Claim Missing Document
Check
Articles

Found 40 Documents
Search

Analisis Dampak Inter-Band Carrier Aggregation pada Perencanaan Jaringan LTE-Advanced MUBAROK, ARIF; PUTRI, HASANAH
ELKOMIKA: Jurnal Teknik Energi Elektrik, Teknik Telekomunikasi, & Teknik Elektronika Vol 7, No 2 (2019): ELKOMIKA
Publisher : Institut Teknologi Nasional, Bandung

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.26760/elkomika.v7i2.363

Abstract

ABSTRAKPenerapan teknologi Long Term Evolution (LTE) di Indonesia belum optimal dalam pengalokasian spektrum dikarenakan keterbatasan spektrum, untuk mengatasi masalah tersebut 3GPP mengeluarkan teknologi terbaru yaitu LTEAdvanced yang mendukung fitur carrier aggregation (CA) yang memberikan throughput yang lebih tinggi dengan penggunaan spektrum yang lebih efisien. Pada penelitian ini dilakukan perencanaan jaringan LTE-Advanced menggunakan metode inter-band CA dengan menggabungkan dua band frequency yang berbeda yaitu bandwith 5 MHz di band 5 (850 MHz) dan bandwidth 10 MHz di band 3 (1800 MHz). Untuk mendapatkan performansi yang maksimal perencanaan jaringan LTE dan LTE-A dikombinasikan dengan penggunaan skema Physical Cell Identity (PCI) dan Soft Frequency Reuse (SFR). Penggunaan PCI meningkatkan SINR sebesar 1 dB dan throughput meningkat sebesar 200 Kbps, sedangkan penggunaan skema SFR meningkatkan SINR sebesar 9 dB dan throughput meningkat sebesar 13 Mbps.Kata kunci: LTE-Advanced, PCI, SFR, Carrier Aggregation. ABSTRACTThe implementation of Long Term Evolution (LTE) technology in Indonesia has not been optimal due to spectrum limitations. To overcome the problem, 3GPP issued the latest technology, i.e. LTE-Advanced, to support the carrier aggregation (CA) feature that provides higher throughput with more efficient spectrum usage. In this study, LTE-Advanced network planning was performed using the inter-band CA method by combining two different band frequencies, namely 5 MHz bandwidth on Band 5 (850 MHz) and 10 MHz bandwidth on Band 3 (1800 MHz). In addition, to generate maximum performance, the LTE and LTEA networks planning was combined with the use of Physical Cell Identity (PCI) and Soft Frequency Reuse (SFR) schemes. The use of the PCI managed to increase SINR by 1 dB and throughput by 200 Kbps, while the use of SFR scheme managed to increase SINR by 9 dB and throughput by 13 Mbps.Keywords: LTE-Advanced, PCI, SFR, Carrier Aggregation.
Evaluasi Performansi Jaringan UMTS di Kota Semarang menggunakan Metode Drive Test PUTRI, HASANAH
ELKOMIKA: Jurnal Teknik Energi Elektrik, Teknik Telekomunikasi, & Teknik Elektronika Vol 5, No 2 (2017): ELKOMIKA
Publisher : Institut Teknologi Nasional, Bandung

