Garuda - Garba Rujukan Digital

All

Jurnal Pendidikan Teknik dan Vokasional

jptv
Website

Published by Universitas Negeri Jakarta

ISSN : 25021605 EISSN : 26203065 DOI : https://doi.org/10.21009

Core Subject : Humanities, Science, Education, Social, Engineering,

Humanities Automotive Engineering Chemical Engineering, Chemistry & Bioengineering Civil Engineering, Building, Construction & Architecture Computer Science & IT Control & Systems Engineering Engineering Environmental Science Mechanical Engineering Transportation Other

JPTV (Jurnal Pendidikan Teknik dan Kejuruan) adalah jurnal yang diterbitkan oleh LPPM Universitas Negeri Jakarta. JPTV adalah jurnal yang menerbitkan artikel penelitian asli dan artikel hasil ulasan yang relevan dengan Pendidikan Teknik dan Kejuruan.

Arjuna Subject : Teknik (semua kategori) - Teknik (Lain-Lain)

Articles 94 Documents

2 3 4 5 6

PERCEPATAN WAKTU PENGERJAAN PROYEK KONSTRUKSI DENGAN MENGGUNAKAN METODE FAST TRACK Akhirudin, Ahmad Fajarsyah
Jurnal Pendidikan Teknik dan Vokasional Vol. 3 No. 2 (2020): Jurnal Pendidikan Teknik dan Vokasional
Publisher : LPPM, Universitas Negeri Jakarta

Penelitian ini bertujuan untuk mengetahui pengaruh metode Fast Track pada pelaksanaan proyek konstruksi pada proyek pembangunan Gedung Badan Nasional Penanggulangan Bencana yang berlokasi di Jalan Pramuka Raya, Jakarta Timur. Penelitian ini dilakukan pada proyek pembangunan Gedung BNPB pada bulan September 2013 hingga Mei 2014 dengan metode survey dan wawancara. Setelah survey dan wawancara dilakukan di lokasi penelitian, data-data yang diperoleh dijadikan instrumen dalam pembuatan kuisioner yang selanjutnya diberikan kepada lima orang responden yang dianggap ahli pada bidang konstruksi. Hasil penelitian ini untuk waktu pengerjaan proyek didapat persingkatan waktu selama 21 hari dari waktu yang direncanakan, dengan penambahan biaya yang ditinjau dari segi upah pekerja sebesar Rp. 197.400.000,- atau sebesar 3,4% lebih tinggi dari biaya upah sebelum penelitian ini dilakukan dengan nilai Cost Slope Rp. 9.400.000,-

ANALISIS PENCEMARAN UDARA TERHADAP MASYARAKAT SEKITAR PROTEK MASS RAPID TRANSIT (MRT) JAKARTA CP 103 (Studi Kasus: Jl. Fatmawati, Cipete Utara) Nugroho, Akbar Amir; Rahmayanti, Henita; Murtinugraha, R. Eka
Jurnal Pendidikan Teknik dan Vokasional Vol. 3 No. 1 (2020): Jurnal Pendidikan Teknik dan Vokasional
Publisher : LPPM, Universitas Negeri Jakarta

This study aims to determine the impact of what is most felt by the people around the MRT Jakarta CP 103 project, North Cipete, South Jakarta. This research uses sub-indicators of noise impact and air quality degradation to know the most significant effect and impact factor from air pollution felt by people around North Cipete and South Gandaria due to MRT Jakarta CP 103 construction project. The questionnaire was based on noise and air quality reduction theory, summarized in questionnaire question items to obtain primary data in the MRT Jakarta CP 103 Project community. This study shows that the impact of noise and decreasing air quality resulting from the MRT CP 103 project is likely to be felt by the surrounding community. The project organizers did not explain the impacts resulting from the project in the AMDAL document. These results obtained factors that trigger the effect of disease and material losses felt by the public, namely the use of heavy equipment on the project that produces air pollution. Keywords: air pollution, MRT, society

STUDI KUAT TEKAN BAMBU BETUNG DAN BAMBU HITAM AKIBAT SERANGAN RAYAP TANAH Cut Nyamon Desi; Bachtiar, Gina; Murtinugraha, R. Eka
Jurnal Pendidikan Teknik dan Vokasional Vol. 3 No. 1 (2020): Jurnal Pendidikan Teknik dan Vokasional
Publisher : LPPM, Universitas Negeri Jakarta

