Claim Missing Document
Check
Articles

ADVANCED TURBINE WORKING: IMPACT OF WINGLET ON VERTICAL WIND TURBINE DARRIEUS TIPE H Amir, Ahmad Ihwan; Soenoko, Rudy; Wijayanti, Widya; Setiadhi, David
International Journal of Mechanical Engineering Technologies and Applications Vol. 5 No. 1 (2024)
Publisher : Mechanical Engineering Department, Engineering Faculty, Brawijaya University

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.21776/MECHTA.2024.005.01.8

Abstract

In this study, the effect of winglets on improving the performance of type h darrieus wind turbines was investigated. The aim is to determine the most suitable winglet design and find out the magnitude of the increase in wind turbine performance. The method used is experimentation to find the RPM and torque used for calculate the TSR value and turbine power. From all the trial and error experiments, the type of blended winglet that best suited the characteristics of the VAWT. The experimental results show that the addition of blended winglet increases RPM of 13.6% in the 3-blade turbine and turbine it increases of 9% in the 4-blade turbine. The increase in average torque is 13.2% in a 3-blade turbine and 9.4% in a 4-blade turbine. The average increase in power coefficient is 11% in a 3-blade turbine and 9% in a 4-blade blade. In conclusion, the addition of blended winglets produces better torque and power compared to turbine models without winglets.
Pengaruh Perendaman Alkali, Kalium Permanganat, dan Hidrogen Peroksida terhadap Perubahan Diameter Serat Sabut Kelapa Sebagai Bahan Komposit Ramah Lingkungan Arsyad, Muhammad; Soenoko, Rudy
INTEK: Jurnal Penelitian Vol 6 No 1 (2019): April 2019
Publisher : Politeknik Negeri Ujung Pandang

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (783.074 KB) | DOI: 10.31963/intek.v6i1.1009

Abstract

This study aims to determine the effect of alkali treatment and hydrogen peroxide on the change in diameter of coconut fiber as an environmentally friendly composite material. This research was carried out with several stages, namely: preparation of materials and tools, treatments, measurement of diameter, analysis, and discussion. Materials and equipment used are coconut fiber, alkaline solution, hydrogen peroxide solution, distilled water, a set of immersion media, and digital microscopes. Coconut fiber was soaked in alkaline solution with 10% concentration for 1, 3, 5, 7, 9, and 11 hours, then dried in a furnace at 90oC for 5 hours. Furthermore, coconut fiber was soaked again in potassium permanganate solution with a concentration of 0.5% for 1, 3, 5, 7, 9, and 11 hours, then dried in a furnace at 90oC for 5 hours. Then the coconut fiber was soaked again in a hydrogen peroxide solution with a concentration of 10% for 1, 3, 5, 7, 9, and 11 hours, then dried in a furnace at 90oC for 5 hours. After that, using a digital microscope the diameter of coconut fiber is measured. Based on the measurement results, it was concluded that the diameter of coconut fiber was degraded in diameter after soaking in alkaline solution, potassium permanganate, and hydrogen peroxide. The highest percentage reduction in diameter was 58.08% in the third treatment.
ADVANCED TURBINE WORKING: IMPACT OF WINGLET ON VERTICAL WIND TURBINE DARRIEUS TIPE H Amir, Ahmad Ihwan; Soenoko, Rudy; Wijayanti, Widya; Setiadhi, David
International Journal of Mechanical Engineering Technologies and Applications Vol. 5 No. 1 (2024)
Publisher : Mechanical Engineering Department, Engineering Faculty, Brawijaya University

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.21776/MECHTA.2024.005.01.8

Abstract

In this study, the effect of winglets on improving the performance of type h darrieus wind turbines was investigated. The aim is to determine the most suitable winglet design and find out the magnitude of the increase in wind turbine performance. The method used is experimentation to find the RPM and torque used for calculate the TSR value and turbine power. From all the trial and error experiments, the type of blended winglet that best suited the characteristics of the VAWT. The experimental results show that the addition of blended winglet increases RPM of 13.6% in the 3-blade turbine and turbine it increases of 9% in the 4-blade turbine. The increase in average torque is 13.2% in a 3-blade turbine and 9.4% in a 4-blade turbine. The average increase in power coefficient is 11% in a 3-blade turbine and 9% in a 4-blade blade. In conclusion, the addition of blended winglets produces better torque and power compared to turbine models without winglets.
Lap Joint Carbon Steel ST 37 and Aluminum 6061 with Friction Stir Welding (FSW) Setiawan, Widia; Darmadi, Djarot B.; Suprapto, Wahyono; Soenoko, Rudy
Proceeding ISETH (International Summit on Science, Technology, and Humanity) 2016: Proceeding ISETH (International Conference on Science, Technology, and Humanity)
Publisher : Universitas Muhammadiyah Surakarta

