Garuda - Garba Rujukan Digital

Article Per Year (5 Year)

All

Indonesian Journal of Chemistry

ijc
Website

Published by Universitas Gadjah Mada

ISSN : 14119420 EISSN : 24601578 DOI : -

Core Subject : Science, Engineering,

Chemical Engineering, Chemistry & Bioengineering Chemistry

Indonesian Journal of Chemistry is an International, peer-reviewed, open access journal that publishes original research articles, review articles, as well as short communication in all areas of chemistry including applied chemistry. The journal is accredited by The Ministry of Research, Technology and Higher Education (RISTEKDIKTI) No : 21/E/KPT/2018 (in First Rank) and indexed in Scopus since 2012. Since 2018 (Volume 18), Indonesian Journal of Chemistry publish four issues (numbers) annually (February, May, August and November).

Arjuna Subject : -

Articles 1,981 Documents

87 88 89 90 91

A Fixed-Bed Column Study for Removal of Organic Dyes from Aqueous Solution by Pre-Treated Durian Peel Waste Nguyen Thi Thuong; Nguyen Thi Tuyet Nhi; Vo Thi Cam Nhung; Hoang Ngoc Bich; Bui Thi Phuong Quynh; Long Giang Bach; Nguyen Duy Trinh
Indonesian Journal of Chemistry Vol 19, No 2 (2019)
Publisher : Universitas Gadjah Mada

A number of harmful effects on the ecosystem, the life of humankind, and living species caused by dye-contaminated wastewater have urged the development for an efficient and cost-efficient treatment method for colored effluents. The cellulose-based adsorbents have been considered as a facile and efficient approach to remove hazardous pollutants because of the abundance of inexpensive agricultural wastes in Viet Nam. This study aims to investigate the elimination of methylene blue (MB) and crystal violet (VL) from wastewater using a fixed-bed column of pre-treated durian peel. Examined variables in the process are bed depths (2–6 cm), flow rate (5–20 mL/min), and influent dye concentrations (200–600 mg/L). The highest adsorption amount of pre-treated DP was 235.80 mg/g and 527.64 mg/g, respectively, on a 600 mg/L of methylene blue and crystal violet achieved within a bed height of 4 cm and a flow rate of 10 mL/min. Accordingly, the breakthrough curves were constructed and modeled using the relevant theoretical models under the effects of different experimental conditions. Pre-treated durian peel was found to exhibit high adsorption capacity for cationic dye in an initial concentration of 200–600 mg/L with complete removal being obtained.

Synergistic Effect of Two Type Cellulase Immobilized on Chitosan Microparticle as Biocatalyst for Coconut Husk Hydrolysis Afan Hamzah; Lidya Lorenta Sitompul; Irma Nurhanifah Fenda Putri; Soeprijanto Soeprijanto; Arief Widjaja
Indonesian Journal of Chemistry Vol 19, No 2 (2019)
Publisher : Universitas Gadjah Mada

The effectivity of employing two types of cellulases from Aspergillus niger and Trichoderma resei covalently immobilized on chitosan microparticle was investigated. Reducing sugar from CMC yielded by immobilized cellulase from T. resei alone and A. niger alone was 0.316 g/L and 0.244 g/L, respectively. Simultaneous use of both cellulases shows a significant increase of reducing sugar produced to 1.020 g/L. The effective combination of this two types of cellulases also occurred when coconut husk was used as substrate. A very high enzyme coupling of 92.06% compared to free enzyme was obtained in the immobilization. Addition of GDA not only increased enzyme coupling to 100% but also improved sugar produced. Immobilized cellulase was successfully maintained its activity until 5 cycles

Comparative Evaluation of Protease Extraction from Leaves of Syzygium polyanthum Noorhafiza Yahya; Zatul Iffah Mohd Arshad; Siti Kholijah Abdul Mudalip; Siti Zubaidah Sulaiman; Rohaida Che Man; Shalyda Md Shaarani; Mohd Hairul Ab. Rahim
Indonesian Journal of Chemistry Vol 19, No 2 (2019)
Publisher : Universitas Gadjah Mada

