Article Per Year (5 Year)
p-Index From 2020 - 2025
0
P-Index
This Author published in this journals
All Journal Journal of Engineering and Technological Sciences
S. Subagjo
Chemical Engineering Department, Faculty of Industrial Technology, Institut Teknologi Bandung, Jalan Ganesa No. 10 Bandung 40132
Engineering

Published : 2 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Found 2 Documents
Search

 1 
Dynamic Behavior of Reverse Flow Reactor for Lean Methane Combustion Budhi, Yogi W.; Effendy, M.; Bindar, Yazid; Subagjo, S.
Journal of Engineering and Technological Sciences Vol 46, No 3 (2014)
Publisher : ITB Journal Publisher, LPPM ITB

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (1273.272 KB) | DOI: 10.5614/j.eng.technol.sci.2014.46.3.5

Abstract

The stability of reactor operation for catalytic oxidation of lean CH4 has been investigated through modeling and simulation, particularly the influence of switching time and heat extraction on reverse flow reactor (RFR) performance. A mathematical model of the RFR was developed, based on one-dimensional pseudo-homogeneous model for mass and heat balances, incorporating heat loss through the reactor wall. The configuration of the RFR consisted of inert-catalyst-inert, with or without heat extraction that makes it possible to store the energy released by the exothermic reaction of CH4 oxidation. The objective of this study was to investigate the dynamic behavior of the RFR for lean methane oxidation and to find the optimum condition by exploring a stability analysis of the simple reactor. The optimum criteria were defined in terms of CH4 conversion, CH4 slip, and heat accumulation in the RFR. At a switching time of 100 s, the CH4 conversion reached the maximum value, while the CH4 slip attained its minimum value. The RFR could operate autothermally with positive heat accumulation, i.e. 0.02 J/s. The stability of the RFR in terms of heat accumulation was achieved at a switching time of 100 s.
The Influence of PEG400 and Acetone on Polysulfone Membrane Morphology and Fouling Behaviour Aryanti, P.T.P.; Joscarita, Shelli R.; Wardani, Anita K.; Subagjo, S.; Ariono, Danu; Wenten, I Gede
Journal of Engineering and Technological Sciences Vol 48, No 2 (2016)
Publisher : ITB Journal Publisher, LPPM ITB

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (292.652 KB) | DOI: 10.5614/j.eng.technol.sci.2016.48.2.1

Abstract

Modification of polysulfone ultrafiltration membrane was conducted by blending polysulfone with PEG400 and acetone as additives. The influence of each additive on the resulted membrane morphology and fouling characteristics were investigated. The experimental results showed that the hydrophilicity of the polysulfone membrane was improved by the increase of PEG400 in the polysulfone membrane. The water contact angle of the membrane was decreased from 76.1° to 38.31° when 35 %wt of PEG400 was added into the polysulfone solution, while the water content of the membrane was increased by around 38%. The high concentration of PEG400 in the polysulfone solution led to the formation of longer finger-like cavities in the membrane structure and resulted in a thicker membrane skin layer. The high concentration of PEG400 also contributed to the increase in hydraulic resistance of the membrane due to organic matter fouling. This problem could be minimized by the addition of acetone into the polysulfone solution, which resulted in a lower fouling resistance of organic matter during up to five hours of peat water filtration.
Co-Authors Anita K. Wardani, Anita K. Danu Ariono I Gede Wenten M. Effendy P.T.P. Aryanti, P.T.P. Shelli R. Joscarita, Shelli R. Yazid Bindar Yogi W. Budhi