Garuda - Garba Rujukan Digital

Evaluasi terhadap Stimulan Ethephon dalam Penyadapan Pinus merkusii (Evaluation on Ethephon Stimulant to Pinus merkusii Tapping) Lukmandaru, Ganis; Sunarta, Sigit; Listyanto, Tomy; Kasmudjo, Kasmudjo; Pujiarti, Rini; Widyorini, Ragil
Jurnal Ilmu dan Teknologi Kayu Tropis Vol 16, No 2 (2018): Jurnal Ilmu dan Teknologi Kayu Tropis
Publisher : Jurnal Ilmu dan Teknologi Kayu Tropis

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (38.454 KB)

The aim of this study was to find out the effect of Ethephon, an ethylene releasing compound, in a combination with sulfuric acid resin production Pinus merkusii. The tested stimulants were ETRAT; SR4; 20% sulfuric acid; 20% sulfuric acid - Ethephon 2%; 3.3% sulfuric acid – 4.1% Ethephon; and sulfuric acid – 8.3% Ethephon. Trees without stimulant spraying were the controls. The results showed that for daily production, the first-day observation gave the highest value but decreased drastically after second-day observation in a varied degree depent on the stimulants. On the basis of accumulated production, the addition of Ethephon in a high or low level of sulfuric acid concentration exhibited significantly higher resin production compared to that of ETRAT; SR4; and 20% sulfuric acid stimulants as well as control trees. It increased resin production by 98.0-150.6% compared to control trees in class age of VII and increased by 140.9-227.1% in class age of IV stands. Moderate significant correlations (r=0.65) were observed between the values of resin production and tree diameter (controls) as well as between the values of resin production and tree diameter of trees treated by sulfuric acid stimulants (r=0.65-0.82).Keywords : class age, ethylene, quarre, resin production, tree diameter

Dimensional Stability and Characteristics of Modified Young Teak (Tectona grandis L.f.) Wood with PEG-1000 Tomy Listyanto; Muhammad Navis Rofii; Keisuke Ando; Nobuaki Hattori
Wood Research Journal Vol 6, No 1 (2015): Wood Research Journal
Publisher : Masyarakat Peneliti Kayu Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.51850/wrj.2015.6.1.14-20

The aim of this study was to investigate the effect of wood modification with polyethylene glycol (PEG)-1000 at five concentrations to improve dimensional stability, drying, machining and finishing characteristics of young teak wood. A total of 12 samples for each treatment was prepared to measure an Anti Shrink Efficiency (ASE), as a parameter of dimensional stability and its drying characteristics. Six samples for each treatment were prepared to evaluate machining and finishing characteristics. PEG-1000 with five concentration levels of 20%, 30%, 40%, 50% and 60% were impregnated to modify the samples, except control. Afterward, all samples were kiln dried to gain 12% moisture content. ASE was determined by comparing shrinkage percentage of treated sample with those of untreated one. Warping and surface checks were measured as drying characteristics and machining test was conducted in accordance to ASTM D1666-2004. After coating with a nitrocellulose system, surface quality were evaluated by conducting cross-cut test (ASTM D3359), coin test, delamination test (SNI 01-5008.2-1999b) and glossyness test (SNI-06-6052-1999a). Result shows that dimensional stability of impregnated samples with concentration of 30~60% was successfully improved, with ASE of 52~62%. All treated samples demonstrated good drying characteristics and defect-free areas which were more than 90% under machining test. Surface evaluation by delamination test, glossyness test, and coin test indicated that all impregnated samples were well coated by a nitrocellulose system. However, only impregnated samples in concentration of 20% and 30% showed a good result in cross-cut test. Impregnation with PEG-1000 in concentration of 30% is recommended to modify young teak wood.

Extractive Content and Colour Properties of 11-Year-Old Superior Teak Wood Ganis Lukmandaru; Alfian Nur Falaah; Tomy Listyanto; Dian Rodiana
Wood Research Journal Vol 12, No 1 (2021): Wood Research Journal
Publisher : Masyarakat Peneliti Kayu Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.51850/wrj.2021.12.1.10-17