In this study, the comparison of four extraction methods for protease from the leaves of Syzygium polyanthum was evaluated. The methods include sodium phosphate buffer, 1-methyl-8-oxyquinolinium betaine (QB) solvent based extraction, hydrogen-bond acceptor (HBA) solvent based extraction and Trichloroacetic-acetone (TCA) precipitation. The effectiveness of these extraction methods was measured based on the specific activity demonstrated by the crude protease extracted in this experiment. The results indicated that QB solvent-based extraction method could extract the crude protease from the leaves of S. polyanthum with the highest specific activity of 10.204 ± 0.329 U/mg compared to other extraction methods.

Screening of Microwave-Assisted-Batch Extraction Parameters for Recovering Total Phenolic and Flavonoid Contents from Chromolaena odorata Leaves through Two-Level Factorial Design Oluwaseun Ruth Alara; Abdurahman Hamid Nour; Siti Kholijah binti Abdul Mudalip
Indonesian Journal of Chemistry Vol 19, No 2 (2019)
Publisher : Universitas Gadjah Mada

Microwave-assisted extraction (MAE) of phenolic compounds from Chromolaena odorata leaves was investigated using one-factor-at-a-time (OFAT) and two-level factorial design. The MAE parameters studied were irradiation time (A: 1–5 min); microwave power level (B: 400-800 W); extraction temperature (C: 60–80 °C); solvent/feed ratio (D: 8:1–14:1 mL/g); and ethanol concentration (E: 20–60% v/v). The optima yields of TPC and TFC were 56.13 mg GAE/g d.w. and 44.78 mg QE/g d.w., respectively were achieved from MAE of C. odorata leaf at irradiation time of 2 min, microwave power of 600 W, temperature of 60 °C, solvent:feed ratio of 10:1 mL/g, and ethanol concentration of 40% v/v through one-factor-at-time (OFAT) experimental trials. The results obtained from a two-level factorial design experiments reflected that only ethanol concentration (20–60% v/v), irradiation time (1–5 min) and microwave power level (400–800 W) had significant effects on the yields of total phenolic content (TPC) and total flavonoid content (TFC) from C. odorata leaves (p < 0.05). However, temperature and solvent/feed ratio was not significant. In addition, the interactions AB (irradiation time and microwave power) and AE (irradiation time and ethanol concentration) contributed greatly to the recovery yields.

Physicochemical and Microbiological Analysis of Stingless Bees Honey Collected from Local Market in Malaysia Wan Nadja Julika; Azilah Ajit; Ahmad Ziad Sulaiman; Aishath Naila
Indonesian Journal of Chemistry Vol 19, No 2 (2019)
Publisher : Universitas Gadjah Mada

The growing demand for honey in the market has led to the occurrence of the tampering honey with foreign substances and increases the production of artificial honey. Due to this concern, this study works on the physicochemical and microbial characterization of stingless bee honey. The physicochemical analysis showed that the honey possessed pH (2.51–3.26), free acidity (121.1 to 318.7 meq/kg), moisture (19.4–30.9%), electrical conductivity (0.33–0.69 mS/cm), ash content (2.75–4.31 g/100g), Hydroxymethylfurfural (HMF) content (35.4 to 461.7 mg/kg) and diastase activity (2.71 to 6.11 DN). Also, sugar profile of honey showed that the honey contained fructose (15.03–32.52 g/100g), glucose (12.17–34.55 g/100g) and sucrose (0.01–7.29 g/100g). The harvested honey, H1, and H2 have the highest potential to become an antibacterial agent to treat disease compared to commercial honey samples because they were active against Gram-negative bacteria. All analyzed samples were within the maximum limit of the quality criteria set by the Malaysian Kelulut Standard and Codex Alimentarius except for free acidity, HMF, and Diastase Number. All the data obtained is vital in order to create a specific statute for stingless bees honey in Malaysia that may help to protect the consumer from purchasing adulterated honey.