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.23917/iseth.2361

Abstract

In this research, Aluminum 6061 and Carbon steel ST 37 sheet were lap joined by friction stir welding. A hardened medium carbonese steel (EMS 45) was used as rotary Probe. The microstructures of the joining inter-metallic compounds were observed by scanning electron microscopy, microstructure photograph, and micro-hardness tests. The joint strength was evaluated by shear stress tests. The experiment was performed with varied length of pin probe 6, 7, and 8 mm, equal rotational speed of 2500 rpm, and welding speed (15 mm/minutes). The Inter-metallic compounds of aluminums sheet was cut off the pin probe and the mixture on the Carbon steel ST 37. Intermetallic compounds were analyzed on its micro sructure in this region aluminum and carbon steel mixed, the value joint tensile shear 6.2KN.
MINIMASI WASTE UNTUK PERBAIKAN PROSES PRODUKSI KANTONG KEMASAN DENGAN PENDEKATAN LEAN MANUFACTURING Setiyawan, Danang Triagus; Soeparman, Sudjito; Soenoko, Rudy
JEMIS (Journal of Engineering & Management in Industrial System) Vol. 1 No. 1 (2013)
Publisher : Industrial Engineering Department, Faculty of Engineering, Universitas Brawijaya

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.21776/ub.jemis.2013.001.01.2

Abstract

Packaging Factory have activities in  bag production. In order to increase the productivity, the company should manage the activities to increase valued added and decrease several waste. This study was purpose for analyzed the caused problems of waste, and give recommendation for minimizing the waste.  The problem solving at the study was using lean manufacturing concept approach.  The waste identification began with identification of  current state value stream mapping with weighting the waste in order to  understand the root of problem within production process.  The detail mapping selection was using Value Stream Analysis Tools (VALSAT).  Root Cause Analysis was used in order to understanding the root of problem for production process followed by FMEA for understanding the improving priority which has to be done. From the data analysis result, we found that the most dominant waste order is defect, waiting,  inventory, excessive transportation.The mapping detail used for analysis process as Process Activity Mapping Supply Chain Response Matrix and Quality Filter Mapping. From the result of study we found the decreasing of production time from 138.4 minute to 119.4 minute.  Decreasing lead time process could reach 13,7% comparing before the recovery step. 
HAZARD ANALYSIS AND CRITICAL CONTROL POINT (HACCP) PRODUKSI MALTOSA DENGAN PENDEKATAN GOOD MANUFACTURING PRACTICE (GMP) Hermansyah, Muhammad; Pratikto, Pratikto; Soenoko, Rudy; Setyanto, Nasir Widha
JEMIS (Journal of Engineering & Management in Industrial System) Vol. 1 No. 1 (2013)
Publisher : Industrial Engineering Department, Faculty of Engineering, Universitas Brawijaya

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.21776/ub.jemis.2013.001.01.3

Abstract

This study describes a series of treatment processes and functions of each stage in the production process and the conditions of maltose product with GMP parameters are implemented by the application of HACCP is equipped with Work Instructions CCP. The study was conducted with qualitative data analysis, by comparing the data and the results of observations with the relevant literature, in the form of articles, research journals, and generally accepted standards, although the calculation of GMP with some quantitative data. Through the resulting composition of the seven studies document the HACCP assessment, include: (1) Establishment of HACCP team, (2) Description of Products and Processes, (3) Purposes and Consumer Products, (4) Process Flow Diagram, (5) Hazard Identification, (6 ) Determination of the CCP, and (7) Worksheet CCP. Documents 1, 2, and 3 have been prepared to review and revise the existing old documents, while the documents 4 to 7 is a new document. The seven documents is then also equipped with Work Instruction documents CCPs to facilitate labor in monitoring and control of critical control points (CCPs). The results showed maltose production process generally consists of four main phases, including: likuifikasi, saccharification, purification (filtration and ion processes), and concentration.
PENGUKURAN KINERJA PADA PERUSAHAAN FURNITURE DENGAN MENGGUNAKAN METODE PERFORMANCE PRISM DAN ANALYTICAL HIERARCHY PROCESS Widiyawati, Sri; Soeparman, Sudjito; Soenoko, Rudy
JEMIS (Journal of Engineering & Management in Industrial System) Vol. 1 No. 1 (2013)
Publisher : Industrial Engineering Department, Faculty of Engineering, Universitas Brawijaya

