cover
Contact Name
-
Contact Email
-
Phone
-
Journal Mail Official
turbo@ojs.ummetro.ac.id
Editorial Address
Jl. Ki Hajar Dewantara No. 116 Kota Metro
Location
Kota metro,
Lampung
INDONESIA
Turbo : Jurnal Program Studi Teknik Mesin
ISSN : 23016663     EISSN : 2477250X     DOI : https://doi.org/10.24127
Core Subject : Engineering,
TURBO ISSN (print version) 2301-6663 & ISSN (online version) 2477-250X is a peer-reviewed journal that publishes scientific articles from the disciplines of mechanical engineering, which includes the field of study (peer) material, production and manufacturing, construction and energy conversion. Articles published in the journal Mechanical include results of original scientific research (original), and a scientific review article (review). Mechanical journal published by the Department of Mechanical Engineering, Faculty of Engineering, University Muhammadiyah of Metro for publishing two periods a year, in June and December with the number of articles 14-20 per year . Editors receive manuscripts in mechanical engineering from various academics, researchers and industry practitioners.
Articles 767 Documents
ANALISIS PENGARUH GEOMETRI SAMBUNGAN PIPA TERHADAP POLA ALIRAN DAN PRESSURE DROP PADA BYPASS HPH–DEAERATOR Pramiswara Fatikha, Vanya; Surahmanto, Fredy
TURBO [Tulisan Riset Berbasis Online] Vol 15 No 2 (2026): TURBO: Jurnal Program Studi Teknik Mesin (in Progress)
Publisher : Universitas Muhammadiyah Metro

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.24127/trb.v15i2.5423

Abstract

Pressure loss in the High Pressure Heater (HPH)–deaerator bypass pipeline reduces the hydraulic performance of the feedwater system. One of the factors affecting pressure loss is the geometry of the pipe junction. This study aims to investigate the effect of pipe junction geometry on flow characteristics and pressure drop in the HPH–deaerator bypass using three-dimensional Computational Fluid Dynamics (CFD). Unlike previous studies, which generally evaluated tee or elbow geometries separately, this study compares the existing blind tee with 1D, 1.5D, and 3D elbow configurations. Simulations were performed using ANSYS Fluent 2023 R2 under steady-state, single-phase flow conditions. The working fluid was modeled as compressed liquid water based on the HPH design specifications and temperature data obtained from the Distributed Control System (DCS). The simulation results show that the blind tee produced the most non-uniform velocity and pressure distributions, resulting in the highest pressure drop of 20,150 Pa. Replacing the blind tee with elbow configurations improved flow uniformity and reduced the pressure drop to 18,181 Pa, 18,322 Pa, and 18,161 Pa for the 1D, 1.5D, and 3D elbow configurations, respectively. The results indicate that the 3D elbow provides the most uniform flow characteristics and the lowest pressure drop, making it a promising alternative pipe junction geometry for the HPH–deaerator bypass system.
ANALISIS DESAIN IMPROVEMENT ROLLER ASSEMBLY PADA MESIN BUNDLING MENGGUNAKAN FINITE ELEMENT METHOD Nugroho Andri Kurniawan; Braam Delfian Prihadianto; Lilik Dwi Setyana; Handoko
TURBO [Tulisan Riset Berbasis Online] Vol 15 No 2 (2026): TURBO: Jurnal Program Studi Teknik Mesin (in Progress)
Publisher : Universitas Muhammadiyah Metro

