Claim Missing Document
Check
Articles

Found 20 Documents
Search

EDUKASI FINTECH LENDING SEBAGAI SOLUSI PERMODALAN UMKM DI MASA PANDEMI COVID-19 DI KECAMATAN WAJAK MALANG Pratama, M. Mirza Abdillah; Azizah, Ziadatul; Muntarwikhi, Soimun; W., Ovita Dewi Sandra; Dilasari, Ayuerma; Nurmawati, Kikiy Mega; Rahayu, Norma Anis; Dewi, Prahasti Tri Tungga
Jurnal Graha Pengabdian Vol 2, No 3 (2020)
Publisher : Lembaga Penelitian dan Pengabdian Masyarakat (LP2M) Universitas Negeri Malang

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

Salah satu dampak dari adanya pandemi COVID-19 adalah menurunnya pertumbuhan perekonomian Indonesia yang hanya mencapai angka 2,97% pada triwulan 1-2020. Protokol kesehatan seperti social distancing, physical distancing, lockdown, dan pembatasan sosial berskala besar (PSBB) berimbas pada penurunan pendapatan warga, termasuk warga Desa Wonoayu yang masih bergantung pada hasil pertanian dan peternakan. Dalam rangka membantu membangkitkan perekonomian warga, tim pengabdian mengadakan sosialisasi pengenalan fintech lending bagi usaha mikro, kecil, dan menengah (UMKM) dengan tujuan mengenalkan kepada masyarakat mengenai pentingnya permodalan dalam usaha, mengenalkan teknologi fintech lending sebagai solusi permodalan bagi UMKM, memberi pemahaman perbedaan peminjaman di bank, koperasi dan fintech lending serta antisipasi penipuan yang saat ini sedang marak terjadi. Metode yang kami gunakan berupa semi-webinar dengan penayangan video penjelasan dari pemateri dan sesi tanya jawab melalui telepon. Hasil dari kegiatan ini menunjukkan bahwa fintech lending merupakan pengetahuan baru bagi sebagian besar warga Desa Wonoayu. Pemahaman warga mengenai pentingnya permodalan dalam usaha, fintech lending, serta UMKM juga meningkat secara signifikan setelah mengikuti kegiatan ini. Fintech lending dapat dijadikan solusi permodalan usaha untuk menghidupkan perekonomian warga pasca pandemi melihat tingginya minat warga dalam membangun usaha.
Analisis Biaya Konstruksi Balok Beton Gradasi dengan Penggunaan Tulangan Maksimum M. Mirza Abdillah Pratama
Borneo Engineering : Jurnal Teknik Sipil Volume 5 Nomor 2 Tahun 2021
Publisher : Jurusan Teknik Sipil, Fakultas Teknik, Universitas Borneo Tarakan

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.35334/be.v5i2.1961

Abstract

Desain tulangan maksimum merupakan konsep desain yang harus dihindari karena risiko terhadap kegagalan getas. Namun demikian, perencana struktur kerap kali mendapati batasan desain untuk merancang elemen dengan dimensi minimalis sehingga penggunaan rasio tulangan maksimum menjadi tidak terhindarkan. Hal tersebut masih diperkenankan dengan tetap memperhatikan nilai regangan tulangan tarik agar melampaui titik lelehnya ketika mengalami kegagalan. Pada penelitian ini, penulis bermaksud untuk menganalisis lebih lanjut terkait analisis biaya terhadap kinerja yang dihasilkan dari balok beton gradasi dengan penggunaan tulangan maksimum. Balok didesain dengan ukuran 1720 x 130 x 260 mm dan 1400 x 130 x 195 mm, dan diuji lentur dengan metode four point bending. Hasil penelitian menunjukkan bahwa 1) Dengan rasio dimensi 2/3, penambahan biaya konstruksi sebesar 3.69% akan meningkatkan kinerja balok sebesar 3.57% apabila pembesiannya didesain terhadap mutu beton terendahnya; 2) Penerapan gradasi mutu dapat menurunkan biaya pekerjaan hingga 25.32% dengan kompensasi kinerja sebesar 33.91% pada balok dengan rasio dimensi 1/2 yang pembesiannya didesain terhadap mutu beton tertingginya; 3) Balok gradasi dapat mengoptimasi biaya pekerjaan tanpa mengkompensasi kinerja struktur secara signifikan khususnya pada penggunaan tulangan maksimum.
Peningkatan Keterampilan Pembuatan Olahan Minuman Berbahan Dasar Jahe sebagai Usaha Menguntungkan pada Kelompok PKK Kecamatan Wajak M. Mirza Abdillah Pratama; Anggini Fitria Astutik; Rizki Susilowati; Pixel Joshua Syebat Aprilido; Ahmad Difa Aflah; Kikiy Mega Nurmawati; Norma Anis Rahayu; Prahasti Tri Tungga Dewi
Jurnal KARINOV Vol 3, No 3 (2020): September
Publisher : Institute for Research and Community Service (LP2M), Universitas Negeri Malang

