cover
Contact Name
-
Contact Email
-
Phone
-
Journal Mail Official
-
Editorial Address
-
Location
,
INDONESIA
Civil Engineering Journal
Published by C.E.J Publishing Group
ISSN : 24763055     EISSN : 24763055     DOI : -
Core Subject : Engineering,
Civil Engineering Journal is a multidisciplinary, an open-access, internationally double-blind peer -reviewed journal concerned with all aspects of civil engineering, which include but are not necessarily restricted to: Building Materials and Structures, Coastal and Harbor Engineering, Constructions Technology, Constructions Management, Road and Bridge Engineering, Renovation of Buildings, Earthquake Engineering, Environmental Engineering, Geotechnical Engineering, Highway Engineering, Hydraulic and Hydraulic Structures, Structural Engineering, Surveying and Geo-Spatial Engineering, Transportation Engineering, Tunnel Engineering, Urban Engineering and Economy, Water Resources Engineering, Urban Drainage.
Arjuna Subject : -
Articles 2,041 Documents
Probabilistic CPT-Based Liquefaction Hazard Assessment Using Monte Carlo Simulation Muhamad Yusa; Ilham Wirmansyah; Muhammad Kusairi; Soewignyo Agus Nugroho
Civil Engineering Journal Vol. 12 No. 9 (2026): September
Publisher : Salehan Institute of Higher Education

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.28991/CEJ-2026-012-09-05

Abstract

The common liquefaction assessment used in Indonesian practice does not include uncertainty in soil and earthquake parameters. This study aims to quantify liquefaction hazard risk in Indonesia by integrating the Idriss-Boulanger method with Monte Carlo Simulation (MCS) to account for uncertainties. Two distinct case studies in Indonesia were analyzed: an evaluation of the 2009 Padang earthquake and a prediction for the Universitas Riau campus development. Methods involved modeling stochastic variables, including cone resistance, sleeve friction, groundwater level, total vertical soil stress, earthquake moment magnitude, and peak ground acceleration, to calculate the probability of liquefaction (PL) across various iterations. Findings reveal that at the evaluation site, 74% of tested depths showed PL exceeding 65%, indicating a significant probability. This finding aligns with field-observed sand boils and settlement. In contrast, the prediction site showed predominantly PL between 15% and 35%; thus, costly ground improvement is unnecessary. This research found that cone resistance had the most significant influence on PL. Utilizing six stochastic variables, the minimum required number of iterations is 600,000. This research improves upon the traditional deterministic method widely used in Indonesian practice by providing a more reliable, non-conservative quantitative framework to decide whether ground improvement, as liquefaction mitigation, is required.
Valorization of Rice Husk–Derived Lignin as Bio-Admixture in Sustainable Mortar Remigildus Cornelis; Syahrul R. Hasan; Elia Hunggurami; Debora Lau; Alvin A. Bara; Henricus Priyosulistyo
Civil Engineering Journal Vol. 12 No. 9 (2026): September
Publisher : Salehan Institute of Higher Education

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.28991/CEJ-2026-012-09-08

Abstract

Rice husk-derived lignin (RHL) is a promising bio-admixture capable of supporting sustainable mortar production while improving agricultural waste use. Therefore, this study aimed to investigate the influence of non-sulfonated RHL on mortar workability, setting behavior, compressive strength, crack pattern, and microstructural characteristics at different dosage levels. RHL was extracted from rice husk through alkaline-acid precipitation without combustion treatment and incorporated into mortar mixtures at dosages of 0–0.5% by cement weight. Setting time, mortar flow, compressive strength, and crack behavior were evaluated at curing ages of 7, 14, and 28 days, supported by SEM–EDX, XRD, and FTIR analyses. The results showed that low to moderate RHL dosages improved mortar flow, accelerated setting behavior, and increased compressive strength. The optimum dosage of approximately 0.3% produced the highest 28-day compressive strength of 48.64 MPa, corresponding to an increase of about 15.8% compared with normal mortar. Crack pattern observations showed less severe surface fragmentation and more localized cracking in lignin-modified mortar. SEM–EDX, XRD, and FTIR analyses also suggested improved matrix compactness and more homogeneous hydration product development at the optimum dosage. However, excessive RHL incorporation reduced compressive strength despite continued improvements in flowability. These results showed that RHL could function effectively as a non-sulfonated bio-based mortar admixture without requiring combustion-based processing.
Microstructural and Geotechnical Evaluation of Cement-Stabilized Crude Oil-Contaminated Silty Clay Haqi H. Abbood; Mohammed K. Hatem; Hasan Ali Abbas; Nabil Al-Hakeem; Solomon Rubay; Mohammed Ali Hussein; Albert Prokopov
Civil Engineering Journal Vol. 12 No. 9 (2026): September
Publisher : Salehan Institute of Higher Education

