Jurnal Rekayasa elektrika
The journal publishes original papers in the field of electrical, computer and informatics engineering which covers, but not limited to, the following scope: Electronics: Electronic Materials, Microelectronic System, Design and Implementation of Application Specific Integrated Circuits (ASIC), VLSI Design, System-on-a-Chip (SoC) and Electronic Instrumentation Using CAD Tools, digital signal & data Processing, , Biomedical Transducers and instrumentation, Medical Imaging Equipment and Techniques, Biomedical Imaging and Image Processing, Biomechanics and Rehabilitation Engineering, Biomaterials and Drug Delivery Systems; Electrical: Electrical Engineering Materials, Electric Power Generation, Transmission and Distribution, Power Electronics, Power Quality, Power Economic, FACTS, Renewable Energy, Electric Traction, Electromagnetic Compatibility, High Voltage Insulation Technologies, High Voltage Apparatuses, Lightning Detection and Protection, Power System Analysis, SCADA, Electrical Measurements; Telecommunication: Modulation and Signal Processing for Telecommunication, Information Theory and Coding, Antenna and Wave Propagation, Wireless and Mobile Communications, Radio Communication, Communication Electronics and Microwave, Radar Imaging, Distributed Platform, Communication Network and Systems, Telematics Services and Security Network; Control: Optimal, Robust and Adaptive Controls, Non Linear and Stochastic Controls, Modeling and Identification, Robotics, Image Based Control, Hybrid and Switching Control, Process Optimization and Scheduling, Control and Intelligent Systems, Artificial Intelligent and Expert System, Fuzzy Logic and Neural Network, Complex Adaptive Systems; Computer and Informatics: Computer Architecture, Parallel and Distributed Computer, Pervasive Computing, Computer Network, Embedded System, Human—Computer Interaction, Virtual/Augmented Reality, Computer Security, Software Engineering (Software: Lifecycle, Management, Engineering Process, Engineering Tools and Methods), Programming (Programming Methodology and Paradigm), Data Engineering (Data and Knowledge level Modeling, Information Management (DB) practices, Knowledge Based Management System, Knowledge Discovery in Data), Network Traffic Modeling, Performance Modeling, Dependable Computing, High Performance Computing, Computer Security, Human-Machine Interface, Stochastic Systems, Information Theory, Intelligent Systems, IT Governance, Networking Technology, Optical Communication Technology, Next Generation Media, Robotic Instrumentation, Information Search Engine, Multimedia Security, Computer Vision, Information Retrieval, Intelligent System, Distributed Computing System, Mobile Processing, Next Network Generation, Computer Network Security, Natural Language Processing, Business Process, Cognitive Systems. Signal and System: Detection, estimation and prediction for signals and systems, Pattern recognition and classification, Artificial intelligence and data analytics, Machine learning, Deep learning, Audio and speech signal processing, Image, video, and multimedia signal processing, Sensor signal processing, Biomedical signal processing and systems, Bio-inspired systems, Coding and compression, Cryptography, and information hiding
Articles
600 Documents
<![CDATA[Auskultasi Jarak Jauh untuk Pengukuran dan Perekaman Sinyal Suara Jantung ]]>
<![CDATA[Eka Sari Oktarina]]>;
<![CDATA[Ira Puspasari]]>;
<![CDATA[Jusak Jusak]]>
<![CDATA[ Jurnal Rekayasa Elektrika Vol 14, No 3 (2018) ]]>
Publisher : <![CDATA[Universitas Syiah Kuala ]]>
Show Abstract
|
Download Original
|
Original Source
|
Check in Google Scholar
|
Full PDF (963.518 KB)
|
DOI: 10.17529/jre.v14i3.12013