Thermal and Dynamics Mechanical Analysis of Polypropylene Blown Films with Crude Palm Oil as Plasticizer Siti Hasnah Kamarudin; Emiliana Rose Jusoh; Luqman Chuah Abdullah; Mohd Halim Shah Ismail; Min Min Aung; Chantara Thevy Ratnam
Indonesian Journal of Chemistry Vol 19, No 3 (2019)
Publisher : Universitas Gadjah Mada

This research aims to investigate the effect of crude palm oil (CPO) as a plasticizer in polypropylene blown film on thermal and dynamic mechanical properties. Polypropylene (PP) was blended with 1, 3, and 5% of CPO using a twin screw extruder. The extruded samples were blown using the blown thin film technique. The samples were analyzed using dynamic mechanical analysis (DMA), differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). From the dynamic mechanical analysis, the storage modulus and loss modulus for PP presented decreasing pattern about 3–5% due to the action of CPO as plasticizer which introduced free volume and enabled the polyolefins chains to deform more easily. The glass transition temperatures (Tg) of PP were found being shifted to lower temperature from 10 to 1 °C with the increasing CPO content. The fraction of crystallization was determined using DSC. The thermogravimetric analysis (TGA) results showed that the incorporation of CPO as plasticizer showed a small increased effect in the thermal stability for PP. These findings have contributed new knowledge to the additives area and give important implications for designing and manufacturing polymer packaging materials.

Synthesis and Characterization of Molybdenum Phthalocyanine as Target Material for High Specific Activity Molybdenum-99 Production Muhamad Basit Febrian; Duyeh Setiawan; Hilda Hidayati
Indonesian Journal of Chemistry Vol 19, No 3 (2019)
Publisher : Universitas Gadjah Mada

High specific activity is a necessity in the fabrication of 99Mo/99mTc radioisotope generators. Recoil reaction, or the Szilard-Chalmers effect, is a method that could be used as an alternative method for increasing specific activity in radioisotope production in light of tightening regulation of highly enriched uranium (HEU) irradiation. Phthalocyanine compounds are usually used as the target material in recoil reactions for the production of high specific radioisotope activity via the (n,γ) reaction. Molybdenum phthalocyanine (Mo-Pc) could be a promising target material in recoil reactions for producing high specific activity of 99Mo. Mo-Pc was synthesized via solid-state reaction between ammonium heptamolybdate and phthalonitrile in a reflux system at 300 °C for 3 h. This optimum condition was identified after performing several variations of temperature and time of reaction, considering FTIR spectra, the yield of product and melting point of the product. XRD measurement showed that Mo-Pc synthesized at optimum condition was free from MoO2, phthalimide and unreacted molybdenum. Mo-Pc has UV-vis properties of Q-band absorption between 600 and 750 nm when dissolved in tetrahydrofuran, dimethylformamide and trifluoroacetic acid. Splitting at absorption peak in tetrahydrofuran and dimethylformamide solution indicated that protonation had occurred. This split peak did not appear in a trifluoroacetic acid solution. In the preliminary study of irradiation of 1 g Mo-Pc at 3.5x1012 n cm–2 s–1 neutron flux, followed by dissolution in tetrahydrofuran and extraction of Mo-99 into NaOH, we obtained Mo-99 solution with a specific activity of 682.35 mCi/g Mo, this being 254.61 times higher than in the regular MoO3 target.

