Claim Missing Document
Check
Articles

Found 14 Documents
Search

The Influence Of Work Surface Roughness Caused By Fraising Machined With HSS Chies Aljufri, Aljufri; Rizki, Muhammad Nuzan; Akmal, Syarifah; Mutia, Sri; Rambe, Farhan Wafi
Journal of Applied Sciences and Advanced Technology Vol 6, No 2 (2023): Journal of Applied Sciences and Advanced Technology
Publisher : Faculty of Engineering Universitas Muhammadiyah Jakarta

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.24853/jasat.6.2.49-56

Abstract

The development of production techniques is required to produce good products that have standards for the products produced, both in terms of profile shape, size precision, surface roughness, hardness, material flexibility, and others that comply with standards. The surface roughness of a product can affect its functions, such as its level of precision and ability to accept loads. This research aims to find out how much influence cutting speed and depth of cut have on surface roughness with variations in cutting speed parameters of 21 meters/minute and 26 meters/minute and for AISI 4140 steel cutting speed parameters of 12 meters/minute and 17 meters/minute and cutting depths of 0.1 mm and 0.3 mm on four types of steel with End Mill cutting blades made from High-Speed Steel with a total of 4 flute cutting blades. Next, surface roughness testing and analysis of variance were carried out to determine the influence of parameters on surface roughness. The results obtained were that the largest average surface roughness, namely Ra = 5.33 µm, occurred on AISI 4140 steel at a cutting speed of 12 m/min with a cutting depth of 0.3 mm. Meanwhile, the smallest average surface roughness, namely Ra = 0.91 µm, occurred on AISI 1045 steel at a cutting speed of 21 m/min with a cutting depth of 0.1 mm. Next, an analysis of the variance method was also carried out with the following results: cutting speed only affected S45C steel because the value of Fcount>Ftable (13.18107506 > 5.32). The depth of cut does not have a significant effect on surface roughness on all types of steel because of the comparison results Fcount<Ftable. The interaction of cutting speed and cutting depth does not affect surface roughness because the comparison shows that Fcount <Ftable for all types of steel.
Pengaruh Surface Roughnes Pada Material AISI 1045 dan AISI 4140 Akibat Proses Pemesinan Bubut Azhari, Wafiq; Aljufri, Aljufri; Rahman, Abdul; Putra, Reza; Akmal, Syarifah
Malikussaleh Journal of Mechanical Science and Technology Vol 7, No 1 (2023): Malikussaleh Journal of Mechanical Science and Technology
Publisher : Malikussaleh University

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.29103/mjmst.v7i1.12448

Abstract

Lathe machining is one type of conventional machine tool used for cutting/filling workpieces which is done by making an incision on the workpiece where the tool is moved translationally and parallel to the axis of the rotating workpiece. The result of the components of the turning process that is commonly done is surface roughness which is influenced by tool cutting angle, feeding speed, cutting speed, depth of cut. This study was conducted to determine how much influence the speed of feeding and depth of feeding on AISI 1045 steel and AISI 4140 steel materials used in shafts, conecting roads, gears with carbide chisels. With Vc=140 m/min, Vc=150 m/min, Vc=170 m/min, and Vc=180 m/min, and knowing the surface roughness of the workpiece using a carbide tool.  From the results of research on AISI 1045 and AISI 4140 steel for cutting along 50 mm with engine speed 1200 rpm and cutting depth 0.3 mm, as well as the cutting speed used Vc=140 m/min, Vc=150 m/min, Vc=170 m/min and Vc=180 m/min and the initial cutting distance of 4 mm, the time needed is 1,125 minutes. For the surface roughness value of AISI 1045 steel material and AISI 4140 steel has four variations in lathe feeding speed in this study, which in each variation has a different surface roughness value, the smallest surface roughness value is AISI 4140 steel with a feeding speed vc = 180 m / min surface roughness value of 0.705 μm compared to AISI 1045 steel material. This is due to the greater the movement of the feeding speed of feeding, the smaller the value of the surface roughness of the material
ANALISIS PENENTUAN HARGA JUAL PRODUK SIRUP DENGAN MENGGUNAKAN METODE TARGET PROFIT PRICING Bakhtiar, Bakhtiar; Akmal, syarifah
Sisfo: Jurnal Ilmiah Sistem Informasi Vol. 5 No. 2 (2021): Sisfo: Jurnal Ilmiah Sistem Informasi, Oktober 2021
Publisher : Universitas Malikussaleh

