Claim Missing Document
Check
Articles

Found 28 Documents
Search

Baby Incubator Based on PID Control With Kangaroo Mode (Kangaroo Mode and Humidity) Nur Fildzah Hidayati; Endro Yulianto; Abd Kholiq
Journal of Electronics, Electromedical Engineering, and Medical Informatics Vol 1 No 2 (2019): October
Publisher : Department of Electromedical Engineering, POLTEKKES KEMENKES SURABAYA and IKATEMI

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.35882/jeeemi.v1i2.3

Abstract

Baby Incubator is one of the electromedical equipment used to provide protection to premature babies or low birth weight. Baby care in the baby incubator causes separation of mother and baby. A new innovation in the care of premature babies who bring their babies and mothers closer is Kangaroo Method Management (PMK). Kangaroo method treatment aims to create emotional attachment to the baby, so that the mother will confidently take care. The research and manufacture of this module uses a method of treating baby incubator by adding a reading of the room temperature when the kangaroo mode runs at a setting of 34 ° C - 37 ° C with the effect of room temperature at 18 ° C, 24 ° C, and 30 ° C and setting the humidity control automatically by measuring at a temperature of 32 ° C, then measuring the results immediately. Sensors used to detect temperature are LM35 sensors and sensors used to detect humidity using DHT22. Based on the measurement results obtained uncertainty values ​​on the measurement of humidity 2.1, the measurement of temperature stability can be seen from the results of the graph which shows that the room temperature is not too influential at the temperature of the baby incubator. This study has shown the development of baby incubators to help mothers who have babies born prematurely so that they can have a good bond with how to treat skin to skin. This study has proven that its accuracy is appropriate to be used to stabilize the condition of babies born prematurely and help to treat PMK in some hospitals. In the future, this research can be made and used in small clinics in villages at low costs.
Syringe Pump With Nearly Empty Based Microcontroller Atmega328 Lely Erica Putri; Muhammad Ridha Mak'ruf; Abd Kholiq
Journal of Electronics, Electromedical Engineering, and Medical Informatics Vol 1 No 2 (2019): October
Publisher : Department of Electromedical Engineering, POLTEKKES KEMENKES SURABAYA and IKATEMI

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.35882/jeeemi.v1i2.5

Abstract

Syringe Pump is a tool used to give liquid medicine or food liquid into the patient's body in a certain amount and within a certain period of time on a regular basis. The purpose of this study is to facilitate monitoring of fluid in the syringe so that the hose is not installed continuously when the liquid has run out. The circuit consists of an Atmega328 microcontroller, a motor driver, and an optocoupler sensor. Setting the syringe, volume and flowrate is done at the beginning. To insert liquid, the motor must be run by the way the settings have been done and press the start button. Tools need supply from PLN grids. Calibration is done using IDA 4 Plus. This tool is equipped with the addition of alarms nearly empty and the bolus button. From the measurements taken, at the 20 ml syringe the biggest error occurred at the 5 ml volume point of 0.4% and at the 50 ml syringe the biggest error occurred at the 5 ml volume point of 0.280%.This module can be used according to its function, because the% error is still below the ± 5% standard.
A Modification of Infant Warmer with Monitoring of Oxygen Saturation, Heart Rate and Skin Temperature Muhammad Syahrul Azam Nampira; Abd Kholiq; Lamidi
Journal of Electronics, Electromedical Engineering, and Medical Informatics Vol 3 No 1 (2021): January
Publisher : Department of Electromedical Engineering, POLTEKKES KEMENKES SURABAYA and IKATEMI