This study aims to determine betung and black bamboo's compressive strength due to termites attacks. The research was conducted at the materials test lab at Universitas Negeri Jakarta and Bogor Agricultural University from 1st October 2016 until 30th January 2017. This research method based on ISO-22157:2004 was using the direct testing of compressive strength in the materials test lab. This research used two kinds of bamboo, betung and black bamboo, which amounts to 40 samples. Each bamboo has 20 samples. By the position, each from the base and middle section has ten samples. While each for the treatment by termites and with no termites has five samples. Based on the research result, it can be concluded that the average of the compressive strength value for the betung bamboo from the base and the middle section that given termites have decreased rather than the bamboo that not given termites 14% to be 6%. In comparison, the black bamboos in the middle section have the same decrease on the average of the compressive strength value with the betung bamboo 9,2% to be 23%. But, black bamboos on the base section have the otherwise where the average of the compressive strength that given termites greater than the bamboo that not given termites 3,6% to be 0%. That matter can be caused by termites' attack absences on the base section of the black bamboo samples. In terms of losing weight, all samples lost the weight 6,8% to be 5,5%. This matter happened because the termites attacked the bamboo. But, the bamboo that termites do not attack also can lose weight and can be caused by other factors such as weather (heat and rain) and fungus Keywords: bamboo betung, black bamboo, study of bamboo, termites attack

STUDI KUAT TEKAN BAMBU TALI DAN BAMBU AMPEL AKIBAT SERANGAN RAYAP Deden Wiguna; Bachtiar, Gina; Murtinugraha, R. Eka
Jurnal Pendidikan Teknik dan Vokasional Vol. 3 No. 2 (2020): Jurnal Pendidikan Teknik dan Vokasional
Publisher : LPPM, Universitas Negeri Jakarta

This study aims to determine how the compressive strength of bamboo rope and bamboo Ampel due to termite attack. Where the research was conducted in the Laboratory Test Material Arboretum State University of Jakarta and Bogor Institute of Agriculture in October 1, 2016 - January 30, 2017. This research method using bamboo direct compressive strength testing in the laboratory. In the present study used two types of bamboo, the bamboo rope and bamboo Ampel totaling 40 samples. The total sample of each type of bamboo has the number of 20 samples. According to the position at the base and middle of each totaling 10 samples. For each position there are two treatments, bamboo fed and not fed termites, which amounted to 5 samples. Research conducted compressive strength based on ISO 22 157: 2004. The results showed that the value of the average compressive strength of bamboo and bamboo Ampel rope at the base position and center fed termites decreased from bamboo which is not fed termites. At the base of bamboo straps that are not fed termites of 54.688 kN / cm2.While at the base of bamboo rope that is fed termites of 50.729 kN / cm2.In the central part of bamboo straps that are not fed termites of 54.532 kN / cm2.While on the bamboo rope is fed termites central part of 53.583 kN / cm2.At the base of bamboo Ampel termites were not fed for 51 096 kN / cm2.While at the base of bamboo Ampel were fed termites of 47.084 kN / cm2.In the mid-section of bamboo Ampel not fed termites of 45.559 kN / cm2.While on bamboo Ampel the center that is fed termites of 37.702 kN / cm2.Thus the average value of the weight loss bamboo rope the base that is equal to 8.0% smaller than in the bamboo Ampel the base is equal to 15.1%. While the average value of the weight loss bamboo rope central part that is equal to 12.6% smaller than in the central part of the bamboo Ampel of 14.0%. The average value of compressive strength greater than the bamboo rope bamboo Ampel. This is because the content of starch in the lower rope bamboo from bamboo Ampel. In terms of weight loss (weight) of bamboo seen that the entire sample to lose weight. This is mostly due to termite attack on bamboo. However, bamboo is not attacked by termites also experienced weight loss and can be caused by factors such as the weather (sun and rain) and mushrooms Keywords: study of bamboo, rope and ampel, termites attack

PERENCANAAN STRUKTUR INSTALASI PENGOLAHAN AIR LIMBAH RUMAH PEMOTONGAN HEWAN MENGGUNAKAN METODE ACTIVATED SLUDGE (Studi Kasus Rumah Pemotongan Hewan Pulo Gadung Jakarta Timur) Putra, Wira Agung Syah; Musalamah, Sittati; Rahmayanti, Henita
Jurnal Pendidikan Teknik dan Vokasional Vol. 3 No. 1 (2020): Jurnal Pendidikan Teknik dan Vokasional
Publisher : LPPM, Universitas Negeri Jakarta

