Article Per Year (5 Year)
p-Index From 2021 - 2026
1.203
P-Index
This Author published in this journals
All Journal Metalurgi Jurnal Sains Materi Indonesia
Irawan, Januar
Unknown Affiliation
Engineering Industrial & Manufacturing Engineering Materials Science & Nanotechnology

Published : 6 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 6 Documents
Search

 1 
The Effect of pH and Sodium Silicate Dosage on the Separation of Magnesium and Lithium from Artificial Brine Water Using Chemical Precipitation Techniques Lalasari, Latifa Hanum; Sulistiyono, Eko; Harjanto, Sri; Irawan, Januar; Firdiyono, Florentinus; Arini, Tri; Andriyah, Lia; Suharyanto, Ariyo; Natasha, Nadia Chrisayu; Yunita, Fariza Eka
Metalurgi Vol 38, No 3 (2023): Metalurgi Vol. 38 No. 3 2023
Publisher : National Research and Innovation Agency (BRIN)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.55981/metalurgi.2023.728

Abstract

This study aims to report the findings of an investigation into the separation of lithium and magnesium ions in the artificial brine water. The artificial brine water contains concentrations of magnesium, calcium, and lithium cations that closely resemble the concentrations seen in natural brine water sourced from Gunung Panjang using magnesium chloride, calcium chloride, and lithium chloride p.a. The objective of this experiment was to investigate the impact of pH and the addition of sodium silicate on the separation of magnesium and calcium ions from lithium ions in artificial brine water. The best outcomes were achieved when the pH of the brine water was set at 10, and sodium silicate was added in a stoichiometric ratio of 219%. These parameters led to a lithium content of 90.06%, magnesium removal of  70.32%, and a Mg/Li ratio of 6.29, indicating a substantial presence of magnesium ions precipitated as solids with pyroxene (MgSiO3) phase. This research also succeeded in increasing the lithium content by 94.28% and reducing the Mg/Li ratio to 4.96 after the precipitated solids were subjected to a water-leaching process.
Kinetic of Dissolution of Nickel Limonite Calcine by Sulfuric Acid Solution Setiawan, Iwan; Nabilah, Annisa; Oediyani, Soesaptri; Subagja, Rudi; Irawan, Januar; Sampoerno, Arief Budi; Yunita, Fariza Eka; Suharyanto, Ariyo; Syahid, Adi Noer
Metalurgi Vol 38, No 3 (2023): Metalurgi Vol. 38 No. 3 2023
Publisher : National Research and Innovation Agency (BRIN)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.55981/metalurgi.2023.740

Abstract

Currently, more than 60% of nickel processing is carried out using nickel sulfide as a raw material. Nonetheless, due to the depletion reserves of nickel sulphide, nickel laterite has drawn a lot of interest to be processed as raw material. Nickel laterite in Indonesia is generally found in low grades, with nickel concentration of <1.15%. One method of treating nickel limonite is leaching in a sulfuric acid solution. This study aims to determine the reaction rate in the leaching process of calcine nickel limonite and the effect of sulfuric acid concentration and leaching temperature on the percent nickel extraction. In this research, the limonite ore from Pomalaa, Southeast Sulawesi, Indonesia, which has undergone a reduction process, was used as raw material. This research was conducted by leaching method on nickel limonite calcine using sulfuric acid reagent with 0.2, 0.5, and 1 M concentration variation, temperature variations of 60, 70, and 90°C, stirring speed 500 rpm, and %S/L (w/w) 10%. In this leaching research, the activation energy obtained at a sulfuric acid concentration of 0.2, 0.5, and 1 M are 13,7379 kJ/mol, 19,7582 kJ/mol, 20,3161 kJ/mol, respectively. The leaching process of nickel limonite calcine was controlled by diffusion. The optimum nickel extraction percentage in this study was 97.45%, obtained at a concentration of 1 M sulfuric acid, temperature of 70 °C, and leaching time of 240 minutes.
MORPHOLOGY AND RESISTIVITY VALUE OF FLOURINE-DOPED TIN OXIDE (FTO) USING INDONESIAN LOCAL DIMETHYLTIN DICHLORIIDE (DTMC) PRECURSORS Rizki, Apti Mira; Yunita, Fariza Eka; Lalasari, Latifa Hanum; Irawan, Januar; Arini, Tri; Firdiyono, Florentinus; Andriyah, Lia; Natasha, Nadia Chrisayu; Yuwono, Akhmad Herman
Metalurgi Vol 37, No 3 (2022): Metalurgi Vol. 37 No. 3 Desember 2022
Publisher : National Research and Innovation Agency (BRIN)