There is a lack of understanding about the properties of fast-growing teak trees harvested in young stage. Superior teak woods (11 years, 5 trees) grown in Pemalang FMU were assessed in vertical and radial positions for its extractive contents and colour properties. Extractions were conducted using a sequence of toluene, ethanol, and hot water. The color evaluation was performed using CIEL*a*b*’s chromaticity system. Toluene-, ethanol-, hot-water-, and total extractive contents ranged between 1.16~5.00%; 0.29~1,04%, and 0.98~2.35%, and 4.03~7.31%, respectively. For color properties, the brightness (L*), redness (a*), and yellowness (b*) indices ranged from 49.50~57.42, 6.08~10.81, and 20.47~25.74, espectively.Toluene- and total extractive contents were greater in heartwood than in sapwood, while the reverse occurred for the hot-water extractive content. Toluene- and total extractive contents were higher in outer heartwood than in inner heartwood. With regard to colour properties, L* and a* values were significantly differed between sapwood and heartwood. Vertical stem analysis of samples obtained at bottom, center, and top showed the toluene extractive content, total extractive content, and a* levels of center part of the tree were found to be lower than other parts. The L* were negatively correlated with extractive contents, with the highest correlation degree (-0.83**) being observed in the total extractive content in the heartwood. It is also noticed that superior teak wood wood was less darker and extractive contents than the heartwood control of a 72-year-old tree. Therefore, the properties measured in the present work might be related with natural durability of the woods.

Relationship between Wood Properties and Developed Drying Schedule of Inferior Teak (Tectona grandis L.F) and Mahogany (Swietenia macrophylla King) Tomy Listyanto; Ganis Lukmandaru; Candra Pramadya; Dwi Siswanto; Nobuaki Hattori
Wood Research Journal Vol 1, No 2 (2010): Wood Research Journal
Publisher : Masyarakat Peneliti Kayu Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.51850/wrj.2010.1.2.83-88

Development of drying schedule has been a critical issue on a drying process concerning the changing of material condition, especially in Java. Established drying schedule used to be purposed for a high quality timber. The aims of this study were to develop drying schedule of inferior teak and mahogany, and to analyze the relationship between the drying schedule and its wood properties.The specimens were taken from 25 years old teak and 20 years-old mahogany. Wood density, sapwood percentage and extractive contents were determined as wood properties. Four types of specimen’s dimensions (25 x 30 mm; 25 x 50 mm; 25 x 100 mm; and 50 x 50 mm) were dried in the oven with temperature of 103⁰C until reach oven dried conditions. Levels of checks, collapse, and honeycomb were observed to develop drying schedule. A Chi square analysis was used to analyze the relationship between wood properties and the drying schedule.The results showed that there were four types of drying schedule are applicable for teak and five types for mahogany. The most recommended schedule for teak sample was the schedule with an initial temperature (IT) was 70⁰C, relative humidity (RH) was 71%, and the final temperature (FT) was 90⁰C, while the mahogany wood was the schedule with an IT 60⁰C, RH 81%, and the FT 85⁰C, respectively. Chi square analysis indicated that the mahogany lumber dimension was significantly related to the schedule development while specific gravity, heartwood percentage, and extractive content had no significant relationship with the drying schedule development.

Chemical Properties of 15-year-old Teak (Tectona grandis L.f) from Different Seed Sources Ganis Lukmandaru; Pormando Manalu; Tomy Listyanto; Denny Irawati; Rini Pujiarti; Fanny Hidayati; Dian Rodiana
Wood Research Journal Vol 7, No 1 (2016): Wood Research Journal
Publisher : Masyarakat Peneliti Kayu Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.51850/wrj.2016.7.1.6-12

Fifteen year-old teak wood samples planted in Ciamis FMU (Perhutani Enterprise) were evaluated for their chemical properties. Three seed sources such as conventional seed, clone, and superior wood and radial positions namely sapwood, outer heartwood, and inner heartwood were the observed factors. The specimens were taken from the bottom parts of their sources. Completely randomized design was used. Cell wall components were analyzed by various gravimetric methods.Analysis of variance and Duncan’s test were performed for data analysis. The results showed that no significant difference in the quantity of cell wall components (cellulose, hemicellulose, and lignin), extractives (ethanol-toluene and hot-water solubles), ash, and silica content among the seed sources. Superior teakwood or Jati Plus Perhutani, which has the highest growth rate (2.1~3.6 cm/year) among others, showed a comparative higher average pH values (7.08~7.38) and solubility in 1% NaOH (17.22~17.83%) than other sources. Radial factors significantly affected ethanol-toluene extractive and lignin content. The ethanol-toluene extractive had the highest content (9.30~11.54%) at the outer part of heartwood while lignin content was the lowest (28.12~30.10%) in the inner part. The result indicated some good characteristics of young teak trees compared to the mature ones in relation to wood processing.