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.29103/sisfo.v5i2.6237

Abstract

UD Nira Della yang terletak di kampung Glumpang Sulu Timur, kecamatan Dewantara, kabupaten Aceh Utara merupakan perusahaan UMKM yang bergerak dalam bidang pembuatan Sirup. Sirup yang dihasilkan beraneka rasa, mulai dari rasa pisang ambon, nanas, kopi, melon, leci, jeruk, dan rasa citrom. Dari kesemua rasa tersebut rasa paling diminati adalah rasa pisang ambon. Dalam perbulan UD. Nira Della memproduksi sebanyak 4800 botol, dimana rasa pisang ambon diproduksi sebanyak 3000 botol dan ke enam rasa yang lainnya diproduksi sebanyak 1800 botol, dangan harga jual per botolnya sebesar Rp 5.000. Selama ini UD. Nira Della menerapkan cara konvensional (tradisioanal), hanya berdasarkan perkiraan dalam menentukan harga jual produknya. Metode tersebut tidak selalu tepat digunakan dalam setiap proses negosiasi dengan konsumen, karena dengan menggunakan cara konvensioanal (tradisional) perusahaan tidak dapat menentukan harga jual sebenarnya dan kepastian laba yang diterima oleh perusahaan. Salah satu metode yang digunakan untuk menetukan harga jual produk adalah dengan menggunakan metode target profit Pricing, yang merupakan salah satu metode penentuan harga jual per unit yang memperhitungkan seluruh pengeluaran biaya dengan laba yang telah diperhitungkan dan telah ditargetkan perusahaan melalui penentuan biaya pokok produksi yang dibagi ke dalam biaya variabel dan biaya tetap. Harga Rp. 5.000/botol sirup yang ditetapkan oleh UD. Nira Della, tanpa dilakukan perhitungan secara terperinci terhadap semua biaya pokok produksi dan biaya operasional. Maka berdasarkan hasil perhitungan metode target profit pricing, harga pokok produk diperoleh sebesar Rp 4.695 per unit dan harga jual produk sebesar Rp 5.869 per unit, harga inilah yang seharusnya menjadi harga ekonomi perusahaan.Yanuardi, M. D. W. I., Novirani, D. W. I., & Adianto, H. (2014). Penetapan Harga Jual Batu Bata pada CV.X dengan Menggunakan Metode Target Profit Pricing. 02(03), 13-24.
Solar Energy Management in Electricity Load Application of Household Room Based on IoT Akmal, Syarifah; Meliala, Selamat; Amani, Yasir; Jalil, Saifuddin Muhammad
Journal of Renewable Energy, Electrical, and Computer Engineering Vol. 4 No. 1 (2024): March 2024
Publisher : Institute for Research and Community Service (LPPM), Universitas Malikussaleh, Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.29103/jreece.v4i1.13425

Abstract

Currently using electrical energy is very large and electrical energy security continues to be studied by government. Developments starts from using and managing of renewable energy sources. Energy sources will not be run out. One of which is using heat energy from sunlight. Using The use of the concept of renewable energy utilization strategy is still 17%. The energy management method is to use a smart system where if the room is during the day, the LDR sensor will signal to the microcontroller so that the room lights will turn off and if there is heat the DHT22 sensor detects the room temperature of 300 C. Then the fan turns on and cools the room so that it will cool down and the load that is not needed by the grid will not function so that energy consumption will be reduced according to calculated needs. This working system is based on IOT derived from ESP 8266 to store solar energy consumed by the house room. The smart method used in the research is to place 3 DHT22 sensors for optimal heat temperature. Average temperature sensor data, LDR data is stored in the data logger in the form of xls files on Gdrive. xls files then for 15 days. From the results of the date per 15 days on 13-11-2023, the design obtained an average temperature of 30.90 with a consumption of 5.83 kWH at a cost of 7882.16 rupiah.
Usulan Perbaikan Layanan dengan Metode Dineserv dan Improvement Gap Analyisis (LGA) di Cafe “Coffee Break Sangrai” Bireuen Adriansyah, Dziki; Akmal, Syarifah; Meutia, Sri
Innovative: Journal Of Social Science Research Vol. 4 No. 6 (2024): Innovative: Journal Of Social Science Research
Publisher : Universitas Pahlawan Tuanku Tambusai

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.31004/innovative.v4i6.17078