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17977/um045v3i3p181-188

Abstract

Wonoayu merupakan Desa pembudidaya jahe dalam jumlah yang cukup  banyak, selama ini hasil budidaya dijual dalam bentuk mentah, beberapa di antaranya terbiasa mengolah jahe sebagai bubuk jahe instan dan kripik jahe,  belum variasnya produk olahan berbahan jahe ini menyebabkan nilai ekonomi jahe relative rendah. Kegiatan Pengabdian kepada masyarakat ini bertujuan untuk meningkatkan keterampilan masyarkat dalam mengolah jahe menjadi berbagai variasi produk, juga menyadarkan masyarkat akan peluang berwirausaha dari sector ini. Kelompok sasaran kegiatan adalah ibu-ibu yang tergabung dalam organisasi Pembinaan Kesejahteraan Keluarga (PKK). Tingkat keberhasilan kegiatan diukur dari tingkat ketertarikan dan partisipasi serta mutu produk akhir. Metode yang digunakan adalah tahapan analisis kebutuhan, sosialisasi dan pelatihan berbantuan video pembelajran. Hasil kegiatan menunjukkan antusiasme peserta selama kegiatan pembuatan  produk sangat baik,  produk yang telah dihasilkan dan siap diproduksi untuk dipasarkan adalah ragam sirup dari bahan jahe, diantarnya adalah  minuman JEMON (Jahe Madu Lemon). Kata kunci— jahe lemon, , sirup jahe, wirausaha PKK Abstract Wonoayu is a village of ginger cultivators in large quantities, so far the cultivation products are sold in raw form, some of them are accustomed to processing ginger as instant ginger powder and ginger chips, the lack of variety in processed products made from ginger causes the economic value of ginger to be relatively low. This community service activity aims to improve community skills in processing ginger into various product variations, as well as making people aware of entrepreneurial opportunities in this sector. The target group for the activity are mothers who are members of the Family Welfare Development Organization (PKK). The level of success of the activity is measured by the level of interest and participation and the quality of the final product. The method used is the stage of needs analysis, socialization and training assisted by learning videos. The results of the activity showed that the enthusiasm of the participants during the product-making activities was very good. The products that have been produced and are ready to be produced for market are a variety of syrups made from ginger, including JEMON (Ginger Honey Lemon). Keywords— lemon ginger, ginger syrup, PKK entrepreneurship
Evaluasi Kinerja Struktur Gedung Bertingkat Menggunakan Pendekatan Desain Berbasis Kinerja (Studi Kasus: Gedung Pendidikan Rangka Beton Bertulang 7 Lantai) Saifulloh Fatah Pangestu; M Mirza Abdillah Pratama
Cantilever: Jurnal Penelitian dan Kajian Bidang Teknik Sipil Vol 10 No 2 (2021): Cantilever
Publisher : Department of Civil Engineering and Planning, Faculty of Engineering, Sriwijaya University