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.28991/CEJ-2026-012-09-015

Abstract

This study assessed the performance of Ordinary Portland Cement (OPC) in stabilizing crude oil-contaminated silty clay soil with special focus on the improvement of the geotechnical and microstructural properties. Geotechnical tests were conducted on soil samples contaminated with crude oil at concentrations up to 20% and stabilized with cement contents from 6% to 10%. The geotechnical properties investigated were void ratio, compressibility, California Bearing Ratio (CBR) and unconfined compressive strength (UCS). Furthermore, Scanning Electron Microscopy (SEM) was used to characterize the microstructure changes in the soil. The results indicated that crude oil increased the initial void ratio and compression index by 18.3% and 47.6%, respectively, and decreased the CBR by 43.1% and soil cohesion by 40%, mainly due to the lubricating effect of oil on soil particles. The addition of OPC as a stabilizing binder promoted pozzolanic reactions, which resulted in an 11–24% reduction in void ratio under an applied stress of 710 kN/m2 and a 7.7–21.5-fold increase in UCS compared with the untreated contaminated soil. SEM analysis of the soil with 10% cement showed the formation of continuous C–S–H matrices around the oil droplets, and hydraulic conductivity was decreased by about 1.5 times. The results showed that the application of OPC can significantly improve the mechanical stability and microstructure of oil-contaminated silty clay, and therefore confirm the feasibility of using it as a soil stabilizer for environmental rehabilitation.
PIML Model to Predict the Behavior of Axially Loaded Large Piles During Conceptual Design Stage Ahmed M. Ebid; Kennedy C. Onyelowe; Laila A. Elkadi; Karim Sherif Mostafa; Norbaya Sidek; Mohamed A. Hafez
Civil Engineering Journal Vol. 12 No. 9 (2026): September
Publisher : Salehan Institute of Higher Education

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.28991/CEJ-2026-012-09-013

Abstract

The reliable prediction of axial load-settlement behavior of large-diameter drilled shafts during the conceptual design stage remains a challenging task in geotechnical engineering, primarily due to the limited availability of detailed site-specific parameters. This study introduces a novel application of physics-informed machine learning (PIML) techniques to estimate the hyperbolic coefficients (a & b) governing the load-settlement response of drilled shafts under axial compression, utilizing only basic soil classification data and pile dimensions as inputs. The primary objective is to develop robust, yet practically parsimonious, predictive models suitable for early-stage project design, thereby reducing dependency on extensive and costly site investigations. To achieve this, three machine learning algorithms—evolutionary polynomial regression (EPR), artificial neural networks (ANN), and genetic programming (GP)—were implemented and rigorously trained and validated using a database of 82 vertical pile load tests derived from the Cairo monorail project. A conventional linear regression (LNR) model was employed as a benchmark for comparative performance evaluation. The results demonstrate that the EPR and ANN models substantially outperform both GP and LNR approaches, achieving prediction accuracies of up to 93% and 85% for coefficients (a & b), respectively. Notably, the EPR model exhibited excellent performance with an R² of 0.975 and RMSE of 1.15 for coefficient (a), while the ANN model achieved an R² of 0.915 and RMSE of 0.7 for coefficient (b), underscoring the efficacy of PIML in capturing complex load-transfer mechanisms from minimal input data.
Investigation of Reinforced Concrete Slabs Strengthened with Shear-Connected Mesh Jacketing Omar Magdy; Januarti J. Ekaputri; Mahmoud Hegazy; Ahmed Youssef
Civil Engineering Journal Vol. 12 No. 9 (2026): September
Publisher : Salehan Institute of Higher Education