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.24127/trb.v15i2.5454

Abstract

The roller assembly is a critical component in a bundling machine that functions to grip and guide materials during the packaging process. Based on operational data, the failure frequency reached 248 units for the nip roll and 124 units for the shaft, exceeding the monthly replacement standards of 160 units and 80 units, respectively. This condition indicates uneven load distribution, which reduces system reliability and increases maintenance costs. This study aims to analyze the stress, strain, deformation, and contact pressure distributions of the existing roller assembly design and evaluate the effect of geometric optimization on the safety factor and fatigue life of the components. The analysis was conducted using the Finite Element Method with ANSYS Mechanical software. The materials used were Polyurethane 80A for the nip roll, ASTM A36 steel for the bracket, and AISI 1045 steel for the shaft. Design improvements were implemented by increasing the nip roll diameter by 20%, enlarging the contact width between the nip roll and the motor roller by 87.5%, increasing the bracket thickness by 50%, and adding a 0.5 mm fillet radius to the bracket. The simulation results showed that the improved design reduced the equivalent stress by 31.2%, equivalent elastic strain by 25.3%, and total deformation by 0.98%. In addition, the fatigue life increased by approximately 431 times, while the safety factor improved by 79,5% compared to the existing design. These results demonstrate that geometric optimization is effective in enhancing the structural performance and reliability of the roller assembly.
Design and Analysis of a 5 m3 Excavator Bucket for Coal Handling Using Topology Optimization and Finite Elemen Analysis Hidayat, Farhan; Basuki, Budi; Santoso, Nugroho; Bekti Wibowo, Setyawan; Harjono
TURBO [Tulisan Riset Berbasis Online] Vol 15 No 2 (2026): TURBO: Jurnal Program Studi Teknik Mesin (in Progress)
Publisher : Universitas Muhammadiyah Metro

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.24127/trb.v15i2.5420

Abstract

Conventional excavator bucket designs frequently exhibit over-engineering, which reduces operational efficiency due to excessive structural mass. This study aims to optimize the PC500 bucket with a capacity of 5 m³ to reduce mass and evaluate fatigue. 3D modeling was performed using SolidWorks, while Finite Element Analysis (FEA) testing was simulated through Ansys Workbench. The load simulations applied the parameters of HARDOX 400 steel material. The topology optimization results successfully reduced the bucket mass by 10.65%, from 2,702.04 kg to 2,414.31 kg. The payload capacity also increased from 5 m³ to 5.2 m³. The FEA recorded a maximum von Mises stress of 256.71 MPa with a minimum safety factor of 3.895, ensuring structural safety. The fatigue evaluation proved that the design is safe from fatigue failure. The optimized bucket is proven to be lighter, more efficient, and has a larger capacity.
Pengaruh Perlakuan Alkali dan Fraksi Volume Terhadap Sifat Fisik dan Mekanik Komposit Berpenguat Serat Tandan Kosong Kelapa Sawit Hasibuan, Musdalifah; Hestiawan, Hendri; Zuliantoni; Alqap, A. Sofwan F; Gustriranda, Hairul
TURBO [Tulisan Riset Berbasis Online] Vol 15 No 2 (2026): TURBO: Jurnal Program Studi Teknik Mesin (in Progress)
Publisher : Universitas Muhammadiyah Metro

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.24127/trb.v15i2.5564

Abstract

Oil palm empty fruit bunch (OPEFB) fibers are promising as composite reinforcement because they are lightweight, widely available, environmentally friendly, and relatively low production costs. This study aimed to investigate the alkali treatment and volume fraction effects on the physical and mechanical properties of OPEFB fiber-reinforced composites. Reinforcement consisted of OPEFB fibers screened to 50 mesh, with polyester resin as the matrix and methyl ethyl ketone peroxide as the catalyst at a 100:1 resin-to-catalyst ratio. Fibers were alkali-treated using 4% NaOH for either 1 hour or 2 hours. Composites were fabricated with fiber volume fractions of 20% and 30%. An experimental program evaluated physical properties (density and water absorption) and mechanical properties (flexural strength and impact resistance). Results show that both fiber volume fraction and alkali treatment significantly affect the composites’ properties. The best performance was observed for the composite containing 20% fiber volume fraction treated with 4% NaOH for 2 hours, which achieved a flexural strength of 45.3 MPa and a water absorption of 0.65%.
Optimasi Ketebalan Isolator Glasswool pada Panci Listrik Mini Berbasis Simulasi Conjugate Heat Transfer dan Analisis Life Cycle Cost Alpihuda, Bakti; Akbar, Nizam Fikry; Hadiputranto, Rachmanto
TURBO [Tulisan Riset Berbasis Online] Vol 15 No 2 (2026): TURBO: Jurnal Program Studi Teknik Mesin (in Progress)
Publisher : Universitas Muhammadiyah Metro