Three Dimensional Structural Modelling of Lipase Encoding Gene from Soil Bacterium Alcaligenes sp. JG3 Using Automated Protein Homology Analysis Dilin Rahayu Nataningtyas; Tri Joko Raharjo; Endang Astuti
Indonesian Journal of Chemistry Vol 19, No 3 (2019)
Publisher : Universitas Gadjah Mada

Bacterial lipases have significant potential to be used as the biocatalyst for many chemical reactions. In this study, a novel gene encoding lipase was isolated from an Alcaligenes sp. JG3. A pair of designed primer has successfully isolated 1 kb (LipJG3) that shares 98% identity towards lipase from Alcaligenes faecalis during sequence analysis. By using in silico tools, LipJG3 was related to the transporter protein sequences. Three highly conserved regions consisting of EASGSKT, VILLD, and LSGGQQQRVAIA were found. These regions were known as ATP-binding signature at Walker-A and Walker-B motifs and the S signature of ABC transporter family respectively. In addition, the 3-D structure of LipJG3 has been suggested but the role of the catalytic triad residues have been not fully understood.

Microwave Assisted Synthesis and Evaluation of Toxicity and Antioxidant Activity of Pyrazoline Derivatives Jasril Jasril; Hilwan Yuda Teruna; Aisyah Aisyah; Nurlaili Nurlaili; Rudi Hendra
Indonesian Journal of Chemistry Vol 19, No 3 (2019)
Publisher : Universitas Gadjah Mada

Four pyrazoline analogues, 3-(4-methoxyphenyl)-5-naphthalene-1-yl-1-phenyl-4,5-dihydro-pyrazole (3), 3-(4-methoxyphenyl)-5-naphthalene-1-yl-4,5-dihydro-1H-pyrazole (4), 3-(2-methoxyphenyl)-5-naphthalene-1-yl-1-phenyl-4,5-dihydro-pyrazole (5) and 3-(2-methoxyphenyl)-5-naphthalene-1-yl-4,5-dihydro-1H-pyrazole (6) were synthesized via intermolecular cyclization between substituted chalcones and hydrazine derivatives. The compounds were synthesized in two steps. In the first step, the chalcones were synthesized by Claisen-Schmidt reaction. In the second step, they were cyclized with some hydrazine derivatives to form pyrazolines by using glacial acetic acid as a catalyst and assisted by microwave irradiation. The toxicity analysis showed that compound 1 and 2 were toxic with LC50 values of 11.47 and 0.97 μg/mL, respectively. Furthermore, only compound 6 showed high antioxidant activity by using DPPH with an IC50 value of 4.47 μg/mL.

Estimating Factors Determining Emulsification Capability of Surfactant-Like Peptide with Coarse-Grained Molecular Dynamics Simulation Tegar Wijaya; Rukman Hertadi
Indonesian Journal of Chemistry Vol 19, No 3 (2019)
Publisher : Universitas Gadjah Mada

The ability of surfactant-like peptides to emulsify oil has become the main focus of our current study. We predicted the ability of a series of surfactant-like peptides (G6D, A6D, M6D, F6D, L6D, V6D, and I6D) to emulsify decane molecules using coarse-grained molecular dynamics simulations. A 1-μs simulation of each peptide was carried out at 298 K and 1 atm using MARTINI force field. Simulation system was constructed to consist of 100 peptide molecules, 20 decane molecules, water, antifreeze particles and neutralizing ions in a random configuration. Out of seven tested peptides, M6D, F6D, L6D, V6D, and I6D were able to form emulsion while G6D and A6D self-assembled to order b-strands. A higher hydropathy index of amino acids constituting the hydrophobic tail renders the formation of an emulsion by peptides more likely. By calculating contact number between peptides and decanes, we found that emulsion stability and geometry depends on the structure of amino acids constituting the hydrophobic tail. Analysis of simulation trajectory revealed that emulsions are formed by small nucleation following by fusion to form a bigger emulsion. This study reveals the underlying principle at the molecular level of surfactant peptide ability to form an emulsion with hydrophobic molecules.