<![CDATA[In 2014, the Sample Registration System (SRS) released a survey showing that heart diseases can be categorized as the second highest non-communicable disease in Indonesia. The percentage is 12.9%. In this work, a tele-auscultation system for heart sound signals was built to transmit the signal over the global Internet networks and store them in a Cloud storage. Thus, the system allows measurement of heart sound signal for the rural area where the presence of expert is very scarce and helps the expert doctors to perform clinical analysis anywhere. Our examination showed that the system exhibited the average transmission delay of 5.68 second and data lost of only less than 1% for transmission of 1 heart sound signal. On the other hand, examination using two heart sound signals transmitted simultaneously showed that it displayed a smaller average of transmission delay. It may be caused by the measurement of the transmission delay as well as data lost that is depended on the traffic in the internet networks. Moreover, correlation of the heart sound signals before and after transmission showed a strong correlation where the correlation value is very close to 1 at, indicating that there is a strong similarity between the two signals.]]>
<![CDATA[Pengukuran RSSI Jaringan Sensor Nirkabel Berbasis ZigBee pada Berbagai Topologi ]]>
<![CDATA[Helmy Fitriawan]]>;
<![CDATA[Roviq Cholifatul Rohman]]>;
<![CDATA[Herlinawati Herlinawati]]>;
<![CDATA[Sri Purwiyanti]]>
<![CDATA[ Jurnal Rekayasa Elektrika Vol 16, No 2 (2020) ]]>
Publisher : <![CDATA[Universitas Syiah Kuala ]]>
Show Abstract
|
Download Original
|
Original Source
|
Check in Google Scholar
|
Full PDF (1055.071 KB)
|
DOI: 10.17529/jre.v16i2.15750
<![CDATA[In order to get a good performance from a wireless sensor network, it is necessary to measure parameters of the network. RSSI (Received Signal Strength Indicator) is one of the network parameters that measure the signal strength received by a radio receiver in communication module. In this study the RSSI measurement experiment was performed in a wireless sensor network with the ZigBee protocol. Measurements were accomplished in three topologies, i.e. point-to-point, star, and mesh, both indoor and outdoor scenarios. Indoor measurements are carried out within the laboratory with concrete wall partition, while outdoor measurements are carried out in open space with the line-of-sight (LOS) conditions. XCTU software is used to measure RSSI measurements, by sending 100 data packets of 64 bytes with 1 second delivery intervals. Results show that the farther the data transmission distance, the RSSI value relatively decrease due to obstacles and reduced radio signal strength. While, in the mesh topology the addition of a router will also cause a slightly increase in the RSSI value. ]]>
<![CDATA[Pengembangan Pintu Air Irigasi Pintar berbasis Arduino untuk Daerah Irigasi Manikin ]]>
<![CDATA[Folkes Eduward Laumal]]>;
<![CDATA[Edwin P. Hattu]]>;
<![CDATA[Kusa B. N. Nope]]>
<![CDATA[ Jurnal Rekayasa Elektrika Vol 13, No 3 (2017) ]]>
Publisher : <![CDATA[Universitas Syiah Kuala ]]>
Show Abstract
|
Download Original
|
Original Source
|
Check in Google Scholar
|
Full PDF (681.654 KB)
|
DOI: 10.17529/jre.v13i3.8505
<![CDATA[In general, irrigation watergates placed in the Manikin Irrigation Area is supporting tools for agricultural activities that implement a primary–secondary–tertiary channel system. Manikin irrigation watergate is made of iron plates with the certain size which is operated by a move up/down or rotation. This mechanism has led the dissatisfaction service problems in farmers. This study has developed smart irrigation watergate based on Arduino by replacing the lifter/rotator part using DC motor that works automatically based on the Real-time Clock sensor. This sensor sends the data time to Arduino and used as the reference to open or close the watergate. The study used a design method includes interconnecting realtime clock sensors and Arduino, build the programming control, build the DC system on watergates and interconnection to control systems and testing. The test results show that the irrigation watergate moves up and move down every 2 hours based on the data time from the real-time clock, works with a 12-hour time format and operating on 2.7-ampere current.]]>
<![CDATA[Pemantauan Pembangkit Listrik Tenaga Mikrohidro (PLTMH) ]]>
<![CDATA[Arif Gunawan]]>;
<![CDATA[Arisco Oktafeni]]>;
<![CDATA[Wahyu Khabzli]]>
<![CDATA[ Jurnal Rekayasa Elektrika Vol 10, No 4 (2013) ]]>
Publisher : <![CDATA[Universitas Syiah Kuala ]]>
Show Abstract
|
Download Original
|
Original Source
|
Check in Google Scholar
|
Full PDF (394.353 KB)
|
DOI: 10.17529/jre.v10i4.1113
