cover
Contact Name
-
Contact Email
-
Phone
-
Journal Mail Official
-
Editorial Address
-
Location
Kota adm. jakarta selatan,
Dki jakarta
INDONESIA
Metalurgi
ISSN : 01263188     EISSN : 24433926     DOI : -
Core Subject : Science,
METALURGI published by Research Center for Metallurgy and Materials LIPI. The objective of this journal is the online media for disseminating of RCMM results in Research and Development and also as a media for a scientist and researcher in the field of Metallurgy and Materials.
Arjuna Subject : -
Articles 240 Documents
PENGARUH PENCAMPURAN DAN RASIO PREKURSOR/DOPAN DALAM PEMBUATAN LAPISAN TIPIS FLUORINE DOPED TIN OXIDE (FTO) BERBASIS TIMAH (II) KLORIDA[The Effect of Mixing Condition and Dopant/Precursor Ratio in Fabrication of Fluorine Doped Tin Oxide (FTO) Thin Film Based on Tin (II) Chloride] Lalasari, Latifa Hanum
Metalurgi Vol 30, No 3 (2015): Metalurgi Vol. 30 No. 3 Desember 2015
Publisher : Pusat Penelitian Metalurgi dan Material - LIPI

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1164.299 KB) | DOI: 10.14203/metalurgi.v30i3.68

Abstract

Flourine-doped tin oxide (FTO) merupakan salah satu oksida yang umum digunakan dalam pelapisan pada kaca yang diberi perlakuan tertentu agar dapat menghantarkan listrik. FTO ini diharapkan dapat menggantikan fungsi indium tin oxide (ITO) yang  bahan bakunya sangat mahal dan tersedia dalam jumlah yang terbatas. Percobaan pendahuluan tentang pembuatan lapisan tipis F-SnO2 dilakukan menggunakan kombinasi metode sol gel dan dip coating. Percobaan ini menggunakan bahan baku timah (II) klorida hidrat (SnCl2.2H2O) sebagai prekursor dan ammonium florida (NH4F) sebagai doping. Hasil percobaan menunjukkan bahwa lamanya waktu pencampuran antar prekursor dan doping tidak begitu  mempengaruhi kestabilan larutan. Faktor yang signifikan mempengaruhi adalah kondisi pencampuran antara prekursor dan doping. yang terkontrol. Lapisan tipis SnO2 yang dihasilkan dalam percobaan ini mempunyai morfologi heksagonal tidak teratur dan fasa Sn4OF6. AbstractFluorine-doped tin oxide (FTO) is an oxide that is commonly used in the coating on the glass treated aparticular treatment in order to be able to conduct electricity. FTO is expected to replace indium tin oxide(ITO) whose raw materials are very expensive and available in limited quantities. Preliminary experimentson the manufacture of F-SnO2 thin film done with using combinations of sol gel method and dip coating.This experiment used the raw material of tin (II) chloride hydrate (SnCl2.2H2O) as precursors and ammoniumfluoride (NH4F) as doping. The results showed that the processing time between the mixing of precursors anddoping was not so affect the stability of the solution. The significant factor affecting was the concentrationratio of the dopant/precursor and the conditions of mixing between the precursors and doping. Theconcentration ratio of the dopant/precursors of 10% produced the most stable conductive solution(US-1-½-½) with a thin layer of FTO has generated more regular hexagonal morphology, uniform and phaseof Sn4OF6.
Pengaruh Penambahan Inhibitor Ekstrak Tembakau Terhadap Laju Korosi Internal Pipa API 5L X-52 Pada Artificial Brine Water Dengan Injeksi Gas CO2 [Effect of Addition of Extracted Tobacco Inhibitor to The Corrosion Rate of Internal Steel Pipe API 5L X-52 in Artificial Brine Water With CO2 Gas Injection] Ahmadi, Rapli Nur; Oediyani, Soesaptri; Priyotomo, Gadang
Metalurgi Vol 31, No 3 (2016): Metalurgi Vol. 31 No. 3 Desember 2016
Publisher : Pusat Penelitian Metalurgi dan Material - LIPI

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (827.178 KB) | DOI: 10.14203/metalurgi.v31i3.164