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (2579.103 KB) | DOI: 10.35139/cantilever.v10i2.110

Abstract

In Indonesia, earthquake-resistant structures are governed by SNI as design codes, which are updated on a regular basis. As a result, existing buildings with outdated requirements must be reviewed so that the building's performance may be assessed in light of the most recent codes. Pushover analysis and direct displacement-based design are used to characterize the real condition of the building in order to assess its performance. The 7-story reinforced concrete building structure in this study was designed according to SNI 03-2847-2002 and SNI-1726-2002. This structure will be evaluated utilizing the FEMA 440 and FEMA 356 procedures, as well as SNI 1726:2019. The results show that the structure meets the minimal performance limit criteria (which is life safety) in terms of displacement and drift values from the pushover analysis, based on FEMA 356 and FEMA 440 performance levels. The evaluation indicates better structural response parameter values (R, Ω0, and Cd) than that of SNI 1726:2019, indicating that the building performance is good and capable of withstanding the design earthquake load.
STUDI EKSPERIMENTAL PENGARUH TEGANGAN TEKAN SELAMA PROSES PRODUKSI TERHADAP KUAT TEKAN DRY CONCRETE M. Mirza Abdillah Pratama; Vemi Widoanindyawati; Han Ay Lie; Purwanto Purwanto
Jurnal Karya Teknik Sipil Volume 3, Nomor 4, Tahun 2014
Publisher : Departemen Teknik Sipil, Fakultas Teknik Universitas Diponegoro

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (452.617 KB)

Abstract

Dry concrete is basically a cementitious material, consisting of aggregates imbedded in a cement matrix that function as the binding agent. The water cement factor during this production is customary kept low, since from the economic point of view, speed in production is favored. A low water-cement-factor will result in a faster unmolding of elements. As a consequence, the probability of the hydration process is not at optimum. A technique of optimizing the hydration process is to apply a compression stress to the dry concretes, during the hydration stage. This stress is aimed to reduce the air voids in the mixture and to enable the entrapped water within the mortar to optimize the reaction with the cement. The application of compression stress is not only freed the entrapped water, but also creates a more dense material so it will provides a better performance of the dry concrete. This study uses 2 types of mix design with a water-cement ratio of 0.4 and 9 types of compressive stress variations during the production process from 0 MPa to 40 MPa. The experimental test showed that the compressive stress during the production process affect the compressive strength of dry concrete. The greater compressive stress given during the production process increase the compressive strength of the dry concrete. This increase occurred gradually until it reaches the optimum compressive stress, which is 35 MPa. The rate of increase in compressive strength and the optimum compressive stress on both the mix design is in the same point, it is due to both the mix design using the same water-cement ratio.
STUDI EKSPERIMENTAL PENGARUH TEGANGAN TEKAN SELAMA PROSES PRODUKSI TERHADAP KUAT TEKAN DRY CONCRETE M. Mirza Abdillah Pratama; Vemi Widoanindyawati; Han Ay Lie; Purwanto Purwanto
Jurnal Karya Teknik Sipil Volume 3, Nomor 4, Tahun 2014
Publisher : Departemen Teknik Sipil, Fakultas Teknik Universitas Diponegoro

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (452.617 KB)

