cover
Contact Name
Muhammad Nizar
Contact Email
muhammad.nizar@serambimekkah.ac.id
Phone
-
Journal Mail Official
serambiengineering@serambimekkah.ac.id
Editorial Address
-
Location
Kota banda aceh,
Aceh
INDONESIA
Jurnal Serambi Engineering
ISSN : 25283561     EISSN : 25411934     DOI : https://doi.org/10.32672/jse
Jurnal Serambi Engineering diterbitkan oleh Fakultas Teknik Universitas Serambi Mekkah Banda Aceh. Jurnal ini diterbitkan sebagai media untuk menyalurkan informasi hasil penelitian dibidang keteknikan baik yang dilakukan oleh para dosen dari Fakultas Teknik, khususnya dari Universitas Serambi Mekkah maupun dari pihak lain. Penelitian yang dipublikasikan dapat berupa penelitian lapangan maupun laboratorium serta kajian literatur.
Arjuna Subject : -
Articles 1,178 Documents
Evaluasi Perbandingan Gas Buang Hasil Pengolahan Sampah Domestik Menggunakan Teknologi Termal Rizki Kurnia Putra; Novirina Hendrasarie
Jurnal Serambi Engineering Vol 8, No 3 (2023): Juli 2023
Publisher : Fakultas Teknik

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.32672/jse.v8i3.6149

Abstract

Kuantitas limbah padat domestik berbanding lurus dengan kenaikan jumlah penduduk. Pengumpulan dan pembuangan limbah memerlukan sistem pengelolaan limbah padat yang bersih dan efektif. Sistem pengelolaan limbah padat yang efisien biasanya akan tumbuh sebanding dengan ukuran pemukiman dan pendapatan per kapita penduduk. Teknologi pembakaran limbah kota memegang peranan penting dalam mengolah dan juga memampatkan produksi limbah pemukiman/perkotaan. Hal tersebut dikarenakan selain berperan dalam proses penyusutan volume limbah padat, teknologi pembakaran yang sesuai adalah insinerasi dan gasifikasi. Penelitian ini bertujuan untuk melakukan evaluasi  perbandingan gas buang hasil pengolahan sampah domestik menggunakan teknologi termal insinerasi dan gasifikasi. Metode penelitian yang dilakukan adalah dengan melakukan uji emisi pada insinerasi dan gasifikasi dengan variasi sampah biodegradable, non-biodegradable, dan campuran. Hasil yang didapatkan adalah Kadar CO terendah adalah variabel biodegradable 100 Kg pada insenerasi dengan nilai 31,86 mg/Nm3. NOx terendah adalah variabel biodegradable 100 Kg pada Insinerasi dengan nilai 63,22 mg/Nm3. HCl terendah adalah variabel biodegradable 100 Kg pada Insinerasi dengan nilai 12,53 mg/Nm3. SO2 terendah adalah variabel biodegradable 100 Kg pada Insenerasi dengan nilai 40,63 mg/Nm3.
Model Persamaan Kumulatif Muatan dan Tinggi Draft Tongkang Terhadap Kumulatif Cycle Time Batu Bara di Pelabuhan Karya Citra Nusantara Marunda Geby Thesya Paskarina; Hartati M Pakpahan
Jurnal Serambi Engineering Vol 8, No 1 (2023): Januari 2023
Publisher : Fakultas Teknik

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.32672/jse.v8i1.5582

Abstract

AbstractKarya Citra Nusantara Marunda Port is one of the ports that is a port business entity in Indonesia; this port can carry out bulk products unloading activities, including coal, sand, and others. The quantity of cargo in the barge increases as the draft of the barge falls, and vice versa; when the draft of the barge begins to rise, the amount of cargo drops gradually and the excavator's unloading time increases. Considering this, research must be done to ascertain the mathematical model relating to the duration of coal unloading at Marunda Port and to establish the cumulative impact of cargo volume and barge draft height. A multiple linear regression equation model was created for the time of coal unloading using the enter method, Y = -152.076 + 16.157X1 - 148.304X2, based on the findings of the analysis of traditional assumptions and hypotheses that was conducted as a prerequisite for creating a good equation model. The unloading cycle time will be 152,076 minutes shorter with the unloading time per barge when the amount of cargo per tonne drops. The needed unloading cycle time will be increased if the cargo volume rises by 16,157 tons.Keywords: port, unloading time, cycle time, total load, draft height, multiple linear regression
Analisis Pengukuran Kerja Menentukan Waktu Baku Menggunakan Metode Jam Henti Terhadap Operator Persiapan Komponen (Studi Kasus: PT XYZ) Sigma Asarela; Rianita Puspa Sari
Jurnal Serambi Engineering Vol 8, No 3 (2023): Juli 2023
Publisher : Fakultas Teknik