Abstract

Crude oil containing brine water with high concentration of NaCl and HCO3 and the presence of dissolved CO2 gas may increase the potential for corrosion in the pipeline. The use of natural corrosion inhibitor is one of the alternative to solve these problem. Natural materials were chosen as an alternative because it is safe, readily available, biodegradable, low cost, and environmentally friendly. This study was conducted to determine the effect of tobacco extracts on the rate of corrosion and inhibition efficiency. The novelty of this research is a continuous injection of CO2 gas that does not exist in previous research. Spectroscopy analysis was conducted to determine the chemical composition of samples of steel API 5L X-52, TLC densitometry was used to determine the levels of nicotine in tobacco sauce. Gamry Potensiostat Type 6:25 was used for testing the corrosion behavior, using the Tafel polarization and EIS methods. The results show that, the corrosion rate of samples decreased with the addition of tobacco extracts. The addition of 60 ppm of tobacco extract in a solution decrease corrosion rate samples at 8.95 mpy in ABW 1 and 9.87 mpy in ABW 2. Optimum inhibition efficiency occurs upon the addition of 60 ppm tobacco extracts, for the solution of ABW 1 by 79.51% and amounted to 80.94% ABW 2. The inhibition efficiency began to decline by the addition of 80 ppm, to 42.32% in ABW 1 by and 68.71% in ABW 2.AbstrakCrude oil yang mengandung brine water dengan kadar NaCl dan HCO3 - yang tinggi serta adanya gas CO2 yang terlarut dapat meningkatkan potensi korosi pada pipa. Penggunaan inhibitor korosi alami menjadi alternatif baru untuk menyelesaikan masalah tersebut. Bahan alam dipilih sebagai alternatif karena bersifat aman, mudah didapatkan, bersifat biodegradable, biaya murah, dan ramah lingkungan. Penelitian ini dilakukan untuk mengetahui pengaruh penambahan ekstrak tembakau terhadap laju korosi dan efisiensi inhibisi yang dihasilkan dengan menambahkan pembaharuan penelitian berupa penginjeksian gas CO2 secara kontinu yang belum ada pada penelitian sebelumnya. Pengujian pada penelitian ini menggunakan spectroscopy untuk mengetahui komposisi kimia sampel baja API 5L X-52, TLC. Densitometri digunakan untuk mengetahui kadar nikotin pada sampel tembakau. Gamry Potensiostat Type 6.25 digunakan untuk pengujian polarisasi Tafel dan EIS. Hasil penelitian menunjukkan bahwa data laju korosi baja API 5L X-52 mengalami penurunan dengan penambahan ekstrak tembakau. Penurunan optimum laju korosi terjadi pada penambahan 60 ppm ekstrak tembakau pada larutan ABW 1 sebesar 8,95 mpy dan ABW 2 sebesar 9,87 mpy. Peningkatan optimum efisiensi inhibisi terjadi pada penambahan 60 ppm ekstrak tembakau, untuk larutan ABW 1 sebesar 79,51% dan ABW 2 sebesar 80,94%. Efisiensi inhibisi mulai mengalami penurunan kembali pada penambahan 80 ppm, untuk larutan ABW 1 sebesar 42,32% dan ABW 2 sebesar 68,71%. 
Metoda FZ pada Pembuatan Kristal Tunggal La O 2-2x Sr 1+2x Mn 2 7 Imaduddin, Agung
Metalurgi Vol 26, No 1 (2011): Metalurgi Vol. 26 No. 1 April 2011
Publisher : Pusat Penelitian Metalurgi dan Material - LIPI

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (262.416 KB) | DOI: 10.14203/metalurgi.v26i1.1