Abstract

Dry concrete is basically a cementitious material, consisting of aggregates imbedded in a cement matrix that function as the binding agent. The water cement factor during this production is customary kept low, since from the economic point of view, speed in production is favored. A low water-cement-factor will result in a faster unmolding of elements. As a consequence, the probability of the hydration process is not at optimum. A technique of optimizing the hydration process is to apply a compression stress to the dry concretes, during the hydration stage. This stress is aimed to reduce the air voids in the mixture and to enable the entrapped water within the mortar to optimize the reaction with the cement. The application of compression stress is not only freed the entrapped water, but also creates a more dense material so it will provides a better performance of the dry concrete. This study uses 2 types of mix design with a water-cement ratio of 0.4 and 9 types of compressive stress variations during the production process from 0 MPa to 40 MPa. The experimental test showed that the compressive stress during the production process affect the compressive strength of dry concrete. The greater compressive stress given during the production process increase the compressive strength of the dry concrete. This increase occurred gradually until it reaches the optimum compressive stress, which is 35 MPa. The rate of increase in compressive strength and the optimum compressive stress on both the mix design is in the same point, it is due to both the mix design using the same water-cement ratio.
MOMENT-CURVATURE ANALYSIS OF GRADED CONCRETE BEAM WITH CONCRETE STRENGTH DISPARITY VARIATIONS M. Mirza Abdillah Pratama; Moch. Febrian Andi; Christian Hadhinata
Jurnal Pensil : Pendidikan Teknik Sipil Vol. 11 No. 1 (2022): Jurnal Pensil : Pendidikan Teknik Sipil
Publisher : LPPM Universitas Negeri Jakarta

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (779.35 KB) | DOI: 10.21009/jpensil.v11i1.25072

Abstract

The application of graded concrete on structural elements is predicted to increase the capacity of the structural performance, serviceability, and to reduce costs compared to conventional concrete structures. This study aims to analyze (1) the load-deflection relationship, (2) the moment-curvature, (3) the deflection ductility ratio, and (4) the crack pattern. This study used reinforced concrete (RC) beams specimens with the dimension of 13x19x150 cm which was categorized as reference specimens and graded concrete beams. For reference specimens, an RC beam possessing concrete strength of 30 MPa; 40 MPa; 50 MPa were prepared; For the graded concrete beams, two specimens made of 30-40 MPa; 30-50 MPa; 40-50 MPa were prepared. In terms of casting graded concrete beams, low-strength concrete is placed on the tensile fiber of the beam, while on the compressive fiber of the beam, high-strength concrete is placed. The specimens were tested using the four-point bending method. The results showed that the increase in the concrete strength in the compression fiber of the beam contributed to the increase in load capacity, stiffness, and serviceability in the post-crack phase. The increase of concrete strength in compression fibers by 20 MPa is considered effective and has a positive impact on the moment-curvature capacity and is considered efficient in construction costs. The deflection ductility of the beam is classified as partial ductile and is adequate for structural design in earthquake-prone areas. A flexural cracks pattern was found on each specimen.
Analisis Kinerja Bangunan Gedung Tinggi Dengan Penambahan Dinding Geser (Studi Kasus: Bangunan 8 Lantai) M Mirza Abdillah Pratama; Septiana Dyah Sugmana Putri; Edi Santoso
Siklus : Jurnal Teknik Sipil Vol. 7 No. 2 (2021)
Publisher : Program Studi Teknik Sipil Fakultas Teknik Universitas Lancang Kuning

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.31849/siklus.v7i2.6922

Abstract

Shear walls in high-rise buildings serve to increase the resistance of high-rise buildings to lateral loads. This study aims to compare the structural performance of an existing 8 (eight) storey building designed as a special moment resisting frame structure against a building designed as a dual system, which consists of: structural vibration time, base shear force, displacement, and drift. Three configurations for shear walls are designed, as follows: (1) L-shaped located at the corner of one side of the building, totaling 2 (two) units (SW1); (2) L-shaped located at the four corners of the building totaling 4 (four) units (SW2); and 3) I-shaped located along the side of the building totaling 6 (six) units (SW3). Simulations are run using the Etabs by taking into account dead loads, live loads, and earthquake loads. The results show that the addition of shear walls can: (1) reduce the vibration period of the structure up to 62,55% in SW3, (2) increase the base shear force up to 86,34% in SW3, (3) reduce peak displacement up to 84,86% in SW3, and (4) reduce the drift between floors up to 89,58% in SW3. However, the SW2 is considered to be better applied to the building by taking into account the structural performance, effectiveness and efficiency factors.
PENINGKATAN PENGETAHUAN SANITASI MASYARAKAT KAMPUNG TRIDI KOTA MALANG MELALUI SOSIALISASI SEPTIC TANK UNTUK PEMUKIMAN PADAT PENDUDUK Anie Yulistyorini; M.Mirza Abdillah Pratama; M.Musthofa Al Ansyorie; Gilang Idfi; Roro Roro
Aptekmas Jurnal Pengabdian pada Masyarakat Vol 3 No 2 (2020): APTEKMAS Volume 3 Nomor 2 2020
Publisher : Politeknik Negeri Sriwijaya