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.21776/ub.jemis.2013.001.01.6

Abstract

Performance measurement method, Performance Prism, was used to improve performance measurement method in this furniture company. Until now, performance measurement system in this company  haven’t represented overall organizational performance since it only used performance measurement based on individual ability. Performance measurement using Performance Prism method was used because it could reflects the needs and desire of each identified stakeholder within company. This performance measurement is an integrated measurement, encompassing all company aspects (stakeholder) which related with stakeholder satisfaction and stakeholder contribution for the company. Performance measurement in this study also supported by several other methods such as weighting with Analytical Hierarchy Process (AHP) to determine priority scale of each KPI, Scoring System using Objectives Matrix (OMAX) and Traffic Light System to determine total index value of company in corporation level and category of those indices. Results of performance measurement in this company using Performance Prism indicated 79 KPI’s consist of 17 KPIs on Investor perspective, 16 KPI’s on Customer perspective, 16 KPI’s on Employee perspective, 15 KPI’s on Supplier perspective and 15 KPI’s on Regulator perspective. Based on performance measurement calculation using Objective Matrix and Traffic Light System, it obtained total index value 5,8364. This showed that performance of this furniture company  still yet to reach desirable performance thus it would need some improvement in this matter.
INTEGRASI SERVQUAL DAN QUALITY FUNCTION DEPLOYMENT UNTUK PENGUKURAN KUALITAS LAYANAN (STUDI KASUS: PROGRAM STUDI PENDIDIKAN TEKNIK MESIN, UNIVERSITAS PALANGKA RAYA) Wiyogo, Wiyogo; Surachman, Surachman; Soenoko, Rudy; Setyanto, Nasir Widha
JEMIS (Journal of Engineering & Management in Industrial System) Vol. 1 No. 1 (2013)
Publisher : Industrial Engineering Department, Faculty of Engineering, Universitas Brawijaya

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.21776/ub.jemis.2013.001.01.4

Abstract

Services in Program Studi Pendidikan Teknik Mesin (PSPTM) still has drawbacks, among other complaints for cleanliness wc, and class. This indicates or identifies a student dissatisfaction against poor service. Service has 5 dimensions, namely tangible dimension, responsiveness, reliability, assurance, empathy is to be seen to solve the existing problems. Analytical techniques is used SERVQUAL approach and Quality Function Deployment (QFD). Calculation results gap between perception and expectation would then be prioritized using the Pareto principle to acquire the attributes which are important for repair. In the academic service attributes availability of toilets has the highest gap value at -2,70 , while at the administrative service, on-time attendance officer has a gap value of -1,74. From the House of Quality on academic services obtained 33 attributes as recommendations for improvements such as fixing a broken toilet, maximize existing bandwidth. Meanwhile, in the administrative services generated 21 attributes priority, such as scheduling workers, implementing SOP service, encourage officers to be more proactive in serving students. 
PERBAIKAN FASILITAS KERJA MEMBATIK DENGAN PENDEKATAN ERGONOMI UNTUK MENGURANGI MUSCULOSKELETAL DISORDERS Sanjaya, Krishna Tri; Wahyudi, Slamet; Soenoko, Rudy
JEMIS (Journal of Engineering & Management in Industrial System) Vol. 1 No. 1 (2013)
Publisher : Industrial Engineering Department, Faculty of Engineering, Universitas Brawijaya

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.21776/ub.jemis.2013.001.01.7

