Didik Setiyo Widodo
Chemistry Department, Faculty Of Sciences And Mathematics, Diponegoro University Jl. Prof. Soedarto, SH., Tembalang, Semarang

Published : 56 Documents Claim Missing Document
Claim Missing Document
Check
Articles

Pengayaan Yodium dan Kadar NaCl pada Garam Krosok menjadi Garam Konsumsi standar SNI Enrichment of Iodium and Sodium Cloride in the Traditional Salt become Consumtion Salt INS Standard M. Nur; I. Marhaendrajaya; Sugito Sugito; T. Windarti; Arnelli Arnelli; R. Hastuti; A. Haris; W. H. Rahmanto; Didik Setiyo Widodo; F. Ariyanto; Z. Muhlisin; J. E. Suseno; E. Setiawati; H. Sutanto; Priyono Priyono; M. Izzati; R. Hariyati; S. Tana; B. Raharjo; D. Ispriyanti; Farikhin Farikhin; A. Rusgiyono; Suhartono Suhartono
JURNAL SAINS DAN MATEMATIKA Volume 21 Issue 1 Year 2013
Publisher : JURNAL SAINS DAN MATEMATIKA

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (3994.464 KB)

Abstract

This research has been carried out in the quality improvement of traditional salt (krosok salt) into salt consumption for the Indonesian National Standard. This report is devoted to the elevated levels of NaCl and KIO3. Increased levels of NaCl and Iodine (represented by KIO3) is done by washing the salt with the traditional clothes washer with two rounds and by using water with saline solution at 22-24 Be (known as the old water). Traditional salt taken from three districts, such as Pati District, Jepara District, and Rembang District. We found that the concentration of NaCl in the treatment salt maximum is  96 % and Iodium or present of KIO3 is 40 ppm.   Key words: Salt,  traditional, INS, Consumtion, NaCl, KIO3
Removal of Methylene Blue Using Used Paper Powder Ghina Labiebah; Gunawan Gunawan; Muhammad Cholid Djunaidi; Abdul Haris; Didik Setiyo Widodo
Jurnal Kimia Sains dan Aplikasi Vol 22, No 1 (2019): volume 22 Issue 1 Year 2019
Publisher : Chemistry Department, Faculty of Sciences and Mathematics, Diponegoro University

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (2330.384 KB) | DOI: 10.14710/jksa.22.1.23-28

Abstract

Methylene blue removal by adsorption method had been done in batch method using adsorbent of used paper powder. Adsorption parameters covering adsorbent doses, contact times, pH, adsorbate concentrations and adsorption isotherm as well as desorption study of the absorbed methylene blue were evaluated. The results showed the highest adsorption of methylene blue was obtained at an optimum adsorbent dose, for 30 min at pH > 9. The maximum adsorption capacity of 30.77 mg/g was obtained with Langmuir isotherm model. While the effective methylene blue desorption on the used paper powder adsorbent was obtained c.a. 0.27 mg/g at pH 1.
Preparation of thin layer CuO from Cu2O using the Spin Coating Method at Various Annealing Temperature and Number of Dripping for Photoelectrochemical Water Splitting Eka Pratista; Gunawan Gunawan; Didik Setiyo Widodo
Jurnal Kimia Sains dan Aplikasi Vol 23, No 11 (2020): Volume 23 Issue 11 Year 2020
Publisher : Chemistry Department, Faculty of Sciences and Mathematics, Diponegoro University

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (3240.913 KB) | DOI: 10.14710/jksa.23.11.390-395

