Garuda - Garba Rujukan Digital

Simulasi Tegangan (Stress) Pada Komponen Rangka Mesin Uji Tarik Sealent Menggunakan Solidworks Dian Prabowo; Unggul Satria Jati; Ulikaryani Ulikaryani; Probo Hardini
Infotekmesin Vol 14 No 2 (2023): Infotekmesin: Juli, 2023
Publisher : P3M Politeknik Negeri Cilacap

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.35970/infotekmesin.v14i2.1947

A series of processes are carried out in order to obtain the desired product result. One of the processes carried out is testing the strength of polymers by means of tensile testing in this case testing of polymer-based sealants. The method used is the method of simulating frame loading on the tensile testing machine that has been made. The software used to assist the simulation process is SolidWorks. The simulation is carried out in static mode or a fixed loading (no movement or vibration). A stress Analysis Simulation is carried out to get the result of static loading in the form of σ (stress). Loading simulations on the frame of the tensile testing machine for the tensile testing of the sealant are carried out on the components of the frame with different loading variations. Frame components with upward loading are given an average load of 38.5 MPa. Meanwhile, the frame components with downward loading are given an average load of 6.169 MPa. The largest average stress obtained from each component is 0.326 N/mm2. this value does not exceed the yield strength of 235 N/mm2.

Pengaruh Jenis Limbah Aluminium Pada Proses Pengecoran Menggunakan Tungku Krusibel Terhadap Nilai Kekerasannya David Dwi Putra; Faisal Haqqoni; Mohammad Nurhilal; Ulikaryani Ulikaryani
Infotekmesin Vol 14 No 2 (2023): Infotekmesin: Juli, 2023
Publisher : P3M Politeknik Negeri Cilacap

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.35970/infotekmesin.v14i2.1948

Aluminum waste that has accumulated due to the widespread use of aluminum in household needs, daily life, and in the manufacture of industrial material components will have an impact on the environment if not handled properly. It is necessary to utilize aluminum waste in a product that has a sale value through a casting process using a crucible furnace. This research was conducted to determine the hardness differences of waste aluminum from used aluminum cans, used aluminum pots, and used aluminum wires melted in a smelting furnace. This study uses quantitative analysis and experimental research types. Tests carried out on this crucible furnace were carried out to determine the effect of the type of aluminum waste and the length of time it took to smelt the three types of material on the hardness results. The results of the Rockwell hardness test on aluminum can waste have an average value of 71.38 HRB, on aluminum pans waste it has an average value of 71.68 HRB, and on aluminum cable waste it has an average value of 53.02 HRB.

Peningkatan Pengetahuan Peternak Kambing Melalui Penyuluhan Pemeliharaan Ternak di Desa Banjarwaru Pramita, Ayu; Fadlilah, Ilma; Syafirullah, Lutfi; Tarigan, Roy Aries Permana; Ulikaryani, Ulikaryani; Sodikin, Jenal
Nuansa Akademik: Jurnal Pembangunan Masyarakat Vol. 9 No. 2 (2024)
Publisher : Lembaga Dakwah dan Pembangunan Masyarakat Universitas Cokroaminoto Yogyakarta (LDPM UCY)

Show Abstract | Download Original | Original Source | Check in Google Scholar

Many farmers Banjarwaru complain that goat growth is less than optimal, and low productivity. Based on these problems, this community service program aims to ensure that farmers understand and are able to manage goat farms according to standards independently. The method used in this community service program is to look at achievement indicators from socialization activities and cage management training and animal health recording. Based on the achievement indicators from this activity, it shows that 100% of the 20 breeders understand livestock management, housing, and the correct way to record livestock health. A total of 15 people have been able to use maintenance tools and techniques for handling diseases infected by livestock. Based on the results of the achievement indicators obtained from this service activity, it was concluded that breeders in Banjarwaru Village knew and understood the correct way to raise goats and were able to carry out maintenance activities according to good standards.