This reasearch aims to plan the wastewater treatment unit resulting from the activities of slaughterhouses (RPH) located in RPH Dharma Jaya Pulo Gadung. In planning RPH waste water treatment using Activated Sludge (active sludge) system. This wastewater treatment system will be planned in RPH Dharma Jaya Pulo Gadung neighborhood, East Jakarta. The results of the planning of a container tub, sedimentation tub and aeration tub with a total area of 114 m² overall. The 5 x 4 x 3 m container uses a concrete structure with 8 ø 20 and ø 12 - 100 mm reinforcement bars on its walls and 8 ø 20 and ø 12 - 125 mm bars on the bottom plate of the tub. In the first 3 x 1 x 3 m racking basin using a concrete structure with 8 ø 16 and ø 12 - 125 mm reinforcement on its walls and 8 ø 20 and ø 12 - 75 mm bars on the bottom plate of the tub. In the aeration tub with dimensions of 3 x 2 x 2.3 m using a concrete structure with 6 ø 16 and ø 12 - 100 mm reinforcement on the walls and reinforcement 6 ø 20 and ø 12 - 125 mm on the bottom plate of the tub. For the connecting channel with Q max of 2.85 m³ / sec we obtain the width and channel depth b = 14 cm and d = 7 cm for the channel from Bar Screen to the container. For the channel from the reservoir to the settling tub with Q max of 2.37 m³ / sec obtained b = 14 cm and d = 7 cm. And the channel from the settling tub to the aeration bath is 2.04 m³ / sec with the length b = 12 cm and d = 6 cm. Keywords: activated sludge, planning, wastewater treatment

PENAMBAHAN ABU TEMPURUNG KELAPA TERHADAP KUAT TEKAN PAVING BLOCK Wahyu Saputra; Prihantono; Bachtiar, Gina
Jurnal Pendidikan Teknik dan Vokasional Vol. 3 No. 2 (2020): Jurnal Pendidikan Teknik dan Vokasional
Publisher : LPPM, Universitas Negeri Jakarta

The study aims to find out the influence of the use of grey add coconut shell on paving block against the requirement of quality set out in SNI 03-0691-1996 which includes the nature, size, moisture absorption and powerful press. Ash is produced from coconut shell burning at a temperature of 8000C. The proportion used is 0%, 5%, 6%, 7% and 8% of the cement weight. The study was conducted in Laboratory Test Materials Research Department Civil Engineering State University Of Jakarta. The time the study was conducted in August 2016 with experimental methods in accordance with Indonesia's National Standard (SNI). Making a test done at the factory PD.MAJU PUTRI, Highway 45, 1 No Kavling Cipayung Jak-Team. This type of paving block used was paving block brick-shaped with dimensions of up to 21cm x 10,5cm x 8cm, with a comparison of cement and sand 1:3 by the number of samples as much as 40 fruit. The results of this research to powerful press time soaking 14 and 28 days. The Group of 14 days 0%, 5%, 7

KAPASITAS PELAT LANTAI METODE HALF-SLAB DAN METODE KONVENSIONAL BERDASARKAN VARIASI KETEBALAN Tri Handayani; Aprilin, Ririt; Murtinugraha, R. Eka
Jurnal Pendidikan Teknik dan Vokasional Vol. 3 No. 1 (2020): Jurnal Pendidikan Teknik dan Vokasional
Publisher : LPPM, Universitas Negeri Jakarta

Innovation in floor plate methods has been developing nowadays, one of the methods is the precast method. However, this method cannot behave monolithically with other structures so that the deflection does not meet the permit. To overcome this problem then the half-slab plate innovation comes with a combination of precast and conventional method for the topping. This study discusses the ratio of half-slab and conventional floor plate capacity based on the thickness variation. The capacity analysis covers the bending moment, shear force, deflection and stress due to gravity loads. The total thickness of plate was 120 mm and 130 mm, with the three thickness variations which were the precast is thicker than the topping, the topping is thicker than the precast, and the topping is equal to the precast. The results show that the half-slab plate capacity is 8 to 20 times larger than the conventional plate, due to the lifting and shoring forces. In addition, the variations in the topping and precast thickness affect the value of half-slab capacity, which is the thicker the precast the greater the capacity. Adding thickness every 5 mm could increase the moment capacity by 1,58-7,14%, the shear capacity by 1,61-7,14%, the deflection by 1,69-2,08% and could decrease the normal voltage by 1,76%. So the good variation in the half-slab plate thickness is the plate with the precast thickness which is smaller than the topping thickness. From the two types of plates, plates with a thickness of 130 mm have the capacity 4 to 8 times larger than 120 mm. This is influenced by the lift point placement, shoring plots and a larger 130 mm plate width. Keywords: floor plate capacity, half-slab, thickness variation