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.26760/elkomika.v5i2.221

Abstract

ABSTRAKSaat ini penggunaan telepon seluler tidak hanya untuk komunikasi suara, melainkan juga untuk komunikasi data. Kota Semarang merupakan salah satu kota besar dengan jumlah pengguna telepon seluler yang banyak. Kondisi ini membutuhkan dukungan kualitas jaringan yang optimal dan kecepatan akses yang tinggi.  Pada penelitian ini dilakukan pengujian kualitas sinyal jaringan UMTS di kota tersebut. Pengukuran dilakukan dengan metode drive test menggunakan software TEMS dan Map info dalam pengolahan datanya. Ada beberapa parameter pengamatan dalam kegiatan pengukuran kualitas jaringan UMTS ini diantaranya RSCP (Receive Signal Code Power), Ec/No, Throughput dan KPI (Key Performance indicator). Setelah dilakukan pengukuran dan analisis perlu dilakukan proses simulasi optimasi yang dilakukan menggunakan software Atoll 3.2.1. Dari hasil pengukuran diperoleh nilai parameter RSCP, Ec/No, dan Throughput berturut-turut sebesar 68,45%, 91%, dan 52.2%. Setelah dilakukan simulasi optimasi terjadi peningkatan nilai parameter RSCP dan Ec/Noberturut-turut sebesar 97.28% dan 99.74%.Kata kunci: UMTS, Drive Test, Map Info, Atoll, KPI.ABSTRACTToday the use of mobile phone is not only for voice communication but also for data communications (mobile Internet). There are a lot of mobile phone users in Semarang, so that it requires the support of a good network quality and high-speed access. In this research, it will test and measure the signal quality UMTS network. The measurement is done with drive test method by using TEMS and Map Info software. There are several parameters of observation in quality measurement of UMTS network. They are RSCP (Received Signal Code Power), Ec/No , Throughput and KPI (Key Performance Indicator). After measurement and analysis it is needed to simulate the optimization recommendations process by using Atoll 3.2.1. to the observation?s parameters. From the measurement results obtained parameter values RSCP, Ec/No , and Throughput, respectively: 68.45, 91% and 52.2%. After the optimization simulation the value are increase significantly to the parameter value of RSCP and Ec/No respectively  97.28% and 99.74%.Keywords: UMTS, Drive Test, Map Info, Atoll, KPI.
METODE CELL SPLITTING PADA PERENCANAAN MICROCELL UNTUK MENINGKATKAN PERFORMANSI JARINGAN LTE ANUGERAH, FIQHI; PUTRI, HASANAH
ELKOMIKA: Jurnal Teknik Energi Elektrik, Teknik Telekomunikasi, & Teknik Elektronika Vol 8, No 2 (2020): ELKOMIKA: Jurnal Teknik Energi Elektrik, Teknik Telekomunikasi, & Teknik Elektro
Publisher : Institut Teknologi Nasional, Bandung

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.26760/elkomika.v8i2.262

Abstract

ABSTRAKBerdasarkan hasil survei dan drive test menggunakan standar operator 3 di wilayah Jalan Kebon Kopi, Kota Cimahi, bahwa nilai parameter LTE yang diperoleh masuk kategori buruk. Hal ini ditunjukkan oleh nilai parameter RSRP <-90 dBm, SINR <5 dB, dan throughput <1 Mbps. Selain itu dari identifikasi Operating Support System (OSS) operator 3 menunjukkan bahwa konsumsi trafik telekomunikasi di wilayah tersebut tinggi. Oleh sebab itu dilakukan perencanaan microcell pada band 3 FDD LTE 1800 MHz menggunakan metode cell splitting. Metode cell splitting ini berperan dalam menghasilkan sel-sel baru dan menyediakan lebih banyak kanal guna memperbaiki performansi serta meningkatkan kapasitas jaringan LTE. Hasil simulasi perencanaan menunjukkan peningkatan nilai rata-rata RSRP sebesar 8,28 dBm, SINR sebesar 3,6 dB, dan throughput sebesar 1.475 Mbps.Kata kunci: kota Cimahi, microcell, cell splitting, LTE, performansi ABSTRACTBased on survey results and drive tests using the operator 3 standard in the Kebon Kopi Street area, Cimahi City, the LTE parameter values obtained are in the bad category. This is indicated by RSRP parameter values <-90 dBm, SINR <5 dB, and throughput <1 Mbps. Besides that, from the identification of the Operating Support System (OSS) the operator 3 shows that consumption of telecommunications traffic in the region is high. Therefore, microcell planning on the 3 band FDD LTE 1800 MHz was carried out using the cell splitting method. This cell splitting method plays a role in generating new cells and providing more channels to improve performance and increase LTE network capacity. Planning simulation results show an increase in the average RSRP value of 8.28 dBm, SINR of 3.6 dB, and throughput of 1.475 Mbps.Keywords: Cimahi city, microcell, cell splitting, LTE, performance
Range expansion method on heterogeneous network to increase picocell coverage Hadi Supriadi; Hasanah Putri
TELKOMNIKA (Telecommunication Computing Electronics and Control) Vol 18, No 5: October 2020
Publisher : Universitas Ahmad Dahlan