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.32672/jse.v8i3.6315

Abstract

Perusahaan besar memiliki tanggung jawab dalam memenuhi kebutuhan konsumen secara cepat dan tepat, maka dari itu perusahaan perlu melakukan pengoptimalan pada setiap proses operasi. Pada PT XYZ belum pernah dilakukan pengukuran waktu baku untuk operator pick preparation di gudang. Karena situasi ini, Penelitian ini dilakukan dengan tujuan untuk mengukur waktu baku dengan menggunakan metode jam henti. Penelitian ini bertujuan mengukur waktu baku dalam suatu proses pekerjaan agar perusahaan bisa memiliki acuan dalam menetapkan jam kerja dan jumlah tenaga kerja yang dibutuhkan serta target jumlah produksi.  Metode jam henti digunakan dalam penelitian karena pada penelitian ini dilakukan pengamatan langsung terhadap suatu pekerja atau proses secara berulang-ulang hingga data terpenuhi dengan menggunakan instrumen lembar pengamatan dan stopwatch. Penelitian dilaksanakan di gudang PT XYZ dengan objek penelitian adalah operator pick and preparation komponen front fork HKZR. Penelitian dilakukan dengan membagi elemen kerja menjadi 7 bagian sebanyak 10 kali pengamatan. Hasil dari penelitian didapatkan bahwa waktu baku untuk elemen kerja 1, 2, 3, 4, 5, 6, dan 7 secara berurutan sebesar 17,54 detik, 207,60 detik, 110,46 detik, 1617,74 detik, 126,22 detik, 104,77 detik, dan 19,01 detik.
Kendala Teknologi, Pendanaan dan Ketersediaan Bahan Baku Biomassa dalam Pengembangan Energi Terbarukan Arsyad Arsyad; Syaifuddin Yana; Radhiana Radhiana; Ulfia Ulfia; Fitriliana Fitriliana; Juwita Juwita
Jurnal Serambi Engineering Vol 8, No 1 (2023): Januari 2023
Publisher : Fakultas Teknik

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.32672/jse.v8i1.5666

Abstract

AbstractThe world’s energy needs keep rising but numerous difficulties remain to meet energy needs. Technological, financing, and biomass raw material issues hinder biomass energy expansion. Renewable energy development faces this main challenge. Converting biomass into energy is still expensive. High�tech investments cost more. Modern technology demands lots of raw materials. Industrial biodiesel capacity is 12.5 million kilolitres. 3 million kilolitres, or 25%, are used. Funding issues also exist. Bioenergy processors require incentives to invest. Improve regulations to sustain investment. The financial services authority should sponsor and finance green projects like renewable energy development to help this industry grow and survive. However, feedstock availability and sustainability remain the biggest challenge. Feedstock supply and biomass price stability remain challenges. Therefore, stakeholders and the government and businesses that use their resources must cooperate and coordinate. Planning, regulation, and coordination are the keys to preserving the biomass resource activity cycle. The government should strengthen regulations through linked ministries to ensure its sustainability.Keywords: biomass energy conversion, technological limitations, finance limits, biomass raw material availability, legislation for biomass energy
Estimating Zero Waste Index and Resident Waste Participation in Indonesian Middle City Muhammad Nizar; Rahadian Zainul; Syaifuddin Yana; Erdiwansyah Erdiwansyah; Irda Yunita
Jurnal Serambi Engineering Vol 7, No 2 (2022): April 2022
Publisher : Fakultas Teknik