PENERAPAN MODEL PEMBELAJARAN BLENDED LEARNING UNTUK MENINGKATKAN HASIL BELAJAR PADA MATA KULIAH FISIKA TERAPAN PPROGRAM STUDI D-3 TEKNIK MESIN UNIVERSITAS NEGERI JAKARTA Dewi Nur Utami; Priyanto, Sugeng; Syaripuddin
Jurnal Pendidikan Teknik dan Vokasional Vol. 4 No. 1 (2021): Jurnal Pendidikan Teknik dan Vokasional
Publisher : LPPM, Universitas Negeri Jakarta

This research aims to determine whether by applying Blended Learning learning models using Moodle applications can improve student learning outcomes of D-3 Mechanical Engineering in Applied Physics courses at Jakarta State University.The method used in this study is Classroom Action Research (CAR) which is a form of investigation conducted by participants involved in the situation under study. The action is followed by observation and reflection. If needed at a later stage, a followup plan is prepared. The effort was carried out in cycles to form one cycle. The place of research was conducted at Jakarta State University, and the research subjects were 29 Mechanical Engineering D3 students. The study was conducted on November 7, 2019 until December 26, 2019. Learning outcomes were obtained through written tests and then analyzed to compare exam results in each cycle.The results of this study indicate that an increase in student learning outcomes in Applied Physics courses by applying Blended Learning learning models using the Moodle application. Improved learning outcomes can be seen in Cycle I the average value of all students is 52.84 and only 51.72% or 15 students out of a total of 29 students who scored ≥60. In Cycle II the mean value of all students was 74.05 and 86.21% or 25 students out of a total of 29 students who scored ≥60. Researchers can conclude student learning outcomes have increased with the application of Blended Learning learning models using the Moodle application. Keywords: applied physics, blended learning, classroom action, learning outcomes, moodle

HUBUNGAN HASIL BELAJAR KEWIRAUSAHAAN DAN PENGALAMAN PRAKTIK KERJA LAPANGAN TERHADAP MINAT BERWIRAUSAHA SISWA SMK KELAS XII KOMPETENSI KEAHLIAN OTOMOTIF Ilham Rizqi Aminudin; Jumhur, Aam Amaningsih; Avanti, Ratu Amalia
Jurnal Pendidikan Teknik dan Vokasional Vol. 4 No. 1 (2021): Jurnal Pendidikan Teknik dan Vokasional
Publisher : LPPM, Universitas Negeri Jakarta

This study aims to determine the relationship between the learning outcomes of entrepreneurship and job training experience with a class XII student interest in entrepreneurship competence automotive expertise SMK X. This research method is correlation method. The population in this study is a class XII student competence automotive expertise SMK North Jakarta area as many as 4,461 students in 2019/2020, SMK 55, SMK 56, SMK 4, and SMK 36. The sampling technique used purposive sampling to determine the size of the sample using the formula Slovin and data analysis technique used is simple regression analysis and correlation. The results of this study were (1) the results of entrepreneurial learning has a positive and significant relationship to the interest in entrepreneurship class at SMK XII North Jakarta area with r1 values of 0.181 and a r2 by 3,2%. (2) Experience job training has a positive and significant relationship to the interest in entrepreneurship class XII at SMK Region North Jakarta with a value of r2 0,452 and a r2 by 20,3% (3) the results of study entrepreneurship and practical experience of field work jointly have a positive influence and significantly to class XII student interest in entrepreneurship at SMK North Jakarta area with values of 0.479 and r3 r2 result by 23%. Keywords: Quantitative Associative, Relationship Research, Interest In Entrepreneurship