Abstract

A thin layer preparation of CuO from Cu2O powder using Fehling's solution for photoelectrochemical applications has been performed. The research was focused on studying the effect of annealing temperature and the number of drops on the performance of CuO thin layer semiconductors from Cu2O powder prepared by spin coating with a rotation rate of 500 rpm for 15 seconds. The thin layers were treated with annealing with temperature variations of 300°C, 400°C, and 500°C for 1 hour and variations in the number of drops of 10, 20, and 50 drops. The CuO thin layer was tested in a photoelectrochemical process as a photocathode to split water with a simulated light of 1.5 AM (100 mW/cm2). The process of splitting water as a method of producing hydrogen energy by photoelectrochemistry is assisted by semiconductors, such as CuO, in an electrolyte solution to capture photons and drive the water-splitting reactions. Copper (II) Oxide (CuO) is a p-type semiconductor with a band gap of 1.2-2.5 eV, which can be used as a photocathode. The optimum photoelectrochemical measurement results were obtained at an annealing temperature of 400°C and 50 drops with a current density of 0.584 mA/cm2 at a potential of 0.2 V versus the Reversible Hydrogen Electrode (RHE). The results of the Scanning Electron Microscopy (SEM) analysis show that the morphology of the oxide is spherical. Energy dispersive X-ray (EDX) analysis displays that the sample contained 51.46% and 48.54% of Cu and O, respectively. The X-ray diffraction pattern (XRD) analysis shows that the oxide grain size is 44.137 nm.
Pengaruh Penambahan Serbuk Titanium Dioksida (TiO2) dalam Fotoelektrokatalisis Fenol dengan Elektroda PbO2/Pb Ardi Ariawan; Muhammad Cholid Djunaidi; Didik Setiyo Widodo
Jurnal Kimia Sains dan Aplikasi Vol 14, No 3 (2011): Volume 14 Issue 3 Year 2011
Publisher : Chemistry Department, Faculty of Sciences and Mathematics, Diponegoro University

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (442.795 KB) | DOI: 10.14710/jksa.14.3.64-68

Abstract

Fenol merupakan salah satu pencemar perairan yang beracun, dapat terakumulasi dan stabil. Salah satu metode yang efektif untuk mendegradasi fenol adalah fotoelektrokatalisis. Tujuan dari penelitian ini adalah untuk mendegradasi fenol dengan metode fotoelektrokatalisis menggunakan elektroda PbO2/Pb, mengetahui pengaruh penambahan TiO2dan membandingkan metode fotoelektrokatalisis dengan fotokatalisis dalam degradasi fenol. Larutan fenol 100 mL dielektrolisis dengan potensial 5 V selama 8 jam dan ditambah 0,8 g TiO2 dan dipapar sinar UV. Kemudian larutan sampel dianalisis dengan spektrometer UV-Vis. Untuk memperoleh potensial kerja dilakukan elektrolisis terhadap blanko (akuades ditambahkan Na2SO4 berlebih). Setelah itu dilakukan variasi potensial, variasi waktu fotoelektrokatalisis hingga 10 jam serta variasi penambahan TiO2 hingga 1,0 g. Penambahan TiO2 sebanyak 0,8 g pada fotoelektrokatalisis fenol menaikkan persentase degradasi fenol dari 79,31% menjadi 94,05%. Degradasi fenol ditunjukkan dengan terjadinya penurunan absorbansi pada panjang gelombang 270 nm. Metode fotoelektrokatalisis lebih efektif dalam mendegradasi fenol dalam larutan daripada fotokatalisis.
Pemisahan Logam Perak Dalam Limbah Cair Menggunakan Membran Cair Emulsi (ELM) Dengan Senyawa Pembawa Sinergi D2EHPA Muhammad Cholid Djunaidi; Danang Subarkah Hadikawuryan; Didik Setiyo Widodo; Nesti Dewi Maharani
Greensphere: Journal of Environmental Chemistry Vol 1, No 1 (2021): Volume 1 Issue 1 tahun 2021
Publisher : Universitas Diponegoro

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (790.958 KB) | DOI: 10.14710/gjec.2021.10899

Abstract

Perak adalah logam yang digunakan secara luas dalam berbagai industri, meliputi fotografi (bahan dasar film dan kertas foto), elektronik, perhiasan, campuran logam (alloy) penghambat korosi, dan sebagainya sampai keskala laboratorium. Kandungan perak dalam limbah sebesar lebih dari 2000 mg/Lyang berpotensi menyebabkan toksisitas lingkungan dan kesehatan bagi makhluk hidup. Oleh karena itu, perlu dilakukan pemisahan logam perak dalam limbah dengan metode Emulsion Liquid Membrane (ELM) dengan campuran pembawa D2EHPA-TBP yang memiliki efektivitas dan selektivitas yang tinggi terhadap ion logam Ag. Produk perak yang didapatkan sebagai penyedia perak kedua. Hasil yang didapatkan dengan penggunaan pembawa D2EHPA-TBP lebih efektif untuk mengambil perak dari limbah daripada larutan Ag+. Pembawa D2EHPA-TBP menggunakan perak tiosulfat (sinergi) relatif selektif daripada Cu(II) dan Cr(VI) dengan persen pengambilan perak sebesar 94,93%.Kata Kunci: ELM; Logam Perak; selektif; D2EHPA
DEKOLORISASI REMAZOL BLACK B DENGAN PENDEKATAN REDOKS DALAM REAKTOR SKALA GANDA ( SCALE UP REACTOR ) Ayu Fadhilatul Rukmana; Didik Setiyo Widodo; Muhammad Cholid Djunaidi
Greensphere: Journal of Environmental Chemistry Vol 1, No 2 (2021): Volume 1 Issue 2 tahun 2021
Publisher : Universitas Diponegoro

