Garuda - Garba Rujukan Digital

All

Manutech : Jurnal Teknologi Manufaktur

manutech
Website

Published by Politeknik Manufaktur Negeri Bangka Belitung

ISSN : 20895550 EISSN : 26213397 DOI : -

Computer Science & IT Control & Systems Engineering Electrical & Electronics Engineering Industrial & Manufacturing Engineering Mechanical Engineering

Aims Manutech adalah interdisciplinary journal yang mengajak para peneliti dari kalangan para akademisi maupun praktisi dari industri bergabung bersama dan berdiskusi dalam pengembangan keilmuan maupun penerapan teknologi manufaktur dan aspek-aspek lainnya yang terkait. Scope Lingkup jurnal Manutech adalah pada bidang teknologi manufaktur, mesin otomatis (automation), robotika dan elektronika, namun tidak membatasi pada hal ini saja dan dapat melingkupi bidang: Elektronika; Information and Communication Technology (ICT); Mesin dan manufaktur.

Arjuna Subject : -

Articles 208 Documents

1 2 3 4 5

Optimasi Kekasaran Permukaan Proses Pembubutan Baja ST.42 Dengan Menggunakan Metode Taguchi Said Apreza; Zaldy Kurniawan; Muhammad Subhan
Manutech : Jurnal Teknologi Manufaktur Vol. 9 No. 01 (2017): Manutech : Jurnal Teknologi Manufaktur
Publisher : Politeknik Manufaktur Negeri Bangka Belitung

Minimal surface roughness value is the performance to be achieved in the process of CNC NLX 2500, is necessary to regulate variables NLX 2500 CNC process in order to obtain the proper response surface roughness of the workpiece is minimal.research that has been done is to determine the contribution of these variables NLX CNC process in 2500 to reduce the variation of the response surface roughness of the workpiece simultaneously. Moreover, it also made the determination that the proper setting of the variables NLX2500 CNC process in order to obtain the surface roughness of the workpiece is minimal.machining process variable is varied spindle rotation, motion eat, and in the funeral. The experimental design is determined based on the Taguchi method and form of orthogonal L9 (33). Optimization method is used Taguchi. The randomized trial with replication 2 times to overcome interference factors that occur during the machining process.the results showed that to reduce the variation of the response simultaneously, eat motion has the largest percent of the contribution, which amounted to 99.48%, spindle rotation has a percent contribution of 0.0974%, the feeds have a percent contribution of -0.126%.to obtain a surface roughness of the workpiece is minimal, spindle rotation is set at 2748 rpm, eating motion is set at 0.15 mm / rotation, the funeral was adjusted to 0.5 mm.

Iptek Bagi Masyarakat (IBM) Pemanfaatan Teknologi Tepat Guna (TTG) Pada Kelompok Masyarakat Pembuat Lakso Di Kabupaten Bangka Zulfan Yus Andi; Yuliyanto Yuliyanto
Manutech : Jurnal Teknologi Manufaktur Vol. 9 No. 01 (2017): Manutech : Jurnal Teknologi Manufaktur
Publisher : Politeknik Manufaktur Negeri Bangka Belitung

Lakso is one of product’s traditional that made from rice flour served with coconut milk, than mixed of fish meat. Lakso always provided available in stores, events, hotels. Stage of make it from preparation of materials, mixing, molding, make kuah lakso, and ready for eating. Lakso is selling at a price of Rp.3.000 sd. Rp. 5.000 per portion and sell for drying lakso at Rp. 80,000 /kg. Objectives of IbM, to improve quality and production capacity, so be able to improve at partner business management. From survey in 5 month ago, production in lakso has not been met and can not be enough for 75-80% wet’s lakso and 1% for dry’s lakso per month. Issues on partners, there are the production equipment, moulding of lakso and drying (heating from Sun). Other issues concerning the management of lakso provision, or sales. The achievements produced, the cooperation of UKM’s Pak Umar with Polmanbabel, implementation for Polmanbabel’s Tri Dharma that supply machine’s drying for capacity at 4 - 5 kg (rotary rak’s tray system, and aluminum material), research and Community Service by Lecturers and students. The results of activities are understanding, operation and maintenance of production in machine’s provided. the achievement of percentage for drying lakso until 80% and lakso able to survive up to 3 months. Lakso’s dry is able to eat by steaming process.