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.28991/CEJ-2026-012-09-020

Abstract

This study investigates the effectiveness of an integrated repair technique for corroded reinforced concrete (RC) slabs using mechanical surface preparation, steel dowels, supplementary reinforcement mesh, and shotcrete jacketing. Six standard-scale RC slab specimens were tested under static two-point loading: one uncorroded control slab (S01); two corroded unrepaired slabs with steel mass losses of 10.6% (S03) and 16.2% (S02); two repaired slabs at the same corrosion levels (S06 and S05); and one uncorroded slab strengthened with compression-zone jacketing (S04). The results showed that corrosion reduced the peak load by about 14% and resulted in losses in stiffness and ductility. In contrast, the proposed repair technique not only restored the original capacity but also increased the peak load by 71–75% compared with the control slab. Although the repaired specimens exhibited higher initial stiffness, they reached their maximum load at smaller deflections, indicating reduced ductility. Compression-zone strengthening improved the peak load by 30% and enhanced post-peak behavior. No interface debonding was observed, demonstrating effective composite action, and confirming the suitability of the proposed system for rehabilitating corrosion-damaged RC slabs.
Comparative Nonlinear Seismic Response of Fixed-Base and Lead-Rubber-Isolated Reinforced Concrete Building Systems Ali Kifah Kadhum; Mohammed Abid Jameel; Mohammed A. Radi; Zuhair Abd Hacheem
Civil Engineering Journal Vol. 12 No. 9 (2026): September
Publisher : Salehan Institute of Higher Education

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.28991/CEJ-2026-012-09-012

Abstract

This study examines how lead-rubber bearing (LRB) isolation changes the seismic response of a ten-story reinforced-concrete building using matched fixed-base and isolated models. Three-dimensional ETABS models were analyzed using nonlinear direct integration under the EQ-X component of the 1999 Kocaeli earthquake recorded at the Arcelik station. Nonlinear behavior was confined to 38 LRB links, while the superstructure remained linear elastic. Record import, units, scaling, spectrum screening, gravity initialization, damping, convergence, and signed response envelopes were verified. The results show that isolation lengthened the first period from 1.332 to 2.245 s and reduced the base-shear envelope from 9,066.91 to 5,778.71 kN, representing a reduction ratio of 36.3%. Story-shear reductions ranged from approximately 36.0% to 49.2%. Drift reductions from Stories 2 to 10 reached 47.6%, although the Story 1 superstructure drift increased by 96.9%. Matched absolute accelerations decreased by 52.6%, 38.6%, and 48.6% at Stories 1, 5, and 10, respectively, while the corrected center-of-mass overturning envelope decreased by 28.6%. The governing bearing displacement was 59.35 mm, corresponding to 39.6% of its 150 mm design value. The novelty and improvement of this work lie in its separation of bearing deformation from interstory drift, removal of the gravity offset from the overturning moment, comparison of matched absolute accelerations, and connection of the system response to a transparent bearing-level check.
Reliability-Based Assessment of Ballast Bearing Capacity Under Aggregate Degradation in Railway Tracks Mohammed Ashiru; Zhihong Nie; Aliyu Ibrahim; Zesizwe Ngubane; Jacob Adedayo Adedeji; Nura Shehu Aliyu Yaro
Civil Engineering Journal Vol. 12 No. 9 (2026): September
Publisher : Salehan Institute of Higher Education