PENGEMBANGAN PERANGKAT PEMBELAJARAN PADA EDUKASI BAHAYA KEBAKARAN DAN UPAYA PENYELAMATAN DIRI DENGAN METODE PROBLEM BASED LEARNING BERBASIS HIGHER ORDER THINKING SKILLS PADA SISWA KELAS V Aditya Hermawan; Avanti, Ratu Amalia; Sukarno, Ragil
Jurnal Pendidikan Teknik dan Vokasional Vol. 4 No. 2 (2021): Jurnal Pendidikan Teknik dan Vokasional
Publisher : LPPM, Universitas Negeri Jakarta

This study aims to develop a web-based learning model on the fuel system material and determine the feasibility of the learning model product based on the assessment of 2 material experts, 2 media experts and 30 students at SMK Negeri 54 Jakarta. This research method is Research and Development (R&D) with the ADDIE development model consisting of five stages, namely Analysis, Design, Development, Implementation, and Evaluation. The results in this study are a web-based learning model that can be accessed via computers and smartphones with the address https://teknikengine.000webhostapp.com. In this study, it was shown that the level of feasibility of the learning model based on the assessment of material experts from all aspects obtained a percentage of 88.33% which was included in the "Very Eligible" category. Media experts in all aspects obtained a percentage of 85.38% which was included in the "Very Eligible" category and the satisfaction results by students in all aspects obtained a percentage of 89.23% which was included in the "Very Satisfied" category. Thus, the web-based learning model on this fuel system material is "Very Appropriate" to be used as a learning model Keywords: Learning Model Development, Feasibility

Page 4 of 10 | Total Record : 94

2 3 4 5 6

Filter by Year

2015 2025

Filter By Issues

All Issue Vol. 8 No. 1 (2025): Jurnal Pendidikan Teknik dan Vokasional Vol. 7 No. 1 (2024): Jurnal Pendidikan Teknik dan Vokasional Vol. 6 No. 2 (2023): Jurnal Pendidikan Teknik dan Vokasional Vol. 6 No. 1 (2023): Jurnal Pendidikan Teknik dan Vokasional Vol 5 No 2 (2022): Jurnal Pendidikan Teknik dan Vokasional Vol 5 No 1 (2022): Jurnal Pendidikan Teknik dan Vokasional Vol. 4 No. 2 (2021): Jurnal Pendidikan Teknik dan Vokasional Vol. 4 No. 1 (2021): Jurnal Pendidikan Teknik dan Vokasional Vol. 3 No. 2 (2020): Jurnal Pendidikan Teknik dan Vokasional Vol. 3 No. 1 (2020): Jurnal Pendidikan Teknik dan Vokasional Vol. 2 No. 2 (2016): Jurnal Pendidikan Teknik dan Vokasional Vol. 2 No. 1 (2016): Jurnal Pendidikan Teknik dan Vokasional Vol. 1 No. 1 (2015): Jurnal Pendidikan Teknik dan Vokasional More Issue

Home Page

OAI Link

Editorial Team

Contact

Reviewer

Google Scholar

Contact Name
Imam Basori

Contact Email
unj.jptv@gmail.com

Phone
+6285274624665

Journal Mail Official
unj.jptv@gmail.com

Editorial Address
L Building, Faculty of Engineering, Universitas Negeri Jakarta Jl. Rawamangun Muka, RT 11/RW 14, Rawamangun, Jakarta Timur

Location
Kota adm. jakarta timur,

Dki jakarta

INDONESIA

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Home Page

OAI Link

Editorial Team

Contact

Reviewer

Google Scholar

Contact Name Imam Basori

Contact Email unj.jptv@gmail.com

Phone +6285274624665

Journal Mail Official unj.jptv@gmail.com

Editorial Address L Building, Faculty of Engineering, Universitas Negeri Jakarta Jl. Rawamangun Muka, RT 11/RW 14, Rawamangun, Jakarta Timur

Location Kota adm. jakarta timur, Dki jakarta INDONESIA

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Contact Name
Imam Basori

Contact Email
unj.jptv@gmail.com

Phone
+6285274624665

Journal Mail Official
unj.jptv@gmail.com

Editorial Address
L Building, Faculty of Engineering, Universitas Negeri Jakarta Jl. Rawamangun Muka, RT 11/RW 14, Rawamangun, Jakarta Timur

Location
Kota adm. jakarta timur,

Dki jakarta

INDONESIA