Abstract

Penelitian ini bertujuan untuk mengusulkan perbaikan layanan di Kafe Coffee Break Sangrai, Bireuen, dengan menggunakan metode DINESERV dan Improvement Gap Analysis (IGA). Berdasarkan analisis terhadap 24 atribut layanan yang dibagi dalam lima dimensi DINESERV Tangible (Bukti Fisik), Reliability (Kehandalan), Responsiveness (Ketanggapan), Assurance (Jaminan), dan Empathy (Empati) ditemukan beberapa atribut yang perlu perbaikan untuk meningkatkan kepuasan pelanggan. Atribut prioritas perbaikan, yang teridentifikasi melalui Kuadran I dalam Diagram Kartesius, mencakup "Mempunyai tempat yang nyaman dan bersih" (T2), "Mempunyai toilet yang bersih" (T7), "Karyawan kafe yang tanggap" (Rs1), dan "Selalu mementingkan kepentingan pelanggan" (E4). Berdasarkan hasil ini, usulan perbaikan layanan yang dapat dilakukan meliputi penerapan SOP kebersihan dan keamanan, pembuatan daftar regu piket toilet, penambahan supervisor untuk pengecekan toilet, penambahan karyawan di kafe, serta pelatihan bagi karyawan. Dengan implementasi perbaikan tersebut, diharapkan dapat meningkatkan kualitas layanan dan kepuasan pelanggan di Kafe Coffee Break Sangrai.
STANDAR OPERASIONAL PROSEDUR PENGEMBANGAN PROTOTIPE PENGERING IKAN KAYU SISTEM KONTROL DUAL ENERGI Muhammad Jalil, Saifuddin; Meliala, Selamat; Akmal, Syarifah; Muhibuddin, Muhibuddin; Fatahillah, Fatahillah; Johari, Johari
Jurnal Malikussaleh Mengabdi Vol. 3 No. 2 (2024): Jurnal Malikussaleh Mengabdi, Oktober 2024
Publisher : LPPM Universitas Malikussaleh

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.29103/jmm.v3i2.20256

Abstract

Undang-Undang Republik Indonesia Nomor 18 Tahun 2012 tentang pangan. Pembangunan Nasional merupakan pencerminan kehendak seluruh rakyat untuk terus-menerus meningkatkan kemakmuran dan kesejahteraannya secara adil dan merata dalam segala aspek kehidupan yang dilakukan secara terpadu, terarah, dan berkelanjutan dalam rangka mewujudkan suatu masyarakat yang adil dan makmur, baik material maupun spiritual berdasarkan Pancasila dan Undang-Undang Dasar Negara Republik Indonesia Tahun 1945. Pangan merupakan kebutuhan dasar manusia yang paling utama dan pemenuhannya merupakan bagian dari hak asasi setiap rakyat Indonesia. Pangan harus senantiasa tersedia secara cukup, aman, bermutu, bergizi, dan beragam dengan harga yang terjangkau oleh daya beli masyarakat, serta tidak bertentangan dengan agama, keyakinan, dan budaya masyarakat. Untuk mencapai semua itu, perlu diselenggarakan suatu sistem ketahanan pangan yang memberikan pelindungan, baik bagi pihak yang memproduksi maupun yang mengonsumsi pangan. Penyelenggaraan pangan dan pengolahan hasil perikanan memegang peranan penting dalam kegiatan pascapanen, mengingat hasil perikanan merupakan komoditi yang sifatnya mudah rusak (perishable goods). Maka perlu dilakukan kegiatan penyuluhan pelaksanaan sosialisasi pengeringan pada ikan dilakukan dengan proses pengeringan Standar Operasional Prosedur Pengembangan Prototipe Pengering Ikan Kayu Sistem Kontrol Dual Energi. Sosialisasi ini telah dilaksanakan di gampong Blang Pulo Kecamatan Muara Satu Kota Lhoksemawe sebagai salah satu bentuk kegiatan pengabdian kepada masyarakat dalam mengemban amanat Tri Darma Perguruan Tinggi. Penyuluhan ini merupakan bukti partisipasi dosen dan masyarakat dalam meningkatkan dan membudayakan aktivitas pengeringan pada ikan dilakukan dengan proses pengeringan Standar Operasional Prosedur Pengembangan Prototipe Pengering Ikan Kayu Sistem Kontrol Dual Energi. Pengabdian ini diharapkan dapat meningkakan cara pandang dan wawasan masyarakat dalam mengurangikesalahan dalam melakukan pengeringan ikan kayu. Kegiatan ini dapat memberikan dampak yang luar biasa bagi kesehatan dan keselamatan hidup, dan  jika salah dalam melakukannya dapat menurunkan ketahanan kesehatan tubuh,  sehingga mengakibatkan kerugian bagi kesehatan masyarakat  itu sendiri. Pengabdian ini yang diharapkan pada masyarakat yaitu dapat melaksanakanstandar operasional prosedur pengembangan prototipe pengering ikan kayu sistem kontrol dual energi
Workload Measurement Using the Cardiovascular Load Method and Defense Research Agency Workload Scale Kurniawan, Dicky; Akmal, Syarifah; Sayuti, Muhammad
International Journal of Engineering, Science and Information Technology Vol 4, No 4 (2024)
Publisher : Malikussaleh University, Aceh, Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.52088/ijesty.v4i4.608

