Garuda - Garba Rujukan Digital

All

Reaktor

reaktor
Website

Published by Universitas Diponegoro

ISSN : 08520798 EISSN : 24075973 DOI : https://doi.org/10.14710/reaktor.xx.x.xx-xx

Chemical Engineering, Chemistry & Bioengineering Control & Systems Engineering Energy Materials Science & Nanotechnology

Reaktor invites contributions of original and novel fundamental research. Reaktor publishes scientific study/ research papers, industrial problem solving related to Chemical Engineering field as well as review papers. The journal presents paper dealing with the topic related to Chemical Engineering including: Transport Phenomena and Chemical Engineering Operating Unit Chemical Reaction Technique, Chemical Kinetics, and Catalysis Designing, Modeling, and Process Optimization Energy and Conversion Technology Thermodynamics Process System Engineering and products Particulate and emulsion technologies Membrane Technology Material Development Food Technology and Bioprocess Waste Treatment Technology

Arjuna Subject : Teknik (semua kategori) - Teknik (Lain-Lain)

Articles 530 Documents

41 42 43 44 45

The Effects of Operational Conditions in Scaling Up of Xylanase Enzyme Production for Xylitol Production Diah Meilany; Dewinka Anugeraheni; Abdul Aziz; Made Tri Ari Penia Kresnowati; Tjandra Setiadi
Reaktor Volume 20 No.1 March 2020
Publisher : Dept. of Chemical Engineering, Diponegoro University

The biological route to produce xylitol from Oil Palm Empty Fruit Bunches (EFBs) comprises of EFBs pretreatment, enzymatic hydrolysis, fermentation, and downstream separation of the produced xylitol. Due to the specificity in the hemicellulose composition of EFBs, a xylanase enzyme that has a high affinity to EFBs is required to hydrolyze the EFBs into xylose. In this research, the influences of aeration, humidity, and mixing in xylanase production were mapped. The xylanase production was performed by Aspergillus fumigatus ITBCCL170 in a solid-state fermentation using a tray fermenter with EFBs as the substrate. The optimal configuration was further scaled up into xylanase production using 1000 g of EFBs as the substrate. The results showed that the highest enzyme activity was 236.3 U/g EFB, obtained from the use of humid air airflow of 0.1 LPM, and mixing was performed once a day. The scaling up resulted in a lower xylanase activity and call for a better design of the fermenter.Keywords: aeration, humidity, mixing, OPEFBs, tray fermenter, xylanase, xylitol

Characterization of Antimicrobial Edible Films with Single and Double Emulsions from Clove (Syzygium aromaticum) Oil Kam Natania; Giovani Fransisca Setiawan
Reaktor Volume 20 No.1 March 2020
Publisher : Dept. of Chemical Engineering, Diponegoro University

Clove oil as a potent antimicrobial agent was added to enhance the properties of edible films. Clove oil was converted to single and double emulsion emulsions for homogenous dispersion in a starch based edible film suspension. Double emulsion was made with two steps emulsification with CaCl2 as inner water phase and guar gum as outer water phase. Single emulsion was prepared similarly without inner water phase. The physico-chemical characteristics and the antimicrobial activity of the of starch-based edible film added with the emulsion were observed. MBC/MFC of clove oil was determined against E. coli, S. aureus, R. stolonifer, and A. niger which gives value of 1.95, 1.46, 0.52, and 0.35 mg/ml respectively. Incorporation of different emulsions on starch-based edible films affect the properties of resulting edible films by increasing thickness, opacity, elongation at break, water vapor transmission rate, and swelling index. Both emulsions showed comparable physicochemical characteristics such as thickness, WVTR, and swelling index value. However, double emulsion produced more superior edible films in terms of tensile strength and antimicrobial activity. 15% addition of double emulsion were able to show strong antimicrobial activity with inhibition zone of more than 8.0 mm for E. coli and 24.0 mm for R. stolonifer.Keywords: clove oil; edible film; single and double emulsion

Kinetics of Enzymatic Hydrolysis of Passion Fruit Peel using Cellulase in Bio-ethanol Production Megawati Megawati; Astrilia Damayanti; Radenrara Putri; Angga Pratama; Tsani Muftidar
Reaktor Volume 20 No.1 March 2020
Publisher : Dept. of Chemical Engineering, Diponegoro University