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.28991/CEJ-2026-012-09-018

Abstract

The long-term performance and safety of ballasted railway tracks are significantly influenced by ballast degradation, which occurs under repeated train axle loads and results in diminished particle angularity, eroded surface texture, increased fines content, and reduced bearing capacity. This study assesses the effects of ballast degradation on bearing capacity using a reliability-based design framework that explicitly accounts for material and loading uncertainties. Experimental investigations comprised Los Angeles abrasion tests to quantify particle degradation using Marsal's breakage ratio and large-scale direct shear tests conducted under simulated axle loads of 20, 25, and 30 tonnes (equivalent contact stresses of 192, 240, and 288 kPa) to determine changes in shear strength parameters. Stochastic models of key design variables were developed from experimental data, and a limit equilibrium performance function was formulated, defining resistance as ballast-bearing capacity and load as the stress at the ballast–sleeper interface. Reliability analysis was conducted using the first-order reliability method (FORM) to estimate reliability indices and failure probabilities. The results show that increasing ballast degradation and axle loads significantly reduce shear strength and reliability and increase failure probability, particularly under 25- and 30-tonne loads. The study integrates laboratory-derived degradation indices with probabilistic reliability analysis, providing a practical approach for incorporating uncertainty into ballast design, maintenance planning, and railway safety management while extending track service life.
A Hybrid Data-Driven and Physics-Based Approach for Shear Capacity Estimation of Steel Fiber Reinforced Concrete Beams Fadhil A. Jasim; Ansam Z. Thamer; Hayder Kadhem Adai AL-Farttoosi; Tufail Mabood
Civil Engineering Journal Vol. 12 No. 9 (2026): September
Publisher : Salehan Institute of Higher Education

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.28991/CEJ-2026-012-09-04

Abstract

Estimation of shear strength of steel fiber reinforced concrete (SFRC) beams is difficult because of the complex nonlinear interactions between fiber, geometry, and reinforcements. In this study, the hybrid machine learning (ML) and finite element analysis (FEA) method are utilized for estimating the load-carrying capacity (Pmax) of SFRC beams. A database of 257 SFRC beams was collected from literature and was pre-processed. Seven ML methods, including Decision Tree, AdaBoost, Linear Regression, k-Nearest Neighbors, Random Forest, Stochastic Gradient Descent, and Gradient Boosting, were applied on the database through the k-fold cross-validation technique. The best model was selected as Gradient Boosting due to R² > 0.93. By conducting SHAP analysis, longitudinal reinforcement ratio, height of the beam, and shear span-to-depth ratio were found to be the most important parameters. Using nonlinear FEA in Abaqus, the results of ML models were validated by comparing them with experimental and simulation results (∆ ≈ 4.79% and ∆ ≈ 0.14%, respectively). Through parametric studies, the positive influence of the volume fraction of fibers and reinforcement ratio and negative influence of shear span-to-depth ratio were determined. The suggested ML-FEA approach can be considered accurate and efficient for practical SFRC shear design.
Interpretable Machine Learning for Landfill Cost Estimation Using XGBoost and SHAP Endah Murtiana Sari; Probokusumo; Muhamad Dzaky Ashidqi; Tezara Cionita; Agus Taufik Mulyono
Civil Engineering Journal Vol. 12 No. 9 (2026): September
Publisher : Salehan Institute of Higher Education

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.28991/CEJ-2026-012-09-017

Abstract

Accurate landfill cost estimation is essential for effective infrastructure planning and sustainable waste management, yet conventional approaches often fail to capture the complex nonlinear interactions among engineering, environmental, economic, and logistical factors. This study aims to develop an interpretable machine learning model for landfill cost estimation using Extreme Gradient Boosting (XGBoost) integrated with SHapley Additive exPlanations (SHAP). The analysis was conducted using data from 31 landfill projects in Indonesia collected from authorized contractors with government approval. The dataset includes remaining landfill capacity, leachate treatment cost, waste density, landfill tax, retaining wall height, and transportation distance. Data preprocessing involved unit standardization, normalization, and logarithmic transformation, followed by model training and evaluation using cross-validation, MAE, RMSE, and MAPE metrics. The results show that XGBoost outperforms Random Forest, achieving lower prediction errors and a MAPE below 1%, indicating high predictive accuracy. Residual analysis confirms that the model is generally unbiased, while feature importance and SHAP analyses identify leachate treatment cost, landfill tax, and retaining wall height as the dominant cost drivers. The novelty of this study lies in integrating explainable artificial intelligence with landfill cost estimation, providing both accurate predictions and transparent decision support for landfill planning and policy development.
Damage-Sensitive Mechanical and Transport Properties of Concrete Under Cryogenic Exposure Akkadath Abdulmatin; Penpichcha K. Sanit-in; Pitchayut Sanguthai; Sutep Sachdav; Suban Sanit-in; Weerachart Tangchirapat; Chai Jaturapitakkul; Chanachai Thongchom
Civil Engineering Journal Vol. 12 No. 9 (2026): September
Publisher : Salehan Institute of Higher Education

