Garuda - Garba Rujukan Digital

Article Per Year (5 Year)

All

JURNAL TEKNIK INDUSTRI

tekin
Website

Published by Universitas Trisakti

ISSN : 14116340 EISSN : 26225131 DOI : https://doi.org/10.25105/jti

Core Subject : Science, Engineering,

Electrical & Electronics Engineering Energy Industrial & Manufacturing Engineering

Jurnal Teknik Industri (JTI) mainly focuses on industrial engineering scientific essays in the form of research results, surveys and literature review that are closely related to the Field of Industrial Engineering

Arjuna Subject : Teknik (semua kategori) - Tenik Industri dan Manufaktur

Articles 385 Documents

17 18 19 20 21

PENGAMBILAN KEPUTUSAN DENGAN PENDEKATAN NON-NUMERICAL MULTI EXPERT-MULTI CRITERIA DALAM PENANGANAN KECACATAN PRODUKSI TUBE PADA PT. BONA METAL PACKAGING Nunung Nurhasanah; Duffi Januwar
JURNAL TEKNIK INDUSTRI Vol. 2 No. 2 (2012): Volume 2 No 2 Juli 2012
Publisher : Jurusan Teknik Industri, Fakultas Teknologi Indusri Universitas Trisakti

PT. Bona Metal Packaging is a company that move within area of making alumunium tube. The company will be hard to compete if the product result often get defect in production time that the rate of production defect in ranging at 10%, so hopefully there is alternative solution that the company need the most this moment. The objective of this research is to analyze priority solution in minimize tube defect in production process with the use of semi automatic machine.This research begin with finding the cause factor of defect in tube production. Then formulate and choose alternative solution with the use of method non-numerical multi expert multi criteria decision making (ME-MCDM). Base on the result so the problem lies on the operator then need to making efficient use of the operator. The usefullness can be done with the training of operator.

ANALISA SUPPLY CHAIN RISK MANAGEMENT BERDASARKAN METODE FAILURE MODE AND EFFECTS ANALYSIS (FMEA) Nurlailah Badariah; Dadang Surjasa; Yuda Trinugraha
JURNAL TEKNIK INDUSTRI Vol. 2 No. 2 (2012): Volume 2 No 2 Juli 2012
Publisher : Jurusan Teknik Industri, Fakultas Teknologi Indusri Universitas Trisakti

Today PT. Jakarta Pertamina Unit Produksi Pelumas Jakarta (UPPJ) has some problems with inbound supply of raw materials. Deficiency dock may pose risks to the process of loading raw material base oil, resulting in delay in supply of raw materials. This delay could have an impact on other processes, such as delays to produce, and iddle of existing production facilities at the plant; it would be very detrimental to the company if the obstacle is often the case. Supply chain management is always influenced by three factors, namely how to reduce costs, reduce time and improve quality. If at first study on supply chain management is only classified in three categories, namely the field of operations, design and strategy, then this can be added to the four categories, namely the field of risk, which is commonly referred to as supply chain risk Management (SCRM). Based on the problems that occurred the first stage done is to identify risks in each process and then determine the influence of the effect in terms of cost, time and quality of the results of the determination of the influence. the next step is to determine the weights based on the severity of the bottleneck (severity), the possibility of resistance (Occurrence) and the possible causes of the barriers can be detected (Detection). The last step is to calculate the Risk priority Number (RPN) is obtained from the product of severity, Occurrence and Detection then obtained the highest priority for 144 the factors that most influence the leak rate of the production process.

ANALISA KESEIMBANGAN LINI PADA DEPARTEMEN CHASSIS PT TOYOTA MOTOR MANUFACTURING INDONESIA DENGAN ALGORITMA ANT COLONY, RANK POSITIONAL WEIGHT, DAN ALGORITMA GENETIKA Lina Gozali; Lamto Widodo; Martin Bernhard
JURNAL TEKNIK INDUSTRI Vol. 2 No. 2 (2012): Volume 2 No 2 Juli 2012
Publisher : Jurusan Teknik Industri, Fakultas Teknologi Indusri Universitas Trisakti

PT . Toyota Motor Manufacturing Indonesia is a company engaged in the automotive industry. The longest cycle time can also be caused by many things, from the unequal division of labor so that the necessary analysis for the balance of the assembly line. In writing this Final analysis used the balance line is Ant Colony Algorithm, Rank Positional Weight, and Genetic Algorithms. All three methods of analysis will produce an analysis for the improvement of the assembly lines now run so as to achieve the targets that have been defined. With a high efficiency line of the balance delay of the assembly line will also be getting smaller and makes no waiting time from the operator. All the time can be optimally used to produce the product. Of the three analysis the analysis with the highest efficiency, smallest delay balance and smoothness index of the smaller to be selected as the best proposal. Analysis of this problem is best for analysis using ant colony algorithm with line efficiency 93.2%, 6.8% delay Balance and Smoothness index 45.77