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (539.304 KB) | DOI: 10.36257/apts.v3i2.2060

Abstract

Kampong Tridi has become one of referable tourism destinations in Malang city. Instead of being renowned among locals, the kampong still has several issues to struggle regarding environmental management, specifically communal wastewater treatment. Septic tank as blackwater treatment system is not installed in residence majority which is about 63% of total number. This circumstance makes them directly dispose waste into Brantas River. The purpose of this socialization is to make the community aware of the importance of treating wastewater before disposal including steps to keep living environment. T test result showed the effect of socialization to the community’s environmental awareness through pretest and posttest comparison (p = 0.0004). To recapitulate, we conclude that this socialization brings significant positive impact to local’s environmental preservation awareness.
IMPLEMENTASI TREASURE BINGO UNTUK MENINGKATKAN 4C (CRITICAL, CREATIVE, COLLABORATIVE, AND COMMUNICATIVE THINKING SKILL ) PESERTA DIDIK SDN WONOAYU KABUPATEN MALANG Selviska Pangestu; M. MIRZA ABDILLAH PRATAMA
Jurnal Pasopati : Pengabdian Masyarakat dan Inovasi Pengembangan Teknologi Vol 4, No 2 (2022)
Publisher : Fakultas Teknik Universitas Diponegoro

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

Peserta didik dituntut untuk dapat memiliki berbagai kemampuan, di antaranya kemampuan berpikir kritis, kreatif, kolaboratif, komunikatif dan cakap dalam menyelesaikan permasalahan. Tenaga pendidik di SDN Wonoayu masih menggunakan cara konvensional dengan berbagai kendala salah satunya minimnya jaringan internet yang dapat menghambat berkembangnya pendidikan di SDN Wonoayu. Sebagai solusi untuk mengatasi masalah tersebut dibutuhkan suatu model serta media pendidikan yang dapat memberikan kontribusi terhadap kemampuan 4C, namun juga interaktif salah satunya melalui permainan matematika yaitu Treasure Bingo. Kegiatan ini memiliki tujuan untuk meningkatkan kemampuan 4C (critical, creative, collaborative and communicative thinking skill) peserta didik SDN Wonoayu. Tahapan dari kegiatan pengabdian ini diawali dengan analisis kebutuhan yang dilaksanakan dengan menyebar kuesioner dan juga survey lapangan serta observasi langsung ke SDN Wonoayu. Kemudian dilanjutkan dengan persiapan media dan kebutuhan lain yang diperlukan saat pelaksanaan kegiatan. Setelah itu dilanjutkan dengan kegiatan pembelajaran menggunakan media Treasure Bingo dan yang terakhir adalah evaluasi. Dijumpai adanya perbedaan yang cukup signifikan terkait dengan motivasi belajar dan kemampuan 4C peserta didik saat sebelum dan pasca kegiatan. Hasil kegiatan menunjukkan bahwa motivasi belajar peserta didik mengalami peningkatan hal tersebut ditunjukkan saat pembelajaran menggunakan media Treasure Bingo peserta didik sangat bersemangat dan antusias serta permainan Treasure Bingo ini dapat meningkatkan kemampuan 4C peserta didik SDN Wonoayu.Kata kunci : permainan matematika, Treasure Bingo, 4C, SDN Wonoayu