cover
Contact Name
Arsyad Ramadhan Darlis
Contact Email
arsyad@itenas.ac.id
Phone
-
Journal Mail Official
jte.itenas@itenas.ac.id
Editorial Address
-
Location
Kota bandung,
Jawa barat
INDONESIA
ELKOMIKA: Jurnal Teknik Energi Elektrik, Teknik Telekomunikasi, & Teknik Elektronika
ISSN : 23388323     EISSN : 24599638     DOI : -
Core Subject : Engineering,
Jurnal ELKOMIKA diterbitkan 3 (tiga) kali dalam satu tahun pada bulan Januari, Mei dan September. Jurnal ini berisi tulisan yang diangkat dari hasil penelitian dan kajian analisis di bidang ilmu pengetahuan dan teknologi, khususnya pada Teknik Energi Elektrik, Teknik Telekomunikasi, dan Teknik Elektronika.
Arjuna Subject : -
Articles 826 Documents
Perancangan Kendali Multilevel Inverter Satu Fasa Tiga Tingkat dengan PI+feedforward pada Beban Nonlinier NUGROHO, MOCHAMAD ARI BAGUS; WINDARKO, NOVIE AYUB; SUMANTRI, BAMBANG
ELKOMIKA: Jurnal Teknik Energi Elektrik, Teknik Telekomunikasi, & Teknik Elektronika Vol 7, No 3: Published September 2019
Publisher : Institut Teknologi Nasional, Bandung

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.26760/elkomika.v7i3.493

Abstract

ABSTRAKSebuah konverter daya multilevel inverter diharapkan mampu untuk menyuplai tegangan AC ideal pada kondisi beban linier maupun nonlinier. Diharapkan metode kendali mampu cepat tanggap dan mampu mempertahankan bentuk tegangan AC keluaran inverter. Pengendali PI+feedforward diajukan dalam makalah ini. Pengendali ini akan diuji dengan beban linier maupun nonlinier. Beban nonlinier berupa rangkaian penyearah dengan filter kapasitor. Berdasarkan pengujian simulasi didapatkan bahwa pengendali PI+feedforward lebih cepat tanggap terhadap gangguan yang dibuktikan dengan nilai kesalahan rata-rata absolut sekitar 73% lebih kecil dari pengendali PI. Hasil Simulasi menunjukkan bahwa multilevel inverter dengan kendali PI menghasilkan THDv sebesar 0,669% pada beban linier dan sebesar 1,263% pada kondisi beban nonlinier. Sedangkan dengan kendali PI+feedforward menghasilkan THDv sebesar 0,292% pada beban linier dan sebesar 1,044% pada kondisi beban nonlinier.Kata kunci: mutilevel inverter, pengendali PI, feedforward, beban non-linier ABSTRACTA multilevel inverter power converter is expected to be able to supply ideal AC voltage in linear and nonlinear load conditions. It is expected that the control method is be able to respond quickly and be able to maintain the waveform of the inverter output AC voltage. PI + feedforward controller is proposed in this paper. This controller will be tested with linear and nonlinear loads. Nonlinear load is a rectifier circuit with a filter capacitor. Based on simulation it was found that PI + feedforward controllers were more responsive to interference as evidenced by the mean absolute error (MAE) value of about 73% less than the PI controller. Simulation results show that multilevel inverter with PI control produces THDv of 0.669% in linear load and 1.263% in nonlinear load conditions. Whereas with PI + feedforward control produces THDv of 0.292% in linear loads and of 1.044% in nonlinear load conditions.Keywords: multilevel inverter, PI controller, feedforward, non-linear load
Pemurnian Biogas untuk meningkatkan Nilai Kalor melalui Adsorpsi Dua Tahap Susunan Seri dengan Media Karbon Aktif SUPRIANTI, YANTI
ELKOMIKA: Jurnal Teknik Energi Elektrik, Teknik Telekomunikasi, & Teknik Elektronika Vol 4, No 2: Published July - December 2016
Publisher : Institut Teknologi Nasional, Bandung