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.32672/jse.v7i2.5905

Abstract

The municipal city has tried to provide the best solid waste services as possible, but the increase in these services does not necessarily increase public participation in managing waste. The objective of this research is to measure the performance of municipal solid waste management while Banda Aceh Indonesia. The research method uses the Zero Waste Index tool and community surveyed to get a more comprehensive picture of performance in overcoming waste problems. The results can be concluded that the Banda Aceh city government is still achieving a small Zero Waste Index which is 0.28. The majority of the population does not get waste socialization (76.07%), does not sort (75.21%), does not recycle waste (68.31%) and only 54.70% of the community collect used items for resale. The results of the two studies show that it is hard for Banda Aceh to achieve the goal of 30% waste reduction by 2025.
Prediksi Kecepatan Angin Jangka Menengah dengan Artificial Neural Network untuk Estimasi Daya Listrik Tenaga Angin (Studi Kasus: Kota Sabang) Abdul Malek; Suriadi Suriadi; Khairun Saddami
Jurnal Serambi Engineering Vol 8, No 3 (2023): Juli 2023
Publisher : Fakultas Teknik

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.32672/jse.v8i3.6010

Abstract

Indonesia, as a country at the equator, has a very large renewable energy potential that can be used as a source of electrical energy. Electricity consumption in Indonesia, especially in Aceh, continues to increase annually because of population growth and increasing economic needs. Recently, the construction of power plants has been considered to be environmentally friendly and economical. One of the efforts that can be made is the development of wind-power plants. The availability of certain wind speeds was expected. Therefore, accurate prediction data must be used as the basis for building wind power plants. To increase the accuracy of wind speed prediction by looking at the error rate in predicting the amount of wind speed generated using an Artificial Neural Network with feed-forward and feed-backward functions from the back propagation algorithm (BPNN). The results of the application using the Neural Network algorithm with a back propagation Neural Network (BPNN) to predict wind speed show that the Neural Network algorithm can predict wind speed with an error of 0.0036. In July 2021, the estimated energy demand is 81.5 KWH.
Prediksi Jumlah Penumpang Bus Trans Metro Dewata Pada PT. Satria Trans Jaya Menggunakan Double Exponential Smoothing dan Weighted Moving Average N Dinda Maharani; I Gede Aris Gunadi; Komang Setemen
Jurnal Serambi Engineering Vol 8, No 2 (2023): April 2023
Publisher : Fakultas Teknik

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.32672/jse.v8i2.5686

Abstract

Peramalan merupakan teknik atau proses untuk melakukan prediksi suatu kejadian di masa depan dengan menggunakan data histori sebelumnya. Transportasi umum merupakan layanan jasa untuk mengangkut orang atau barang dari satu tempat ke tujuan tempat lainnya. Tujuan penelitian ini untuk memprediksi jumlah penumpang transportasi umum yaitu bus Trans Metro Dewata pada setiap koridor di masa mendatang dengan metode peramalan yang tepat. Metode peramalan yang di gunakan adalah Double Exponential Smoothing dan Weighted Moving Average. Pada penelitian ini menggunakan Mean Absolut Precentage Error (MAPE) sebagai nilai uji akurasi error. Hasil peramalan berdasarkan nilai MAPE bahwa Double Exponential Smoothing lebih tepat digunakan dibandingkan Weighted Moving Average karena nilai error yang di hasilkan lebih kecil, yaitu koridor I sebesar 7,41%, koridor II sebesar 7,05%, koridor III sebesar 9,83%, koridor IV sebesar 6,37% dan hasil peramalan 48 periode mendatang menghasilkan tren meningkat lurus.
Penilaian Risiko Postur Kerja Berdasarkan Metode RULA Pada Pekerja Manual Handling di Toko H. Dadang Mochamad Rafi Herdiana; Asep Erik Nugraha
Jurnal Serambi Engineering Vol 8, No 1 (2023): Januari 2023
Publisher : Fakultas Teknik

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.32672/jse.v8i1.5064

Abstract

Manual material handling is a very important study in the industrial world. Conceptually, material handling in workers by utilizing labor. Flexibility of movement and wide accessibility are among the reasons the industry still utilizes manual material refining. On the other hand, the risk caused by the work is spinal injury (low back pain). Many use methods to analyze working postural on MMH. The study used the RULA method and a nordic body map questionnaire. The use of NBM questionnaires to find out complaints ergonomically, while the RULA Method is to analyze ergonomic risks in the upper part of the body. Toko H. Dadang is a grocery store that sells various basic necessities and others, with operators totaling 4 people. In the results of this study 4 people had upper ergonomic injuries. with the help of NBM questionnaires and analyzing the relationship of ergonomic risk with the RULA method. In the RULA method assesses the work of operators, on operators 1 it is worth 7. Thus, recommendations are given by using a freight trolley to prevent further ergonomic risks. 
Analisis Produktivitas Tenaga Kerja Terhadap Hasil Produksi di Cv. Mulia Tata Sejahtera Ikhsan Galih Prayoga; Agustian Suseno
Jurnal Serambi Engineering Vol 8, No 2 (2023): April 2023
Publisher : Fakultas Teknik

