Claim Missing Document
Check
Articles

Found 5 Documents
Search
Journal : Journal of Sustainable Technology and Applied Science

RECOMMENDATIONS FOR IMPROVEMENT AND CONTROL MECHANISMS IN THE PRODUCTION PROCESS OF NOXONE 297 SL 1 LITER WITH FMEA APPROACH Setio, Hadi Rachmad; Julianus Hutabarat; Dimas Indra Laksmana
Journal of Sustainable Technology and Applied Science (JSTAS) Vol. 3 No. 2 (2022): Journal of Sustainable Technology and Applied Science, November 2022
Publisher : Lembaga Penelitian dan Pengabdian Masyarakat, Institut Teknologi Nasional (ITN) Malang

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.36040/jstas.v3i2.3873

Abstract

Product packaging is one of the critical factors in a product. The main problem with product packaging is the frequent occurrence of defects that exceed the company's targets and cause consumer disappointment. The purpose of this research is to minimise the occurrence of defects in product packaging so that recommendations for improvement and performance control mechanisms are needed. Improvement recommendations are made based on analysing the failure mode using the Pareto chart and FMEA (failure mode and effect analysis) tools. The results of this study are in the form of SOP recommendations for improvement and control mechanisms for 3 product packaging.
PRODUCT QUALITY CONTROL USING SIX SIGMA (DMAIC) METHODS TO MINIMIZE WAST IN BIMA MANDIRI CIGARETTE COMPANY REMBANG, PASURUAN REGENCY Husen, Muhammad; Gustopo, Dayal; Laksmana, Dimas Indra
Journal of Sustainable Technology and Applied Science (JSTAS) Vol. 2 No. 2 (2021): Journal of Sustainable Technology and Applied Science, November 2021
Publisher : Lembaga Penelitian dan Pengabdian Masyarakat, Institut Teknologi Nasional (ITN) Malang

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.36040/jstas.v2i2.3359

Abstract

Quality is a key to be able to compete in the industrial world [16. Quality control is needed to reduce the number of defective products produced by the company, thus reducing losses experienced by the company. The Bima Mandiri Rembang Pasuruan cigarette company is a company that produces cigarettes, one of which is INNO cigarettes. The number of defective products produced by the company so that the company must make an increase in quality by using a method to reduce the number of defects that occur. The number of defective products causes the company to suffer losses. For that, we need a method that can reduce cigarette defective products which in turn can improve the quality of the company's production[12]. Six Sigma with the DMAIC stage (Define, Measure, Analyze, Improve, Control) is a method used in this research. Based on these steps, defects that often occur are less dense cigarettes as many as 289 sticks with a percentage of 25%, tearing on the cigarettes as many as 227 cigarettes with a percentage of 20% and peeling cigarettes as many as 208 sticks with a percentage of 18%. Factors that cause defects include humans, machines, methods and materials. After calculating using the Six Sigma method, before the improvement, the DPMO value is 113988.1 and the Sigma Level value is 2.722. After the improvements were made, the DPMO value decreased to 76488.1 and the Sigma Level was 2.94715. To achieve the six sigma target, the company is expected to be able to carry out improvements with a focus on the factors that cause product defects and always carry out regular control to reduce product defects. The corrective steps taken in the Bima Mandiri Rembang Pasuruan Regency cigarette company are human: regular training for machine operators and employees; methods: inspection of raw materials, blending machines and glue residue in the teat; engine: inspection of engine components; material: reprocessing less refined raw materials and using better quality glue.
ANALYSIS OF MUSCULOSCKELETAL COMPLAINTS DISORDERED WITH REBA METHOD AND RULA METHOD : (CASE STUDY OF SMK BRANTAS KARANGKATES MALANG DISTRICT) Wargiono, Didik; Hutabarat, Julianus; Laksmana, Dimas Indra
Journal of Sustainable Technology and Applied Science (JSTAS) Vol. 2 No. 1 (2021): Journal of Sustainable Technology and Applied Science, May 2021
Publisher : Lembaga Penelitian dan Pengabdian Masyarakat, Institut Teknologi Nasional (ITN) Malang