Analisa Pengukuran Ketebalan Steel Block, Aluminium Block dan Steel Plate Menggunakan Ultrasonic Thickness Gauge Ulikaryani, Ulikaryani; Unggul Satria Jati; Radhi Ariawan; Dian Prabowo; Sabtun Ismi Khasanah; Hamid Abdillah
Infotekmesin Vol 16 No 1 (2025): Infotekmesin: Januari 2025
Publisher : P3M Politeknik Negeri Cilacap

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.35970/infotekmesin.v16i1.2583

Thickness measurement using an ultrasonic sensor is a type of non-destructive test (NDT) that is commonly used in various industries. Measurement of thickness (thickness) on steel blocks, aluminum blocks and steel plates using an ultrasonic thickness gauge. The method used is the contact testing method which is then compared with manual measurements. Based on data analysis from the measurement results, it was found that the thickness with the highest percent error was in the Steel S3 sample, namely 93.87%. Meanwhile, the thickness measurement with the lowest percent error in the Steel plate sample was 0%. Meanwhile, for measuring the dimensions of artificial corrosion defects, the smallest error percentage obtained was 0% for several dimensions, with the average measurement error obtained being 22.82%. The profile shape of the detected artificial corrosion defects is exactly the same as the reference profile. So, measuring the thickness of steel blocks, aluminum blocks and steel plates as well as measuring artificial corrosion defects located in steel plates can be detected well and the measuring results can be trusted.

Optimalisasi Persentase Berat Ekstrak Kulit Buah Nipah sebagai Green Corrosion Inhibitor dengan Variasi Suhu dan Lama Paparan Ulikaryani, Ulikaryani; Jati, Unggul Satria; Triwuri, Nurlinda Ayu
Jurnal Rekayasa Mesin Vol. 18 No. 3 (2023): Volume 18, Nomor 3, Desember 2023
Publisher : Mechanical Engineering Department - Semarang State Polytechnic

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.32497/jrm.v18i3.5063

Penelitian sebelumnya telah diketahui bahwa ekstrak limbah kulit buah nipah (Nypa Fruticans Wurmb) memiliki potensi sebagai penghambat laju korosi pada logam. Oleh karena itu, penelitian ini dilakukan untuk mengetahui persentase berat ekstrak yang optimal sebagai green corrosion inhibitor dalam menghambat laju korosi pada baja karbon ASTM A36 melalui metode weight loss dan uji polarisasi potensiodinamik. Daya hambat korosi baja karbon ASTM A36 menggunakan ekstrak kulit buah nipah ditentukan pada berbagai persen berat ekstrak pada inhibitor terhadap variasi suhu dan lama paparan dengan media korosifnya. Efisiensi inhibisi meningkat dengan meningkatnya persen berat ekstraknya. Efisiensi inhibisi tertinggi berdasarkan uji weight loss sebesar 97,87% dengan laju korosi 0,00002 mpy yang diperoleh pada persentase ekstrak 15% dengan lama paparan 4 hari. Sedangkan, berdasarkan uji polarisasi potensiodinamik diperoleh laju korosi terendah terdapat pada sampel dengan persentase ekstrak 12%b/v inhibitor sebesar 1,6747 mmpy dengan efisiensi inhibisi sebesar 76,13% pada suhu 30oC. Berdasarkan hasil uji dapat pula disimpulkan bahwa semakin tinggi suhu paparan maka akan semakin meningkatkan laju korosi. Sedangkan, lama waktu paparan tidak selalu meningkatkan laju korosi pada sampel dengan inhibitor. Hal ini dimungkinkan dipengaruhi oleh efek jenuh dari adsorpsi inhibitor terhadap logam itu sendiri. Sedangkan pada sampel tanpa inhibitor selalu menunjukkan peningkatan laju korosi seiring dengan bertambahnya lama waktu paparan

Karakteristik Struktur Kristal In2Se3 Hasil Preparasi Dengan Metode Bridgman Ulikaryani, Ulikaryani; Sodikin, Jenal; Akhlis Sarihidaya Laksana, Nur; Satria Jati, Unggul; Kristiningsih, Ari
Infotekmesin Vol 14 No 1 (2023): Infotekmesin: Januari, 2023
Publisher : P3M Politeknik Negeri Cilacap

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.35970/infotekmesin.v14i1.1753

Apart from using silicon material, thin-layer solar cells can be made from various types of semiconductor materials, such as a combination of groups III and VI. In solar cell applications, these materials are usually used as n-type coatings. This study not only aimed to determine the crystal structure and the effect of annealing temperature on the crystal lattice parameters but also to determine the chemical composition and surface morphological structure of the crystals formed from the preparation. The crystal growth process was carried out using the Bridgman method with different heating patterns. The temperature in both annealing temperatures is 200oC and 250oC. The physical properties of the prepared In2Se3 crystals were characterized using XRD, SEM, and EDAX. XRD Characterization was used to determine the crystal structure, while SEM and EDAX characterization was used to determine the surface morphology and chemical composition of the crystals. The result of the XRD characterization showed that the formed In2Se3 crystals were polycrystals with a hexagonal structure. Based on the diffractogram obtained, the In2Se3 crystalline heating 1 has better quality. EDAX analysis showed that the In2Se3 crystals were composed of elements of In and Se with a mole ratio of 2:9, while the SEM characterization showed that the color of the surface morphology of the In2Se3 crystals was not homogeneous.

