffee Suherman Suherman; Hadiyanto Hadiyanto; Nicholas Franz; Vimala Kamandjaja; Tubagus Rayyan Fitra Sinuhaji
Jurnal Sains Materi Indonesia Vol. 26 No. 1 (2024): Jurnal Sains dan Materi Indonesia
Publisher : BRIN Publishing (Penerbit BRIN)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.55981/jsmi.2024.3135

Abstract

This work studies the effect of the drying temperature on the profile of the water content, drying rate, drying efficiency, economic performance, and the quality of Robusta and Arabica coffee beans using the hybrid solar dryer. The drying instrument with the help of LPG heating is used in this research with a specified temperature of 40 ℃, 50 ℃, and 60 ℃. The research is conducted on a sunny day for 1 day for each temperature and coffee beans. The temperature profile shows that the lowest water content in the study is 60 ℃. The drying rate for both 50 ℃ and 60 ℃ are similar and the highest average efficiency of the instrument is at 50 ℃ for both Robusta and Arabica beans. The dominant peak in GCMS analysis result of coffee samples was caffeine with a total area percentage of 30.89%, the description of the coffee bean structure using SEM test resulted in a hole size of 5-10 µm, the obtained fat content was 1.6%, the obtained protein content 17.3%. A hybrid solar dryer is an environmentally friendly solution that enables faster coffee drying, with a payback period of 1.5 years for both coffee bean types.
PEMBUATAN SLOW RELEASE FERTILIZER DENGAN MENGGUNAKAN POLIMER AMILUM DAN ASAM AKRILAT SERTA POLIVINIL ALKOHOL SEBAGAI PELAPIS DENGAN MENGGUNAKAN METODA FLUIDIZEDBED Yenni, Afri; ,, Suherman; Purbasari, Aprilina
Prosiding Seminar Nasional Sains dan Teknologi Vol. 15 No. 1 (2025): Prosiding SNST 15 Tahun 2025
Publisher : Fakultas Teknik Universitas Wahid Hasyim

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

Pembuatan Slow release fertilizer bertujuan untuk meningkatkan efisiensi penggunaan pupuk terhadap laju  pelepasan unsur-unsur nutrisi pupuk pada tanaman. Dalam studi ini dilakukan pembuatan slow release fertilizer dengan menggunakan asam akrilik dan polivinil alkohol (PVA) yang masing-masing dicampur dengan amilum dan Polietilen glikol  (PEG) sebagai bahan tambahan pelapis dengan menggunakan metoda fluidized bed spraying coating (FBSC). Variable yang dipelajari konsentrasi polimer  akrilik/amilum (18 %/0-2 %) dan PVA/amilum (3 %/0-2 %) sedangkan berat PEG yang ditambahkan pada masing-masing campuran adalah 1 gram dan suhu udara bed (pengeringan) (35-55 oC) terhadap kualitas produk urea yang terlapisi yakni efisiensi pelapisan, dissolution rate, persen dustiness, dan Scanning Electron Microscopy (SEM). Berdasarkan hasil penelitian didapatkan bahwa efisiensi pelapisan urea dengan akrilik/amilum (18/2 %) pada suhu 40oC adalah 14,4 % sedangkan PVA/amilum (3/2 %) adalah 5,2 %.  Efisiensi pelapisan meningkat dengan meningkatnya konsentrasi pelapis dan berkurang jika terjadi peningkatan suhu bed. Hal yang sama terjadi pada dissolution rate, dimana jika konsentrasi pelapis meningkat maka  dissolution rate  akan meningkat kebalikan terhadap suhu bed, suhu bed meningkat maka  dissolution rate  menurun. Dustiness produk meningkat dengan meningkatnya suhu  bed serta konsentrasi pelapis. Pada analisa SEM pelapis urea dengan menggunakan akrilik morfologi lebih bagus dibandingkan dengan PVA. Kata Kunci: Slow Release Fertilizer, akrilik, PVA, amilum, urea, Fluidized Bed Spray
ENVIRONMENTAL IMPACT ASSESSMENT IN HYDROPOWER GENERATION: A LIFE CYCLE ASSESSMENT AT PT PLN NUSANTARA POWER UP CIRATA, PURWAKARTA, INDONESIA Rimala Zahra Wibowo; Suherman; Muhammad Helmi; Arti Hapsari
Multidiciplinary Output Research For Actual and International Issue (MORFAI) Vol. 6 No. 3 (2026): Multidiciplinary Output Research For Actual and International Issue
Publisher : RADJA PUBLIKA