This research aims to study the hydrolysis of passion fruit peel using cellulase and its evaluation for ethanol production. Passion fruit peel is a fruit processing waste that has not been utilized properly. Passion fruit peel contains holo-cellulose (64% w/w), which can be converted into ethanol through hydrolysis followed by fermentation. Hydrolysis using cellulase is more efficient and its fermentation using yeast to produce ethanol is common. The hydrolysis is carried out at various enzyme ratios (3, 5, 7, and 9% v/v) and at temperature 30 oC, material concentration 5 g/100 mL, pH 4-5, and shaking speed 160 rpm. The kinetics chosen were heterogeneous models; they were the fractal model by Valjamae and Kopelman. Before being hydrolyzed, the essential oil and pectin in passion fruit peel were extracted, because the compositions were quite high; the results were around 16.23 and 11.36% w/w, respectively. The effect of the enzyme ratio to the sugar concentration by hydrolysis is very significant. At 9 h, the glucose concentration reached 45.38, 51.86, 60.50, 66.00 g/L at various enzyme ratios of 3, 5, 7, 9% v/v. During the hydrolysis, the glucose concentration continues to increase and starts to decrease after 9 h. Hydrolyzate solution fermentation obtained from hydrolysis in various enzyme ratios showed consistent results; the higher the enzyme ratio and glucose, and the higher the ethanol will be (5.6, 6.8, 7.6, and 8.9% v/v). The kinetics model by Valjamae is more appropriate to describe the enzymatic hydrolysis mechanism of passion fruit peel than Kopelman. The fractal exponent values obtained from Valjamae and Kopelman models were 0.28 and 0.27. In Valjamae model, the enzyme ratio rises, from 3 to 9% v/v, the rate constant rises from 0.22 to 0.53 1/h. In Kopelman model, the rate constant rises too, from 0.21 to 0.51 1/h.Keywords: bio-ethanol; cellulase; enzymatic hydrolysis; fractal kinetic; passion fruit peel

Optimization of Bio-oil Production from Empty Palm Fruit Bunches by Pyrolysis using Response Surface Methodology Tutuk Djoko Kusworo; Bayu Aji Pratama; Dhea Putri Safira
Reaktor Volume 20 No.1 March 2020
Publisher : Dept. of Chemical Engineering, Diponegoro University

The need for fuel oil continues to increase in line with the increasing number of human populations and the growth rate of dependence on fuel oil. Bio-oil is a condensed-liquid mixture that results from the thermal derivation of biomass containing hemicellulose, lignin, and cellulose. This research developed an optimization of the operation condition of bio-oil from empty palm fruit bunches (OPEFB) using a modified pyrolysis reactor. The temperature and mass of empty palm fruit bunches were the two parameters considered in this study. Optimization was carried out on process parameters using the surface response methodology (RSM) and variance analysis (ANOVA). The significance of the different parameters and the effect of the relationship between parameters on the bio-oil yield is determined using a full factorial central composite design. The optimal operation condition of pyrolysis was found to be 570.71 oC, and the mass of empty palm fruit bunch 420.71 gr. Predictions from the optimum variable of operating conditions produce a bio-oil yield of 5.58%. The actual bio-oil yield on the optimum condition that was be validated is 5.6 %. The chemical composition of bio-oil obtained was evaluated by GCMS to ensure its characterization as a fuel.Keywords: Empty palm fruit bunches, Bio-oil, Pyrolysis, Response Surface Methodology, Optimization

Application of Square and Oblong Pore Shapes in Rotating Membrane Emulsification to Produce Novel Particulate Products Nita Aryanti; Richard Andrew Williams; Qinchung Yuan
Reaktor Volume 20 No.1 March 2020
Publisher : Dept. of Chemical Engineering, Diponegoro University

