Claim Missing Document
Check
Articles

Found 5 Documents
Search
Journal : Medika Trada

RANCANG BANGUN ALAT WATER BATH DILENGKAPI INDIKATOR LEVEL AIR BERBASIS ARDUINO MEGA2560 Nuha ABA, Muhammad Ulin; Muslihun; Yulianto Lamahala Tukan, Wilhelmus
MEDIKA TRADA : Jurnal Teknik Elektomedik Polbitrada Vol 3 No 2 (2022): MEDIKA TRADA (JTEMP) Vol 3 No 2 (2022)
Publisher : LPPM POLBITRADA

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.59485/jtemp.v3i1.21

Abstract

Laboratorium merupakan tempat yang dilengkapi dengan berbagai instrumen, peralatan dan bahan kimia (reagen), kegiatan yang dilakukan pada laboratorium meliputi karya eksperimental, kegiatan penelitian dan prosedur pemeriksaan. Water bath merupakan suatu alat yang digunakan pada laboratorium kesehatan untuk melaksanakan kegiatan serologi, aglutinasi, inaktivasi, biomedis, terfarmasi dan prosedur inkubasi industri. Fungsi utama Water bath adalah membuat suhu yang konstan dengan waktu yang sudah ditentukan. Maka, penelitian ini akan merancang alat water bath dilengkapi dengan sensor ketinggian air dengan menggunakan komponen pendukung berupa Arduino Mega 2560, sensor DS18B20, keypad 4x4, driver relay, heater, driver water level dan LCD 20x4. Metode penelitian yang digunakan dalam pengujian ini dengan menguji suhu pada wadah dengan mengukur suhu pada wadah alat. Jika kinerja alat sudah sesuai atau suhu yang diuji dengan menggunakan sensor DS18B20 tidak berbeda jauh dengan alat pembanding, maka alat sudah bekerja dengan baik dan jika hasil yang ditampilkan kurang baik, artinya suhu pada wadah tidak tersebar dengan merata sehingga suhu pada wadah tidak sesuai dengan pengaturan suhu. Kesimpulan dari penelitian ini yaitu Wadah memiliki pemansan yang maksimal disuhu 37°C - 50°C. Nilai Error terendah pada pengujian pembacaan sensor suhu adalah 0,20% pada suhu 50°C dan terbesar 1,11% pada pengujian suhu 45°C. Nilai Error terendah pada pengujian alat adalah 1,77% pada suhu 44°C dan terbesar yaitu 3,66% pada pengujian suhu 47°C.
ALAT MONITORING KONSENTRASI OKSIGEN DAN ALIRAN UDARA PADA REGULATOR OKSIGEN Haris Kuspranoto, Abdul; Muslihun; Walikram, Zulzala
MEDIKA TRADA : Jurnal Teknik Elektomedik Polbitrada Vol 3 No 2 (2022): MEDIKA TRADA (JTEMP) Vol 3 No 2 (2022)
Publisher : LPPM POLBITRADA

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.59485/jtemp.v3i1.22

Abstract

Oksigen merupakan suatu kebutuhan hidup yang sangat jarang dipikirkan meskipun memiliki nilai yang sangat tinggi bagi manusia. Untuk pasien dengan penyakit paru obstruktif kronis atau pasien dengan atelektasis oleh oksigenasi, risiko asidosis respiratori meningkat ketika oksigen diberikan sebebasnya tanpa terukur. Untuk menghindari asidosis ini, saturasi oksigen harus dijaga antara 88% dan 92% dan laju aliran oksigen. Karena itu keakuratan sistem pengiriman aliran oksigen penting. Alat ini mendeteksi kadar oksigen dan tekanan udara pada gas oksigen menggunakan sensor OCS-3F. Untuk memastikan tekanan udara / flow dan kadar oksigen yang akan diberikan ke pasien, maka munculah ide dari peneliti untuk melakukan penelitian ini. Dengan melakukan 5 titik pengujian di 2, 3, 5, 6, dan 7 Liter per menit serta masing masing titik pengujian dilakukan 5 kali pengukuran, dan juga melakukan pengambilan 3 titik pengukuran untuk nilai yang diambil di cocokan dengan regulator. Maka dari itu, dapat disimpulkan bahwa alat monitoring konsentrasi oksigen dan laju udara pada regulator oksigen berhasil dibuat dan bekerja dengan baik, dimana pembacaan sensor yang baik dan hasil pengukuran akurasi laju tekanan udara dengan kesalahan lebih kurang 1%.
RANCANG BANGUN ALAT BLANKET WARMER BERBASIS ARDUINO Andrianto, Dian; Muslihun; Wawan Setiawan, Lalu
MEDIKA TRADA : Jurnal Teknik Elektomedik Polbitrada Vol 3 No 2 (2022): MEDIKA TRADA (JTEMP) Vol 3 No 2 (2022)
Publisher : LPPM POLBITRADA