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.35882/jeeemi.v3i1.4

Abstract

Full term and premature babies have decreased body temperature by 0.1 ° C-0.3 ° C per minute, infant warmer was developed to provide the effect of heat on the baby as the temperature in the mother's uterus. The purpose of this study is to modify the infant warmer tool by adding parameters SpO2, BPM, and skin sensors. The contribution of this research is that the SpO2, BPM, and skin sensor monitoring systems are very helpful in the therapeutic and healing process using infant warmers. The use of the right sensor and has good quality will produce results and a small error value so it does not exceed the maximum value that is tolerated. The MAX 30100 sensor can detect oxygen saturation in the blood (SpO2) and heart rate (BPM), the DS18B20 temperature sensor can detect temperatures on the surface of the skin or body. Based on the results of measurements on 3 different respondents with 6 times of data retrieval and compared with standard tools the largest error value obtained from SpO2 is 0.68% and the smallest error value is 0.17%, while the largest error value from BPM is 0.76 bpm and the smallest error value is 0.42 bpm, the value of skin temperature error obtained is 0.28% obtained from the measurement of 1 respondent with 6 times of data retrieval and compared with standard tools. The tool is said to be suitable for use because the maximum limit in SpO2 error tolerance is 2% and BPM is 5%. The results of this research can be implemented on infant warmers to improve the monitoring of physiological conditions in patients.
Pemantauan Infus Pump Secara Wireless Menggunakan Modul RF HC-11 Decoriza Kurnia Abadi; Abd. Kholiq; Sumber Sumber; Sari Luthfiyah
Jurnal Teknokes Vol 12 No 2 (2019): September
Publisher : Jurusan Teknik Elektromedik, POLTEKKES KEMENKES Surabaya, Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (444.058 KB)

Abstract

Infuse pump suatu peralatan kedoteran dengankategori life support yang berfungsi untuk memasukan cairan atau obat yang dibutuhkan oleh pasien dengan flow rate ( ml/h) yang terkontrol.Modul ini menggunakan driver motor L298N sebagai pengendali motor stepper. Pemilihan setting infuse pump yaitu setting volume dari pemilihan 100 ml sampai 500 ml dan setting kecepatan dari pemilihan 30 ml/jam, 60 ml/jam, dan 90 ml/jam. Penulis menggunakan mikrokontrollerAtmega 328 sebagai pengontrol tetesan per menit, volume, dan kecepatan Alat ini juga dilengkapi monitoring volume, tpm dan kecepatan pada PC berbasis wireless menggunakan HC-11 sebagai pengiriman dari modul ke PC .Alat ini dilengkapi dengan Lock door.Pengolahan data lajualiranpada IDA dari infus di dapatkan hasil error terendah pada setting 30 ml/jam yaitusebesar -5,97%. Hasil error untuk perhitunganmodul yang tertinggi pada setting 30 ml/jam yaitu sebesar 32% dan manual pada setting 60 yaitu 23%.
Light Curing Portable dengan 3 Mode Penyinaran Riska Dwi Rahma Anggaraini; Endang Dian Setioningsih; Abd. Kholiq; Liliek Soetjiatie
Jurnal Teknokes Vol 12 No 2 (2019): September
Publisher : Jurusan Teknik Elektromedik, POLTEKKES KEMENKES Surabaya, Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (528.815 KB)

Abstract

Light Curing merupakan alat kedokteran gigi yang menghasilkan cahaya tampak dengan panjang gelombang 400-500 nm. Light Curing sendiri digunakan untuk mengeraskan bahan tambal gigi. Penambalan pada gigi tersebut dilakukan karena terjadinya kerusakan pada struktur gigi (Karies). Salah satu bahan tambal gigi untuk mengganti struktur gigi yang hilang yang digunakan saat ini adalah resin komposit. Alat ini akan menyinari resin komposit dengan waktu yang telah ditentukan, Penulis menggunakan Arduino NANO sebagai pengatur waktu pada alat. Proses penyinaram pada alat ini dilengkapi dengan 3 Mode Penyinaran (Stepped, Ramped, Dan Pulse-Delayed) dan juga pengaturan intensitas cahaya untuk mode konvensional. Berdasarkan hasil pengujian dan pengambilan data dengan mengukur kekerasan resin komposit dengan alat Hardness Tester, resin komposit yang di berikan penyinaran dengan waktu 20 detik, 40 detik dan 60 detik dengan ketebalan resin komposit 2mm. Pada alat dengan tambahan 3 mode dan tambahan pemilihan intensitas penyinaran dengan waktu 20 detik belum dapat memenuhi, namun pada penyinaran dengan waktu 40, dan 60 detik sudah dapat memenuhi tingkat kekuatan kunyah manusia yang mampu menahan sebesar 47 Ba. Pada hasil penyinaran 20 detik belum dapat memenuhi, hal ini dapat dipengaruhi oleh beberapa faktor diantaranya spesifikasi LED yang digunakan berbeda, kondisi lingkungan saat pemberian penyinaran pada resin komposit, kurangnya ketelitian saat menyiapkan sample yaitu kurang ratanya permukaan sample, dan ketelitian pembacaan saat pengujian.
Infant Incubator Berbasis Proportional Integral dan Derivative (PID) Dilengkapi Dengan Mode Kanguru Anggraeni Dara Pratiwi; Endro Yulianto; Abd Kholiq
Jurnal Teknokes Vol 12 No 1 (2019): April
Publisher : Jurusan Teknik Elektromedik, POLTEKKES KEMENKES Surabaya, Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (591.785 KB)