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (346.808 KB) | DOI: 10.14710/gjec.2021.12869

Abstract

RBB yang banyak digunakan dalam industri tekstil merupakan salah satu pencemar yang potensial menimbulkan masalah lingkungan. Telah dilakukan penelitian dekolorisasi larutan remazol black B (RBB) dengan metode Fenton termodifikasi Pb. Penelitian ini bertujuan untuk mengetahui kondisi optimum dalam proses dekolorisasi, mengevaluasi tingkat dekolorisasi dalam scale up reactor, dan menentukan karakteristik reaktor dekolorisasi. Pada penelitian ini dilakukan beberapa perlakuan, dalam skala laboratorium menggunakan Pb dari limbah baterai dan H2O2 pada kondisi pH tertentu kemudian ditentukan kondisi optimumnya. Perlakuan kedua, pada pewarna RBB skala ganda ditambahkan reagen Pb, H2O2dan pH optimum. Pengujian penurunan intensitas warna dilakukan dengan spektrofotometer UV-Vis. Hasil penelitian menunjukkan bahwa larutan remazol black B dapat didekolorisasi menggunakan metode Fenton dengan memodifikasi penggunaan ion Fe2+ dengan Pb. Data menunjukkan pH netral optimum pada dekolorisasi zat warna menggunakan 1 g Pb dan H2O2 10%. Persentase dekolorisasi mencapai 93,3% yang menunjukkan potensi metode ini dalam dekolorisasi RBB. Efektivitas dekolorisasi larutan RBB 50 ppm mencapai tertinggi pada kondisi reaktor tertentu dengan spesifikasi ukuran 100 mL H2O2 10%, massa Pb 1 g, waktu dekolorisasi 4 jam (tanpa pengadukan). Proses telah menurunkan nilai COD secarea signifikan dari 4.027,7 mg/L menjadi 65,37 mg/L, atau sebasar 98,37%.
Synthesis of Lead Oxide Using the Oxidizing Agent (NH4)2S2O8 with Variaous Amounts of NaOH for Decolorization of Remazol Black B Solution Meiske Erdinarini Anggita; Abdul Haris; Didik Setiyo Widodo
Jurnal Kimia Sains dan Aplikasi Vol 25, No 12 (2022): Volume 25 Issue 12 Year 2022
Publisher : Chemistry Department, Faculty of Sciences and Mathematics, Diponegoro University

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.14710/jksa.25.12.436-441

Abstract

In this study, the lead oxide has been successfully synthesized using oxidizing agents (NH4)2S2O8 and applied to decolorize the Remazole Black B (RBB) solution. Lead oxide was synthesized by the batch method through the mechanism of reduction-oxidation and characterized using SEM-EDX and XRD. Decolorizing RBB solution was performed using a modified Fenton method. This study aims to determine the optimum performance of RBB decolorization from lead oxide. The results showed that the crystal formed contains Pb and O. Pb oxide obtained was α-PBO2 with the orthorhombic crystal system. Based on characterization, the lead oxide obtained has a surface morphology of coral flowers-like. Synthesis utilizing equilibrium composition (1:2) and a drying temperature of 100°C yielded Pb oxide, which has a better potential as a modifier in RBB decolorization with a decolorization percentage of 80.07%. The process was then carried out for advanced synthesis less and excess of molar variations. The ratio of lead oxide: NaOH (1:4) showed optimum performance in decolorizing RBB with a decolorization percentage of 80.07 %.
STUDI SIFAT FISIKOKIMIA MEMBRAN KITOSAN TERMODIFIKASI HEPARIN DAN POLIETILEN GLIKOL (PEG) Retno Ariadi Lusiana; Diana Pratiwi Rusendi; Didik Setiyo Widodo; Abdul Haris; Ahmad Suseno; Gunawan Gunawan
Analit: Analytical and Environmental Chemistry Vol 4, No 2 (2019): Analit: Analytical and Environmental Chemistry
Publisher : Universitas Lampung Jl. Prof. Dr. Sumatri Brojonegoro No.1 Bandar Lampung