Abstract

 La2-2xSr1+2xMn2O7 (x=0,4) mempunyai CMR (Colossal Magnetoresistance) terbesar dibandingkan bahan Mn oxide lainnya[1]. Untuk menyelidiki sifat CMR ini, kita harus dapat membuat kristal tunggalnya. Untuk itu kami telah membuat kristal tunggal La2-2xSr1+2xMn2O(x=0,4) atau disebut LSMO 327. Kristal tunggal kami buat dengan metoda FZ (Floating Zone). Sebelum pembuatan kristal tunggal dengan 7 memakai metoda FZ, kami telah menganalisa hubungan suhu dan konsentrasi x dengan memakai thermocouple dan analisaEPMA (Electron Probe Microanalysis).Setelah penumbuhan dengan memakai metoda FZ, analisa struktur kristal dan sifat kristalisasinya pada hasil kristal tunggalnya dilakukan denga memakai XRD dan rocking curve, kemudian kami juga memakai EPMA untuk mengetahui komposisi unsur yang terbentuk. Dari hasil metoda FZ ini diketahui bahwa permukaan cleave (permukaan kelupas)  nya adalah bidang ab, dan memiliki nilai half full value width nya 0,115° , yang menunjukkan kualitas kristal tunggal yang tinggi. Dari EPMA diketahui bahwa nilai x pada La2-2x Sr 1+2x Mn2O7 adalah 0,409. AbstractLa2-2xSr1+2xMn2O7 (x=0.4) has the most large CMR (Colossal Magnetoresistance)[1]. In order to research on CMR effect, we have to prepare high quality single crystals. We have grown La2-2xSr1+2xMn2O7 single crystal of x = 0.4 (or LSMO 327). We have grown single crystals with FZ (Floating Zone) method. Before growing single crystals using the FZ method, we have analyzed the relation of temperature and concentration x by using thermo-couple and analysis of EPMA (Electron Probe Microanalysis). After growing using the FZ method, analysis of crystal structure and its crystallization properties were carried out using XRD and Rocking curve, then we were also using EPMA to determine its elemental composition. From the results of the FZ method, we know that the cleaved surface is the ab plane, and has a half full value width of 0.115° , which indicates a high quality single crystal. From the EPMA result, we know that the value of x at the LA2-2xSr1 +2 xMn2O7 is 0.409.
Analisis Fasa Sistem Mn₍₁₋ₓ₎NdxFe2O4 Sebagai Kandidat Bahan Penyerap Gelombang Mikro Yunasfi, Yunasfi -; Rachmawati, Indri; Mashadi, Mashadi; Adi, Wisnu Ari; Arofah, Nurmaya
Metalurgi Vol 33, No 2 (2018): Metalurgi Vol. 33 No. 2 Agustus 2018
Publisher : Pusat Penelitian Metalurgi dan Material - LIPI

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (581.775 KB) | DOI: 10.14203/metalurgi.v33i2.428

Abstract

Telah dilakukan analisis fasa sistem Mn(1-x)NdxFe2O4 sebagai bahan penyerap gelombang mikro hasil sintesis dengan metode sol-gel. Sistem Mn(1-x)NdxFe2O4 (dengan x = 0,0; 0,1 dan 0,2) disintesis dengan mencampurkan serbuk Fe(NO3)3, Mn(NO3)3 dan Nd(NO3)3 sesuai dengan perbandingan molnya. Campuran bahan ini dilarutkan dengan etilen glikol, dikeringkan dengan oven pada suhu 120 °C dan kemudian disinter pada 1200 °C selama 3 jam. Identifikasi fasa menggunakan XRD (X-ray diffractometer) menunjukkan terbentuknya multifasa yang ditandai dengan munculnya fasa MnFe2O3 dan FeNdO3. Pengamatan morfologi dengan SEM menunjukkan terbentuknya struktur yang tidak homogen untuk seluruh sampel dengan ukuran sekitar 200-400 nm. Serapan gelombang mikro yang diukur dengan VNA (Vector Network Analyzer) menunjukkan bahwa substitusi  ion Nd3+ dapat meningkatkan kemampuan material menyerap gelombang mikro, dengan serapan terbesar ~93% oleh komposisi x = 0,2 (Mn0,8Nd0.2Fe2O4).
SIFAT MEKANIK DAN STRUKTUR MIKRO PELAT TIPIS Zn HASIL ROL DINGIN UNTUK APLIKASI ANODA KORBAN Saefudin, Saefudin; Senopati, Galih
Metalurgi Vol 29, No 2 (2014): Metalurgi Vol.29 No.2 Agustus 2014
Publisher : Pusat Penelitian Metalurgi dan Material - LIPI

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (623.306 KB) | DOI: 10.14203/metalurgi.v29i2.279