Abstract

Infant Incubator merupakan salah satu peralatan elektromedik yang digunakan untuk memberikan perawataan kepada bayi baru lahir berat rendah dengan cara memberikan suhu ruang yang stabil dan pemantauan suhu tubuh bayi. Tujuan dari penelitian ini adalah mengembangkan sistem kontrol suhu ruang Infant Incubator sehingga didapatkan hasil suhu yang stabil. Penelitian dan pembuatan alat menggunakan sensor thermistor untuk suhu kulit bayi dan sensor LM35 untuk suhu ruang Infant Incubator dengan sistem kontrol PID yang dilakukan dengan metode trial and error sampai mendapatkan respon suhu yang optimal pada konstanta proportional (Kp) sebesar 57, konstanta integrator (Ki) sebesar 8 dan konstanta differential (Kd) sebesar 3.2. Berdasarkan hasil pengukuran yang dilakukan dengan INCU Analyzer didapatkan rata – rata error terbesar pada pengaturan suhu 350C sebesar 0.689% dan rata – rata error terkecil pada pengaturan suhu 370C sebesar 0.139%. Pada pengukuran suhu skin terdapat rata – rata pengukuran sebesar 35 0C dengan error sebesar 0.12% terhadap alat pembandingnya. Infant Incubator memiliki kestabilan suhu yang optimal dan pemantauan suhu tubuh bayi yang bermanfaat agar bayi tidak mengalami hipotermi maupun hipertermi.
Rancang Bangun Phantom Sebagai Pengganti Jaringan Tubuh Untuk Mendeteksi Pola Perubahan Suhu Terapi Infra Merah Lamidi Lamidi; Abd Kholiq
Jurnal Teknokes Vol 12 No 2 (2019): September
Publisher : Jurusan Teknik Elektromedik, POLTEKKES KEMENKES Surabaya, Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

Termoterapi merupakan perawatan terapeutik berdasarkan transfer energi panas ke dalam tubuh. Tujuan utama pada bidang klinis terapi ini adalah untuk mencapai hasil pengobatan pada pasien tanpa merusak jaringan tubuh. Pemberian dosis panas terapi infra merah dikaitkan dengan parameter jarak dan waktu penyinaran, untuk menghasilkan dosis panas yang optimal terhadap permukaan kulit belum banyak diungkap secara detail. Sehingga disini pembuatan phantom untuk melakukan penelitian tentang dosis panas pada permukaan kulit tanpa harus melibatkan mahluk hidup secara langsung penting untuk dilakukan.Penelitian ini dapat memberikan gambaran akan paparan panas yang diterima oleh phantom, yang nantinya dapat digunakan sebagai pertimbangan penentuan dosis terkait keselamatan klinis apabila diaplikasikan pada tubuh pasien. Pada penelitian ini menggunakan 2 sensor lm 35 dan Arduino sebagai mikrokontrollernya. Menggunakan delphi sebagai monitoring penyebaran suhu pad 2 sensor ini. Pada delphi juga tersedia fitur untuk save data sehingga mempermudah melakukan pengolahan data hasil monitoring kedua sensor suhu tersebut. Setelah melakukan penelitian diperoleh hasil yang menunjukkan bahwa jarak sangat berpengaruh terhadap peningkatan suhu pada phantom dimana semakin jauh jarak penyinaran maka peningkatan suhu pada phantom semakin kecil.
Infant Warmer Equipped with Digital Weight Scales Muhammad Jundi Al'Aziz; Bambang Guruh Irianto; Abd Kholiq
Jurnal Teknokes Vol 14 No 2 (2021): September
Publisher : Jurusan Teknik Elektromedik, POLTEKKES KEMENKES Surabaya, Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.35882/teknokes.v14i2.4