Rotating membrane emulsification (RMR) has been intensively developed and applied for producing emulsion as well as particulate products such as microcapsules. Polyurea microcapsules were generally prepared by interfacial polycondensation polymerisation with addition of modifier to produce more stable microcapsules. In this research, development of the RMR was applied for producing polymer particles stabilised by nanoparticle without any addition of surfactant or modifier. Two types of membrane pores, the square (Type-A) with hydraulic diameter (Dh) of 84 mm and oblong pores with an aspect ratio of 0.33 (Type-B) having Dh of 69 mm was investigated. For the membranes designed in this research, pore shape A membrane could produce good uniformity in both polyurea microcapsule and polymer particle. In the polymer stabilised particle, this membrane type obtained a narrower size distribution than the usage for o/w emulsification. Reasonable uniform particles at high membrane rotation speed could also be achieved with the use of Type-A membrane. The uniformity confirmed that there was only minor breakup of products during operation at high membrane rotation. This attractive feature was significant in the production of fragile or shear-sensitive particulate products since the delicate structure of these products is possibly easy to destroy at high membrane rotation speed. Keywords: polyurea microcapsules; particles stabilised nanoparticles; slotted pore

Antioxidant Properties of Different Types of Torbangun Herbal Tea Intan Cidarbulan Matita; Titri Siratantri Mastuti; Smita Maitri
Reaktor Volume 20 No.1 March 2020
Publisher : Dept. of Chemical Engineering, Diponegoro University

In this study, Torbangun leaves are processed into three different types varying in their oxidation degree, namely unoxidized, semioxidized and oxidized Torbangun leaves. Each type is then brewed into herbal tea and analyzed in terms of its total phenolic, total flavonoid and antioxidant activity. Unoxidized Torbangun herbal tea shows higher content of total phenolic (44.22 mg GAE/g) and total flavonoid (17.02 mg QE/g) compared to oxidized (24.66 mg GAE/g total phenolic content and 8.61 mg QE/g total flavonoid content) and semioxidized (33.83 mg GAE/g total phenolic content and 10.68 mg QE/g total flavonoid content) Torbangun herbal tea. In terms of the antioxidant activity, processing the Torbangun leaves into herbal tea tremendously decreased the antioxidant activity based on the IC50 value of 1400.89 ɥg/mL for unoxidized Torbangun herbal tea, 3211.71 ɥg/mL for semioxidized Torbangun herbal tea and 4504.78 ɥg/mL for oxidized Torbangun herbal tea. However, steam blanching used in the preparation of unoxidized Torbangun leaves is proven to increase the total phenolic and flavonoid content of raw or unprocessed Torbangun leaves from 39.02 to 44.22 mg GAE/g and an increase of total flavonoid from 10.32 to 17.02 mg QE/g.Keywords: antioxidant; flavonoid; herbal tea; phenolic; torbangun

Application of the Fenton Process in the Petroleum Refinery Spent Caustic Wastewater Treatment Riang Anggraini Rahmanisa; I Nyoman Widiasa
Reaktor Volume 20 No.2 June 2020
Publisher : Dept. of Chemical Engineering, Diponegoro University

Spent caustic wastewater is produced from the scrubbing process using a caustic solution to absorb contaminants in the oil stream (hydrocarbon). Indonesia’s Petroleum Oil Refinery produces spent caustic wastewater from LPG and kerosene processing unit. Spent caustic wastewater has the characteristic of a strong odor with very high pH (12-14), containing dangerous pollutants such as phenol, aldehydes, mercaptans, and thiols that can be harmful to the human and environment. The Fenton process is used to treat spent caustic before being discharged to the environment. The Fenton process is one of AOPs (Advanced Oxidation Process) using Fe2+ as a catalyst and H2O2 as an oxidant to oxidize organic contaminants in wastewater. This study aims to determine the operating conditions of the Fenton Process with the target characteristics of treated spent caustic meet the WWTP (Waste Water Treatment Plant) inlet specifications and to make the design process of spent caustic treatment with the Fenton Process capacity of 10 m3/day. By operating at the H2O2/Fe (II) ratio of 1.8, the final target was achieved with COD of 810 ppm, ammonia of 22.84 ppm, sulfide of 60.93 ppm and phenol of 14.56 ppm. Total Capital Investment (TCI) for the design is US$ 2146701.89 whereas Total Manufacturing Cost of US$ 2089740.75.Keywords: spent caustic; refinery wastewater; Fenton process

Application of the Fenton Process in the Petroleum Refinery Spent Caustic Wastewater Treatment Rahmanisa, Riang Anggraini; Widiasa, I Nyoman
Reaktor Volume 20 No.2 June 2020
Publisher : Dept. of Chemical Engineering, Diponegoro University