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.32672/jse.v8i2.5775

Abstract

Produktivitas sangat penting bagi bisnis di masa persaingan yang ketat, sehingga setiap bisnis perlu meningkatkan efisiensi operasionalnya agar dapat bersaing dengan bisnis lainnya. Berbagai faktor bisa mempengaruhi kemajuan atau kemunduran suatu perusahaan, salah satunya adalah produktivitas. Untuk memperbaiki produktivitas di masa mendatang dapat dilakukan dengan melakukan pengukuran produktivitas, pengukuran ini dapat dilakukan dengan memperhatikan perhitungan jumlah output yang dihasilkan oleh suatu perusahaan dipengaruhi oleh jumlah sumber daya. Maksud dari penelitian ini ialah untuk mencari tahu tingkat produktivitas tenaga kerja unit produksi pada CV. Mulia Tata Sejahtera serta agar dapat mengetahui factor apa saja yang berdampak terhadap produktivitas tenaga kerja. Penelitian dikerjakan dengan metode wawancara secara mendalam dengan karyawan yang ada dan mengamati proses produksi yang dilakukan oleh CV. Mulia Tata Sejahtera. Berdasarkan hasil perhitungan total produktivitas yaitu dengan membagi output atau hasil produksi dari CV. Mulia Tata Sejahtera dengan input atau jumlah karyawan CV. Mulia Tata Sejahtera. Sehingga didapatkan hasil untuk produktivitas tenaga kerja di CV. Mulia Tata Sejahtera pada tahun 2021 yaitu sebesar 2,27%. Nilai Produktivitas parsial tenaga kerja total selama setahun adalah 2,27% dengan nilai rata rata 0,19%. Nilai produktivitas rata-rata setiap bulannya ini masih terbilang rendah jadi masih perlu ditingkatkan lagi.
Pemodelan Dampak Perubahan Iklim dan WIUP terhadap Potensi Habitat Burung Walik Benjol di Pulau Obi Kartika Pratiwi; Supriatna Supriatna; Masita Dwi Mandini Manessa; Aris Poniman K; Mangapul P. Tambunan
Jurnal Serambi Engineering Vol 8, No 1 (2023): Januari 2023
Publisher : Fakultas Teknik

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.32672/jse.v8i1.5571

Abstract

AbstractOne of the impacts of climate change is the degradation quality of natural habitats of flora and fauna in Indonesia, risking the loss of most of the existing biodiversity. Obi Island as a natural habitat for several endemic species cannot be avoided from the threat of climate change impacts. The existence of mining concessions also can have a direct impact on their habitat potential. The purpose of this study was to analyze the distribution pattern of endemic species under current climatic conditions, synthesize models of the impact of climate change and analyze mining concessions on the distribution of potential habitats of Carunculated Fruit-dove on Obi Island. The occurrence data of Carunculated Fruit-dove and 19 bioclimatic variables are used as input in the process of making a habitat model with MaxEnt. As a result, the habitat potential model of Carunculated Fruit-dove with AUC = 0.955 has a very suitable habitat potential with an area of 66.02 km2 or 2.68%. The climate change in 2041-2060 with 4 different climate scenarios has an impact on the Carunculated Fruit-dove habitat potential model. Mining Business Permit Areas on Obi Island that have been issued until March 2022 amount to 19 locations with a total area of 373.14 km2 which will have a direct or indirect impact on the potential habitat of Carunculated Fruit-dove on Obi Island. 14.17 km2 of 66.67 km2 of potential habitat that is very suitable for Carunculated Fruit-dove will be directly affected by the existence of these mining areas.Keywords: endemic species, mining business permit area, climate change, obi island, maximum entropy