Claim Missing Document
Check
Articles

Found 14 Documents
Search

Analisa Pengaruh Variasi Komposisi Gas Pelindung Terhadap Hasil Pengelasan Gmaw-Short Circuit dengan Penggunaan Mesin Khusus Regulated Metal Deposition (RMD) Hilmy, Zakwan; Syahroni, Nur; Hadiwidodo, Yoyok S.
IPTEK Journal of Proceedings Series No 2 (2018): The 2nd Conference on Innovation and Industrial Applications (CINIA 2016)
Publisher : Institut Teknologi Sepuluh Nopember

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.12962/j23546026.y2018i1.3385

Abstract

Salah satu faktor yang menentukan hasil pengelasan adalah gas pelindung (Shielding Gas). Jenis dan komposisi gas pellindung pada pengelasan memberikan hasil yang berbeda antara satu dengan lainnya. Moda transfer GMAW- short circuit sering tidak dilakukan karena memiliki tingkat kesukaran yang tinggi. Oleh sebab itu perusahaan listrik Miller membuat terobosan dengan menciptakan RMD (Regulated Metal Deposition). Oleh karena itu diadakan penelitian yang bertujuan mengetahui bagaimana pengaruh variasi gas pelindung elektroda yang digunakan pada proses pengelasan GMAW dengan menggunakan mesin RMD (Regulated Metal Deposition) dengan transfer moda secara short circuit terhadap hasil pengelasan pipa baja ASTM A106 dengan komposisi Ar+CO2 (90%+10%, 80%+20%, 75%+15%, 0%+100%) pada posisi Flat, horizontal, vertical, dan overhead di bagian root. Analisa terhadap hasil pengelasan menunjukan bahwa kriteria yang diamati seperti hardness, level spatter, tebal weld metal, serta bentuk dan konsistensi hasil pengelasan (weld bead) mengalami perubahan terhadap penambahan komposisi gas CO2. 100% gas CO2 menghasilkan nilai kekerasan terendah yaitu 186.46 HV dan level spatter tertinggi yaitu 12.27%. Bentuk weld bead yang tidak konsisten dihasilkan seiring bertambahnya gas CO2, hal ini karena busur las yang dihasilkan menjadi tidak stabil sehingga menyulitkan welder.
Analisis Kelelahan pada Struktur Bravo Wellhead Platform dengan Penambahan Luas Sub-Cellar Deck Menggunakan Metode Cummulative Damage dan Fracture Mechanics Bagus Panuntun; Nur Syahroni; Rudi Walujo Prastianto
Jurnal Teknik ITS Vol 7, No 2 (2018)
Publisher : Direktorat Riset dan Pengabdian Masyarakat (DRPM), ITS

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (393.447 KB) | DOI: 10.12962/j23373539.v7i2.32985

Abstract

Offshore fixed platform didefinisikan sebagai platform yang berada di atas permukaan air dan ditopang Piles dari dasar laut, dan juga lebih sering menerima beban berulang  sehingga menyebabkan kelelahan struktur. Kelelahan sturktur merupakan suatu proses dari kumulatif kerusakan yang disebabkan oleh pengulangan fluktuasi beban yang dapat mengakibatkan keruntuhan meskipun beban yang diterima tidak melebihi batas maksimum untuk beban statik. Tugas akhir ini bertujuan untuk menganalisis kelelahan struktur Bravo Wellhead Platform yang beroperasi di Selat Madura  dengan kedalaman perairan di lokasi tersebut adalah 180.0 ft terhadap MSL (Mean Sea Level). Dalam tugas akhir ini penulis menggunakan metode cumulative damage dan fracture mechanics. Pada metode cummulative damage didapatkan umur kelelahan terpendek dibawah MSL sebesar 89,342 tahun pada tubular joint 303. Selanjutnya, dilakukan analisa lokal dan penambahan crack menggunakan metode fracture mechanics terhadap tubular joint 303. Tubular joint paling kritis selanjutnya dianalisa menggunakan metode fracture mechanics dengan memberikan crack sebesar a = 0.25 mm, ???? ⁄2????= 0.15 dan didapatkan umur kelelahannya. Kemudian diketahui selisih umur kelelahan dari kedua metode ini sebesar 22,241 tahun. Kesimpulan dari tugas akhir ini adalah retak yang nantinya ditambahkan ke dalam struktur dapat mengurangi service life struktur secara signifikan.
Analisis Pengaruh Variasi Flow Rate Gas Pelindung Pada Pengelasan FCAW-G Terhadap Struktur Mikro Dan Kekuatan Mekanik Sambungan Material Grade A Nabielah Khiyaarul A-immah; Nur Syahroni; Yoyok Setyo Hadiwidodo
Jurnal Teknik ITS Vol 7, No 2 (2018)
Publisher : Direktorat Riset dan Pengabdian Masyarakat (DRPM), ITS