<![CDATA[This research is motivated by electrical power shutting-down that frequently occurred in Riau province. Low electrical power supply as compared to the need causes lack of supply. Thus, new alternative electrical energy resource such as micro hydro is required. Micro hydro plant is an electrical power generators that uses water to rotate the turbine. This research designs a monitoring system for micro hydro plant. The monitored micro hydro plant employs water turbine that is constructed using bicycle pedal and a water pipe installed on the pedal . The pipe flows the water to energize the turbine. Turbine rotation will generate electricity. The amount of power resulted by generators depends on the number of turbine rotation. The power is used to turn on the lamp. Some sensors are used to monitor generator performance. Current, voltage, and rotation sensors are used to monitor the resulted current, voltage, the turbine rotation respectively. The output power is stored in the battery. The micro Arduino and the ethernet shield capture the monitored data and send it to the computers using Wi-Fi connection. Measurement results show that the output voltage produced by the generator is 10 Volts when the water volume is high. Finally, it is found that the micro hydro generator is able to supply 5 Watts to the load.]]>
<![CDATA[Priority Modeling for Public Urban Park Development in Feasible Locations using GIS, Intuitionistic Fuzzy AHP, and Fuzzy TOPSIS ]]>
<![CDATA[Arif Wicaksono]]>
<![CDATA[ Jurnal Rekayasa Elektrika Vol 17, No 4 (2021) ]]>
Publisher : <![CDATA[Universitas Syiah Kuala ]]>
Show Abstract
|
Download Original
|
Original Source
|
Check in Google Scholar
|
Full PDF (1851.662 KB)
|
DOI: 10.17529/jre.v17i4.23138
<![CDATA[As feasible locations of public urban park in Bogor Municipality have been acquired in a previous study, decision makers are urgently needed to be informed on which locations should be prioritized for public urban park (PUP) development. Therefore, this study aggregates four multi-spatial criteria for PUP development priority modeling, namely distance to slum neighborhood, accessibility, slope, and land value. These four criteria in form of vector datasets were weighted using intuitionistic fuzzy analytical hierarchy process (IF-AHP) to consider the hesitancy, vagueness, and fuzziness might arise from experts’ judgement as well as from multi-spatial data processing. Resulted criteria weights from IF-AHP show that accessibility weight 0.261, land value weight 0.259, distance to slum weight 0.255, and slope weight 0.225, respectively. Criteria weights were inputted into fuzzy technique for order preference by similarity to the ideal solution (TOPSIS) and geographic information system (GIS) to rank location priority. Results from fuzzy TOPSIS show that very high priority class which has the biggest CCi values range (0.654-0.76) provides 0.14 km2 area of feasible PUP development scattered in 10 locations. The biggest area for feasible PUP development is generated by medium priority class (CCi values 0.439-0.546) in 26 locations and approximately area of 0.38 km2.]]>
<![CDATA[Pengukuran Speed dan Impedansi Akustik pada Tanah Liat dengan Memanfaatkan Sinyal Echo Ultrasonik ]]>
<![CDATA[Lusiana Lusiana]]>;
<![CDATA[Agus Indra Gunawan]]>;
<![CDATA[Bima Sena Bayu Dewantara]]>
<![CDATA[ Jurnal Rekayasa Elektrika Vol 15, No 2 (2019) ]]>
Publisher : <![CDATA[Universitas Syiah Kuala ]]>
Show Abstract
|
Download Original
|
Original Source
|
Check in Google Scholar
|
Full PDF (6045.459 KB)
|
DOI: 10.17529/jre.v15i2.13815
<![CDATA[Each material has its own characteristics, which are represented by the value of speed/ultrasonic wave propagation speed (C) and acoustic impedance/material resistance (Ztl). One technique that can be used to obtain these characteristics is by applying ultrasonic testing. This technique utilizes two ultrasonic sensors as transmitter (UST) and receiver (USR) to get signal properties from each material. The measurement mechanism is nondestructive testing (NDT) where the material tested is not damaged so it does not change the character of the sample. In this research, material characteristics are represented by reflected signals from material (echo). To process the echo signal data and get the characteristics of the sample, we need a number of data processing algorithms such as Fast Fourier Transform (FFT), Peak Detection, and Grid Search. By processing echo from reflected signals, C and Ztl values can be obtained. From the experimental results obtained, the values of C and Ztl in sample 1 with a density of 1856.97573 g/m3 are C = 636 m/s and Ztl = 474640 Ns/m3, samples 2 with a density of 1792.94208 g/m3 of C = 491 m/s and Ztl = 408080 Ns/m3, while the sample 3 with a density of 1663.85025 g/m3 is C = 434 m/s and Ztl = 405639 Ns/m3. The value of material characterization shown that a dense clay also has higher C and Ztl.]]>