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1481.393 KB) | DOI: 10.14203/metalurgi.v37i3.685

Abstract

Transparent Conductive Oxide (TCO) is the main component for solar cell fabrication. One of the promising types of TCO is fluorine-doped tin oxide (FTO). The method used in depositing the conductive layer of FTO is spray pyrolysis with an ultrasonic nebulizer. The precursor is a local Indonesian product, dimethyl tin dichloride (DMTC), with doping ammonium fluoride (NH4F). The variable that used in this study were variations in deposition time (5. 10. 15. 20, and 25 minutes) with a fixed substrate temperature at 300°C and doping variations (un-doped, 2 wt.% doped and 8 wt.% doped) to see the effect of adding F doping to the precursor solution. The resistivity value with deposition time of 5. 10. 15. 20 and 25 minute (2 wt.% doped) is 0.218x100; 0.449x10-1; 1,567x10-2; 0.676x10-2 0.377x10-2 Ω.cm. For doping variations (un-doped, 2 wt% doped and 8 wt% doped) the value is 0.883x10-2; 0.377x10-2; 0.506x10-3 Ω.cm. There is a decreasing trend in the resistivity values obtained along with the increase in deposition time and the addition of doping to obtain better conductive properties. The grain size will increase with increasing deposition time and the addition of doping. The optimum resistivity value obtained in this study was 0.377x10-2 Ω.cm, obtained at the deposition time of 25 minutes with 2 wt.% doping.
IRON REMOVAL PROCESS FROM NICKEL PREGNANT LEACH SOLUTION USING SODIUM HYDROXIDE Zunaidi, Mochamad Afriansyah; Setiawan, Iwan; Oediyani, Soesaptri; Irawan, Januar; Rhamdani, Ahmad Rizky; Syahid, Adi Noer
Metalurgi Vol 37, No 3 (2022): Metalurgi Vol. 37 No. 3 Desember 2022
Publisher : National Research and Innovation Agency (BRIN)

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1538.744 KB) | DOI: 10.14203/metalurgi.v37i3.665

Abstract

Indonesia is a country that has abundant mineral resources, including nickel resources in laterite ore. Nickel demand has risen significantly because of the need for nickel precursors for battery production. Nickel laterite can be processed via the hydrometallurgical route to obtain nickel precursor by leaching the laterite ore with an acid solution to produce a nickel-rich solution or Pregnant Leach Solutions (PLS). This nickel-rich solution is then processed by precipitation with a base solution to make its hydroxides known as Mixed Hydroxides Precipitate (MHP). MHP is the main product that contains nickel and cobalt for making the material for a lithium battery. PLS usually contain iron impurity, which also dissolves when the ore is leached. Therefore, the iron needs to be separated to make high-purity MHP. To solve this problem, synthetic PLS contained nickel, cobalt, and iron, and their concentration was simulated to match the general PLS composition. From the experiment, it was observed that iron could be precipitated at two stages at solution pH of 3 and 3.5 using 2.5 M NaOH solution. After that, nickel and cobalt can be precipitated at higher pH. To study the effect of pH and temperature on the yield of nickel and cobalt precipitation, precipitation at pH of 7, 8, and 9; and temperature of 70, 80, and 90 °C was conducted. The results show that the highest yield was obtained at a pH of 9 and temperature of 90 °C, with precipitation yield of nickel and cobalt at 99.03% and 98.78%, respectively.
Copper Dissolution Rate of Modified Self-Polishing Antifouling Paint with Cerium Oxide Nikitasari, Arini; Irawan, Januar; Priyotomo, Gadang; J.W. Soedarsono; Riastuti, Rini
Jurnal Sains Materi Indonesia Vol. 26 No. 2 (2025): Jurnal Sains dan Materi Indonesia
Publisher : BRIN Publishing (Penerbit BRIN)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.55981/jsmi.2025.8753