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.5281/zenodo.19080911

Abstract

PT PLN Nusantara Power UP Cirata is one of the largest hydropower plants in Indonesia, with an installed capacity of 1.008 MW, and plays a strategic role in supporting national electricity supply security. Although classified as renewable energy, hydropower operations are not entirely free from environmental impacts, including greenhouse gas emissions from biomass decomposition in the reservoir and waste generated from turbine and generator maintenance. This study aims to analyze the environmental impacts of electricity generation using the Life Cycle Assessment method with a cradle-to-gate system boundary. The assessment was conducted using SimaPro 9.5.0.2 with the CML-IA Baseline method, where the functional unit was 1 kWh of electricity. The main hotspot within the cradle boundary is the Cirata Reservoir due to diesel consumption, contributing 1.21E-04 kg CO2-eq/kWh to global warming potential, 2.35E-11 kg CFC-11-eq/kWh to ozone depletion potential, 3.52E-07 kg SO2-eq/kWh to acidification potential, and 3.32E-06 kg PO4-eq/kWh to eutrophication potential. Within the gate boundary, hotspots were identified in the turbine, where used oil contributed 1.91E-05 kg CO2-eq/kWh to global warming potential, turbine oil contributed 2.63E-12 kg CFC-11-eq/kWh to ozone depletion and 3.97E-08 kg SO2-eq/kWh to acidification potential, and the sewage treatment plant contributed 3.49E-07 kg PO4-eq/kWh to eutrophication potential.
Energy Efficient Dryer with Rice Husk Fuel for Agriculture Drying M. Djaeni; N. Asiah; S Suherman; A. Sutanto; A. Nurhasanah
International Journal of Renewable Energy Development Vol 4, No 1 (2015): February 2015
Publisher : Center of Biomass & Renewable Energy (CBIORE)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.14710/ijred.4.1.20-24

Abstract

Energy usage is crucial aspect on agriculture drying process. This step spends about 70% of total energy in post harvest treatment. The design of efficient dryer with renewable energy source is urgently required due to the limitation of fossil fuel energy. This work discusses the performance of air dehumidification using rice husk fuel as heat source for onion, and paddy drying. Unlike conventional dryer, the humidity of air during the drying was dehumidified by adsorbent. Hence, the driving force of drying can be  kept high.  As consequences, the drying time and energy usage can be reduced. Here, the research was conducted in two step: laboratory and pilot scale tests. Results showed that the lowering air humidity with rice husk fuel has improved the energy efficiency. At operational temperature 60oC, the heat efficiency of 75%  was achieved. 
Drying turmeric slices using a photovoltaic ventilation direct solar dryer: Drying characteristics and interactions of heat and mass transfer Bambang Waluyo Hadi Eko Prasetiyono; Suherman Suherman; Bakti Jos; Muhammad Anas Asy-Syaqiq
International Journal of Renewable Energy Development Vol 15, No 5 (2026): September 2026
Publisher : Center of Biomass & Renewable Energy (CBIORE)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.61435/ijred.2026.61059

Abstract

This study compares the drying characteristics and the heat and mass transfer phenomena while drying turmeric slices using a photovoltaic ventilation direct solar dryer and open sun drying. Turmeric slices of varying thicknesses—5, 7, and 10 mm—were dried from 83.48% to a final moisture content of 5–6% to ensure safe storage conditions. The drying times required were 1440, 1800, and 2160 min for the direct solar dryer, and 2220, 2520, and 2880 min for open sun drying at 5, 7, and 10 mm thicknesses, respectively. Drying Turmeric slices using the direct solar dryer at thinner thicknesses showed a faster drying rate, with the highest average drying rate observed for the 5 mm slices at 0.287 g/min. Similarly, drying efficiency was higher for thinner slices. The Midilli model provided the best fit for experimental and predicted data in describing the drying kinetics of turmeric slices. The effective moisture diffusivity obtained in this study was 1.65 × 10⁻⁸, 2.66 × 10⁻⁸, and 4.11 × 10⁻⁸ m2/s for the direct solar dryer, and 0.89 × 10⁻⁸, 1.52 × 10⁻⁸, and 2.38 × 10⁻⁸ m2/s for open sun drying at 5, 7, and 10 mm thicknesses, respectively. Higher heat and mass transfer coefficients were observed for drying thinner turmeric slices using the direct solar dryer. The convective heat transfer and evaporative heat transfer coefficients decreased as the moisture content was reduced. In contrast, the mass transfer coefficient increased as the drying time progressed.