Improving Fire Resistance of Mahogany (Swietenia macrophylla) Wood Impregnated with Mixture of Borax and Boric Acid Tomy Listyanto; Aditya Aji Pratama; Keisuke Ando; Nobuaki Hattori
Wood Research Journal Vol 11, No 2 (2020): Wood Research Journal
Publisher : Masyarakat Peneliti Kayu Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.51850/wrj.2020.11.2.48-52

The study was aimed to investigate the effects of mixture of borax and boric acid concentration and different level of pressure on absorption, retention quantity, and fire resistance properties of mahogany (Swietenia macrophylla). A total of 50 samples of 9 x 19 x 1016 mm (ASTM E 69-02) were taken from mahoganylumber and then air-dried. A total of 45 samples were impregnated with aqueous solutions of borax and boric acid in three different concentrations (5, 7, and 9 %) and at three different pressure levels (5, 7.5, and 10 atm) for 2 hours pressure time, while5 samples were liftedas control. Dried impregnated samples and untreated samples were feeding in flame with lid combustion method refers to ASTM E 69-02. Interestingly, the results showed that borax and boric acid effectively improved the fire resistanceproperties(mass losses, ignition temperature, maximum temperature, and smoke and smolder production)of mahogany wood.Mixtures of borax and boric acid at a concentration level of 9% and pressure of 10 atm arerecommended to obtain the best results compare to the other interactions on combustion properties.

Dimensional Stability and Characteristics of Modified Young Teak (Tectona grandis L.f.) Wood with PEG-1000 Tomy Listyanto; Muhammad Navis Rofii; Keisuke Ando; Nobuaki Hattori
Wood Research Journal Vol 6, No 1 (2015): Wood Research Journal
Publisher : Masyarakat Peneliti Kayu Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.51850/wrj.2015.6.1.14-20

The aim of this study was to investigate the effect of wood modification with polyethylene glycol (PEG)-1000 at five concentrations to improve dimensional stability, drying, machining and finishing characteristics of young teak wood. A total of 12 samples for each treatment was prepared to measure an Anti Shrink Efficiency (ASE), as a parameter of dimensional stability and its drying characteristics. Six samples for each treatment were prepared to evaluate machining and finishing characteristics. PEG-1000 with five concentration levels of 20%, 30%, 40%, 50% and 60% were impregnated to modify the samples, except control. Afterward, all samples were kiln dried to gain 12% moisture content. ASE was determined by comparing shrinkage percentage of treated sample with those of untreated one. Warping and surface checks were measured as drying characteristics and machining test was conducted in accordance to ASTM D1666-2004. After coating with a nitrocellulose system, surface quality were evaluated by conducting cross-cut test (ASTM D3359), coin test, delamination test (SNI 01-5008.2-1999b) and glossyness test (SNI-06-6052-1999a). Result shows that dimensional stability of impregnated samples with concentration of 30~60% was successfully improved, with ASE of 52~62%. All treated samples demonstrated good drying characteristics and defect-free areas which were more than 90% under machining test. Surface evaluation by delamination test, glossyness test, and coin test indicated that all impregnated samples were well coated by a nitrocellulose system. However, only impregnated samples in concentration of 20% and 30% showed a good result in cross-cut test. Impregnation with PEG-1000 in concentration of 30% is recommended to modify young teak wood.

Extractive Content and Colour Properties of 11-Year-Old Superior Teak Wood Ganis Lukmandaru; Alfian Nur Falaah; Tomy Listyanto; Dian Rodiana
Wood Research Journal Vol 12, No 1 (2021): Wood Research Journal
Publisher : Masyarakat Peneliti Kayu Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.51850/wrj.2021.12.1.10-17