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (538.15 KB) | DOI: 10.23960/aec.v4i2.2019.p1-13

Abstract

Pembuatan material membran diarahkan agar menghasilkan membran dengan karakter sesuai seperti pori-pori kecil yang seragam, kuat secara mekanik, dan mempunyai ketahanan pada tekanan tinggi. Kitosan merupakan salah satu biopolimer yang dapat digunakan sebagai bahan membran. Penelitian ini mengembangkan membran berbasis kitosan dan menganalisis karakteristik fisiko-kimia dari membran. Keberhasilan reaksi modifikasi dianalisis dengan  FTIR dan karakteristik  fisika dianalisis melalui uji serapan air,  pengembangan air, porositas, ketahanan pH, dan hidrofilisitas. Spektra FTIR yang diperoleh menunjukkan bahwa modifikasi membran kitosan telah berhasil dilakukan. Modifikasi melalui pemaduan PEG dan reaksi cangkok dapat meningkatkan persentase serapan air, daya pengembangan, porositas, dan meningkatkan hidrofilisitas membran. Sementara, ketahanan membran pada berbagai kondisi pH, membran kitosan termodifikasi lebih tinggi dibanding membran kitosan.http://dx.doi.org/10.23960/aec.v4.i2.2019.p01-13
Pengaruh Ligan NH3 pada Pengambilan Logam Tembaga dari Serpihan Sisa Produksi Kuningan Kabupaten Pati Secara Elektrolisis Santi Hermayanti; Didik Setiyo Widodo; Rum Hastuti
Jurnal Kimia Sains dan Aplikasi Vol 14, No 2 (2011): Volume 14 Issue 2 Year 2011
Publisher : Chemistry Department, Faculty of Sciences and Mathematics, Diponegoro University

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (336.111 KB) | DOI: 10.14710/jksa.14.2.54-57

Abstract

Telah dilakukan penelitian tentang pengaruh ligan NH3 pada pengambilan logam tembaga dari serpihan sisa produksi kuningan Kabupaten Pati secara elektrolisis. Serpihan sisa produksi kuningan mengandung logam mayor yakni tembaga(Cu), seng(Zn), dan logam minor yakni Timbal(Pb), dan Timah (Sn). Penambahan ligan tertentu dapat meningkatkan kuantitas dan kualitas endapan. Penelitian ini meliputi 3 langkah, yaitu destruksi serpihan sisa produksi kuningan, elektrolisis dan analisis dengan AAS. Larutan elektrolit yang digunakan adalah larutan hasil destruksi serpihan kuningan yang diencerkan 1000 kali. Variabel penelitian ini adalah waktu elektrolisis yaitu 30, 60, 90, dan 120 menit pada sampel tanpa dan dengan penambahan NH3. Hasil penelitian menunjukkan bahwa berat endapan 19,54 mg tanpa ligan NH3 dan 20,58 mg dengan ligan NH3 pada waktu elektrolisis 120 menit. Kemurnian endapan tembaga pada waktu elektrolisis 30 menit pada sampel tanpa penambahan NH3 adalah 62,80% dan dengan penambahan NH3 72,46%.
Electrosynthesis of α-Fe2O3 in a Fe(s)|KCl(aq)||H2O(aq)|C(s) System Nia Siskawati; Didik Setiyo Widodo; Wasino Hadi Rahmanto; Linda Suyati
Jurnal Kimia Sains dan Aplikasi Vol 21, No 4 (2018): volume 21 Issue 4 Year 2018
Publisher : Chemistry Department, Faculty of Sciences and Mathematics, Diponegoro University

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (2041.727 KB) | DOI: 10.14710/jksa.21.4.182-186