Spent caustic wastewater is produced from the scrubbing process using a caustic solution to absorb contaminants in the oil stream (hydrocarbon). Indonesiaâ€™s Petroleum Oil Refinery produces spent caustic wastewater from LPG and kerosene processing unit. Spent caustic wastewater has the characteristic of a strong odor with very high pH (12-14), containing dangerous pollutants such as phenol, aldehydes, mercaptans, and thiols that can be harmful to the human and environment. The Fenton process is used to treat spent caustic before being discharged to the environment. The Fenton process is one of AOPs (Advanced Oxidation Process) using Fe2+ as a catalyst and H2O2 as an oxidant to oxidize organic contaminants in wastewater. This study aims to determine the operating conditions of the Fenton Process with the target characteristics of treated spent caustic meet the WWTP (Waste Water Treatment Plant) inlet specifications and to make the design process of spent caustic treatment with the Fenton Process capacity of 10 m3/day. By operating at the H2O2/Fe (II) ratio of 1.8, the final target was achieved with COD of 810 ppm, ammonia of 22.84 ppm, sulfide of 60.93 ppm and phenol of 14.56 ppm. Total Capital Investment (TCI) for the design is US$ 2146701.89 whereas Total Manufacturing Cost of US$ 2089740.75.Keywords: spent caustic; refinery wastewater; Fenton process

Effect of Ethanol Addition as Extraction Solvent on The Content of Bioactive Materials in Dragon Fruit Skin Extract and Powder Dian Shofinita; Yasid Bindar; Tjokorde Walmiki Samadhi; Arwinda Aprillia Jaelawijaya; Mifta Fawwaz
Reaktor Volume 20 No.2 June 2020
Publisher : Dept. of Chemical Engineering, Diponegoro University

This study aims to produce natural pigments for food prepared from dragon fruit skin by extraction and freeze-drying and to assess the effect of additional ethanol as extraction solvent on the process yield. During extraction stage, the effect of solvent (pure water and additional ethanol) on the yield of bioactive materials was assessed. Furthermore, during freeze-drying, the effect of maltodextrin addition as carrier agent on the quality of powder has also been evaluated. It has been found that the addition of ethanol as extraction co-solvent may give a positive effect on the yield of bioactive materials in the dragon fruit skin extracts, including the contents of anthocyanin, betacyanin, and total phenolic compounds. Regarding freeze drying, it was found that high recoveries of bioactive materials (84-92%) had been achieved, which indicates that freeze-drying may be suitable for drying such heat-sensitive materials. In addition, it was found that the addition of 10% maltodextrin as carrier agent may decrease the moisture content of the powder significantly, up to 8.162.12%, which is beneficial for its storage stability.Keywords: betacyanin; food additives; dragon fruit; extraction; anthocyanin.

Effect of Ethanol Addition as Extraction Solvent on The Content of Bioactive Materials in Dragon Fruit Skin Extract and Powder Shofinita, Dian; Bindar, Yasid; Samadhi, Tjokorde Walmiki; Jaelawijaya, Arwinda Aprillia; Fawwaz, Mifta
Reaktor Volume 20 No.2 June 2020
Publisher : Dept. of Chemical Engineering, Diponegoro University

This study aims to produce natural pigments for food prepared from dragon fruit skin by extraction and freeze-drying and to assess the effect of additional ethanol as extraction solvent on the process yield. During extraction stage, the effect of solvent (pure water and additional ethanol) on the yield of bioactive materials was assessed. Furthermore, during freeze-drying, the effect of maltodextrin addition as carrier agent on the quality of powder has also been evaluated. It has been found that the addition of ethanol as extraction co-solvent may give a positive effect on the yield of bioactive materials in the dragon fruit skin extracts, including the contents of anthocyanin, betacyanin, and total phenolic compounds. Regarding freeze drying, it was found that high recoveries of bioactive materials (84-92%) had been achieved, which indicates that freeze-drying may be suitable for drying such heat-sensitive materials. In addition, it was found that the addition of 10% maltodextrin as carrier agent may decrease the moisture content of the powder significantly, up to 8.16ï‚±2.12%, which is beneficial for its storage stability.Keywords: betacyanin; food additives; dragon fruit; extraction; anthocyanin.