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.36040/jstas.v2i1.3578

Abstract

Class furniture, namely tables and chairs, are significant physical facilities because the furniture is used for teaching and learning activities. Pain in the neck, waist, right upper arm, right forearm and right wrist during the learning process due to non-ergonomic facilities. Therefore, this research aims to minimize the complaints of Musculoskeletal Disorder with the Ergonomic Learning Chair. In this study, descriptive research with the REBA method and the RULA method was used. With the REBA method, the final score obtained in Group C is 8, then this value is entered at Action Level 3, after which researchers can only find out that the student's body posture level is in the High category so that action is needed immediately. With the RULA method, the student's body activity results are at a Group C score of 7. The value is entered for Action Level 4 so that the student's posture is in the dangerous category for safety, health and comfort. Therefore, action is needed now to overcome this problem with the suggestion manufacture of Ergonomic Study Chair. From the results of the chair use test design analysis by distributing questionnaires to 35 students as a sample, it was found that there was a decrease in complaints of Musculoskeletal Disorder in the student body. With the contribution of the study table, it can be adjusted up and down (adjustable) to make the chair more comfortable.
RISK ANALYSIS ON MSME TATTI CROCHET USING HOUSE OF RISK Ramadhani, Anisa Ramadhani; Achmadi, Fuad; Laksmana, Dimas Indra
Journal of Sustainable Technology and Applied Science (JSTAS) Vol. 3 No. 2 (2022): Journal of Sustainable Technology and Applied Science, November 2022
Publisher : Lembaga Penelitian dan Pengabdian Masyarakat, Institut Teknologi Nasional (ITN) Malang

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.36040/jstas.v3i2.4525

Abstract

Tatti Crochet is an MSME (Micro, Small, and Medium Enterprise) in Malang City engaged in the handicraft industry. The handicrafts produced are knitted goods, with a specialisation in knitting bags. As an MSME producing handicrafts, Tatti Crochet faces problems in human resources, especially knitters. The number of knitters currently available is three people, and this number cannot support the production needs of Tatti Crochet. This is one of the risks that must be faced not only by MSMEs but also by other organisations and companies. Risk management can be carried out by risk identification, evaluation and measurement, and risk management. One method that can be used to manage risk is the House of Risk. From the risk identification process, Tatti Crochet faced 22 risk events triggered by 29 agents. Based on the calculation of HOR Phase 1, 10 risk agents will enter HOR Phase 2 for determining preventive action, namely A11, A10, A18, A13, A14, A3, A12, A5, A28, and A4. Finally, one preventative measure was soon done with the highest ETD number, PA1, with ETD 1620.
AN ANALYSIS OF THE EFFECTS OF PERFORMANCE ON COMMUNITY SATISFACTION BASED ON CUSTOMER VOICE (CASE STUDY IN COOPERATIVE OFFICES, SMES, INDUSTRY AND TRADE, CENTRAL SUMBA DISTRICT) Sabakula, Abner Umbu Laiya; Achmadi, Fuad; Laksmana, Dimas Indra
Journal of Sustainable Technology and Applied Science (JSTAS) Vol. 4 No. 2 (2023): Journal of Sustainable Technology and Applied Science, November 2023
Publisher : Lembaga Penelitian dan Pengabdian Masyarakat, Institut Teknologi Nasional (ITN) Malang

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.36040/jstas.v4i2.6596

Abstract

To prepare civil servants who are professional, capable of competing, and capable of anticipating rapid world developments in various aspects of life, in order to improve service quality and awareness of the need for quality human resources, various strategies that can improve employee performance must be implemented. One strategy is to provide additional employee income as a form of motivation (TPP). The goal of this study is to assess community satisfaction with the performance of the Central Sumba Regency's cooperative, SME, industry, and trade departments using Voice of Customer data. The research method employs questionnaires to assess customer satisfaction with the PDCA approach, as well as service quality and IPA analysis. The findings of this study indicate that people are dissatisfied with the performance of employees and that changes must be made. The final results obtained after using the PDCA approach and analysis using servqual and Importance Performance Analysis (IPA) are performance factors that are priority improvements and performance that must be maintained in order to meet community satisfaction. Keywords: voice of costumer, PDCA, service quality, IPA