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.26760/elkomika.v4i2.185

Abstract

ABSTRAKPemerintah menargetkan peningkatan peran energi terbarukanhingga mencapai 24% pada tahun 2050. Biogas sebagai salah satu dari sumber energi terbarukan harus memiliki nilai kalor yang memadaiagar dapat bersaing dengan sumber energi fosil. Zat yang memiliki kontribusi terbesar dalam menentukan nilai kalor biogas adalah Metana (CH4). Namun, biogas juga memiliki kandungan Karbon dioksida (CO2) yang bersifat tidak terbakar. Upaya untuk meningkatkan nilai kalor biogas dapat ditempuh dengan menurunkan kandungan CO2, salah satunya melalui proses adsorpsi. Penelitian ini menggunakan kolom adsorpsi seri berukuran 2,43 L untuk meningkatkan waktu kontak antara adsorben karbon aktif dengan gas-gas kontaminan. Hasil penelitian menunjukkan bahwa kandungan CO2 dapat ditekan hingga di bawah 14% pada waktu adsorpsi 10 menit,dan diperoleh kandungan CH4 hingga minimal 78,73%. Hasil optimum kinerja kolom adsorpsi seri yaitu pada laju alir 2,4 L/menit dan waktu adsorpsi 10 menit, mampu memurnikan biogas hingga mengandung CH4 91,60%. Pada kondisi optimum tersebut, efektifitas kolom adsorpsi adalah sebesar 98,31%.Kata kunci: biogas, pemurnian, karbon aktif, waktu adsorpsi, efektifitas kolom adsorpsi.ABSTRACTIndonesian government had targettedthe role of renewable energy, up to 24% in 2050. Biogas, as one of renewable energy, should have sufficient calorific valuein order to be efficiently used and competitive compared to fossil fuels. Methane (CH4) in biogas is the most important substance that determine biogas calorific value. On the other hand, another component of biogas, Carbon dioxide (CO2), the one that inhibit combustion process must be reduced. One of the methods to reduce CO2 content can be conducted through adsorption process. This research utilized serial adsorption column to increase contact between activated carbon as adsorbent and contaminant gases. The result showed that CO2 content can be suppressed below 14% in 10 minutes adsorption time, so that CH4 content can be upgraded above 78.73%. The optimum performance of serial adsorption column obtained at 2.4 lpm of biogas flow in 10 minutes adsorption time, able to purify biogas to 91.60% of CH4 content. In optimum condition, serial adsorption column effectiveness was 98.31%.Keywords: biogas, purification, activated carbon, adsorption time, serial adsorption column effectiveness.
Pembangkitan Pulsa Orde Nanodetik Berbasis Mikrokontroler Untuk Eksitasi Transduser Ultrasonik MUQAFFI, FAATIH RIFQI; WIBAWA, BAMBANG MUKTI; HIDAYAT, DARMAWAN
ELKOMIKA: Jurnal Teknik Energi Elektrik, Teknik Telekomunikasi, & Teknik Elektronika Vol 8, No 1: Published January 2020
Publisher : Institut Teknologi Nasional, Bandung

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.26760/elkomika.v8i1.229

Abstract

ABSTRAK Makalah ini melaporkan suatu teknik pembangkitan pulsa lebar orde nanodetik (ns) repetitif yang terprogram berbasis mikrokontroler untuk keperluan eksitasi transduser ultrasonik. Pembangkitan pulsa dan pengaturan jarak antar pulsa dilakukan melalui operasi timer mikrokontroler. Sebuah monostable multivibrator mengubah lebar pulsa dari mikrokontroler dalam orde nanodetik melalui pengaturan komponen pewaktuan resistor-kapasitor (RC) dengan cara pengaturan nilai R yang dibuat dari sebuah potensiometer digital. Hasil pengujian menunjukkan bahwa mikrokontroler membangkitkan pulsa repetitif dengan interval terprogram dalam orde 1 detik dan lebar pulsa minimum 1,25 ms. monostable multivibrator dapat mengubah lebar pulsa tersebut menjadi sekitar 140 ns. Berdasarkan hasil pengujian, dapat disimpulkan bahwa sistem berfungsi sesuai rancangan, sistem dapat membangkitkan pulsa repetitif dengan lebar pulsa hingga 140 ns dengan parameter interval dan lebar yang dapat diprogram. Kata kunci: generator pulsa, lebar pulsa singkat, mikrokontroler, monostable multivibrator, eksitasi transduser ultrasonik  ABSTRACT This paper reports a repetitive, programmable, microcontroller-based pulse width generation technique for the purpose of ultrasonic transducer excitation. Pulse generation and distance adjustment between pulses is done through the microcontroller timer. A monostable multivibrator changes the pulse width of the microcontroller in the order of nanoseconds by adjusting the resistor-capacitor time constant which are done by adjusting the R value made from a digital potentiometer. The test results show that the microcontroller generates repetitive pulses with programmed intervals in order of 1 second and pulse width of 1.25 ms. A monostable multivibrator converts the pulse width to ca. 140 ns. Based on the test results, it can be concluded that the system functions according to the design as the system can generate repetitive pulses with pulse widths up to 140 nanoseconds with programmable interval and width parameters. Keywords: pulse generator, short-width pulse, microcontroller, monostable multivibrator, ultrasonic transducer excitation
Indeks Subjeks dan Indeks Pengarang -, - INDEKS
ELKOMIKA: Jurnal Teknik Energi Elektrik, Teknik Telekomunikasi, & Teknik Elektronika Vol 6, No 1: Published January 2018
Publisher : Institut Teknologi Nasional, Bandung