Page 43 of 53 | Total Record : 530

41 42 43 44 45

Filter by Year

1999 2025

Filter By Issues

All Issue Volume 25 No.2 August 2025 Volume 25 No.1 April 2025 Volume 24 No.3 December 2024 Volume 24 No.2 August 2024 Volume 24 No.1 April 2024 Volume 23 No.3 December 2023 Volume 23 No.2 August 2023 Volume 23 No.1 April 2023 Volume 22 No. 3 December 2022 Volume 22 No.2 August 2022 Volume 22 No. 1 April 2022 Volume 21 No.4 December 2021 Volume 21 No. 3 September 2021 Volume 21 No. 2 June 2021 Volume 21 No. 1 March 2021 Volume 20 No.4 December 2020 Volume 20 No.3 September 2020 Volume 20 No.2 June 2020 Volume 20 No.1 March 2020 Volume 19 No. 4 December 2019 Volume 19 No. 3 September 2019 Volume 19 No. 2 June 2019 Volume 19 No. 1 March 2019 Volume 18 No. 4 December 2018 Volume 18 No. 3 September 2018 Volume 18 No. 2 June 2018 Volume 18 No. 1 March 2018 Volume 17 No. 4 Desember 2017 Volume 17 No. 3 September 2017 Volume 17 No. 2 Juni 2017 Volume 17 No.1 Maret 2017 Volume 16 No.4 Desember 2016 Volume 16 No.3 September 2016 Volume 16 No. 2 Juni 2016 Volume 16 No.1 Maret 2016 Volume 15 No.4 Oktober 2015 Volume 15 No.3 April 2015 Volume 15, No.2, OKTOBER 2014 Volume 15, No.1, APRIL 2014 Volume 14, No. 4, OKTOBER 2013 Volume 14, No. 3, APRIL 2013 Volume 14, Nomor 2, Oktober 2012 Volume 14, Nomor 1, April 2012 Volume 13, Nomor 4, Desember 2011 Volume 13, Nomor 3, Juni 2011 Volume 13, Nomor 2, Desember 2010 Volume 13, Nomor 1, Juni 2010 Volume 12, Nomor 4, Desember 2009 Volume 12, Nomor 3, Juni 2009 Volume 12, Nomor 2, Desember 2008 Volume 12, Nomor 1, Juni 2008 Volume 11, Nomor 2, Desember 2007 Volume 11, Nomor 1, Juni 2007 Volume 10, Nomor 2, Desember 2006 Volume 10 No. 1 Juni 2006 Volume 09 No. 02 Desember 2005 Volume 09 No.1 Juni 2005 Volume 08 No.2 Desember 2004 Volume 08 No.1 Juni 2004 Volume 07 No.2 Desember 2003 Volume 07 No. 1 Juni 2003 Volume 6 No. 2 Desember 2002 Volume 6 No. 1 Juni 2002 Volume 5 No.2 Desember 2001 Volume 5 No. 1 Juni 2001 Volume 3 No.1 Desember 1999 More Issue

Home Page

OAI Link

Editorial Team

Contact

Reviewer

Google Scholar

Contact Name
Dessy Ariyanti

Contact Email
dessy.ariyanti@che.undip.ac.id

Phone
+62247460058

Journal Mail Official
j.reaktor@che.undip.ac.id

Editorial Address
Department of Chemical Engineering, Diponegoro University Jl. Prof. Soedarto SH Tembalang Semarang 50275

Location
Kota semarang,

Jawa tengah

INDONESIA

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Home Page

OAI Link

Editorial Team

Contact

Reviewer

Google Scholar

Contact Name Dessy Ariyanti

Contact Email dessy.ariyanti@che.undip.ac.id

Phone +62247460058

Journal Mail Official j.reaktor@che.undip.ac.id

Editorial Address Department of Chemical Engineering, Diponegoro University Jl. Prof. Soedarto SH Tembalang Semarang 50275

Location Kota semarang, Jawa tengah INDONESIA

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Contact Name
Dessy Ariyanti

Contact Email
dessy.ariyanti@che.undip.ac.id

Phone
+62247460058

Journal Mail Official
j.reaktor@che.undip.ac.id

Editorial Address
Department of Chemical Engineering, Diponegoro University Jl. Prof. Soedarto SH Tembalang Semarang 50275

Location
Kota semarang,

Jawa tengah

INDONESIA