Claim Missing Document
Check
Articles

Found 12 Documents
Search

Rancang Bangun dan Pengujian Mesin Penggiling dan Pengaduk Bumbu Soto Mie Kapasitas 10 kg Candra Irawan; Claudha Alba Pradhana; Ahmad Farhan; Tito Endramawan; Sukroni; Emin Haris
METALIK : Jurnal Manufaktur, Energi, Material Teknik Vol. 4 No. 2 (2025): Metalik: Jurnal Manufaktur, Energi, Material Teknik
Publisher : Universitas Muhammadiyah PROF. DR. HAMKA Fakultas Teknik – Program Studi Teknik Mesin

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.22236/metalik.v4i2.21015

Abstract

Proses pembuatan bumbu Soto Mie Bogor secara manual membutuhkan waktu yang lama, antara 1 hingga 2 jam untuk mengolah 3 kg bumbu, dan mengandalkan tenaga manusia yang besar. Hal ini mengakibatkan pengadukan yang tidak merata serta mempengaruhi kualitas bumbu. Penelitian ini bertujuan untuk merancang dan menguji mesin penggiling dan pengaduk bumbu Soto Mie Bogor dengan kapasitas 10 kg, yang terdiri dari 8 kg bumbu dan 2 kg minyak, guna meningkatkan efisiensi produksi UMKM. Mesin ini menggabungkan fungsi penggilingan dan pengadukan dalam satu unit yang digerakkan oleh motor listrik 0,75 kW dengan sistem transmisi gearbox rasio 1:40. Desain mesin menggunakan perangkat lunak SolidWorks 2021. Hasil pengujian menunjukkan bahwa mesin ini dapat mengurangi waktu pengolahan bumbu menjadi sekitar 1 jam, jauh lebih efisien dibandingkan dengan metode manual yang memakan waktu 3–4 jam. Mesin ini diperkirakan mengonsumsi sekitar 0,75 kWh per hari, dengan biaya listrik bulanan sekitar Rp31.000 jika beroperasi selama satu jam setiap hari. Implementasi mesin ini diharapkan dapat mengurangi kesalahan manusia, meningkatkan kapasitas produksi, dan mengoptimalkan waktu operasional UMKM Soto Mie Bogor.
Mechanical performance of SLA-printed BCC, FCC, and hexagon lattice structures under various layer thicknesses and post-curing times Candra Irawan; Agus Sifa; Tito Endramawan; Dedi Suwandi; Muhammad Luthfi; Emin Haris; Ahmad Farhan; Claudha Alba Pradhana
Jurnal Polimesin Vol 24, No 5 (2026): October
Publisher : Politeknik Negeri Lhokseumawe

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.30811/jpl.v24i5.9936

Abstract

The mechanical performance of stereolithography (SLA)-printed lattice structures is governed by both unit-cell topology and processing parameters. However, previous studies have largely examined lattice topology and SLA processing parameters separately, with limited systematic investigation of their combined effects on manufacturing quality, mechanical performance, and structural efficiency within a unified experimental framework. This study experimentally evaluated three lattice topologies, namely Body-Centered Cubic (BCC), Face-Centered Cubic (FCC), and Hexagonal, combined with layer thicknesses of 0.05, 0.10, and 0.15 mm and post-curing times of 40, 50, and 60 min. Five specimens were tested for each of the nine Taguchi L9 experimental conditions (n = 5), and the responses were analysed using the Signal-to-Noise (S/N) ratio and Analysis of Variance (ANOVA). Manufacturing quality was evaluated from dimensional accuracy and mass, while mechanical performance was assessed through Shore D hardness and tensile, compressive, and flexural tests. Structural efficiency was evaluated using Mass Reduction (MR), Mechanical Performance Retention (MPR), Specific Mechanical Performance (SMP), and Mechanical Performance per Apparent Volume (MPV). The BCC topology exhibited the highest dimensional accuracy, with a strut diameter deviation of 0.60%, whereas Hexagon showed the largest deviation of 7.60%. Layer thickness was the dominant factor affecting hardness, contributing 97.8% of the variation, while lattice topology dominated tensile, compressive, and flexural strength, with contributions of 89.7%, 91.6%, and 55.8%, respectively. FCC provided the highest MPR, SMP, and MPV values, whereas Hexagon achieved the highest mass reduction of 26.50%. Within the investigated parameter ranges, FCC with a 0.05 mm layer thickness and 40–50 min post-curing provided the most favorable overall performance. These results demonstrate that integrating lattice topology, SLA processing parameters, mechanical performance, and structural efficiency provides a comprehensive basis for selecting lightweight lattice configurations.