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.26760/elkomika.v6i1.%p

Abstract

Indeks Subjeks dan Indeks Pengarang
Karakterisasi Prototipe Heater Element System pada Untai Uji RCCS-RDNK menggunakan Kamera Infra Merah HARYANTO, DEDY; GIARNO, GIARNO; WITOKO, JOKO PRASETIO; KUSNUGROHO, GREGORIUS BAMBANG HERU; KUSUMASTUTI, RAHAYU; JUARSA, MULYA
ELKOMIKA: Jurnal Teknik Energi Elektrik, Teknik Telekomunikasi, & Teknik Elektronika Vol 8, No 2: Published May 2020
Publisher : Institut Teknologi Nasional, Bandung

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.26760/elkomika.v8i2.313

Abstract

ABSTRAKReactor Cavity Cooling System (RCCS) adalah salah satu sistem keselamatan pada Reaktor Daya Non Komersial (RDNK). Untuk mensimulasikan keadaaan tersebut, dibuat prototype Heater Element System (HES) yang merupakan sistem pemanas listrik dan berfungsi untuk memberikan kalor pada simulator dinding RPV (wall) seperti pada acuan RPV tipe HTGR. Tujuan penelitian adalah untuk memperoleh karakteristik temperatur selama pemanasan prototype HES hingga mencapai temperature 400°C berdasarkan posisi vertikal dan horizontal HES. Metode pengamatan dilakukan dengan menggunakan kamera infra merah NEC tipe TH9100ML sebagai alat ukur temperatur dan alat visualisasi ditribusi temperatur. Hasil pengamatan menunjukkan, bahwa kehilangan kalor pada prototipe HES pada posisi vertikal lebih kecil dibandingankan pada posisi horizontal hal ini disebabkan karena luas permukaan pada posisi horizontal sebesar 7,260 cm2 lebih memungkinkan untuk kehilangan kalor lebih besar. Posisi vertikal temperatur yang dicapai pada wall prototipe HES lebih tinggi dibandingkan pada posisi horizontal.Kata Kunci: RCCS, Heater Element System, kamera infra merah, temperatur ABSTRACTReactor Cavity Cooling System (RCCS) is one of the safety systems in Non-Commercial Power Reactors (RDNK). To simulate this situation, a prototype Heater Element System (HES) was made using electric heating system as a heat sources and it serves to provide radiation heat to the RPV wall simulator as the reference of the RPV of HTGR type. The purpose of this study was to obtain the temperature characteristics during the heating of the HES prototype to reach temperatures of 400°C base on HES position, horizontal and vertical positions. The observation method was carried out using a TH9100ML infrared camera NEC type as a temperature measurement and a temperature distribution base on visualization. The observations show that the heat loss in the HES prototype in the vertical position is smaller than in the horizontal position because this is because the surface area in the horizontal position 7.260 cm2 is more likely to lose more heat. The vertical position the temperature achieved on the HES prototype wall is higher than in the horizontal position.Keywords: RCCS, Heater Element System, infrared camera, temperature
Perencanaan Sistem Proteksi Generator dari Putaran Balik di PLTMH Totabuan ARFIANTO, TEGUH; HARIYANTO, NASRUN; SITOHANG, DELFAN TONIUS
ELKOMIKA: Jurnal Teknik Energi Elektrik, Teknik Telekomunikasi, & Teknik Elektronika Vol 6, No 3: Published September 2018
Publisher : Institut Teknologi Nasional, Bandung