PERBANDINGAN PENGUKURAN WAKTU BAKU DENGAN METODE STOPWATCH TIME STUDY DAN METODE READY WORK FACTOR (RWF) PADA DEPARTEMEN HAND INSERT PT. SHARP INDONESIA Nataya Charoonsri Rizani; Dian Mardi Safitri; Prita Ayu Wulandari
JURNAL TEKNIK INDUSTRI Vol. 2 No. 2 (2012): Volume 2 No 2 Juli 2012
Publisher : Jurusan Teknik Industri, Fakultas Teknologi Indusri Universitas Trisakti

Production target of Department Hand Inserts PT Sharp Indonesia which was often not achieved, making the company intended to know the cause of the problem. Time study was needed to set production targets against operator’s ability. Time study established by the holding company of Japan using ready work factors (RWF) method. To determine conformity RWF method, a comparison with stopwatch time study was conducted. There were differences in the value of standard time with both methods. The differences due to value of rating operator performance and allowance. The value in RWF method was smaller than the findings in the field. After a change of both value the difference between the two methods became smaller. After that with standard time from RWF method was calculated operator's ability to produce. The results indicated that the ability of the operator under the production target, so improvement was needed.

PERANCANGAN TATA LETAK DEPARTEMEN FINISHING PABRIK CV. SG-BANDUNG Nita Puspita Anugrawati Hidayat
JURNAL TEKNIK INDUSTRI Vol. 2 No. 2 (2012): Volume 2 No 2 Juli 2012
Publisher : Jurusan Teknik Industri, Fakultas Teknologi Indusri Universitas Trisakti

CV. SG Bandung is a convection company that produces moslem clothes. High competitive in market push company to be more effective and efficient.Company must be able to increase productivity on the production floor and reduce cost.From this observation, CV. SG doesn’t have a good layout. It seen from the departments and facilities in finishing department placement that have not been arranged properly. One of the parameters of a good layout is minimize material handling cost which can be seen from the movement moment, which is calculated by multiplying the distance and frequency of material movement between facilities. Before preparing the new layout, it needs the initial layout, from-to chart, move-cost chart which becomes input for CRAFT algorithm in the WinQSB software.Through this research, can be obtained the plant facility layout design is better, it can be seen from the movement moment which can be reduced in the finishing department proposed layout.

PENERAPAN KONSEP LEAN MANUFACTURING UNTUK MENINGKATKAN KAPASITAS PRODUKSI (STUDI KASUS : LANTAI PRODUKSI PT.TATA BROS SEJAHTERA) Sumiharni Batubara; Fidiarti Kudsiah
JURNAL TEKNIK INDUSTRI Vol. 2 No. 2 (2012): Volume 2 No 2 Juli 2012
Publisher : Jurusan Teknik Industri, Fakultas Teknologi Indusri Universitas Trisakti

Lean Manufacturing is an approach to increase the efficiency of a system through a continuous improvement to minimize waste. This approach begins by creating a value stream mapping, an overview of an organization through information/activity flow and material flow that takes place at the shop floor. These activities are then classified as value-added activities and non-value added activities. The complication arises when production target cannot be met, delaying product delivery to consumers. This delay, mainly driven by lengthy production time, is typically caused by waste that occurs at the shop floor. By identifying the source of those wastes, production time can be reduced to fulfill production target. This paper utilized the lean manufacturing approach as an initial step to perform standard time calculation for all activities that eventually were identified as Value-added or Non Value-added Current State Activity. Further, to obtain the complete picture of the shop floor, value stream mapping were performed and Process Cycle Efficiency was calculated. Waste, defined as transportation time required for semi-finished products from one process to the next and any unnecessary motions within some process, were then identified. To minimize transportation time, transfer batch was utilized. While to decrease operation time, motion improvements were done through Right Hand – Left Hand Process Chart. Upon improvement, manufacturing lead time decreased by 4.7% and Process Cycle Efficiency increased by 2%.