Abstract

The main objective of the work is to substitute SeaNine 211 in self-polishing antifouling (SPA) paint formulations for marine coating using cerium oxide as a co-biocide. The development of SPA paint with cerium oxide as a co-biocide is expected to significantly improve the environmental friendliness and efficacy of antifouling paints. The preparation of modified SPA paint was undertaken by incorporating the cerium oxide with various concentrations (0.1, 0.3, and 0.5 wt.%) in the SPA paint formulation without SeaNine 211. The copper dissolution rate determines the efficacy of antifouling paint, where the greater the copper release rate, the greater the efficacy of the antifouling paint. The leached-out test results obtained suggest that with an increase of 0.1% wt in the concentration of cerium oxide, there was an improvement in the copper dissolution rate. It was also observed that the mild steel specimens were coated with modified SPA paint when immersed in the seawater for 7 days for testing. The properties were observed by utilizing scanning electron microscopy (SEM). An improvement in the copper dissolution rate was found, as shown by cerium oxide SPA paint when contrasted with bare paint. The contact angle test finding also suggests that adding 0.1% wt of cerium oxide to the SPA paint will increase the dissolution rate of copper. This work could provide insight into developing an environmentally friendly antifouling paint co-biocide.
Study of Iron and Calcium Removal on Manganese Sulfate Precursors for Battery Cathode Raw Material Applications Hakim, Agsel Fauzia; Andriyah, Lia; Oediyani, Soesaptri; Lalasari, Latifa Hanum; Sulistiyono, Eko; Irawan, Januar; Arini, Tri; Yunita, Fariza Eka; Suharyanto, Ariyo; Setiawan, Iwan; Firdiyono, Florentinus; Yuwono, Akhmad Herman
Metalurgi Vol 39, No 2 (2024): Metalurgi Vol. 39 No. 2 2024
Publisher : National Research and Innovation Agency (BRIN)

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.55981/metalurgi.2024.753

Abstract

Global battery sales are expected to reach $310.8 billion in 2027, up 14.1% from 2020. 95% of the world's batteries are lead-acid, lithium-ion, or nickel-based. One of the most popular batteries on the global market is lithium-ion, which uses MnSO4 powder as its cathode raw material. Manganese sulfate-based lithium-ion batteries can be made using Indonesian resources, specifically manganese ore from Trenggalek. Trenggalek manganese ore is of poor quality and contains impurities, primarily Fe and Ca. To produce 98% powder manganese sulfate, the solution is prepared, reduced with briquette charcoal, leached, precipitated, carbonated, and crystallised. NH4OH reagent is used to remove Fe through precipitation, and the carbonatation process is employed to eliminate Ca, resulting in 97.237% purity of manganese sulfate powder product. This outcome is achieved under precipitation process conditions of [NH4OH 2M], T = 80 °C, pH = 4, t =180 minutes, while carbonatation process conditions are T=50 °C, t = 120 minutes.
Co-Authors Akhmad Herman Yuwono Andriyah, Lia Eko Sulistiyono, Eko Florentinus Firdiyono Gadang Priyotomo Hakim, Agsel Fauzia Iwan Setiawan J.W. Soedarsono Lalasari, Latifa Hanum NABILAH, ANNISA Natasha, Nadia Chrisayu Nikitasari, Arini Rhamdani, Ahmad Rizky Rini Riastuti, Rini Rizki, Apti Mira Sampoerno, Arief Budi Soesaptri Oediyani Sri Harjanto Subagja, Rudi Suharyanto, Ariyo Syahid, Adi Noer Tri Arini, Tri Yunita, Fariza Eka Zunaidi, Mochamad Afriansyah