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.26760/elkomika.v6i3.436

Abstract

ABSTRAKPada penelitian ini penulis melakukan perhitungan, simulasi dengan aplikasi ETAP 12.6.0 kemudian membandingkan hasil simulasi dengan standar PLN. Pada setting relay daya balik penulis menerapkan standart IEEE C37.102-2006, daya balik generator dengan kapasitas 2 x 2,5 MW adalah 50000 watt dengan waktu tunda relay 10 detik. Sedangkan daya balik untuk generator kapasitas 4 x 0,7 MW adalah 14000 watt dengan waktu tunda relay 10 detik. Hasil yang didapat dari simulasi saat terjadi kenaikan tegangan 110% adalah 0,57 detik dan saat 130% adalah 0,105 detik. Sedangkan untuk setting relay tegangan saat terjadi turun tegangan 50% adalah 0,125 detik dan saat 80% adalah 1,25 detik. Hasil simulasi dengan standar PLN tidak jauh berbeda, waktu yang diterapkan PLN ketika naik tegangan 110% adalah 2 detik dan saat 130% adalah 0,1 detik kemudian untuk turun tegangan 50% adalah 0,1 detik dan saat 80% adalah 1 detik.Kata Kunci: Generator, Daya Balik, Proteksi, Setting, Relay ABSTRACTIn this study the authors perform calculations, simulations with software ETAP 12.6.0 and then compare the results of simulation with standard PLN. On setting power relay writer applying standart IEEE C37.102-2006, generator reverse power capacity 2 x 2.5 MW is 50000 watt with relay time delay 10 second. While reverse power for generator capacity 4 x 0,7 MW is 14000 watt with a 10 second delay time. The results obtained from simulation when there is a 110% increase voltage 0.57 seconds and when 130% is 0.105 seconds. As for the setting of voltage relay when there voltage drop of 50% is 0.125 seconds and when 80% is 1.25 seconds. The result of simulation with PLN standard is not much different, the time applied by PLN when the voltage rise of 110% adds 2 seconds and when 130% is 0.1 seconds later to drop the 50% voltage 0.1 second and 80% is 1 second.Keywords: Generator, Reverse Power, Proteksi, Setting, Relay
Implementasi Sistem IP PBX menggunakan Briker ARYANTA, DWI; DARLIS, ARSYAD RAMADHAN; PRATAMA, ARDHIANSYAH
ELKOMIKA: Jurnal Teknik Energi Elektrik, Teknik Telekomunikasi, & Teknik Elektronika Vol 1, No 2: Published July - December 2013
Publisher : Institut Teknologi Nasional, Bandung