Analisis Pengaruh Moment Gyroscope Pada Keseimbangan Pendulum Cartessian Muhammad Iqbal Nugraha; J Hartati; W Afridani; Masdani Masdani
Manutech : Jurnal Teknologi Manufaktur Vol. 9 No. 02 (2017): Manutech : Jurnal Teknologi Manufaktur
Publisher : Politeknik Manufaktur Negeri Bangka Belitung

Crane is identical to the pendulum in term of its control mechanism. Based on modelling, these two devices are very similar and therefore, the pendulum can be used as a prototype for controlling a crane. This research aims to control the balance or to reduce the swing on the pendulum by utilizing the moment of gyroscope with a mass pendulum up to 1.5 kg. Gyroscope was designed and made in the form of a disc, in which dimensions and materials used were determined according to the desired moment force. The PID controller was used to control the speed of gyroscope based on the angle of the pendulum (?). Based on the results of the experiment, it was obtained that the resulting settling time was 2.29 times faster than without control in average. The overshoot and rise time resulted by the system using gyroscope were very similar to the system which is without gyroscope. However, the steady state error was totally eliminated. It can be concluded that the moment of gyroscope is able to be used for controlling the pendulum or crane.

Mobile Robot Dengan Pengontrolan Perintah Suara Berbasis Android Eko Sulistyo
Manutech : Jurnal Teknologi Manufaktur Vol. 9 No. 02 (2017): Manutech : Jurnal Teknologi Manufaktur
Publisher : Politeknik Manufaktur Negeri Bangka Belitung

Control of mobile robot manually using remote control connected with cable has constraints that limited space of robot movement. For that developed mobile robot control system using bluetooth communication. The purpose of this research is to create a mobile robot control system through wireless communication using voice command instruction via application on Android using microcontroller type Arduino Mega2560. The methodology in this research is the voice instruction will be recorded by the application on Android, then matched with the database and then converted into characters in the form of strings and sent via bluetooth transmitter on Android to bluetooth receiver on mobile robot to be executed by program made on microcontroller robot. The results obtained include mobile robot can move to follow voice command instruction that is given include command forward, backward, turn left and right only for one movement while in test result got error of movement equal to 1.55% with response time 4-7 second because the process of recording and translation of voice instructions on Android and also influenced by noise or other sounds that are not desired.

Remotely Operated Vehicle (ROV) Untuk Eksplorasi Bawah Air Di Lingkungan Industri Perkapalan R A Septian; A Rahmania; M I Nugraha; Yudhi Yudhi
Manutech : Jurnal Teknologi Manufaktur Vol. 9 No. 02 (2017): Manutech : Jurnal Teknologi Manufaktur
Publisher : Politeknik Manufaktur Negeri Bangka Belitung

Remotely Operated Vehicle (ROV) is one of the robots that are being developed in Indonesia for exploring underwater potential. In this final project, the ROV was designed and controlled by Arduino for diving underwater with maximum depth of 30 meters. The application of ROV is that to take pictures and record video of underwater environment in real time by using camera monitored through a PC. The construction and the electronics device of the ROV were made waterproof. The actuator used was bilge pump motor 1100GPH 12 Volt as thruster motor. The thruster driver used was a two channel-relay and the vision system of robot was a CCD camera. Based on the results, it was obtained that the ROV was able to move according to the commands provided by operator using a remote control. At three meters depth, the robot can move forward with average speed of 0.161m/s. For up and down movement at 3 meters depth, the robot can go up with average speed of 0.09 m/s and down with average speed of 0.17 m/s. From the data, it can be concluded that the ROV can maneuver and use the camera properly.