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.28991/CEJ-2026-012-09-09

Abstract

This study investigates the residual performance of concrete after repeated cryogenic thermal shock and evaluates how water-to-binder (W/B) ratio, binder content, and fly ash replacement influence damage development. Seven concrete mixtures were tested at 28 days after up to three 1-hour liquid-nitrogen immersion cycles. Compressive strength, elastic modulus, reinforcing-bar bond strength and slip, length change, void content, and water permeability were examined to characterize load-bearing capacity, stiffness, interfacial behavior, deformation, and transport integrity. After three cycles, the control mixture retained 84% of its initial compressive strength but only 46% of its elastic modulus, demonstrating that stiffness was more sensitive to accumulated internal damage. First-cycle compressive-strength retention ranged from 65% to 99%, with mixtures having lower W/B ratio and higher binder content generally showing better retention. Bond strength decreased more modestly, whereas length-change records revealed rapid expansion during immersion and residual deformation after recovery. Void content increased after exposure, and measurable permeability generally increased, indicating development of connected transport paths; values unavailable after cracking were reported as N/A. The combined results show that elastic modulus, deformation, and transport properties complement compressive strength in assessing cryogenic damage and support performance-based selection of concrete mixtures for LNG-related structures.

Filter by Year

2015 2026


Filter By Issues
All Issue Vol. 12 No. 10 (2026): October Vol. 12 No. 9 (2026): September Vol. 12 No. 8 (2026): August Vol. 12 No. 5 (2026): May Vol. 12 No. 4 (2026): April Vol. 12 No. 3 (2026): March Vol. 12 No. 2 (2026): February Vol. 12 No. 1 (2026): January Vol. 11 No. 12 (2025): December Vol. 11 No. 11 (2025): November Vol. 11 No. 10 (2025): October Vol. 11 No. 9 (2025): September Vol. 11 No. 8 (2025): August Vol. 11 No. 7 (2025): July Vol. 11 No. 6 (2025): June Vol. 11 No. 5 (2025): May Vol. 11 No. 3 (2025): March Vol 11, No 3 (2025): March Vol 11, No 2 (2025): February Vol. 11 No. 2 (2025): February Vol 11, No 1 (2025): January Vol 10, No 12 (2024): December Vol 10, No 11 (2024): November Vol. 10 No. 11 (2024): November Vol 10, No 10 (2024): October Vol 10, No 9 (2024): September Vol 10, No 8 (2024): August Vol. 10 No. 7 (2024): July Vol 10, No 7 (2024): July Vol 10, No 6 (2024): June Vol 10, No 5 (2024): May Vol. 10 No. 5 (2024): May Vol 10, No 4 (2024): April Vol 10, No 3 (2024): March Vol 10, No 2 (2024): February Vol 10, No 1 (2024): January Vol 10 (2024): Special Issue "Sustainable Infrastructure and Structural Engineering: Innovations in Vol 9, No 12 (2023): December Vol 9, No 11 (2023): November Vol 9, No 10 (2023): October Vol 9, No 9 (2023): September Vol 9, No 8 (2023): August Vol 9, No 7 (2023): July Vol 9, No 6 (2023): June Vol 9, No 5 (2023): May Vol 9, No 4 (2023): April Vol 9, No 3 (2023): March Vol 9, No 2 (2023): February Vol 9, No 1 (2023): January Vol 9 (2023): Special Issue "Innovative Strategies in Civil Engineering Grand Challenges" Vol 8, No 12 (2022): December Vol 8, No 11 (2022): November Vol 8, No 