Abstract

Research on α-Fe2O3 electrosynthesis has been performed in the system Fe(s)|KCl(aq)||H2O(aq)|C(s). Electrolysis produces a reduction and oxidation reaction so that it requires a proper electrolyte concentration in the process. The purpose of this study was to obtain α-Fe2O3 compounds, determine the products produced by FTIR and XRD, and determine the size of the grains of products with PSA. Electrolysis method of two compartment was used in this research. The cathode and anode compartments was connected with the salt bridge. In anode chamber containing electrolyte solution KCl was varied (0,2 M; 0,3 M; 0,4 M; 0,5 M and 0,6 M) whereas at cathode space there was aquades. Electrolysis was run at 12 V for 8 hours. The electrolysis result was then calcined for two hours at a temperature of 500°C. The resulting product was then characterized by (FTIR, XRD, and PSA). The resulting product is then characterized by (FTIR, XRD, and PSA). The results showed that brown ferrihydrite was obtained in a concentration of 0.2 M; 0.3 M; 0.4 M; 0.5 M and 0.6 M were 21.6 mg; 24.1 mg; 34.5 mg; 39.4 mg and 62.4 mg respectively. Ferrihydrite produced from electrolysis of KCl 0.4 M concentration was dark red The XRD results show the presence of α-Fe2O3 and PSA results show that the α-Fe2O3 particle size is 151.57-171.25 nm.
Co-Authors A. Haris A. Rusgiyono Abdul Haris Abdul Haris Abdul Haris Abdul Haris Afrianti Reza Kusuma Agus Hartanto Ahmad Suseno Anggun Yuliani Ardi Ariawan Arnelli Arnelli Aulannisa Elqudsy Ayu Fadhilatul Rukmana B. Raharjo Byan Pratama D. Ispriyanti Dahlia Nurmalasari Danang Subarkah Hadikawuryan Desvita Sari Dewi Martina Diana Pratiwi Rusendi E. Setiawati Eka Pratista Eko Sugiharto Endang Tri Wahyuni Endang Tri Wahyuni F. Ariyanto Fardhani, Dea Ayu Fithri Noorikhlas Fitra Nilla Sari Galih Widayanti Ghina Labiebah Ginanjar Argo Pambudi Gunawan Gunawan Gunawan Gunawan Gunawan Gunawan H. Sutanto Hasan Muhtar Helena Krey Hera Yulianti I Gusti Ngurah Antaryama I. Marhaendrajaya Ilmi Muftiana Ilyas Bachtiar Ina Triavia Ines Ayu Handayani Ismiyarto Ismitarto J. E. Suseno Juwanda, Farikhin Kaviani Suciana Alifah Khabibi Khabibi khabibi Khabibi Kharisma Luthfiaratri Rahayu Kusumaningati, Marchelina One Laila Ika Anggraini Lina Yuanita Linda Suyanti Linda Suyati Linda Suyati Lutfia Apipah M. Izzati M. Nur Marcelinus Christwardana Mei Viantikasari Meiske Erdinarini Anggita Muhamad Abduh Hasibuan Muhammad Cholid Djunaidi Nawatuttuqoh Nawatuttuqoh Nesti Dewi Maharani Nia Siskawati Nies Suci Mulyani Nor Basid Adiwibawa Prasetya Pardoyo Pardoyo Patmawati Patmawati, Patmawati Prihastuti Santini Laksmi Dewi Priyono Priyono R. Hariyati R. Hastuti Rahmad Nuryanto Rahmad Nuryanto Rahmad Nuryanto Retno Ariadi Lusiana Riska Nurfida Annisa RR. Ella Evrita Hestiandari Rum Hastuti Rusendi, Diana Pratiwi S. Tana Santi Hermayanti Siti Elin Huriati Sonita Afrita Purba SRI ISDADIYANTO Suberta, Melani Sugito Sugito Suhartana Suhartana Suhartono Suhartono T. Windarti Titi Agustin Titik Darmawanti Ulfa Wiwit Chasanah Umi Fadilah, Umi Vinsencius Guntur Pandu Marcellino W. H. Rahmanto Wahyu Adi Kristanto Wahyu Adi Kristanto Wasino Hadi Rahmanto Wawan Prasetyo Wilman Septina Yudhi Richard Z. Muhlisin