Abstract

Workload is a collection of tasks set to be completed within a specific time. The workload can be broken down into "qualitative" (too much or too little) or "quantitative" (too much or too little), which occurs when people are unable to complete tasks or if they do not utilize the abilities they have in achieving a particular job. This study aimed to determine the workload of workers engaged in the sale of fresh or cut chicken meat. Cardiovascular Load is an estimate to determine the classification of workload based on the increase in work pulse compared to the maximum heart rate. The Defense Research Agency Workload Scale (DRAWS) method is a multidimensional technique that involves participants through subjective questions and assessments consisting of four workload dimensions: input demand, central demand, output demand, and time pressure. The results showed that the workload pulse using Cardiovascular Load, the level of fatigue based on workload obtained at the chicken slaughter station by worker 1 was 44.77%, and worker 2 was 41.11% with the category of improvement needed. At the chicken cleaning station, worker 1 was 44.13%, and worker 2 was 47.43%, with the category of needed improvement. At the chicken cutting station, worker 1 was 43.73%, and worker 2 was 45.85%, with the category of needed improvement. The study's DRAWS method results showed that at the chicken slaughtering station, worker 1 was 84.25%, and worker 2 was 87.05% with the overload category. At the chicken cleaning station, worker 1 was 86.75%, and worker 2 was 84.20% with the overload category. At the chicken cutting station, worker 1 was 85.75%, and worker 2 was 81.30%, with the overload category. This means that six respondents felt a high mental burden, so improvements are needed to reduce the impact of the cognitive workload of workers. The upgrades provided include the provision of chairs around the work area, especially at the chicken slaughtering station, so that workers can sit and rest for a moment to reduce the physical workload experienced by workers.
Utilization of Waste Paper as Fiber for Motorcycle Fender Manufacturing Raw Materials Aljufri, Aljufri; Riskan, Ardi; Rizki, Muhammad Nuzan; Putra, Reza; Akmal, Syarifah
Jurnal Teknologi Vol 17, No 1 (2025): Jurnal Teknologi
Publisher : Fakultas Teknik Universitas Muhammadiyah Jakarta

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.24853/jurtek.17.1.23-30

Abstract

The selection of paper as the main material for making composites in this study is driven by several considerations. HVS paper is produced by factories with the main raw material being wood. Besides, the use of HVS paper as a fiber for composites offers the potential to reduce industrial waste and reduce dependence on conventional raw materials. The purpose of this study was to determine the effect of variations in the volume fraction of HVS pulp fiber on the mechanical properties of the specimen surface and hardness test to determine the use of HVS pulp composites as raw material for making motorcycle fenders. The benefits of this research provide information for the manufacturing industry in developing innovative composite materials, offering sustainable alternatives that are environmentally friendly, increasing the use value of HVS paper processing, which has only been used as waste. From the results of the research conducted, the results obtained with the value: the hardness of the specimen with a volume fraction variation of 70% fiber has the highest average hardness value of 11.5 kg/mm2, and the variation of the volume fraction of 50% fiber has the lowest average hardness value of 8.6 kg/mm2, which has a difference of 2.9 kg/mm2 with a volume fraction variation of 70% fiber. The highest impact price value is obtained at a 70% pulp volume fraction with an average impact price of 0.0402 J/mm², while the lowest pulp composite impact price is at the volume fraction of 70% fiber. 50% pulp with an impact price of 0.0263 J/mm². The increase in hardness and impact resistance with increasing pulp volume explains that this composite can be an alternative material for application on motorcycle fenders.
Optimasi Pengendalian Persediaan Produk Sabun Batang Dengan Metode Min-Max Di PT. Jampalan Baru Asahan Meutia, Sri; Fatimah, Fatimah; Susanti, Sartini; Akmal, Syarifah
Jurnal Industri Samudra Vol 6 No 1 (2025): Jurnal Industri Samudra
Publisher : Program Studi Teknik Industri, Fakultas Teknik. Universitas Samudra