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.26760/elkomika.v1i2.117

Abstract

ABSTRAKVoIP (Voice over Internet Protocol) adalah komunikasi suara jarak jauh yang digunakan melalui jaringan IP. Pada penelitian ini dirancang sistem IP PBX dengan menggunakan teknologi berbasis VoIP. IP PBX adalah perangkat switching komunikasi telepon dan data berbasis teknologi Internet Protocol (IP) yang mengendalikan ekstension telepon analog maupun ekstension IP Phone. Software VirtualBox digunakan dengan tujuan agar lebih memudahkan dalam sistem pengoperasian Linux yang dimana program untuk membuat IP PBX adalah menggunakan Briker yang bekerja pada Operating System Linux 2.6. Setelah proses penginstalan Briker pada Virtualbox dilakukan implementasi jaringan IP PBX. Setelah mengimplementasikan jaringan IP PBX sesuai dengan topologi, kemudian melakukan pengujian success call rate dan analisis Quality of Service (QoS). Pengukuran QoS menggunakan parameter jitter, delay, dan packet loss yang dihasilkan dalam sistem IP PBX ini. Nilai jitter sesama user Briker (baik pada smartphone maupun komputer) mempunyai rata-rata berada pada nilai 16,77 ms. Sedangkan nilai packetloss yang didapat pada saat terdapat pada saat user 1 sebagai pemanggil telepon adalah 0%. Sedangkan persentase packet loss pada saat user 1 sebagai penerima telepon adalah 0,01%. Nilai delay pada saat berkomunikasi antar user berada pada 11,75 ms. Secara keseluruhan nilai yang didapatkan melalui penelitian ini, dimana hasil pengujian parameter-parameter QOS sesuai dengan standar yang telah direkomendasikan oleh ITU dan didapatkan nilai QoS dengan hasil “baik”.Kata Kunci: Briker, VoIP, QoS, IP PBX, Smartphone.ABSTRACTVoIP (Voice over Internet Protocol) is a long-distance voice communications over IP networks are used. In this study, IP PBX systems designed using VoIP -based technologies. IP PBX is a telephone switching device and data communication technology-based Internet Protocol (IP) which controls the analog phone extensions and IP Phone extensions. VirtualBox software is used in order to make it easier for the Linux operating system to create a program which is using briker IP PBX that works on Linux 2.6 Operating System. After the installation process is done briker on Virtualbox IP PBX network implementation. After implementing the IP PBX network according to the topology, and then do a test call success rate and analysis of Quality of Service (QoS). Measurement of QoS parameters using jitter, delay, and packet loss resulting in the IP PBX system. Jitter value briker fellow users (either on a smartphone or computer) has been on the average value of 16.77 ms. While the values obtained packetloss when there is 1 user when a phone caller is 0%. While the percentage of packet loss at user 1 as a telephone receiver is 0.01%. Delay value when communicating between users located at 11.75 ms. Overall value obtained through this study , where the results of testing the QOS parameters in accordance with the standards recommended by the ITU and the QoS values obtained with the results "good".Keywords: Briker, VoIP, QoS, IP PBX, Smartphone.
Penyisipan Citra pada Audio dengan Kode PN Terdistribusi Gaussian BUDIMAN, GELAR; AULIA, SUCI; RAMATRYANA, I NYOMAN APRAZ
ELKOMIKA: Jurnal Teknik Energi Elektrik, Teknik Telekomunikasi, & Teknik Elektronika Vol 7, No 2: Published May 2019
Publisher : Institut Teknologi Nasional, Bandung

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.26760/elkomika.v7i2.209

Abstract

ABSTRAKPada makalah ini, perancangan audio watermarking memanfaatkan kode PN yang terdistribusi Gaussian atau Normal dengan menggunakan citra sebagai watermark yang disisipkan pada audio. Watermark yang berupa citra biner diubah ke dalam vektor 1 dimensi, kemudian dijumlahkan dengan kode PN terdistribusi normal yang disaring dengan filter psikoakustik. Setelah itu, sinyal dikalikan dengan faktor gain α sebelum dijumlahkan dengan host audio untuk mendapatkan watermarked audio. Hasil dari simulasi menunjukkan bahwa sistem memiliki kapasitas watermark yang tinggi pada 689.06 bps, imperseptibilitas yang baik pada SNR>26 dB, dan tahan terhadap serangan LPF mulai frekuensi cut off 6 kHz keatas, serangan Additive Noise mulai 40 dB keatas, resampling pada rate 16 kHz, LSC 1% - 10%, dan kompresi MP3 untuk rate 192 kbps.Kata kunci: Audio Watermarking, Kode PN, distribusi normal, filter sikoakustik ABSTRACTIn this paper, the design of audio watermarking utilizes PN code that is Gaussian or Normal distributed by using the image as a watermark inserted in the audio. The watermark in the form of binary images is converted into a 1-dimensional vector, then summed up with a normally distributed PN code filtered by a psychoacoustic filter. After that, the signal is multiplied by α gain factor before adding it to the audio host to get the watermarked audio. The result of the simulation shows that the system has a high watermark capacity at 689.06 bps, good imperceptibility at SNR> 26 dB, and withstand LPF attacks starting from 6 kHz cut-off frequency and above, Additive Noise attacks from 40 dB up, resampling at 16 kHz , LSC 1% - 10%, and MP3 compression for 192 kbps rate.Keywords: Audio Watermarking, PN code, normal distribution, psychoacoustic filter
Perancangan Prototipe Receiver Beacon Black Box Locator Acoustic 37,5 kHz Pingers RUSTAMAJI, RUSTAMAJI; RAHMIATI, PAULINE; PERMATASARI, SARAH
ELKOMIKA: Jurnal Teknik Energi Elektrik, Teknik Telekomunikasi, & Teknik Elektronika Vol 4, No 1: Published January - June 2016
Publisher : Institut Teknologi Nasional, Bandung