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.12928/telkomnika.v18i5.14640

Abstract

In this study, picocell planning was carried out on heterogeneous networks by applying the range expansion method. The case study was conducted in Coblong Subdistrict-Bandung on the 1800 MHz frequency. Heterogeneous network (HetNet) is a system that combines microcell networks and small cell networks (picocell and femtocell). The application of the range expansion method in picocell was aimed to broaden the scope of picocell. For the simulation, Atoll 3.3.0 software with observational parameters was implemented, including RSRP, SINR, throughput, and user connected. The planning results showed that the application of expansion method increased the coverage and quality of network, where the RSRP value ≥ -90 dBm was 97.72%, SINR ≥ 5 dB was 70.99%, uplink throughput was 17.80 Mbps, downlink throughput was 21.37 Mbps, and user connected was 99.2%.
Analysis of Mobility Impacts on LTE Network for Video Streaming Services using Distributed Antenna System Hasanah Putri; Tri Nopiani Damayanti; Rohmat Tulloh
IJAIT (International Journal of Applied Information Technology) Vol 01 No 02 (November 2017)
Publisher : School of Applied Science, Telkom University

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.25124/ijait.v1i02.1044

Abstract

LTE (Long Term Evolution) is a Broadband Wireless Access (BWA) technology that allows high speed and a wide range of access. LTE is designed to meet the needs for Quality of Service (QoS), i.e. the ability to download up to 300 Mbps and upload up to 75 Mbps. This study investigated the impacts of user mobility on the LTE network for video streaming services. The approach employed in this study included multi-user with Distributed AntennaSystem (DAS) and various variations of user mobility speed. Observations were made on the condition of the user moving from one cell to another so that the handover occurred. The throughput value will increase by 33% and 47% when the user’s distances are respectively 1250 m and 2000 m from eNode B. In addition, the delay value will reduce by 66.32% an 67.58% when the user’s distances are respectively 1250 m and 2000 m from eNode B. Moreover, the PDR value will increase by 48.74% and 55.45% when the user’s distances are respectively 1250 m and 2000 m from eNode B. The use of a distributed antenna system (DAS) model on LTE network has resulted in improved quality of performance when the user streams a video.
Improving the eNodeB Coverage of a Bad Spot Area by Using A Relay Node Fivie Ni'mah; Hasanah Putri Putri
IJAIT (International Journal of Applied Information Technology) Vol 02 No 02 (November 2018)
Publisher : School of Applied Science, Telkom University

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.25124/ijait.v2i02.1391

Abstract

The quality of LTE (Long Term Evolution) network in WR Supratman Street, Bandung is categorized as quite bad as shown by the average RSRP (Reference Signal Receive) and SINR (Signal to Interference Noise Ratio) values of -101.30 dBm and 2.43 dB, respectively. Both parameters are below the standard operator with the average RSRP and SINR standard values of -101.30 dBm and 2.43 dB, respectively. The previous field measurement indicated that the area belonged to a bad spot area caused by shadowing buildings. This study used the node scheme of decode and forward and physical mode of inband relay node with the aim of extending the eNodeB coverage. By applying this technique, the average RSRP value increased by 18% and the average SINR value increased by 53%. Based on the RF (Radio Frequency) parameters, the average RSRP value with samples below the -85 dBm standard improved by 81%, while the average SINR value with samples below 5 dB improved by 45%.
PERBANDINGAN UNJUK KERJA TRANSMISI JARINGAN FTTB MENGGUNAKAN GEPON DAN GPON Tri Nopiani Damayanti; Hasanah Putri
Jurnal Elektro dan Telekomunikasi Terapan (e-Journal) Vol 3 No 2: JETT Desember (2016)
Publisher : Direktorat Penelitian dan Pengabdian Masyarakat, Universitas Telkom