Abstract

SIFAT MEKANIK DAN STRUKTUR MIKRO PELAT TIPIS Zn HASIL ROL DINGIN UNTUKAPLIKASI ANODA KORBAN. Proteksi katodik dengan anoda korban banyak digunakan untuk melindungistruktur logam dari korosi pada lingkungan air laut. Proses pembuatan anoda korban Zn tersebut dapat dilakukanmelalui proses pengecoran yang dilanjutkan dengan proses rol dingin (cold rolling). Tujuan penelitian ini adalahuntuk mendapatkan pelat tipis Zn sebagai bahan baku anoda korban yang bebas cacat pada skala laboratorium.Pelat Zn hasil cor dan rol dingin dengan ketebalan 1 mm kemudian diuji keras menggunakan alat uji vicker’s danSEM-EDS (scanning electron microscopy-energy dispersive spectroscopy). Harga kekerasan tertinggi dari pelatZn dengan tebal 1 mm adalah rata-rata 95,63 VHN. Tingginya kekerasan pelat Zn dipengaruhi oleh adanyapartikel ZnFeAl yang menghasilkan sifat getas dalam material tersebut.
Proses Reduksi Selektif Bijih Nikel Limonit Menggunakan Zat Aditif CaSO4 [Selective Reduction Process of Nickel Limonite With Adictive CaSO4] Mayangsari, Wahyu; Prasetyo, Agus Budi
Metalurgi Vol 31, No 1 (2016): Metalurgi Vol. 31 No. 1 April 2016
Publisher : Pusat Penelitian Metalurgi dan Material - LIPI

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1007.727 KB) | DOI: 10.14203/metalurgi.v31i1.86

Abstract

This research aims to determine the optimum selective reduction conditions process of limonite nickel ore using additives CaSO4 and followed by magnetic separation to improve the nickel content. The selective reduction process was carried out at temperature range of 800 – 1100 °C, 1-4 h of reduction time, and the addition of the reducing agent and additives 5% - 20%. Limonite nickel ore was prepared by heating the ore inside the oven, size reduction and sieving to get ore with size under 100 mesh. Then, limonite nickel ore was mixed with reducing agent and additive. In addition, the limonite nickel ore which was mixed with the reducing agent and additive, was reduced in muffle furnace carbolite at certain temperature and time. Reduction result was weighed and concentrated by magnetic separation process, and the result was analysedby AAS (atomic absorption spectrometry) to determine of Ni contents in concentrates. The results showed that the higher a reduction temperature, Ni content and metallization of Ni was improved with the formation of Ni metal which separated from the Fe metal. The similar result was found with longer of reduction time. On the contrary, the higher an addition of reducing agent in the reduction mixture, the Ni content decreased slightly. The addition of CaSO4 can increasing the nickle content but it was not given the tendency for the good results. The highest increasing of nickel contents i.e. 2,44% was achieved at 1100 ºC of reduction temperature, 1 h of reduction time, 10% addition of reducing agent and 20% addition of CaSO4 additive. The recommended reduction temperature are 1100 °C for 1 h of reduction time, with 10% addition of reducing agent and 20% addition of CaSO4 additive.AbstrakPenelitian ini bertujuan untuk mengetahui kondisi optimum pada proses reduksi selektif bijih nikel limonit menggunakan zat aditif CaSO4 dan diikuti dengan pemisahan magnetik untuk mendapatkan peningkatan kadar nikel. Proses reduksi selektif dilakukan pada rentang suhu 800 - 1100 °C, waktu reduksi 1 – 4 jam, serta penambahan reduktor dan aditif 5% - 20%. Preparasi bijih nikel limonit dilakukan dengan pemanasan bijih dalam oven, pengecilan ukuran dan pengayakan untuk mendapatkan bijih dengan ukuran lolos 100 mesh. Kemudian dilakukan pencampuran bijih nikel limonit dengan reduktor dan aditif. Campuran bijih nikel limonit kemudian direduksi dalam muffle furnace carbolite pada suhu dan waktu tertentu. Hasil reduksi kemudian ditimbang dan dikonsentrasikan menggunakan proses pemisahan magnetik dan hasilnya dianalisis dengan metode AAS (atomic absorption spectrometry) untuk mengetahui kadar Ni pada konsentrat. Hasil penelitian menunjukkan bahwa semakin tinggi suhu reduksi, peningkatan kadar Ni dan metalisasi logam Ni semakin tinggi, dengan terbentuknya logam Ni yang terpisah dari logam Fe. Hal yang sama juga terjadi jika waktu reduksi semakin lama. Namun, semakin banyak penambahan reduktor pada campuran reduksi, peningkatan kadar Ni semakin kecil. Penambahan CaSO4 dapat meningkatkan kadar nikel namun belum memberikan kecenderungan hasil yang baik. Peningkatan kadar Ni tertinggi yang didapatkan adalah 2,44%. Direkomendasikan untuk menggunakan suhu reduksi 1100 °C, waktu reduksi 1 jam, penambahan reduktor 10% dan penambahan aditif CaSO4 20%.
indeks, panduan Jurnal Metalurgi, Redaksi
Metalurgi Vol 26, No 3 (2011): Metalurgi Vol. 26 No. 3 Desember 2011
Publisher : Pusat Penelitian Metalurgi dan Material - LIPI