Simulasi Tegangan (Stress) Pada Komponen Rangka Mesin Uji Tarik Sealent Menggunakan Solidworks Prabowo, Dian; Satria Jati, Unggul; Ulikaryani, Ulikaryani; Hardini, Probo
Infotekmesin Vol 14 No 2 (2023): Infotekmesin: Juli, 2023
Publisher : P3M Politeknik Negeri Cilacap

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.35970/infotekmesin.v14i2.1947

A series of processes are carried out in order to obtain the desired product result. One of the processes carried out is testing the strength of polymers by means of tensile testing in this case testing of polymer-based sealants. The method used is the method of simulating frame loading on the tensile testing machine that has been made. The software used to assist the simulation process is SolidWorks. The simulation is carried out in static mode or a fixed loading (no movement or vibration). A stress Analysis Simulation is carried out to get the result of static loading in the form of Ïƒ (stress). Loading simulations on the frame of the tensile testing machine for the tensile testing of the sealant are carried out on the components of the frame with different loading variations. Frame components with upward loading are given an average load of 38.5 MPa. Meanwhile, the frame components with downward loading are given an average load of 6.169 MPa. The largest average stress obtained from each component is 0.326 N/mm2. this value does not exceed the yield strength of 235 N/mm2.

Pengaruh Jenis Limbah Aluminium Pada Proses Pengecoran Menggunakan Tungku Krusibel Terhadap Nilai Kekerasannya Dwi Putra, David; Haqqoni, Faisal; Nurhilal, Mohammad; Ulikaryani, Ulikaryani
Infotekmesin Vol 14 No 2 (2023): Infotekmesin: Juli, 2023
Publisher : P3M Politeknik Negeri Cilacap

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.35970/infotekmesin.v14i2.1948

Aluminum waste that has accumulated due to the widespread use of aluminum in household needs, daily life, and in the manufacture of industrial material components will have an impact on the environment if not handled properly. It is necessary to utilize aluminum waste in a product that has a sale value through a casting process using a crucible furnace. This research was conducted to determine the hardness differences of waste aluminum from used aluminum cans, used aluminum pots, and used aluminum wires melted in a smelting furnace. This study uses quantitative analysis and experimental research types. Tests carried out on this crucible furnace were carried out to determine the effect of the type of aluminum waste and the length of time it took to smelt the three types of material on the hardness results. The results of the Rockwell hardness test on aluminum can waste have an average value of 71.38 HRB, on aluminum pans waste it has an average value of 71.68 HRB, and on aluminum cable waste it has an average value of 53.02 HRB.

Analisa Pengukuran Ketebalan Steel Block, Aluminium Block dan Steel Plate Menggunakan Ultrasonic Thickness Gauge Ulikaryani, Ulikaryani; Unggul Satria Jati; Radhi Ariawan; Dian Prabowo; Sabtun Ismi Khasanah; Hamid Abdillah
Infotekmesin Vol 16 No 1 (2025): Infotekmesin: Januari 2025
Publisher : P3M Politeknik Negeri Cilacap

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.35970/infotekmesin.v16i1.2583

Thickness measurement using an ultrasonic sensor is a type of non-destructive test (NDT) that is commonly used in various industries. Measurement of thickness (thickness) on steel blocks, aluminum blocks and steel plates using an ultrasonic thickness gauge. The method used is the contact testing method which is then compared with manual measurements. Based on data analysis from the measurement results, it was found that the thickness with the highest percent error was in the Steel S3 sample, namely 93.87%. Meanwhile, the thickness measurement with the lowest percent error in the Steel plate sample was 0%. Meanwhile, for measuring the dimensions of artificial corrosion defects, the smallest error percentage obtained was 0% for several dimensions, with the average measurement error obtained being 22.82%. The profile shape of the detected artificial corrosion defects is exactly the same as the reference profile. So, measuring the thickness of steel blocks, aluminum blocks and steel plates as well as measuring artificial corrosion defects located in steel plates can be detected well and the measuring results can be trusted.

Title

Found 19 Documents
Search

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Title Search

Found 19 Documents Search

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Title

Found 19 Documents
Search