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.24127/trb.v15i2.5572

Abstract

Mini domestic electric cookers are commonly sold without thermal insulation, resulting in avoidable heat loss. This study determines the glasswool insulation thickness that minimizes the life cycle cost of a Q2-8012 mini electric cooker by integrating Conjugate Heat Transfer (CHT) simulation with Life Cycle Cost (LCC) analysis. Simulations were run for five thickness configurations of 0, 5, 10, 15, and 20 mm in SolidWorks Flow Simulation using an external analysis approach, an inner wall temperature fixed at 95 °C, and natural convection computed directly from airflow physics. The heat loss data were regressed with a series-resistance model at a coefficient of determination of 0.9997, then optimized against an LCC function based on ISO 15686-5:2017 over a five-year period. Heat loss decreased from 23.192 W to 6.808 W, a 70.6% reduction, with an economically optimal thickness of 11.28 mm and a practical recommendation of 10 mm. Life cycle cost savings reached IDR 33,918 (61.8%) with a payback period of 0.40 year. The lid was identified as the primary barrier to insulation effectiveness, its contribution to total heat loss rising from 12.1% to 80.8% as wall insulation thickened, so thickening beyond the optimum yields negligible benefit.
A STUDI KOMPARATIF SIFAT MEKANIK LIMBAH PLASTIK HIGH DENTISY POLYETHYLENE (HDPE) DAN KAYU MAHONI MELALUI PENGUJIAN TARIK, BENDING, DAN TEKAN: STUDI KOMPARATIF SIFAT MEKANIK LIMBAH PLASTIK HIGH DENTISY POLYETHYLENE (HDPE) DAN KAYU MAHONI MELALUI PENGUJIAN TARIK, BENDING, DAN TEKAN Sukroni; Emin Haris; Yusup Nur Rohmat; Systi Adi Rachmawati; M Iqbal Saputra
TURBO [Tulisan Riset Berbasis Online] Vol 15 No 2 (2026): TURBO: Jurnal Program Studi Teknik Mesin (in Progress)
Publisher : Universitas Muhammadiyah Metro

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.24127/trb.v15i2.5590

Abstract

High-Density Polyethylene (HDPE) plastic waste has the potential to be repurposed as an alternative material, while mahogany wood is known for its favorable mechanical properties. This study aims to determine and compare the mechanical properties of recycled HDPE and mahogany wood through tensile, flexural, and compressive testing. An experimental method was employed, involving the fabrication of specimens from both recycled HDPE and mahogany wood. Tensile testing was conducted in accordance with ASTM D638, while flexural testing followed ASTM D790-02. The parameters analyzed included tensile strength, elongation, flexural strength, flexural strain, and maximum compressive stress. The results indicate that the average tensile strength of mahogany wood is 23.964 MPa, whereas that of HDPE is 12.241 MPa. The average maximum compressive stress is 1.693 MPa for mahogany wood and 1.315 MPa for HDPE. In the flexural tests, the average flexural strength of mahogany wood is 497.892 MPa, slightly higher than that of HDPE (493.705 MPa). HDPE exhibits an average elongation of 60.733%, which is higher than that of mahogany wood (14.857%). The findings demonstrate that mahogany wood possesses superior mechanical strength, whereas HDPE exhibits significantly greater elongation capabilities compared to mahogany wood.
Multi - Response Optimization of MRR and Surface Roughness in CNC Turning of S45C Steel Using Taguchi - GRA Andra Ardiansyah; Muhammad Subhan; Eko Yudo
TURBO [Tulisan Riset Berbasis Online] Vol 15 No 2 (2026): TURBO: Jurnal Program Studi Teknik Mesin (in Progress)
Publisher : Universitas Muhammadiyah Metro