PENGUKURAN KEPUASAN PELANGGAN MENGGUNAKAN METODE KANO DAN ROOT CAUSE ANALYSIS (STUDI KASUS PLN TANGERANG) Tiena Gustina Amran; Ponti Ekadeputra
JURNAL TEKNIK INDUSTRI Vol. 2 No. 2 (2012): Volume 2 No 2 Juli 2012
Publisher : Jurusan Teknik Industri, Fakultas Teknologi Indusri Universitas Trisakti

National Electric Power Company (Perusahaan Listrik Negara/PLN) according to its commitment has to upgrade its service quality to the society as the only company supplying electrical power where the custoner satisfaction is become a very important matter. By maintaining the customer satisfaction means to upgrade good image of the company and minimizing customer complains. By using the Kano approach which is known as attributes that entered the four areas which are: ‘Must be’, “One dimensional”,”Attractive” and ”Indifferent”. Based on the research carried out it was hoped with the customer's Satisfaction Index in the position which is quite satisfactory. To explore the improvement of problem solution could be done by using Root Cause Analysis which will give big impact to the company. This improvement will appear in the fact of fast services for instance in direct ticket purchasing, installation direct improvemen, and quick respons and contact of the PLN call center.

PENGAMANAN SOAL UJIAN DENGAN BANTUAN PERANGKAT LUNAK AxCrypt Sucipto Adisuwiryo
JURNAL TEKNIK INDUSTRI Vol. 2 No. 2 (2012): Volume 2 No 2 Juli 2012
Publisher : Jurusan Teknik Industri, Fakultas Teknologi Indusri Universitas Trisakti

An Examination is a way to represent one’s ability into a certain grade. That’s why, it is confidential. Only certain people have the autorization in accessing the document. The document needs to be protected whether it is saved in hardisk, external hardisk, usb flashdisk or ‘sent item’ in email. The protection can be done by transforming the document into a confidential document so it can’t be seen by others. The transformation is called encription. Otherwise, it is called decription for transforming document into inconfidential document.The AxCrypt Tool can be used to protect exam document by encripting and open the document by decripting using password and key-file. AxCrypt is usefull for protecting the exam document that is saved in public computer, sending the classified exam document using email interface, and making only certain coordinator and lecturer who is responsible for the document, can open dan read the document.

PENJADWALAN PESANAN MENGGUNAKAN ALGORITMA GENETIKA UNTUK TIPE PRODUKSI HYBRID AND FLEXIBLE FLOWSHOP PADA INDUSTRI KEMASAN KARTON Nora Azmi; Irawadi Jamaran; Yandra Arkeman; Djumali Mangunwidjaja
JURNAL TEKNIK INDUSTRI Vol. 2 No. 2 (2012): Volume 2 No 2 Juli 2012
Publisher : Jurusan Teknik Industri, Fakultas Teknologi Indusri Universitas Trisakti

This research was intended to produce an order (job) scheduling model at Carton Packaging Industries (CPI) that is useful for giving information about the time delivery to customers. The proposed model is quite complicated because of the characteristic of Make to Order (MTO) varies production process greatly between each order. The job’s schedule for CPI is prepared for production process that consists of 5 stages where in each stage uses different type of machinery. Not all jobs can be processed by all machines at a given production stage. Every job flow through 5 stage in the same order, but not all stages have to visited by all jobs. Stages may be skipped for a particular job. This condition makes CPI is classified as Hybrid and flexible flowshop for machine eligibility (HFFME). HFFME is complicated and is difficult to calculate by using conventional heuristic model. This research used genetic algorithm for solving the complex problem of HFFME and the resulting model called the Genetic Algorithm for hybrid and flexible flowshop with machine eligibility (GA-HFFME). This model is developed to minimized makespan, the objective of scheduling. The experiment was conducted towards 11 orders and it was found that the GA-HFFME is effective to solve that problem.

PERANCANGAN PENJADWALAN FLOWSHOP MENGGUNAKAN PARTICLE SWARM OPTIMIZATION UNTUK MEMINIMASI NUMBER OF TARDY JOBS Rahmi Maulidya; Docki Saraswati; Divani Vania
JURNAL TEKNIK INDUSTRI Vol. 2 No. 2 (2012): Volume 2 No 2 Juli 2012
Publisher : Jurusan Teknik Industri, Fakultas Teknologi Indusri Universitas Trisakti

This paper propose an algorithm for general flowshop scheduling problems using Particle Swarm Optimization that can minimize number of tardy jobs. The algorithm is illustrated in a case study from the heavy equipment manufacturing industry. The proposed algorithm based on Particle Swarm Optimization algorithm developed by Tasgetiren using routing symbols, combined with the characteristic of its production. The jobs would be process in first work station using Particle Swarm Optimization approaches, for 2nd until 11th works stasion using first come first served rules and earliest due date rules for assembly’s works station.