Abstract

Small and middle enterprises  have been the important part of the economic of a nation or a local. Karang Write-Batik is one industrial center which is located at Karang Village, Semanding Subdistrict, Tuban District. Early observation shows that various processes within the production of Write-Batik are conducted without considering ergonomic aspects, such as work method and work facility. It may result in complaint and even muscle injury which is called Musculoskeletal Disorders (MSD’s) Many pronlem of pain perceived by workers are caused by less ergonomic work position or work posture. It may also be evident because the less correspondence between work equipment and workers’ anthropometry size. To measure workers’ musculoskeletal injured, the author uses Standard Nordic Questionnaire (SNQ) and to assess work posture, Quick Exposure Check (QEC) is used. The reduction of workers’ musculoskeletal injuredt can be realized by improving work facility based on workers’ anthropometry size. Result of early measurement of exposure level of several parts of body indicates that the exposure level of the back is 26, while that of the arm is 30, that of the hand wrist is 26, and that of the neck is 16. After the improvement of work facility, workers’ complaint is reduced and so is exposure level. The exposure level with the improved work facility is shown as follows: the exposure level of the back is 22, while that of the arm is 22, that of the hand wrist is 22 and that of the neck is 14.
ANALISIS PENGUKURAN KINERJA RUMAH SAKIT DENGAN MENGGUNAKAN METODE PERFORMANCE PRISM Cahyawati, Amanda Nur; Pratikto, Pratikto; Soenoko, Rudy
JEMIS (Journal of Engineering & Management in Industrial System) Vol. 1 No. 1 (2013)
Publisher : Industrial Engineering Department, Faculty of Engineering, Universitas Brawijaya

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.21776/ub.jemis.2013.001.01.1

Abstract

Good performance measurement is a measurement that covers all aspects of the stakeholders include investors, customer, employees, suppliers, regulators and communities. There is only one performance measurement that covers all aspects of stakeholders by using performance prism methods. Hospital X Malang is one example of an organization that use traditional performance measurement. Performance measurement has been done based on the financial side only, while the other aspects less noticed. Performance prism in this study aided by Analytical Hierarchy Process (AHP) and scoring system which includes objectives matrix and traffic light systems. The results was obtained 99 KPI consists of 17 investors, 35 customer, 16 employee, 15 supplier and 16 regulators and the community. Total index of the objective matrix is 7.9 and based on the traffic light system is in the yellow category.
Co-Authors A.A. Ketut Agung Cahyawan W Abdul Wahid Nuruddin Achmad Noerkhaerin Putra Adrian Maidangkay Agustinus Deka Betan Ahmad Hamim Su’udy Alfeus Sunarso Amanda Nur Cahyawati Amir, Ahmad Ihwan Anindito Purnowidodo Arif Setia Budi, Sofyan Arif Setia Budi, Sofyan Arthur Yanny Leiwakabessy Asroful Anam Azamataufiq Budiprasojo Bachri, Gufron Saiful Danang Triagus Setiyawan Denny Widhiyanuriyawan Dewa Ngakan Ketut Putra Negara Djarot B. Darmadi, Djarot B. Djoko Sutikno Eko Siswanto Febi Rahmadianto Fery Putra PT Frederik Demmatacco Gunawan Pakki Hadi Saroso Halim Zaini, Halim Hermawan, Yuni Heru Suryanto I Ketut Suarsana I.K.G. Wirawan I.N.G. Wardana Indrayadi, Bambang ING Wardana Josef Matheus Kris Witono Krishna Tri Sanjaya Misbachudin, Muh Misbachudin Moch. Agus Choiron Muhammad Arsyad Muhammad Hermansyah Murti Astuti Murty Astuti Na'ali, Sidi Nanse Henny Pattiasina Nanulaitta, Nevada Mario Nasir Widha Setyanto Nevada M.J. Nanulaitta Noorsakti Wahyudi Nugraha, Arif Yunizar Nurkholis Hamidi Panca Mudjirahardjo Ponco Muchamad Nur Cahyo Pratikto Pratikto Purnomo B. Santoso Purnomo Budi Santoso Putu Wijaya Sunu Raden Arief Setyawan Reinaldo Jr. F. B.B Richard A.de FRETES Richard Pietersz Ridho Dwi Syahrial Rio L Lukodono Rio Prasetyo Lukodono Romels C. A. Lumintang Ronny Tuhumena Setiadhi, David Setiawan, Widia Slamet Wahyudi Soeprapto, Wahyono Soeprapto, Wahyono Sonief, Achmad As´ad Sri Widiyawati Sudjito Soeparman Sugiarto S Sugiono Sugiono Sujatmiko Sujatmiko Sunu, P.W. Surachman Surachman Surya Irawan, Yudy Surya Irawan, Yudy Sutrisno, Sutrisno Syahrizal Syahrizal Teguh Dwi Widodo Wahyono Suprapto Widhiyanuriyawa, Denny Widya Wijayanti Wiluddyana Ghoisi Nafida Wiyogo Wiyogo Yudy Surya Irawan Yuni Hermawan Yurianto Yurianto Yusuf Novrianto