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (270.664 KB) | DOI: 10.12962/j23373539.v7i2.33035

Abstract

Pengelasan merupakan hal yang tidak dapat dipisahkan dari dunia industri maritim terutama perkapalan karena hampir keseluruhan konstruksi badan kapal disambung dengan cara dilas. Salah satu metode pengelasan yang paling sering digunakan adalah FCAW (Flux Cored Arc Welding). Pengelasan FCAW sering digunakan karena produktivitasnya yang tinggi. Dalam penerapannya, pengelasan FCAW dapat digunakan dengan atau tanpa gas pelindung. Gas pelindung berfungsi sebagai pelindung logam las agar tidak terjadi interaksi dengan udara sekitar juga mempengaruhi kestabilan nyala busur yang dapat memengaruhi kinerja dari welder pada saat mengelas. Dalam penelitian ini akan dianalisis bagaimana pengaruh variasi flow rate gas pelindung terhadap struktur mikro, kekerasan, dan kekuatan tariknya. Variasi flow rate gas pelindung yang digunakan adalah 14 L/menit, 16 L/menit, dan 18 L/menit. Dari hasil pengujian akan didapatkan hasil pengaruh variasi flow rate gas pelindung terhadap struktur mikro, kekerasan, dan kekuatan tarik.
Influence Analysis of Shielding Gas Flow Rate and Purity Level Variation on GMAW Welding Process to Microstructure of Alumunium 5083 Nur Syahroni; Sadewa Sechan Winando; Yeyes Mulyadi
International Journal of Offshore and Coastal Engineering (IJOCE) Vol 5, No 1 (2021)
Publisher : DRPM (Direktorat Riset dan Pengabdian kepada Masyarakat) ITS

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.12962/j2580-0914.v4i3.9954

Abstract

Aluminium is a commonly used material in construction and transportation industries. The advantages of using the aluminium material are its light weight, corrosion resistant, and the capability to form an alloy with another metal. Therefore, the aim of this research is to analyze the influence of shielding gas flow rate and purity level variation to mechanical properties and microstructure of the welded material. The welding process used on this research was the GMAW method. The material used was aluminium 5083 series with 300 mm x 150 mm x 8 mm dimensions. The shielding gases used were high purity (HP) and ultra-high purity (UHP) argon (Ar). The variations of shielding gas flow rate used were 16, 18, dan 20 litre/minutes. Based on the tensile test that has been done, the variation of UHP argon gas with 20 litre/minute flow rate had the best result with yield strength of 217,32 MPa and ultimate strength of 295,83 MPa. The result of the micro photos showed that the GMAW method produced small dots where the dots were Mg2Si formation, which the greater number of smaller size dot produced would increase the mechanical properties of  the material.
Saddle Strength Analysis on Jacket Structure During Roll Up Procedures in Fabrication Phase Nabila Defriana; Handayanu Handayanu; Nur Syahroni
International Journal of Offshore and Coastal Engineering (IJOCE) Vol 6, No 2 (2022)
Publisher : Pusat Publikasi Ilmiah Institut Teknologi Sepuluh Nopember

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.12962/j25800914.v6i2.14772

Abstract

Offshore platform is a structure that serves as a well drilling facility to explore, extract, store and process petroleum and gas located under the seabed. There are several phases in theconstruction of offshore structures (fixed jacket platform) from preparation to construction. Fabrication phase is the earliest stage in the manufacture of a fixed offshore platform (jacketstructure) which is carried out by the fabricator. One of the procedures at the fabrication phase is roll up procedure. In this final project research, an analysis will be carried out regarding the configuration of the rigging, crane, and sadle support used in the jacket structure during roll up procedure. After the analysis of jacket structure modeling using the SACS software, the results of rigging configuration can be obtained, which were the slingsspesifications used to connect the structure with cranes, with sling diameter of 2.75 inch and SWL value of 64 MT. As for the sling used to connect the jacket with winch has a diameter of 1.5 inch snd SWL value of 18 MT. Furthermore, the cranes used have a capacity of 75 and 78 MT, respectively. In the load analysis of the jacket structure, it was found that saddle support received the largest reaction when the jacket was at an 80-degree slope with the largest reaction value of 102.74 MT. In the saddle support local analysis, the result of maximum equivalent von-mises stress obtained was 43,486 MPa, with the saddle allowable stress of 345 Mpa, therefore the UC value of 0.24 can be obtained.
Experimental Study of Electrode Variation Effect on Connection Strength for Underwater Welding Benedictus Arif Wicaksono; Nur Syahroni; Yeyes Mulyadi
International Journal of Offshore and Coastal Engineering (IJOCE) Vol 6, No 2 (2022)
Publisher : Pusat Publikasi Ilmiah Institut Teknologi Sepuluh Nopember