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.14203/metalurgi.v26i3.385

Abstract

INVESTIGASI EKSPERIMENTAL PERILAKU PROFIL BAJA RINGAN BERPENAMPANG PERSEGI AKIBAT INTERAKSI BEBAN TEKAN MEMUSAT DAN MOMEN LENTUR[Behaviour Experimental Investigation of A Thin-Walled Steel Square Hollow Secton Beam Affected by the Interaction of Concentrated Compressive Load and Bending Moment] Kadir, Andi Muhdiar; Priadi, Dedi; Siradj, Eddy S; Setiyono, Harkali
Metalurgi Vol 28, No 1 (2013): Metalurgi Vol.28 No.1 April 2013
Publisher : Pusat Penelitian Metalurgi dan Material - LIPI

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (886.257 KB) | DOI: 10.14203/metalurgi.v28i1.244

Abstract

INVESTIGASI EKSPERIMENTAL PERILAKU PROFIL BAJA RINGAN BERPENAMPANGPERSEGI AKIBAT INTERAKSI BEBAN TEKAN MEMUSAT DAN MOMEN LENTUR. Makalah inimerupakan bagian dari program penelitian yang di fokuskan pada pengembangan metode analisa kekuatan profilbaja berdinding tipis berbentuk pipa kotak (Square Hollow Section/SHS) akibat interaksi beban tekan memusatdan momen lentur yang didasarkan pada pendekatan teori mekanisme plastis dan elastis (plastic mechanisms andelastic theories/cut-off strength) dimana tingkat akurasinya akan diverifikasi menggunakan hasil pendekatanexperimental. Pada tahap pertama penelitian ini, analisa kekuatan SHS didasarkan pada desain standar yang adayaitu British Standard (BS 5950 Part 5 1987) yang menggunakan metode langsung (direct method) dan metodedua kanal (double channels method). Pada metode eksperimental dilakukan pengujian awal yaitu pengujianmaterial dasar dari SHS dan pengujian utama yaitu pengujian kekuatan profil baja berdinding tipis berbentukpipa kotak akibat interaksi beban tekan memusat dan momen lentur. Data hasil uji material dasar digunakansebagai data masukan pada analisis kekuatan profil baja berdinding tipis berbentuk pipa kotak menggunakanBritish Standard sedangkan hasil uji kekuatan profil baja berdinding tipis berbentuk pipa kotak dijadikan sebagaiacuan dari metode analisis kekuatan yang digunakan. Hasil analisa kekuatan SHS menunjukkan bahwa hasilanalisa kekuatan dengan metode double channels memberikan hasil yang mendekati hasil experimental(perbedaan sekitar 2 % sampai 7%) dibandingkan dengan metode lansung dan hal ini masih dalam batas-batasyang dapat diterima (acceptable limits) „b 20 %. Hasil pada tahap awal berupa hasil eksperimental dan hasilanalisis kekuatan menggunakan standard desain cukup akurat dan akan digunakan sebagai pembanding denganhasil dari metode analisa kekuatan yang dikembangkan pada tahap penelitian selanjutnya. AbstractThis paper is a part of research program that focused in developing a strength analytical method of a thinwalledsteel square pipe (Square Hollow Section/SHS) affected by the interaction of concentratedcompressiveload and bending moment that its based on plastic mechanisms and elastic theories (cut-offstrength), and its accuracy will then be verified by data obtain from an experimental approach. In the firststage of this research program, the strength of SHS pipe is analyzed by using of existing code design namelyBritish Standard (BS 5950 Part 5 1987) that is implemented according to a direct method and doublechannels one. In the experimental method is performing preleminary test that basic material identificationand main test that strength measure of SHS under interaction of concentrated-compressive load and bendingmoment. The data test results of basic material is used as data input in strength analytical method of a thinwalledsteel square pipe by British Standard meanwhile the test results of a thin-walled steel square pipe isuse as reference of strength analysis method results. The results of SHS pipe strength show that the strengthestimation using the double channels method has a close value to the experimental one (scattered in between2% up to 7%) and this is within acceptable limits of  20 %. This first data results of experimental andstrength analysis by design code are accurate enough and it will be compare with the result of developing astrength analytical method at the next step research.
PRELIMINARY STUDY OF ELASTICITY ON BINARY ALLOY Pramono, Andika Widya; Suryantoro, Anton
Metalurgi Vol 26, No 3 (2011): Metalurgi Vol. 26 No. 3 Desember 2011
Publisher : Pusat Penelitian Metalurgi dan Material - LIPI