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.55377/jis.v6i1.11516

Abstract

PT. Jampalan Baru merupakan salah satu perusahaan yang bergerak dibidang industri sabun. Permasalahan pada perusahaan adalah kelebihan persediaan produk sabun batang (over stock). Over stock pada PT. Jampalan Baru disebabkan oleh faktor produksi yang dilakukan secara terus menerus sehingga persediaan produk sabun batang menumpuk digudang dan menyebabkan kelebihan persediaan. Permasalahan tersebut menuntut perusahaan untuk mempunyai sistem pengelolaan persediaan yang baik agar persediaan sabun tidak kelebihan dan tetap optimal. Penelitian ini bertujuan mendapatkan sebuah model untuk perusahaan dalam melakukan perencanaan produksi dan pengendalian persediaan produk sabun batang di PT. Jampalan Baru Asahan. Metode yang dapat digunakan yaitu Metode Min-Max. Metode Min-Max merupakan metode pengendalian persediaan yang didasarkan atas asumsi bahwa apabila persediaan telah melewati batas-batas minimum dan mendekati batas dari persediaan pengaman, maka harus dilakukan produksi kembali, terdapat 2 batas dalam metode persediaan Min–Max, yaitu batas minimum level produksi kembali dan batas maksimum sebagai batas maksimal perusahaan untuk memenuhi kebutuhan persediaan produk. Hasil dari perhitungan untuk perencanaan pengendalian persediaan pada produk sabun batang PKS Kuning didapatkan safety stock sebanyak 2.691 Pack, minimum stock sebanyak 14.352 Pack, maximum stock sebanyak 26.013 Pack, jumlah produksi sebesar 23.322 Pack, titik produksi kembali sebesar 14.352 Pack dan frekuensi produksi dalam setahun sebanyak 26 kali atau 14 hari sekali. Untuk produk sabun batang Bintang Hijau didapatkan safety stock sebanyak 1.296 Pack, minimum stock sebanyak 4.784 Pack, maximum stock sebanyak 8.272 Pack, jumlah produksi sebesar 6.977 Pack, titik produksi kembali sebesar 4.784 Pack dan frekuensi produksi dalam setahun sebanyak 26 kali atau 14 hari sekali.
Penghijauan dan Pelestarian Lingkungan Pekarangan Masjid Pante Baro Gani, Subhan A; Sofyan, Diana Khairani; Bakhtiar, Bakhtiar; Erliana, Cut Ita; Akmal, Syarifah; Dafrina , Armelia
Jurnal Pengabdian kepada Masyarakat Nusantara Vol. 4 No. 4 (2023): Jurnal Pengabdian kepada Masyarakat Nusantara (JPkMN)
Publisher : Lembaga Dongan Dosen

Show Abstract | Download Original | Original Source | Check in Google Scholar

Abstract

Masjid Jamik Pante Baro adalah Masjid yang terletak di kecamatan peusangan siblah krueng, Bireuen, Aceh Utara, yang didirikan pada tahun 2010. Masjid ini merupakan Masjid yang letaknya sangat strategis di kota tersebut. Hal ini dikarenakan lokasi Masjid terletak di pinggir jalan dan memudahkan pengunjung dari berbagai jenis wilayah untuk dapat masuk. Salah satu daya tarik Masjid ini adalah arsitekturnya, yang mencerminkan bentuk khas tradisi Aceh dan jelas merupakan ciri khas arsitektur Masjid di daerah tersebut, tetapi sangat disayangkan sekali bahwa kelestarian Masjid tersebut belum terlihat jelas, hal ini dikarenakan belum adanya tanaman yang ditanam disekitar Masjid. Dengan luas tanah Masjid yaitu 5000 m2 dan bangunan Masjid 616 m2 dengan luas pekarangan 4384 m2, Masjid ini cocok untuk dilakukan kegiatan penghijauan, khususnya penanaman pohon. 30 batang pohon kelapa hibrida, 4 (empat) pohon kurma, 4 (empat) pohon alpukat, dan 3 (tiga) pohon mangga telah diteliti dan cocok untuk ditanam diperkarangan Masjid. Dengan memanfaatkan ruang kosong di pelataran Masjid, tujuan secara umum adalah untuk mengurangi polusi udara dan melakukan penghijauan. Tujuan khususnya adalah penanaman pohon di sekitar Masjid. Ini akan menjaga lingkungan tetap asri dan memungkinkan orang di depan Masjid untuk dapat memanfaatkan hasil tanaman atau buah lokal tersebut. Kegiatan menanam pohon buah di lingkungan Masjid ini diharapkan menjadi tradisi baru dan menghasilkan nilai ekonomi. Hasil yang diperoleh pada kegiatan penanaman pohon bibit pohon kelapa hibrida, bibit mangga, alpukat dan kurma yang sudah di tanam dan sudah mulai tumbuh.