Perancangan Sistem Kontrol Kecepatan Motor DC Dengan PID Labview 2010 Fauzy Fauzy; Sugiatmo Kasmungin
Manutech : Jurnal Teknologi Manufaktur Vol. 9 No. 02 (2017): Manutech : Jurnal Teknologi Manufaktur
Publisher : Politeknik Manufaktur Negeri Bangka Belitung

The stability of the system is the main objective for Control System Design criteria. PID control with closed loop system is the one of control which can improve the stability of the system from disturbance effect. In this study, DC Motor Speed Control is designed with PID LabVIEW 2010 Software and Proximity Sensor as a closed loop feedback. The system allows the operator to control speed of DC Motor from LabVIEW front panel which automatically stabilized when load ?which usually slow down the speed of DC Motor, applied. PID LabVIEW 2010 generates voltage output 0-5Vdc and drives DC Motor through analog output channel from NIDAQ 600, which received by Non-Inverting Amplifier and amplified to 0-12Vdc output. PID Control with Closed Loop system may dampen the speed response second order of DC Motor to have value of overshoot number ? 0 with steady state error of ?2%. The system feedback can stabilize this condition from outside interference. The result of this speed control system has success criteria of overshoot (Mp) = 0 and Error Steady State (Ess) = 0.82%.

Implementasi Kincir Angin Savonius 2 Tingkat Menggunakan Generator Magnet Permanen Jefri Lianda; Hikmatul Amri
Manutech : Jurnal Teknologi Manufaktur Vol. 9 No. 02 (2017): Manutech : Jurnal Teknologi Manufaktur
Publisher : Politeknik Manufaktur Negeri Bangka Belitung

This paper focuses on improving the performance of a two-tiered windmill savonius to generate electricity through a permanent magnet generator. This study used an experimental method, taking into account the number and angle of the wind turbine Savonius two levels. The study was conducted at wind speed conditions of about 2.85 m / s to 6.42 m / s. Dimensions of windshield savonius blades with a width of 45 cm and a height of 50 cm. The wind turbine is installed with a height of 3.5 meters from the ground. This study uses a gearbox with a ratio of 1: 3.This study produces a maximum power of 95 watts. The average voltage generated 13.75 volts AC to 19.52 volts AC. The energy supplied to the battery uses a battery charger control (BCR).

Analisa Getaran Akibat Kerusakan Deep Grove Ball Bearing Seri 6003RS Muhamad Riva’i; Nanda Pranandita
Manutech : Jurnal Teknologi Manufaktur Vol. 9 No. 02 (2017): Manutech : Jurnal Teknologi Manufaktur
Publisher : Politeknik Manufaktur Negeri Bangka Belitung

Measurement of the damage of elements in bearing can be by measuring the vibration generated in the form of a frequency signal when the pad is rotating. Measurement of vibration on the bearing by using vibration measuring instrument. Damage to the rolling bearing includes damage to the cage, outer ring, inner ring and balls. The rolling bearings used in this study are deep groove ball bearing type 6003 RS with internal diameter (d) = 17 mm, outer diameter (D) = 35 mm, bearing thickness (B) = 10, number of rolling elements (Nb) = 10 pieces, and the diameter of the rolling element (Bd) = 4.75 mm. In the rotation of the bearing (Fr) = 2003 rpm (33.38 Hz) we found the experimental results of bearings that have been damaged in the outer race at 138 Hz frequency, inner race damage at 196 Hz frequency, (ball) at a frequency of 88.8 Hz and cage damage at a frequency of 13.8 Hz.

Tinjauan Performansi Bubut Doll LT13 Terhadap Penyimpangan Kebulatan Benda Kerja Ariyanto Ariyanto; Husman Husman; Yuli Dharta
Manutech : Jurnal Teknologi Manufaktur Vol. 9 No. 02 (2017): Manutech : Jurnal Teknologi Manufaktur
Publisher : Politeknik Manufaktur Negeri Bangka Belitung

The industry manufacture with high quality and able to pruduce the workpicece with high quality In industry manufacture are very necessary. The use of high quality machines should be supported by the ability to operate and the ability to perform maintenance, this ability is useful to maintain the condition of the machine in order to produce good quality workpieces. Politeknik Manufaktur Negeri Bangka Belitung has several high quality machine tools, one type of machine tools usually use is lathe machine doall LT13 with total have six units. this machine Used to support education and to produce spare parts. Doall LT13 lathes have been used for 22 years, during that period there may be deviation of machine geometry, deviations that occur can lead to decreased quality of the resulting workpiece. This study aims to determine the feasibility of the machine by measuring the roundness of the spicemen of the process of turning, the roundness of the specimen is analyzed by using the minimum circle method. From the roundness testing performed on the doall lt 13 the result? that can be achieved as follows 0,082 mm at lathe number 8, 0,073 mm at lathe number 5, 0,057 mm at lathe number 7, 0,051 mm at lathe? number 2, 0,048 mm at lathe number 6 and 0,046 mm at lathe number 3.