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.24127/trb.v15i2.5609

Abstract

The CNC Turning machining process is one of the widely used manufacturing processes due to its ability to produce components with high tolerance and precision, one example being the stepped shaft. Surface roughness and Material Removal Rate (MRR) are two important parameters that determine the quality and productivity of the machining process, particularly for S45C steel, which is widely applied in machine components such as gears, shafts, and others. However, the simultaneous optimization of these two responses remains a challenge, as they exhibit conflicting characteristics. This study aimed to determine the optimal process parameters for CNC Turning of S45C steel using a CNMG 120408 insert, and to investigate the effect of process parameters (spindle speed, feed rate, and depth of cut) on MRR and surface roughness. The method used was the Taguchi method with an L9(3³) orthogonal array, combined with Grey Relational Analysis (GRA) to transform the multi-response problem into a single Grey Relational Grade (GRG) value. The results showed that the optimal parameter combination consisted of a spindle speed of 1528 RPM, a feed rate of 0.252 mm/rev, and a depth of cut of 0.15 mm, yielding a confirmation test GRG value of 0.8137, higher than the predicted value of 0.7018. Meanwhile, the most influential machining process parameter was depth of cut, contributing the largest proportion at 36.396%.

Filter by Year

2012 2026


Filter By Issues
All Issue Vol 15 No 2 (2026): TURBO: Jurnal Program Studi Teknik Mesin (in Progress) Vol 15 No 1 (2026): TURBO: Jurnal Program Studi Teknik Mesin Vol 14, No 2 (2025): TURBO: Jurnal Program Studi Teknik Mesin Vol 14 No 2 (2025): TURBO: Jurnal Program Studi Teknik Mesin Vol 14 No 1 (2025): TURBO : Jurnal Program Studi Teknik Mesin Vol 14, No 1 (2025): TURBO : Jurnal Program Studi Teknik Mesin Vol 13, No 2 (2024): TURBO: Jurnal Program Studi Teknik Mesin Vol 13, No 1 (2024): TURBO : Jurnal Program Studi Teknik Mesin Vol 12, No 2 (2023): TURBO: Jurnal Program Studi Teknik Mesin Vol 12 No 1 (2023): TURBO: Jurnal Program Studi Teknik Mesin Vol 12, No 1 (2023): Jurnal TURBO Vol 11, No 1 (2022): Jurnal TURBO Volume 11 Nomor 1 Juni 2022 Vol 11, No 2 (2022): TURBO : Jurnal Program Studi Teknik Mesin Vol 11 No 2 (2022): TURBO : Jurnal Program Studi Teknik Mesin Vol 11 No 1 (2022): TURBO: Jurnal Program Studi Teknik Mesin Vol 10, No 1 (2021): Jurnal TURBO Juni 2021 Vol 10, No 2 (2021): Jurnal TURBO Vol 10 No 2 (2021): TURBO: Jurnal Program Studi Teknik Mesin Vol 9, No 2 (2020): Jurnal Turbo Desember 2020 Vol 9, No 1 (2020): Jurnal TURBO Vol 8, No 2 (2019): Jurnal Turbo Desember 2019 Vol 8, No 1 (2019): Juni 2019 Vol 7, No 2 (2018): Desember 2018 Vol 7 No 1 (2018): Juni 2018 Vol 7, No 1 (2018): Juni 2018 Vol 6, No 2 (2017): Desember 2017 Vol 6 No 2 (2017): Desember 2017 Vol 6, No 1 (2017): Juni 2017 Vol 5, No 2 (2016): Desember 2016 Vol 5, No 1 (2016): Juni 2016 Vol 4 No 2 (2015): Desember 2015 Vol 4, No 2 (2015): Desember 2015 Vol 4, No 1 (2015): Juni 2015 Vol 4 No 1 (2015): Juni 2015 Vol 4, No 1 (2015): Juni 2015 Vol 3, No 2 (2014): Desember 2014 Vol 3 No 2 (2014): Desember 2014 Vol 3 No 1 (2014): Juni 2014 Vol 3, No 1 (2014): Juni 2014 Vol 2, No 2 (2013): Desember 2013 Vol 2, No 2 (2013): Desember 2013 Vol 2 No 2 (2013): Desember 2013 Vol 2, No 1 (2013): Juni 2013 Vol 2, No 1 (2013): Juni 2013 Vol 2 No 1 (2013): Juni 2013 Vol 1, No 2 (2012): Desember 2012 Vol 1 No 2 (2012): Desember 2012 Vol 1, No 1 (2012): Juni 2012 More Issue