Claim Missing Document
Check
Articles

Found 3 Documents
Search
Journal : Quantum Teknika

Analisis Konsistensi Volume Output Pada Nozzle Barrel Mesin Mini Injeksi V-Line Menggunakan Material Plastik Polypropylene ExxonMobil AP03B Bayu Prabandono; Alex Satria Wibawa; Mirza Yusuf; Agus Kurniawan; Aditya Nugraha
Quantum Teknika : Jurnal Teknik Mesin Terapan Vol 5, No 2 (2024): April
Publisher : Universitas Muhammadiyah Yogyakarta

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.18196/jqt.v5i2.21837

Abstract

One of the processes commonly used in making plastic goods is the injection molding process. Every process in injection molding has a very important role. A less-than-perfect process will result in defects or failure in the product. To reduce product defects, one of the processes that must be researched is the barrel purging process. The purging volume on the mini injection machine using the V-line method is inconsistent, as evidenced by the fact that if the purging waste, or what is usually called an avalanche is weighed, it will produce a non-uniform mass. This research uses a mini injection machine with the V-line method which has 2 main steps to carry out the plastic injection process; dosing and injecting. Unlike injection engines in general, this engine does not have a check-ring to withstand back pressure. This machine uses a shut-off system as a replacement for the check-ring role. This machine has never been subjected to a purging volume consistency testing process. The consistency of the purging volume greatly influences the product uniformity results. The research method used in this final assignment is direct. Data collection and test specimen collection will be taken directly on the mini injection machine using the V-line method. The steps taken in this research are planning, taking data, taking test specimens, processing test specimen data, and comparing test specimen data to obtain analysis results. The research results show that the mini V-line injection machine cannot support mass production, because increasing the screw rotation speed will affect the consistency of the volume of plastic that will be produced in the barrel, causing production to not run quickly and precisely.
Analisis Kekuatan pada Pengembangan Desain Shelf pada Base Cabinet dengan Analisis Elemen Hingga menggunakan Perangkat Lunak Solidworks CAE Bayu Prabandono; Rafael Bhima Sena Purnama Putra; Andronikus Cahya Pradana; Agus Kurniawan; Aditya Nugraha; Mirza Yusuf
Quantum Teknika : Jurnal Teknik Mesin Terapan Vol. 6 No. 1 (2024): October
Publisher : Universitas Muhammadiyah Yogyakarta

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.18196/jqt.v6i1.19979

Abstract

ATMI Duta Engineering company is a manufacturing company engaged in the field of sheet metal with a material cutting process using laser cutting technology. Sheet metal products produced at ATMI Duta Engineering company is very diverse, one of which is the base cabinet. The base cabinet has main components, one of which is the shelf. Based on the data obtained from the interview process, there are problems, namely the shelf has never been analyzed, there are no finished products, and there is a risk of damage due to excessive loading. The solution to the shelf problem is to carry out a shelf design analysis using the finite element analysis method through Solidworks CAE software. The CAE simulation was applied to 27 variations of the shelf design by combining 3 test variables, namely the shelf model, the reinforcement model, and the thickness of the material. The material used in the simulation is SPCC material with a thickness of 1mm, 1.2mm and 1.5mm. The CAE simulation results obtained are then compared with reference to the SEFA 8M-2016 standard. The loading given in the CAE simulation is ± 108 kg (1.2 SEFA standards). The strongest variation obtained from the elimination process is variation 19 with a combination of shelf model 1 design, reinforcement model A, and with a material thickness of 1.5mm. Variation 19 meets the SEFA 8M-2016 standard because the displacement value is 1.065mm and this value is smaller than 6.35mm.
Analisis Konsistensi Volume Output Pada Nozzle Barrel Mesin Mini Injeksi V-Line Menggunakan Material Plastik Polypropylene ExxonMobil AP03B Bayu Prabandono; Alex Satria Wibawa; Mirza Yusuf; Agus Kurniawan; Aditya Nugraha
Quantum Teknika : Jurnal Teknik Mesin Terapan Vol. 5 No. 2 (2024): April
Publisher : Universitas Muhammadiyah Yogyakarta

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.18196/jqt.v5i2.21837

Abstract

One of the processes commonly used in making plastic goods is the injection molding process. Every process in injection molding has a very important role. A less-than-perfect process will result in defects or failure in the product. To reduce product defects, one of the processes that must be researched is the barrel purging process. The purging volume on the mini injection machine using the V-line method is inconsistent, as evidenced by the fact that if the purging waste, or what is usually called an avalanche is weighed, it will produce a non-uniform mass. This research uses a mini injection machine with the V-line method which has 2 main steps to carry out the plastic injection process; dosing and injecting. Unlike injection engines in general, this engine does not have a check-ring to withstand back pressure. This machine uses a shut-off system as a replacement for the check-ring role. This machine has never been subjected to a purging volume consistency testing process. The consistency of the purging volume greatly influences the product uniformity results. The research method used in this final assignment is direct. Data collection and test specimen collection will be taken directly on the mini injection machine using the V-line method. The steps taken in this research are planning, taking data, taking test specimens, processing test specimen data, and comparing test specimen data to obtain analysis results. The research results show that the mini V-line injection machine cannot support mass production, because increasing the screw rotation speed will affect the consistency of the volume of plastic that will be produced in the barrel, causing production to not run quickly and precisely.