<![CDATA[Penggunaan Accelerometer MMA7361 sebagai Alternatif Pengukuran Lendutan pada Jembatan Secara Nirkabel Berbasis ATmega32 ]]>
<![CDATA[Mohd Syaryadhi]]>;
<![CDATA[Purwandy Hasibuan]]>;
<![CDATA[Suhardi Suhardi]]>
<![CDATA[ Jurnal Rekayasa Elektrika Vol 11, No 5 (2015) ]]>
Publisher : <![CDATA[Universitas Syiah Kuala ]]>
Show Abstract
|
Download Original
|
Original Source
|
Check in Google Scholar
|
Full PDF (1149.582 KB)
|
DOI: 10.17529/jre.v11i5.3215
<![CDATA[A bridge is planned and built with a certain capability against vehicles through it. The vehicles movement causes vibration and vertical deflection on certain parts of the bridge. If the vibration occurs continuously in a great value, then the bridge will be damaged sooner than had been planned. This research reports a design of a vertical deflection measuring system prototype on bridge, employing an accelerometer MMA7361 sensor which is controlledby ATmega32. The system was tested by manually loading the trial bridge with 1 m of length. The loading deflects down the bridge to maximum 15 cm from the reference point. Sensor readout data was sent wirelessly using ZigBee real time to computer in a graphical display for easy analysis. The research give an alternative method in vertical deflection measuring on the bridge that can be utilized by stakeholder in policy decision.]]>
<![CDATA[Desain Perancangan kwh meter Digital Berbasis Sistem SCADA pada Pelanggan Tegangan Menengah 20 KV di PT PLN (Persero) APJ Jember ]]>
<![CDATA[H.R.B. Moch. Gozali]]>
<![CDATA[ Jurnal Rekayasa Elektrika Vol 9, No 3 (2011) ]]>
Publisher : <![CDATA[Universitas Syiah Kuala ]]>
Show Abstract
|
Download Original
|
Original Source
|
Check in Google Scholar
|
Full PDF (1155.927 KB)
|
DOI: 10.17529/jre.v9i3.160
<![CDATA[SCADA is a very powerful new technology to be applied as a tele-metering. Planning of Digital KWH Meter based on SCADA at 20 kV medium voltage customer isselected in the PLN APJ Jember, where KWH Meters arewidely used today is the Landis Gyr ZMC405C type. But it is less reliable devices along with the development of technology today. KWH Meter ZMD405CT offers more features for modern, effective and efficient to be used by PLN in the future. Design of SCADA in ZMD405CT not use a lot of cable, so they are efficient in terms of cost. Meanwhile, software for data acquisition must be balanced with the KWH meter to be used, for electrical energy measurement accuracy on the customer side can be assured.]]>
<![CDATA[Sistem Pendukung Keputusan Rekomendasi Penerima Beasiswa Menggunakan Fuzzy Multi Attribut Decision Making (FMADM) dan Simple Additive Weighting (SAW) ]]>
<![CDATA[Candra Surya]]>
<![CDATA[ Jurnal Rekayasa Elektrika Vol 11, No 4 (2015) ]]>
Publisher : <![CDATA[Universitas Syiah Kuala ]]>
Show Abstract
|
Download Original
|
Original Source
|
Check in Google Scholar
|
Full PDF (505.093 KB)
|
DOI: 10.17529/jre.v11i4.2364
<![CDATA[Scholarship is a donation in term of financial assistance that is given to an individual, student or pupils. Even though, the target distribution of the scholarships is sometime not relevant. It is because the scholarship distribution has not yet used a tool or method to determine suitable scholarship recipients. For that reason, it needs to design a system to determine the scholarship recipients using Fuzzy Multi Attribute Decision Making (FMADM) and Simple Additive Weighting (SAW) method. FMADM method is used to looking for an alternative of some Alternatives with some criteria that determined before. Moreover, SAW method is used to rank the existing alternatives. The result of this research can be used as a tool to make decision with recommendation of the scholarship recipients.]]>