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.12962/j25800914.v6i2.14773

Abstract

SMAW welding has various electrodes that can be used in underwater welding. This study will analyze the influence of electrode type on mechanical properties and the influence ofwelding position on the mechanical properties of joints for underwater welding. This experiment results show that the E7016 electrode pull test has a superior value than the E6013 and E7018 electrodes; when compared between E6013 and E7016, it is reasonable if the E7016 is stronger than E6013 and the frequency level is higher than E6013 even if it already uses a different amper. However, if the E7016 electrode compared to the E7018 is still superior to the E7016 electrode using the same voltage and amper. In addition, the results of macro test observations show that welding using the E7018 electrode has lower porosity levels than E7016 electrodes, while with the same experiment results, the tensile strength of the E7016 is superior to the E7018. So that the power value of E7016 electrodes can be superior to E7018 in this experiment is not only based on porosity that occurs but also slag and imperfect penetration also determines the strength of welding results by using E7016 electrodes.
Pelatihan AutoCAD 3D Secara Online untuk Masyarakat Terdampak Covid-19 Yoyok Setyo Hadiwidodo; Nur Syahroni; Handayanu; Imam Rochani; Herman Pratikno; Madi Madi
Jurnal Pengabdian Pada Masyarakat Vol 7 No 1 (2022): Jurnal Pengabdian Pada Masyarakat
Publisher : Universitas Mathla'ul Anwar Banten

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (504.082 KB) | DOI: 10.30653/002.202271.5

Abstract

The Covid-19 pandemic has had an impact on society, especially in the field of education. Various educational activities are carried out online, so the Service Team holds online AutoCAD 3D training activities to add insight into education and technical design for communities affected by Covid-19. The stages of the program that have been implemented are, the first stage of pre-training which consists of an online survey to communities affected by COVID-19, the design of the AutoCAD 3D training module, and preparation of making online media such as websites, Instagram, and YouTube. The second stage is training which consists of registration of affected communities, online media publications, and online training using online media meetings that are integrated with websites, Instagram, and YouTube. The third stage is post-training in the form of an evaluation to analyze the satisfaction of people who have attended AutoCAD 3D Online training. The results of the analysis of community satisfaction with the facilitators, facilities, presenters, and materials stated that they were 100% very satisfied and satisfied. In addition, the training was also 100% running as expected based on the results of the participant's evaluation.
MICROPLASTIC CHARACTERISTIC FOUND IN GASTROINTESTINAL TRACT OF PELAGIC AND DEMERSAL FISHES IN TUBAN, EAST JAVA Dewi Hidayati; Fauziah F; Aunurohim A; Nova Maulidina Ashuri; Edwin Setiawan; Yeyes Mulyadi; Nur Syahroni; Marita Ika Joesidawati; Suwarsih S
Journal of Marine-Earth Science and Technology Vol. 4 No. 1 (2023): April
Publisher : Marine & Earth Science and Technology Research Center, DRPM, ITS

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.12962/j27745449.v4i1.648

Abstract

Regular monitoring of microplastics contamination in marine biota have been concerned in the world, since its tiny size can be swallowed direct or indirectly and lead health problems. Tuban waters is the one of Indonesia's coastal and marine fisheries areas with high risk of microplastic pollution due to their highly anthropogenic activities. We investigated the microplastic in the digestive tracts of pelagic and demersal fishes in Tuban sea waters.  Microplastic in fish sample guts were observed under microscope and the type of polymer were examined using FT-IR. This study reveals that number of microplastic in digestive tract of pelagic fishes were higher than demersal fishes. The dominant form was fiber (62%) with black color and dominant size ranging from 100-500 um (72%). The types of polymers found were polyethylene and polyamide.
Pelatihan Ketrampilan Pengelasan Tingkat Dasar Lanjutan (SMAW 2G & 2F) untuk Keluarga Pra-Sejahtera Di Sekitar Kampus ITS Surabaya Nur Syahroni; Handayanu; Yeyes Mulyadi; Imam Rochani; Kriyo Sambodho; M. Zikra Yuniarto; Rudi Walujo P; Yoyok Setyo H; Sholihin
Sewagati Vol 2 No 2 (2018)
Publisher : Pusat Publikasi ITS