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (632.387 KB) | DOI: 10.14203/metalurgi.v26i3.18

Abstract

Apabila setiap komponen dari suatu campuran logam memiliki modulus elastisitas atau struktur kisi (lattice structures)  yang  berbeda,  efek  elastis  akan berpengaruh  pada laju  coarsening serta  morfologi  fasa  yang terbentuk.  Dalam hal  ini  efek  mekanis  yang ditimbulkan  oleh fenomena  elastisitas  ini  lebih  dominan dibandingkan dengan laju difusi dari proses coarsening. Efek elastis mekanis ini kemudian dapat berpengaruh kepada sifat mekanis dari campuran logam tersebut. Makalah ini menyajikan gambaran awal bagaimana efek elastisitas tersebut dapat dikaji dengan menggunakan pendekatan elemen hingga (finite element) melalui penggunaan persamaan Cahn-Hilliard  yang  dilanjutkan dengan Persamaan Parabola Orde  Keempat.  Model Cahn Hilliard dengan efek elastisitas dikembangkan berdasarkan persamaan energi bebas Ginzburg–Landau yang merupakan fungsi dari perbedaan konsentrasi. AbstractIf the components of the mixture have different elastic moduli or different lattice structures, elastic effects might influence the rate of coarsening and the morphology of the particles. In this case the aspect of quasi-static equilibrium for the mechanical part is more predominant than the diffusion mechanism. The resulting elastic effects have a pronounced impact on the evolving coarsening morphology and hence on the material properties. This paper tries to give preliminary consideration on how this elastic behavior is analyzed through finite element approximation using Cahn Hiliard Approach followed by Fourth Order Nonlinear Degenerate Parabolic Equation. Cahn–Hilliard model with elastic contributions is based on a Ginzburg–Landau free energy which is a functional in terms of the concentration difference.
PENGARUH TEMPERATUR DAN WAKTU KALSINASI TERHADAP PERUBAHAN FASA TiO2[Effect Of Temperature And Calcination Time Of Changes In TiO2 Phase] Subagja, Rudi; Royani, Ahmad; Suharyanto, Ariyo; Andriyah, Lia; Natasha, Nadia Chrisayu
Metalurgi Vol 29, No 3 (2014): Metalurgi Vol.29 NO.3 Desember 2014
Publisher : Pusat Penelitian Metalurgi dan Material - LIPI

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (507.95 KB) | DOI: 10.14203/metalurgi.v29i3.298