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.26760/elkomika.v4i1.66

Abstract

ABSTRAKKetika suatu pesawat terbang mengalami kecelakaan terjatuh ke dalam air, maka lokasi keberadaannya dapat dideteksi oleh alat yang disebut receiver beacon black box locator acoustic (pingers receiver). Pingers receiver berfungsi untuk menerima sinyal dengan frekuensi 37,5 kHz ± 1 kHz dari pingers transmitter atau Underwater Locator Beacon (ULB) yang berada pada black box pesawat. Dalam penelitian ini dibuat perancangan pingers receiver yang tersusun dari rangkaian Band Pass Filter (BPF), detektor selubung, penguat audio, dan loud speaker. Frekuensi sinyal 37,5 kHz ± 1 kHz yang dikirim oleh pingers transmitter akan diterima oleh pingers receiver, dimana tahap pertama melewati rangkaian Band Pass Filter (BPF) selanjutnya sinyal akan dideteksi oleh detektor selubung untuk mengambil kembali sinyal informasi yang berupa sinyal pulsa dengan lebar pulsa 10 milidetik dan interval 1 detik sebagai sinyal pingers yang nantinya mampu didengar oleh telinga manusia. Berdasarkan perancangan yang telah dibuat, output sinyal yang dihasilkan oleh prototipe pingers receiver tersebut memiliki lebar pulsa 14 milidetik dengan interval 1 detik. Kata kunci: pingers receiver, band pass filter (BPF), detektor selubung, loud speaker.ABSTRACTWhen an aircraft caught in an accident and crashes into the water, its location can be detected using a device called a receiver beacon black box locator acoustic (pingers receiver). The pingers receiver functioned as a reciever signal with 37,5 kHz ± 1 kHz frequency from trnasmitter pingers or Underwater Locator Beacon (ULB) which is on air plane black blox. In this research made design pingers receiver composed of a series of  Band Pass Filter (BPF), envelope detector, audio amplifier, and loud speaker. The signal of 37,5 kHz ± 1 kHz  frequency sent by pingers transmitter will bereceived by pingers receiver, after which the signal will be processed by the Band Pass Filter (BPF) circuit before being detected by envelope detector for take back the signal information which like pulse signal with 10ms width and 1 second interval as pingers signal tha can  be to  be heard by human ear. Based on the  design that  was made, the signal ouput generated by the prototype has a 14 ms width with 1 second interval. Keywords: pingers receiver, band pass filter (BPF), envelope detector, loud speaker.
Analisis Kinerja Jaringan Hybrid Kooperatif Device-to-Device 5G menggunakan Teknik Pemilihan Relay Reaktif AZMI, MUHAMMAD RAUDHI; MELINDA, MELINDA; NASARUDDIN, NASARUDDIN
ELKOMIKA: Jurnal Teknik Energi Elektrik, Teknik Telekomunikasi, & Teknik Elektronika Vol 8, No 1: Published January 2020
Publisher : Institut Teknologi Nasional, Bandung

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.26760/elkomika.v8i1.178

Abstract

ABSTRAK Sistem komunikasi kooperatif device-to-device (D2D) merupakan salah satu strategi peningkatan kecepatan data dan efisiensi energi. Pada sistem kooperatif, mekanisme relay merupakan faktor penting dalam meneruskan informasi. Model jaringan merupakan isu penting untuk meningkatkan kecepatan, kinerja dan efisiensi energi pada sistem. Oleh sebab itu, makalah ini menganalisis kinerja jaringan hybrid kooperatif D2D pada teknologi 5G menggunakan teknik pemilihan relay reaktif atau reactive relay selection (RRS). Beberapa parameter kinerja penting telah simulasikan, seperti model jaringan, SNR, BER dan throughput. Hasil simulasi menunjukkan bahwa jaringan kooperatif hybrid-relay dengan RRS menghasilkan nilai BER yang lebih kecil dan throughput yang lebih tinggi dibandingkan model multi-relay dan multi-hop relay. Dengan demikian, jaringan hybrid-relay dengan pemilihan relay lebih efisien dibandingkan jaringan lainnya. Kata kunci: sistem komunikasi kooperatif, pemilihan relay reaktif, multi-hop, multi-relay, hybrid-relay.  ABSTRACT A device-to-device (D2D) cooperative communication system is one of the strategies to increase data speed and energy efficiency. In a cooperative system, the relay mechanism is an important factor in forwarding information. A network model is an important issue to increase the speed, performance and energy efficiency of the system. Therefore, this paper analyzes the performance of D2D cooperative hybrid networks on 5G technology using reactive relay selection (RRS) techniques. Some important performance parameters have been simulated, such as network models, SNR, BER and throughput. Simulation results show that hybridrelay cooperative networks with RRS produce smaller BER values and higher throughput compared to multi-relay and multi-hop relay models. Thus, hybridrelay networks with relay selection are more efficient than other networks. Keywords: cooperative communication system, reactive relay selection, multihop, multi-relay, hybrid-relay.