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.59485/jtemp.v3i1.23

Abstract

Advances in technology have made health services more developed, especially in anesthesia. Anesthesia is an attempt to relieve pain. The post-anesthesia recovery period is needed as a time with a high risk for complications. It was found that 2.5% of patients experienced complications after undergoing anesthesia. One of the complications that will arise after anesthesia is hypothermia. The negative effects of hypothermia on patients include increased bleeding risk, myocardial ischemia, longer post-anesthesia recovery, impaired wound healing, and the risk of infection. Blanket warmer is a device that is used for the patient's body when experiencing hypothermia. This tool basically utilizes the heat energy generated by the heater and uses a blower as a heat conducting medium, and a DS18B20 sensor to unite the patient's body temperature and the thermistor temperature sensor as a detector of hot air produced by the heater and blower. The results of measuring the comparison of patient temperature between the research tool and a digital thermometer get the largest percentage of 0.1% where the largest error percentage is in samples 1 and 2. 3.
DESAIN UNTUK HOT PLATE MAGNETIK STIRRER DENGAN MOTOR RPM TINGGI Ulin Nuha ABA, Muhammad; Kuspranoto, Abdul Haris; Muslihun; Saktira P.S, Riza; Tri Harsoyo, Imam
MEDIKA TRADA : Jurnal Teknik Elektomedik Polbitrada Vol 5 No 2 (2024): MEDIKA TRADA (JTEMP) Vol 5 No 2 (2024)
Publisher : LPPM POLBITRADA

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.59485/jtemp.v5i2.92

Abstract

Hotplate magnetic stirrer is laboratory equipment used to mix solutions to make them more homogeneous by utilizing a heater and magnetic rod controlled by a high RPM motor, as well as several other supporting components. All these components are assembled into one good tool. In order to produce a good magnetic stirrer hotplate tool, it is necessary to make a planning design to produce a magnetic stirrer hotplate tool that is ergonomic and functional. In designing this tool, several stages of literature study are carried out, designing the tool (to find out the various components needed), designing the tool using a computer, printing the tool, installing components and testing the electrical power of the tool. Based on these steps, the casing design for the Hotplate Magnetic Stirrer tool was successfully created with a length = 230 mm, width = 220 mm, and height = 156 mm. This casing design is able to accommodate all electronic and non-electronic components used, especially high RPM DC motors. It is proven that through this casing design, the high RPM DC motor and other components are installed (attached) well. It has also been confirmed that all installed electronic components have voltage according to their specifications. Keywords: Magnetic Stirrer Hotplate, Design, Motor, RPM, Components.
Analisis Manajemen Sistem Pemeliharaan Alat Kesehatan Mugiyanto; Muslihun; Ekma Nurani, Annisa
MEDIKA TRADA : Jurnal Teknik Elektomedik Polbitrada Vol 6 No 1 (2025): MEDIKA TRADA (JTEMP) Vol 6 No 1 (2025)
Publisher : LPPM POLBITRADA

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.59485/jtemp.v6i1.119

Abstract

Abstrak Maintenance of medical equipment is very necessary and is even a priority in important programs in a health service. As per the Regulation of the Minister of Health (Permenkes) Number 15 of 2023. concerning the maintenance of medical devices in health service facilities. More specifically, as mandated by Law Number 44 of 2009 concerning Hospitals, medical equipment must be tested and calibrated. The purpose of this study is to determine the correct method and procedure for maintaining medical devices. While the purpose of maintaining the device is to maintain the level of accuracy of the device and to be able to operate properly. This study uses the Literature Review Article method using 15 journals as data sources which are electronic data. The results of this study contain several aspects in the maintenance of health equipment. In addition, from various literatures, it can be concluded that there is a significant relationship between tool maintenance and the quality assurance of the period of use of the device and also the quality of the examination results using the device. As a suggestion for implementing tool maintenance, testing and calibration of health devices should not only be to fulfill existing regulations or regulations. However, the most important thing is how to guarantee the quality of medical services and patient safety.