Page 19 of 39 | Total Record : 385

17 18 19 20 21

Filter by Year

2011 2025

Filter By Issues

All Issue Vol. 15 No. 3 (2025): November 2025 Vol. 15 No. 2 (2025): July 2025 Vol. 15 No. 1 (2025): March 2025 Vol. 14 No. 3 (2024): November 2024 Vol. 14 No. 2 (2024): July 2024 Vol. 14 No. 1 (2024): March 2024 Vol. 13 No. 3 (2023): VOLUME 13 NO 3 NOVEMBER 2023 Vol. 13 No. 2 (2023): VOLUME 13 NO 2 JULI 2023 Vol. 13 No. 1 (2023): VOLUME 13 NO 1 MARET 2023 Vol. 12 No. 3 (2022): VOLUME 12 NO 3 NOVEMBER 2022 Vol. 12 No. 2 (2022): VOLUME 12 NO 2 JULI 2022 Vol. 12 No. 1 (2022): VOLUME 12 NO 1 MARET 2022 Vol. 11 No. 3 (2021): VOLUME 11 NO 3 NOVEMBER 2021 Vol. 11 No. 2 (2021): VOLUME 11 NO 2 JULI 2021 Vol. 11 No. 1 (2021): VOLUME 11 NO 1 MARET 2021 Vol. 10 No. 3 (2020): Volume 10 No 3 November 2020 Vol. 10 No. 2 (2020): Volume 10 No 2 Juli 2020 Vol. 10 No. 1 (2020): VOLUME 10 NO 1 MARET 2020 Vol. 9 No. 3 (2019): Volume 9 No 3 November 2019 Vol. 9 No. 2 (2019): VOLUME 9 NO 2 JULI 2019 Vol. 9 No. 1 (2019): Volume 9 No 1 Maret 2019 Vol. 8 No. 2 (2018): Volume 8 N0 2 Juli 2018 Vol. 8 No. 3 (2018): Volume 8 No 3 November 2018 Vol. 8 No. 1 (2018): Volume 8 No 1 Maret 2018 Vol. 7 No. 3 (2017): Volume 7 No 3 November 2017 Vol. 7 No. 2 (2017): Volume 7 Nomor 2 Juli 2017 Vol. 7 No. 1 (2017): Volume 7 Nomor 1 Maret 2017 Vol. 6 No. 3 (2016): Volume 6 No 3 November 2016 Vol. 6 No. 2 (2016): Volume 6 No 2 Juli 2016 Vol. 6 No. 1 (2016): Volume 6 No 1 Maret 2016 Vol. 5 No. 3 (2015): Volume 5 No 3 Novemberi 2015 Vol. 4 No. 3 (2014): Volume 4 No. 3 November 2014 Vol. 4 No. 2 (2014): Volume 4 No 2 Juli 2014 Vol. 4 No. 1 (2014): Volume 4 No 1 Maret 2014 Vol. 3 No. 3 (2013): Volume 3 No 3 November 2013 Vol. 3 No. 2 (2013): Volume 3 No 2 Juli 2013 Vol. 3 No. 1 (2013): Volume 3 No 1 Maret 2013 Vol. 2 No. 3 (2012): Volume 2 No 3 November 2012 Vol. 2 No. 2 (2012): Volume 2 No 2 Juli 2012 Vol. 2 No. 1 (2012): Volume 2 No 1 Maret 2012 Vol. 1 No. 2 (2011): Volume 1 No 2 Juli 2011 Vol. 1 No. 1 (2011): Volume 1 No 1 Maret 2011 More Issue

Home Page

OAI Link

Editorial Team

Contact

Reviewer

Google Scholar

Contact Name
Parwadi Moengin

Contact Email
parwadi@trisakti.ac.id

Phone
+628128210951

Journal Mail Official
jurnalti@trisakti.ac.id

Editorial Address
Jurusan Teknik Industri FTI Universitas Trisakti Gedung Heri Hartanto Lantai 5 JL. Kyai Tapa no 1, Grogol, Jakarta Barat-11440

Location
Kota adm. jakarta barat,

Dki jakarta

INDONESIA

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Home Page

OAI Link

Editorial Team

Contact

Reviewer

Google Scholar

Contact Name Parwadi Moengin

Contact Email parwadi@trisakti.ac.id

Phone +628128210951

Journal Mail Official jurnalti@trisakti.ac.id

Editorial Address Jurusan Teknik Industri FTI Universitas Trisakti Gedung Heri Hartanto Lantai 5 JL. Kyai Tapa no 1, Grogol, Jakarta Barat-11440

Location Kota adm. jakarta barat, Dki jakarta INDONESIA

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Contact Name
Parwadi Moengin

Contact Email
parwadi@trisakti.ac.id

Phone
+628128210951

Journal Mail Official
jurnalti@trisakti.ac.id

Editorial Address
Jurusan Teknik Industri FTI Universitas Trisakti Gedung Heri Hartanto Lantai 5 JL. Kyai Tapa no 1, Grogol, Jakarta Barat-11440

Location
Kota adm. jakarta barat,

Dki jakarta

INDONESIA