Abstract

PENGARUH TEMPERATUR DAN WAKTU KALSINASI TERHADAP PERUBAHAN FASA TiO2.Dalam makalah ini disampaikan hasil kegiatan penelitian kalsinasi TiO2 untuk membuat bahan fotokatalis TiO2,dimana bahan TiO2 yang digunakan merupakan hasil dari proses pengolahan ilmenit melalui jalur prosesdekomposisi dengan NaOH, pelarutan titan dari kalsin hasil proses dekomposisi ke dalam larutan asam sulfat,dan pengendapan TiO2. Proses kalsinasi TiO2 dilakukan pada temperatur 300°C sampai dengan 1000°C padaselang waktu 0,5 jam sampai dengan 3 Jam. Kalsin TiO2 yang dihasilkan kemudian dianalisis fasanya denganmenggunakan alat difraksi sinar-x (XRD) dan diuji sifat fotokatalitiknya untuk menguraikan zat warna methylorange dan zat warna yang terkandung dalam limbah industri tekstil. Dari hasil percobaan kalsinasi TiO2 dapatdilihat bahwa fasa anatase cenderung terbentuk pada temperatur lebih rendah dari 600°C. Kenaikan temperaturkalsinasi dari 300 °C menjadi 1000°C cenderung memperkecil terbentuknya fasa anatase, dan kalsin TiO2 yangdipanaskan pada temperatur lebih rendah dari 600°C mempunyai sifat fotokatalitik yang baik dalammenghilangkan zat warna methyl orange. AbstractIn present work, the calcinations experiments to make TiO2 catalytic material were carried out at laboratory scale. The raw material TiO2 used for experiments were prepared by ilmenite decomposition with NaOH followed with titanium dissolution from those decomposed material  into the aqueous sulfuric acid solutions, and precipitation of TiO2 from the solutions. The calcinations experiments were carried out at temperature 300°C up to 1000°C for 0,5 hours until 3 hours. The calcine from experimets were analyzed with X-Ray diffraction method and their  photocatalytic properties  were applied to decompose the methyl orange and dyes materials generated from textile industries. From the result of calcinations experiments, it was observed that anatase was formed at calcinations temperature lower than 600°C. The increase of calcinations temperature from 300°C to 1000°C  decreased the X ray intensities of anatase, and TiO2 material  heated to the temperature lower than 600°C has a better  photocatalytic  properties in  destroying  methyl orange.

Filter by Year

2011 2019


Filter By Issues
All Issue Vol 34, No 3 (2019): Metalurgi Vol. 34 No. 3 Desember 2019 Vol 34, No 2 (2019): Metalurgi Vol. 34 No. 2 Agustus 2019 Vol 34, No 1 (2019): Metalurgi Vol. 34 No. 1 April 2019 Vol 34, No 1 (2019): Metalurgi Vol. 34 No. 1 April 2019 Vol 33, No 3 (2018): Metalurgi Vol. 33 No. 3 Desember 2018 Vol 33, No 2 (2018): Metalurgi Vol. 33 No. 2 Agustus 2018 Vol 33, No 1 (2018): Metalurgi Vol. 33 No. 1 April 2018 Vol 32, No 3 (2017): Metalurgi Vol. 32 No. 3 Desember 2017 Vol 32, No 3 (2017): Metalurgi Vol. 32 No. 3 Desember 2017 Vol 32, No 2 (2017): Metalurgi Vol. 32 No. 2 Agustus 2017 Vol 32, No 2 (2017): Metalurgi Vol. 32 No. 2 Agustus 2017 Vol 32, No 1 (2017): Metalurgi Vol. 32 No. 1 April 2017 Vol 31, No 3 (2016): Metalurgi Vol. 31 No. 3 Desember 2016 Vol 31, No 2 (2016): Metalurgi Vol. 31 No. 2 Agustus 2016 Vol 31, No 1 (2016): Metalurgi Vol. 31 No. 1 April 2016 Vol 30, No 3 (2015): Metalurgi Vol. 30 No. 3 Desember 2015 Vol 30, No 2 (2015): Metalurgi Vol.30 No.2 Agustus 2015 Vol 30, No 1 (2015): Metalurgi Vol.30 No.1 APRIL 2015 Vol 29, No 3 (2014): Metalurgi Vol.29 NO.3 Desember 2014 Vol 29, No 2 (2014): Metalurgi Vol.29 No.2 Agustus 2014 Vol 29, No 1 (2014): Metalurgi Vol.29 No.1 April 2014 Vol 29, No 1 (2014): Metalurgi Vol.29 No.1 April 2014 Vol 28, No 3 (2013): Metalurgi Vol.28 No.3 Desember 2013 Vol 28, No 2 (2013): Metalurgi Vol.28 No.2 Agustus 2013 Vol 28, No 1 (2013): Metalurgi Vol.28 No.1 April 2013 Vol 27, No 3 (2012): Metalurgi Vol.27 No.3 Desember 2012 Vol 27, No 2 (2012): Metalurgi Vol. 27 No. 2 Agustus 2012 Vol 27, No 1 (2012): Metalurgi Vol. 27 No. 1 April 2012 Vol 26, No 3 (2011): Metalurgi Vol. 26 No. 3 Desember 2011 Vol 26, No 2 (2011): Metalurgi Vol.26 No.2 Agustus 2011 Vol 26, No 1 (2011): Metalurgi Vol. 26 No. 1 April 2011 More Issue