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (661.754 KB) | DOI: 10.25124/jett.v3i2.304

Abstract

Penelitian ini dilakukan untuk menganalisa perbandingan unjuk kerja transmisi teknologi GEPON dan GPON pada jaringan Fiber to the Building (FTTB). Pembahasan perbandingan menggunakan  kedua teknologi PON tersebut untuk melihat performansi yang terbaik untuk di aplikasikan pada gedung bertingkat X  menggunakan passive splitter dua tingkat dengan rasio perbandingan passive splitter maksimum 1:16. Unjuk kerja transmisi disimulasikan berdasarkan parameter link power budget, rise time budget serta nilai Bit Error Rate (BER) untuk kelayakan sistem jaringan. Perhitungan Unjuk  jaringan dibagi menjadi bagian yaitu arah downstream dan arah upstream. Hasil perhitungan didapatkan pada arah downstream jarak terjauh, link GEPON menghasilkan nilai redaman sebesar 22.81 dB,  BER sebesar 7x 10-29 dan nilai rise time sebesar 0,2506 ns. Pada link GPON memiliki redaman sebesar 25.94 dB, BER sebesar 3.62955 x 10-12 dan nilai rise time sebesar 0.25 ns. Pada arah upstream jarak terjauh, link GEPON menghasilkan nilai redaman sebesar 4.65 dB, dengan nilai BER ≈ 0 ,dan nilai rise time sebesar,2061 ns. Pada GPON memiliki redaman sebesar 4.65 dB, BER ≈ 0 dan nilai rise time sebesar 0,260 ns. Berdasarkan hasil unjuk kinerja kedua teknologi tersebut dapat disimpulkan bahwa unjuk kinerja teknologi GPON lebih baik dibandingkan teknologi GEPON untuk aplikasikan di jaringan optik gedung bertingkat.
PERENCANAAN INDOOR BUILDING SOLUTION DI WAHANA TRANS STUDIO BANDUNG Hasanah Putri
Jurnal Elektro dan Telekomunikasi Terapan (e-Journal) Vol 7 No 2 (2020): JETT Desember 2020
Publisher : Direktorat Penelitian dan Pengabdian Masyarakat, Universitas Telkom

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.25124/jett.v7i2.3546

Abstract

The Trans Studio Bandung area is a place to vacation with families that are crowded with visitors. However, there are reports that poor access to cellular services for the operator's LTE network 3. Based on the data from the walktest results around the Trans Studio Building area, bad results are obtained, namely the RSRP value of ? -110 dBm and SINR of ? 6 dB. Based on the survey results, this is due to the thick building material so that the signal does not penetrate well into the room. Based on the identification of OSS data, it shows an imbalance between user traffic and cell capacity that affects network quality and throughput. In this study, the optimization of signal quality using the Indoor Building Solution (IBS) method at a frequency of 1800 MHz, 10 MHz bandwidth, and applying lampsite technology to improve service and capacity in the area. This planning simulation was carried out using IBwave 6.6.4 and the ITU-RP1238 propagation model which is Huawei's standard. Observation parameters in this study are RSRP, SINR, and data rates. The results of the planning show an increase in the average RSRP value of -68.83 dBm, and SINR 22.78 dB. Meanwhile, for data rates, it reached a value of 96.8% for values> = 15 Mbps and the lowest value was 34.82 Mbps. This shows that this plan can provide excellent service to users.
PERANCANGAN DAN IMPLEMENTASI SARANA INFORMASI SMAN 3 MADIUN BERBASIS FRAMEWORK CODEIGNITER Aditya Alif Wicaksono; Tengku Ahmad Riza; Hasanah Putri
Jurnal Elektro dan Telekomunikasi Terapan (e-Journal) Vol 3 No 1: JETT Juli (2016)
Publisher : Direktorat Penelitian dan Pengabdian Masyarakat, Universitas Telkom