Rancang Bangun Media Bantu Pemeriksa Penyimpangan Pada Poros Robert Napitupulu; Rodika Rodika; Febrian Arif; M Romario4; Reni Febrianti
Manutech : Jurnal Teknologi Manufaktur Vol. 9 No. 02 (2017): Manutech : Jurnal Teknologi Manufaktur
Publisher : Politeknik Manufaktur Negeri Bangka Belitung

Machine Improvement Element (PEM) is one of the competencies that must be possessed by students Polytechnic Manufacturing of Bangka Belitung (PolmanBabel), in the hope that the students can repair the damage of machine element such as the shaft, peg, gear and thread well. Currently the process of repairing the engine element is constrained in the inspection tools of mesi element improvement such as the shaft. This study aims to design auxiliary media for aberration checks on the axis and can examine alignment and alignment deviations on axis. The stages of this research starts from the collection of data and information, then designing tools, making tools, assembling, and testing. Based on the results of design and testing of the aberration check axis on the axis obtained the magnitude of averages 0.23mm and the magnitude of deviation celery averages of 0.12.

Page 3 of 21 | Total Record : 208

1 2 3 4 5

Filter by Year

2016 2025

Filter By Issues

All Issue Vol. 17 No. 02 (2025): Manutech: Jurnal Teknologi Manufaktur Vol. 17 No. 01 (2025): Manutech: Jurnal Teknologi Manufaktur Vol. 16 No. 02 (2024): Manutech: Jurnal Teknologi Manufaktur Vol. 16 No. 01 (2024): Manutech: Jurnal Teknologi Manufaktur Vol. 15 No. 02 (2023): Manutech: Jurnal Teknologi Manufaktur Vol. 15 No. 01 (2023): Manutech: Jurnal Teknologi Manufaktur Vol. 14 No. 02 (2022): Manutech: Jurnal Teknologi Manufaktur Vol. 14 No. 01 (2022): Manutech: Jurnal Teknologi Manufaktur Vol. 13 No. 02 (2021): Manutech: Jurnal Teknologi Manufaktur Vol. 13 No. 01 (2021): Manutech: Jurnal Teknologi Manufaktur Vol. 12 No. 02 (2020): Manutech: Jurnal Teknologi Manufaktur Vol. 12 No. 01 (2020): Manutech: Jurnal Teknologi Manufaktur Vol 12 No 01 (2020): Manutech : Jurnal Teknologi Manufaktur Vol. 11 No. 02 (2019): Manutech : Jurnal Teknologi Manufaktur Vol. 11 No. 01 (2019): Manutech: Jurnal Teknologi Manufaktur Vol. 10 No. 02 (2018): Manutech : Jurnal Teknologi Manufaktur Vol. 10 No. 01 (2018): Manutech : Jurnal Teknologi Manufaktur Vol. 9 No. 02 (2017): Manutech : Jurnal Teknologi Manufaktur Vol. 9 No. 01 (2017): Manutech : Jurnal Teknologi Manufaktur Vol. 8 No. 02 (2016): Manutech : Jurnal Teknologi Manufaktur Vol. 8 No. 01 (2016): Manutech : Jurnal Teknologi Manufaktur More Issue

Home Page

OAI Link

Editorial Team

Contact

Reviewer

Google Scholar

Contact Name
Made Andik Setiawan

Contact Email
made.andik.s@gmail.com

Phone
-

Journal Mail Official
ManutechJournal@gmail.com

Editorial Address
-

Location
Kab. bangka,

Kepulauan bangka belitung

INDONESIA

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Home Page

OAI Link

Editorial Team

Contact

Reviewer

Google Scholar

Contact Name Made Andik Setiawan

Contact Email made.andik.s@gmail.com

Phone -

Journal Mail Official ManutechJournal@gmail.com

Editorial Address -

Location Kab. bangka, Kepulauan bangka belitung INDONESIA

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Contact Name
Made Andik Setiawan

Contact Email
made.andik.s@gmail.com

Phone
-

Journal Mail Official
ManutechJournal@gmail.com

Editorial Address
-

Location
Kab. bangka,

Kepulauan bangka belitung

INDONESIA