Abstract

Scales Scales in the world of health are used to measure human body weight such as baby scales. Newborns are very important to be weighed because it is used as a measure of the baby's health indication ranging from 2.4 kg to 4.2 kg. The author makes a tool for this to make it easier for users to weigh with a 7 segment display on the Infant Warmer tool and external calibration. By using a loadcell sensor with a maximum capacity of 5 kg, the loadcell can detect the weight of the load where the voltage generated by the loadcell of 0.7 mV at a load of 1 kg is amplified to 0.62 V by the PSA circuit using the AD620 IC and then processed by Arudino UNO as a microcontroller. The weight results will be displayed on the 7Segment display located on the Infant Warmer tool. In the study, the measured load included a weight of 0 kg to a maximum weight of 5 kg. The measurement of the data results was carried out 5 times each by comparing the modules that had been made with the standard weight, namely (lead). The data from the measurement results of the research module shows that when the weight of the measurement at 1 kg has an error percentage of 0.08%. Measurements at a weight of 2 kg have an error percentage of 0.05%. Measurement of weight 3 kg has a presentation error of 0.01%. Measurements at a weight of 4 kg have a presentation error of 0.02%. And measurements at a weight of 5 kg have an error percentage of 0.04%. Then the data from the measurement results of the research module shows the largest error presentation of 0.08% at a weight of 1 kg. And the data from the measurement results of the research module shows the smallest error presentation of 0.01% at a weight of 3 kg. Making a research module in the form of a scale placed on an infant warmer can make it easier for the wearer.
Monitoring Infusion Pump Via Wireless (Occlusion part) Nisa'ul Sholihah; Abd Kholiq; Sumber Sumber
Indonesian Journal of Electronics, Electromedical Engineering, and Medical Informatics Vol 2 No 1 (2020): February
Publisher : Department of electromedical engineering, Health Polytechnic of Surabaya, Ministry of Health Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.35882/ijeeemi.v2i1.7

Abstract

Infuse pump is a medical equipment which is design to control and regulate the administration of intravenous fluids in the treatment.. This module uses the L298N motor driver as a stepper motor controller. The choice of the infuse pump setting is the volume setting from 100 ml to 500 ml and the speed setting of 30 ml / hour, 60 ml / hour, and 90 ml / hour. The author uses the Atmega 328 microcontroller as a droplet controller per minute, volume and speed. Occlusion in this device is in the detector of the droplets that are alerted in the presence of a sound buzzer. This tool is also equipped with monitoring volume, tpm and speed on a wireless-based PC using HC-11 as a transmission from module to PC. This tool is equipped with oclusion. The flow rate data processing in IDA from infusion got the highest error result at the setting of 30 ml / hour which was equal to 5.97%. the highest error for the calculation of droplets in the module is the setting of 30 ml / hour which is equal to 32% and manually at setting 60 which is 23%.
A Low Cost Baby Incubator Design Equipped with Vital Sign Parameters Lamidi Lamidi; Abd Kholiq; Muslim Ali
Indonesian Journal of Electronics, Electromedical Engineering, and Medical Informatics Vol 3 No 2 (2021): May
Publisher : Department of electromedical engineering, Health Polytechnic of Surabaya, Ministry of Health Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.35882/ijeeemi.v3i2.3

Abstract

A baby incubator is a heating device for premature babies so that the baby's temperature matches the temperature in the mother's womb. Premature babies are babies born in abnormal conditions where the baby's body size is below average or the gestational age has not reached 9 months. The aim of this study was to create a compact system at a low cost in an infant incubator. Apart from stabilizing the temperature, it can also calculate the premature baby's heart rate and oxygen saturation value. The contribution of the system being built can detect the early symptoms of congenital abnormalities so that abnormalities detection becomes more practical. The temperature stability in this system uses a threshold system, where the sensor readings are compared with the set point value. Meanwhile, the SpO2 system uses a finger sensor attached to the baby's finger to detect oxygen saturation and heart rate. The signal from the sensor is processed in a signal conditioning circuit consisting of an astable circuit, filter and amplifier, LPF, and demultiplexer. Based on the results of testing and measurement, the difference produced by this tool is only 0.13 - 0.182 ° C. The biggest error in the system is 0.517%. Measurement of skin temperature was carried out on 10 respondents with an average value of 34.825 ° C. so that the difference generated from this tool is only 0.175 ° C, the difference on the Humidity parameter is 0.21%. The average BPM reading of respondent 1 was 81 beats per minute and the average SpO2 value was 97%. The average BPM reading of respondent 2 was 83 beats per minute and the average SpO2 value was 98%. You can see that the module with the Arduino control system can work automatically and is able to adjust the stability of the baby incubator according to the settings. In addition, the BPM and SpO2 systems are within tolerance so they can be used for patient measurements