There is a lack of understanding about the properties of fast-growing teak trees harvested in young stage. Superior teak woods (11 years, 5 trees) grown in Pemalang FMU were assessed in vertical and radial positions for its extractive contents and colour properties. Extractions were conducted using a sequence of toluene, ethanol, and hot water. The color evaluation was performed using CIEL*a*b*’s chromaticity system. Toluene-, ethanol-, hot-water-, and total extractive contents ranged between 1.16~5.00%; 0.29~1,04%, and 0.98~2.35%, and 4.03~7.31%, respectively. For color properties, the brightness (L*), redness (a*), and yellowness (b*) indices ranged from 49.50~57.42, 6.08~10.81, and 20.47~25.74, espectively.Toluene- and total extractive contents were greater in heartwood than in sapwood, while the reverse occurred for the hot-water extractive content. Toluene- and total extractive contents were higher in outer heartwood than in inner heartwood. With regard to colour properties, L* and a* values were significantly differed between sapwood and heartwood. Vertical stem analysis of samples obtained at bottom, center, and top showed the toluene extractive content, total extractive content, and a* levels of center part of the tree were found to be lower than other parts. The L* were negatively correlated with extractive contents, with the highest correlation degree (-0.83**) being observed in the total extractive content in the heartwood. It is also noticed that superior teak wood wood was less darker and extractive contents than the heartwood control of a 72-year-old tree. Therefore, the properties measured in the present work might be related with natural durability of the woods.

Relationship between Wood Properties and Developed Drying Schedule of Inferior Teak (Tectona grandis L.F) and Mahogany (Swietenia macrophylla King) Tomy Listyanto; Ganis Lukmandaru; Candra Pramadya; Dwi Siswanto; Nobuaki Hattori
Wood Research Journal Vol 1, No 2 (2010): Wood Research Journal
Publisher : Masyarakat Peneliti Kayu Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.51850/wrj.2010.1.2.83-88

Development of drying schedule has been a critical issue on a drying process concerning the changing of material condition, especially in Java. Established drying schedule used to be purposed for a high quality timber. The aims of this study were to develop drying schedule of inferior teak and mahogany, and to analyze the relationship between the drying schedule and its wood properties.The specimens were taken from 25 years old teak and 20 years-old mahogany. Wood density, sapwood percentage and extractive contents were determined as wood properties. Four types of specimen’s dimensions (25 x 30 mm; 25 x 50 mm; 25 x 100 mm; and 50 x 50 mm) were dried in the oven with temperature of 103⁰C until reach oven dried conditions. Levels of checks, collapse, and honeycomb were observed to develop drying schedule. A Chi square analysis was used to analyze the relationship between wood properties and the drying schedule.The results showed that there were four types of drying schedule are applicable for teak and five types for mahogany. The most recommended schedule for teak sample was the schedule with an initial temperature (IT) was 70⁰C, relative humidity (RH) was 71%, and the final temperature (FT) was 90⁰C, while the mahogany wood was the schedule with an IT 60⁰C, RH 81%, and the FT 85⁰C, respectively. Chi square analysis indicated that the mahogany lumber dimension was significantly related to the schedule development while specific gravity, heartwood percentage, and extractive content had no significant relationship with the drying schedule development.

Chemical Properties of 15-year-old Teak (Tectona grandis L.f) from Different Seed Sources Ganis Lukmandaru; Pormando Manalu; Tomy Listyanto; Denny Irawati; Rini Pujiarti; Fanny Hidayati; Dian Rodiana
Wood Research Journal Vol 7, No 1 (2016): Wood Research Journal
Publisher : Masyarakat Peneliti Kayu Indonesia

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.51850/wrj.2016.7.1.6-12

Fifteen year-old teak wood samples planted in Ciamis FMU (Perhutani Enterprise) were evaluated for their chemical properties. Three seed sources such as conventional seed, clone, and superior wood and radial positions namely sapwood, outer heartwood, and inner heartwood were the observed factors. The specimens were taken from the bottom parts of their sources. Completely randomized design was used. Cell wall components were analyzed by various gravimetric methods.Analysis of variance and Duncan’s test were performed for data analysis. The results showed that no significant difference in the quantity of cell wall components (cellulose, hemicellulose, and lignin), extractives (ethanol-toluene and hot-water solubles), ash, and silica content among the seed sources. Superior teakwood or Jati Plus Perhutani, which has the highest growth rate (2.1~3.6 cm/year) among others, showed a comparative higher average pH values (7.08~7.38) and solubility in 1% NaOH (17.22~17.83%) than other sources. Radial factors significantly affected ethanol-toluene extractive and lignin content. The ethanol-toluene extractive had the highest content (9.30~11.54%) at the outer part of heartwood while lignin content was the lowest (28.12~30.10%) in the inner part. The result indicated some good characteristics of young teak trees compared to the mature ones in relation to wood processing.

Title

Found 27 Documents
Search

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Title Search

Found 27 Documents Search

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Title

Found 27 Documents
Search