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (836.466 KB)

Abstract

Jumlah keluarga pra-sejahtera di dua kelurahan sekitar ITS, yaitu Kelurahan Keputih dan Gebang Putih masih cukup banyak, dimana terdapat indikasi kuat bahwa faktor pengangguran menjadi penyebab utamanya. ITS bisa berperan untuk mengatasi hal tersebut dengan melakukan pelatihan ketrampilan khusus kepada masyarakat di sekitar ITS terutama untuk keluarga pra-sejahtera, sehingga bisa membuka lapangan pekerjaan yang sesuai dengan ketrampilan yang didapatkan dari pelatihan tersebut. Laboratorium Struktur, Material dan Produksi Bangunan Laut (SMPBL) di Departemen Teknik Kelautan FTK-ITS mempunyai peralatan pengelasan yang cukup lengkap serta didukung teknisi dan instruktur yang berpengalaman bisa digunakan untuk mendukung program pelatihan khususnya di bidang pengelasan tingkat dasar. Program pelatihan pengelasan tingkat dasar telah sukses dilakukan pada tahun 2015, 2016 dan 2017 serta mendapatkan respon yang sangat positif dari para peserta yang mendapatkan manfaat langsung dari pelatihan ini. Tingkat ketrampilan yang didapatkan peserta pada pelatihan tersebut masih sangat dasar, sedangkan untuk menghadapi persaingan kerja di bidang pengelasan diperlukan ketrampilan yang lebih tinggi. Untuk itu ketrampilan peserta yang telah mengikuti pelatihan dasar sebelumnya perlu diupgrade ke tingkat yang lebih tinggi dengan memberikan pelatihan pengelasan dasar lanjutan sampai dengan posisi horizontal 2G dan 2F yang diusulkan dalam kegiatan pengabdian masyarakat pada tahun 2018 ini.
Pelatihan Ketrampilan Pengelasan untuk Keluarga Pra-Sejahtera di Sekitar Kampus ITS Surabaya Handayanu; Nur Syahroni; Yeyes Mulyadi; Imam Rochani; Kriyo Sambodho; M. Zikra; Rudi Walujo P; Yoyok Setyo H; Sholihin
Sewagati Vol 3 No 1 (2019)
Publisher : Pusat Publikasi ITS

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1118.653 KB)

Abstract

Jumlah keluarga pra-sejahtera pada dua kelurahan dekat ITS, yaitu Kelurahan Keputih dan Gebang Putih masih banyak, didapatkan fakta kuat bahwa faktor pengangguran menjadi faktor utamanya. ITS ingin ikut mengatasi masalah tersebut dengan memberikan pelatihan ketrampilan khusus kepada masyarakat di kedua kelurahan tersebut khusus untuk keluarga pra-sejahtera, sehingga bisa member ketrampilan yang memungkinkan pada lapangan pekerjaan yang sesuai dengan ketrampilan yang didapatkan dari pelatihan tersebut. Laboratorium Struktur, Material dan Produksi Bangunan Laut di Departemen Teknik Kelautan FTK-ITS memiliki peralatan pengelasan yang cukup lengkap, didukung dengan teknisi dan instruktur yang berpengalaman bisa dimanfaatkan untuk mendukung program pelatihan khususnya di bidang pengelasan tingkat dasar. Program pelatihan pengelasan tingkat dasar telah sukses dilakukan pada tahun 2015, 2016 dan 2017, dengan respon yang sangat positif dari para peserta yang mendapatkan manfaat langsung dari pelatihan ini. Tingkat ketrampilan yang didapatkan pada pelatihan pengelasan dasar meliputi, penyalaan busur, pengelasan posisi horizontal 1G dan 1F, keamanan, perlengakapan/pakaian dan perlindungan mata. Pelatihan pada tahun 2018 diikuti oleh 9 peserta. Sehingga total sejak angkatan pertama 2015 ada 38 peserta pelatihan yang telah mengikuti. Dari survey terakhir untuk angkatan 2016 dan 2017 dengan total peserta 17 orang, didapat informasi ada 4 orang (23,5%) yang mengalami perubahan pekerjaan terkait dengan dibidang pengelasan.