10 (2022): October Vol 8, No 9 (2022): September Vol 8, No 8 (2022): August Vol 8, No 7 (2022): July Vol 8, No 6 (2022): June Vol 8, No 5 (2022): May Vol 8, No 4 (2022): April Vol 8, No 3 (2022): March Vol 8, No 2 (2022): February Vol 8, No 1 (2022): January Vol 7, No 12 (2021): December Vol 7, No 11 (2021): November Vol 7, No 10 (2021): October Vol 7, No 9 (2021): September Vol 7, No 8 (2021): August Vol 7, No 7 (2021): July Vol 7, No 6 (2021): June Vol 7, No 5 (2021): May Vol 7, No 4 (2021): April Vol 7, No 3 (2021): March Vol 7, No 2 (2021): February Vol 7, No 1 (2021): January Vol 7 (2021): Special Issue "Innovative Strategies in Civil Engineering Grand Challenges" Vol 6, No 12 (2020): December Vol 6, No 11 (2020): November Vol 6, No 10 (2020): October Vol 6, No 9 (2020): September Vol 6, No 8 (2020): August Vol 6, No 7 (2020): July Vol 6, No 6 (2020): June Vol 6, No 5 (2020): May Vol 6, No 4 (2020): April Vol 6, No 3 (2020): March Vol 6, No 2 (2020): February Vol 6, No 1 (2020): January Vol 6 (2020): Special Issue "Emerging Materials in Civil Engineering" Vol 5, No 12 (2019): December Vol 5, No 11 (2019): November Vol 5, No 10 (2019): October Vol 5, No 9 (2019): September Vol 5, No 8 (2019): August Vol 5, No 7 (2019): July Vol 5, No 6 (2019): June Vol 5, No 6 (2019): June Vol 5, No 5 (2019): May Vol 5, No 4 (2019): April Vol 5, No 4 (2019): April Vol 5, No 3 (2019): March Vol 5, No 3 (2019): March Vol 5, No 2 (2019): February Vol 5, No 2 (2019): February Vol 5, No 1 (2019): January Vol 5, No 1 (2019): January Vol 4, No 12 (2018): December Vol 4, No 12 (2018): December Vol 4, No 11 (2018): November Vol 4, No 11 (2018): November Vol 4, No 10 (2018): October Vol 4, No 10 (2018): October Vol 4, No 9 (2018): September Vol 4, No 9 (2018): September Vol 4, No 8 (2018): August Vol 4, No 8 (2018): August Vol 4, No 7 (2018): July Vol 4, No 7 (2018): July Vol 4, No 6 (2018): June Vol 4, No 6 (2018): June Vol 4, No 5 (2018): May Vol 4, No 5 (2018): May Vol 4, No 4 (2018): April Vol 4, No 4 (2018): April Vol 4, No 3 (2018): March Vol 4, No 3 (2018): March Vol 4, No 2 (2018): February Vol 4, No 2 (2018): February Vol 4, No 1 (2018): January Vol 4, No 1 (2018): January Vol 3, No 12 (2017): December Vol 3, No 12 (2017): December Vol 3, No 11 (2017): November Vol 3, No 11 (2017): November Vol 3, No 10 (2017): October Vol 3, No 10 (2017): October Vol 3, No 9 (2017): September Vol 3, No 9 (2017): September Vol 3, No 8 (2017): August Vol 3, No 7 (2017): July Vol 3, No 7 (2017): July Vol 3, No 6 (2017): June Vol 3, No 5 (2017): May Vol 3, No 5 (2017): May Vol 3, No 4 (2017): April Vol 3, No 3 (2017): March Vol 3, No 2 (2017): February Vol 3, No 2 (2017): February Vol 3, No 1 (2017): January Vol 2, No 12 (2016): December Vol 2, No 12 (2016): December Vol 2, No 11 (2016): November Vol 2, No 11 (2016): November Vol 2, No 10 (2016): October Vol 2, No 9 (2016): September Vol 2, No 9 (2016): September Vol 2, No 8 (2016): August Vol 2, No 8 (2016): August Vol 2, No 7 (2016): July Vol 2, No 7 (2016): July Vol 2, No 6 (2016): June Vol 2, No 6 (2016): June Vol 2, No 5 (2016): May Vol 2, No 4 (2016): April Vol 2, No 3 (2016): March Vol 2, No 3 (2016): March Vol 2, No 2 (2016): February Vol 2, No 1 (2016): January Vol 1, No 2 (2015): December Vol 1, No 1 (2015): November More Issue