Page 89 of 199 | Total Record : 1981

87 88 89 90 91

Filter by Year

2001 2026

Filter By Issues

All Issue Vol 26, No 1 (2026) Vol 25, No 5 (2025) Vol 25, No 4 (2025) Vol 25, No 3 (2025) Vol 25, No 2 (2025) Vol 25, No 1 (2025) Vol 24, No 6 (2024) Vol 24, No 5 (2024) Vol 24, No 4 (2024) Vol 24, No 3 (2024) Vol 24, No 2 (2024) Vol 24, No 1 (2024) Vol 23, No 6 (2023) Vol 23, No 5 (2023) Vol 23, No 4 (2023) Vol 23, No 3 (2023) Vol 23, No 2 (2023) Vol 23, No 1 (2023) Vol 22, No 6 (2022) Vol 22, No 5 (2022) Vol 22, No 4 (2022) Vol 22, No 3 (2022) Vol 22, No 1 (2022) Vol 22, No 2 (2022) Vol 21, No 6 (2021) Vol 21, No 5 (2021) Vol 21, No 4 (2021) Vol 21, No 3 (2021) Vol 21, No 2 (2021) Vol 21, No 1 (2021) Vol 20, No 6 (2020) Vol 20, No 5 (2020) Vol 20, No 4 (2020) Vol 20, No 3 (2020) Vol 20, No 2 (2020) Vol 20, No 1 (2020) Vol 19, No 4 (2019) Vol 19, No 3 (2019) Vol 19, No 2 (2019) Vol 19, No 1 (2019) Vol 18, No 4 (2018) Vol 18, No 3 (2018) Vol 18, No 2 (2018) Vol 18, No 1 (2018) Vol 17, No 3 (2017) Vol 17, No 2 (2017) Vol 17, No 1 (2017) Vol 16, No 3 (2016) Vol 16, No 2 (2016) Vol 16, No 1 (2016) Vol 15, No 3 (2015) Vol 15, No 2 (2015) Vol 15, No 1 (2015) Vol 14, No 3 (2014) Vol 14, No 2 (2014) Vol 14, No 1 (2014) Vol 13, No 3 (2013) Vol 13, No 2 (2013) Vol 13, No 1 (2013) Vol 12, No 3 (2012) Vol 12, No 2 (2012) Vol 12, No 1 (2012) Vol 11, No 3 (2011) Vol 11, No 2 (2011) Vol 11, No 1 (2011) Vol 10, No 3 (2010) Vol 10, No 2 (2010) Vol 10, No 1 (2010) Vol 9, No 3 (2009) Vol 9, No 2 (2009) Vol 9, No 1 (2009) Vol 8, No 3 (2008) Vol 8, No 2 (2008) Vol 8, No 1 (2008) Vol 7, No 3 (2007) Vol 7, No 2 (2007) Vol 7, No 1 (2007) Vol 6, No 3 (2006) Vol 6, No 2 (2006) Vol 6, No 1 (2006) Vol 5, No 3 (2005) Vol 5, No 2 (2005) Vol 5, No 1 (2005) Vol 4, No 3 (2004) Vol 4, No 2 (2004) Vol 4, No 1 (2004) Vol 3, No 3 (2003) Vol 3, No 2 (2003) Vol 3, No 1 (2003) Vol 2, No 3 (2002) Vol 2, No 2 (2002) Vol 2, No 1 (2002) Vol 1, No 3 (2001) Vol 1, No 2 (2001) Vol 1, No 1 (2001) ARTICLE IN PRESS Article in press More Issue

Home Page

OAI Link

Editorial Team

Contact

Reviewer

Google Scholar

Contact Name
-

Contact Email
-

Phone
-

Journal Mail Official
-

Editorial Address
-

Location
Kab. sleman,

Daerah istimewa yogyakarta

INDONESIA

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Home Page

OAI Link

Editorial Team

Contact

Reviewer

Google Scholar

Contact Name -

Contact Email -

Phone -

Journal Mail Official -

Editorial Address -

Location Kab. sleman, Daerah istimewa yogyakarta INDONESIA

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Contact Name
-

Contact Email
-

Phone
-

Journal Mail Official
-

Editorial Address
-

Location
Kab. sleman,

Daerah istimewa yogyakarta

INDONESIA