Filter by Year

2013 2026


Filter By Issues
All Issue Vol 14, No 1: Published January 2026 Vol 13, No 4: Published November 2025 Vol 13, No 3: Published July 2025 Vol 13, No 2: Published April 2025 Vol 13, No 1: Published January 2025 Vol 12, No 4: Published October 2024 Vol 12, No 3: Published July 2024 Vol 12, No 2: Published April 2024 Vol 12, No 1: Published January 2024 Vol 11, No 4: Published October 2023 Vol 11, No 4 (2023): ELKOMIKA: Jurnal Teknik Energi Elektrik, Teknik Telekomunikasi, & Teknik Elektr Vol 11, No 3: Published July 2023 Vol 11, No 2: Published April 2023 Vol 11, No 1: Published January 2023 Vol 10, No 4: Published October 2022 Vol 10, No 3: Published July 2022 Vol 10, No 2: Published April 2022 Vol 10, No 1: Published January 2022 Vol 9, No 4: Published October 2021 Vol 9, No 3: Published July 2021 Vol 9, No 2: Published April 2021 Vol 9, No 1: Published January 2021 Vol 8, No 3: Published September 2020 Vol 8, No 2: Published May 2020 Vol 8, No 2 (2020): ELKOMIKA: Jurnal Teknik Energi Elektrik, Teknik Telekomunikasi, & Teknik Elektro Vol 8, No 1 (2020): ELKOMIKA Vol 8, No 1: Published January 2020 Vol 7, No 3 (2019): ELKOMIKA Vol 7, No 3: Published September 2019 Vol 7, No 2: Published May 2019 Vol 7, No 2 (2019): ELKOMIKA Vol 7, No 1 (2019): ELKOMIKA Vol 7, No 1: Published January 2019 Vol 6, No 3: Published September 2018 Vol 6, No 3 (2018): ELKOMIKA Vol 6, No 3 (2018): ELKOMIKA Vol 6, No 2 (2018): ELKOMIKA Vol 6, No 2: Published May 2018 Vol 6, No 1: Published January 2018 Vol 6, No 1 (2018): ELKOMIKA Vol 5, No 2: Published July - December 2017 Vol 5, No 2 (2017): ELKOMIKA Vol 5, No 1: Published January - June 2017 Vol 5, No 1 (2017): ELKOMIKA Vol 4, No 2 (2016): ELKOMIKA Vol 4, No 2: Published July - December 2016 Vol 4, No 1 (2016): Jurnal Elkomika Vol 4, No 1: Published January - June 2016 Vol 4, No 1 (2016): ELKOMIKA Vol 3, No 2 (2015): ELKOMIKA Vol 3, No 2 (2015): Jurnal Elkomika Vol 3, No 2: Published July - December 2015 Vol 3, No 1: Published January - June 2015 Vol 3, No 1 (2015): ELKOMIKA Vol 3, No 1 (2015): Jurnal Elkomika Vol 2, No 2 (2014): Jurnal Elkomika Vol 2, No 2 (2014): ELKOMIKA Vol 2, No 2: Published July - December 2014 Vol 2, No 1: Published January - June 2014 Vol 2, No 1 (2014): ELKOMIKA Vol 2, No 1 (2014): Jurnal Elkomika Vol 1, No 2 (2013): ELKOMIKA Vol 1, No 2: Published July - December 2013 Vol 1, No 2 (2013): Jurnal Elkomika Vol 1, No 1 (2013): Jurnal Elkomika Vol 1, No 1 (2013): ELKOMIKA Vol 1, No 1: Published January - June 2013 More Issue