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (580.707 KB) | DOI: 10.25124/jett.v3i1.132

Abstract

SMAN 3 Madiun merupakan sebuah SMA unggulan di kota Madiun, hal ini tentunya mengakibatkan banyak siswa-siswi yang berkeinginan untuk bersekolah disana untuk setiap tahunnya, namun sangat disayangkan masih banyak terdapat sistem yang dilakukan secara manual disana. Berdasarkan survei yang telah dilakukan kegiatan seperti penilaian siswa dan pendistribusian materi pelajaran masih dilakukan secara manual. Sistem penilaian siswa dan pendistribusian materi pelajaran yang dilakukan secara manual seharusnya bisa dikomputasikan agar mendapatkan hasil yang lebih efisien. Untuk mengatasi masalah tersebut, dalam proyek akhir ini dibuatlah aplikasi berbasis website untuk mengatur sistem penilaian siswa dan pendistribusian materi pelajaran sesuai kurikulum yang berlaku. Yang mana aplikasi ini memiliki beberapa fitur diantaranya, menangani penginputan nilai siswa, monitoring nilai, upload materi, lihat nilai untuk siswa, dan download materi pelajaran.Dari hasil pengujian subjektif, diperoleh score 4.14. Maka performasi aplikasi website untuk penilaian siswa dan pendistribusian materi dinyatakan baik. Dengan demikian dapat dikatan bahwa dengan adanya website tersebut, sistem penilaian siswa dan pendistribusian materi pelajaran menjadi lebih mudah dan efisien.
PERANCANGAN DAN IMPLEMENTASI TUNER GITAR OTOMATIS DENGAN PENGGERAK MOTOR SERVO BERBASIS ARDUINO Randi Yusuf Nasution; Hasanah Putri; Yuli Sun Hariyani
Jurnal Elektro dan Telekomunikasi Terapan (e-Journal) Vol 2 No 1: JETT Juli (2015)
Publisher : Direktorat Penelitian dan Pengabdian Masyarakat, Universitas Telkom

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (767.691 KB) | DOI: 10.25124/jett.v2i1.96

Abstract

Gitar merupakan salah satu alat musik yang paling digemari, dan dapat dimainkan oleh semua orang. Saat ini masih banyak ditemukan pengguna gitar yang tidak bisa melakukan tuning senar gitar dan jika dilakukan manual juga membutuhkan waktu yang lama untuk mendapatkan hasil tuning yang akurat. Hal ini dapat diatasi dengan perkembangan teknologi Pengguna gitar sekarang ini dapat melakukan tuning senar lebih mudah dan lebih cepat dengan tingkat toleransi kesalahan frekuensi tuning ± 1 Hz dengan menggunakan tuner gitar otomatis.Perancangan alat tuner gitar otomatis ini menggunakan 5 komponen pembentuk alat yaitu selector switch untuk memilih frekuensi yang akan diatur, Op amp untuk menguatkan amplitudo gelombang suara agar diterima arduino dengan baik, Arduino untuk menginisialisasi frekuensi dan memberi sinyal ke motor servo, Motor servo untuk melakukan tuning senar gitar, dan LED sebagai indikator tuning.Hasil dari penelitian ini adalah keakuratan tuning untuk setiap senar didapatkan rata-rata tuning paling baik yaitu senar 5 dengan rata-rata kesalahan tuning 0,07 Hz dan rata-rata tuning paling buruk yaitu senar 1 dengan rata-rata kesalahan tuning sebesar 0,8 Hz. Alat yang dapat membantu pengguna gitar melakukan tuning senar gitar secara otomatis dengan tingkat kesalahan maksimum ± 1 Hz dari standar frekuensi setiap nada senar gitar yang telah ditetapkan.