Garuda - Garba Rujukan Digital

Analysis of Exhaust Gas Heat Utilization in Waste Heat Recovery Power Generator at Indarung V Factory PT Semen Padang Mayang Safira; Melda Latif; Zaini Zaini; Aulia Aulia; Mumuh Muharam; Waweru Njeri
Andalas Journal of Electrical and Electronic Engineering Technology Vol. 3 No. 1 (2023): May 2023
Publisher : Electrical Engineering Dept, Engineering Faculty, Universitas Andalas

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.25077/ajeeet.v3i1.34

Increasing energy efficiency in the cement production process at PT Semen Padang is carried out by reusing exhaust gas to produce electricity using Waste heat recovery power generation (WHRPG) with a capacity of 8.5 MW. WHRPG is a technology for utilizing exhaust gas heat as a source of heat energy to heat feed water into steam by using a suspension preheater (SP) boiler and air quenching cooler (AQC) boiler. This study aims to calculate the power potential of the steam heat influenced by the steam temperature and the mass flow rate of the steam produced by the boiler, to calculate the efficiency of the boiler using the direct method by comparing the boiler output heat against the boiler input heat, to calculate the turbine efficiency based on the difference between the steam enthalpy enter the turbine against the steam enthalpy out of the turbine and the isotropic enthalpy of the steam out of the turbine and to calculate the power generated by WHRPG at PT Semen Padang. The results obtained in this study are the total potential power of steam heat is 19.778 MW, the boiler AQC efficiency is 70.30%, the boiler SP efficiency is 94.04% and the turbine efficiency is 78.64%. The electricity generated by PT Semen Padang's WHRPG is 3.70 MW.

Potensi Energi Listrik Pada Gas Buang Sepeda Motor Melda Latif; Nuri Hayati; Uyung Gatot S Dinata
Jurnal Rekayasa Elektrika Vol 11, No 5 (2015)
Publisher : Universitas Syiah Kuala

The fossil energy sources dwindling due to the many needs, especially in industrial and automotive sectors which are the largest energy users and the highest waste heat-producing. This causes many alternative energy sources are developing, included thermal energy utilization. The research utilized waste heat energy from motorcycle exhaust pipe into electrical energy with using Thermo Electric Generator (TEG). By using the thermocouple principle, difference of temperature between hot and cold side of TEG resulted voltage. Testing was conducted with three points are on head, body and mouth of the exhaust pipe. The maximum output voltage is generated in the head is greater than the other positions. At the head of exhaust, the maximum output voltage which is generated by 1 modul, 2 modules and 3 modules of TEG on each other is 1.26 V, 2.27 V and 3.43 V respectively.

Penerapan Sampah Buah Tropis untuk Microbial Fuel Cell Melda Latif; Arif Dwi Fajri; Mumuh Muharam
Jurnal Rekayasa Elektrika Vol 16, No 1 (2020)
Publisher : Universitas Syiah Kuala

Microbial Fuel Cell (MFC) is one tool that uses microbes to produce electrical energy. The main components of MFC support are anodes, cathodes, and salt bridges. In this paper, the application of tropical fruit waste to MFC is presented. Tropical fruit waste used here are pineapples, oranges, bananas, watermelons, mangos, and papayas. The fruit waste is extracted and fermented to produce microbial. The microbial produces ions attached to the anode. Measurement of system current and voltage is carried out using a digital multimeter. In pineapple substrate MFC, Voc has a maximum of 485 mV, maximum current density is 163 mA/m2 and maximum power density of 11mW/m2. The orange substrate obtained Voc maximum of 805 mV, maximum current density of 661 mA/m2 and maximumpower density of 62 mW/m2. Voc banana substrate has a maximum of 312 mV, maximum current density of 118 mA/m2 and maximum power density of 5.9 mW/m2. The Voc watermelon substrate has a maximum of 451 mV, maximum current density of 306 mA/m2 and maximum power density of 18.6 mW/m2. Voc mango substrate has a maximum of 586 mV, maximum current density of 229 mA/m2 and maximum power density of 4.3 mW/m2. Voc papaya substrate is a maximum of 338 mV, maximum current density of 58 mA/m2 and maximum power density of 2.9 mW/m2. These results show the potential for renewable electricity sources.

Efisiensi Prototipe Turbin Savonius pada Kecepatan Angin Rendah Melda Latif
Jurnal Rekayasa Elektrika Vol 10, No 3 (2013)
Publisher : Universitas Syiah Kuala

Wind energy can be transformed into electrical energy using wind turbine. Based on rotation axis, there are two types of wind turbine, namely turbine with horizontal axis and the one with vertical axis. Turbine with vertical axis has been known with various names that are Darrieus turbine, Savonius turbine and H turbine. This research designed and implemented a prototype of simple Savonius turbine for small scale wind speed. Resistor with resistance of 200 ohm and LED are used as the load. Material of the prototype is alumunium plate, which is light and easy to find. The experiment was conducted at the beach. Permanent magnet synchronous generator was chosen for generating equipment. Voltage resulted by the generator increased as the wind speed increased. The prototype began rotating at wind speed 2.4 m/s. Average efficiency for Y and D connected load are 4.8% and 14.5% respectively.

Perancangan Sistem Smart Egg Incubator sebagai Optimalisasi Pemanfaatan Energi Terbarukan di Ngalau Baribuik, Padang Refdinal Nazir; Andi Pawawoi; Melda Latif; Muhammad Imran Hamid; Pinto Anugrah; Eka Fitrianto
Warta Pengabdian Andalas Vol 30 No 2 (2023)
Publisher : Lembaga Penelitian dan Pengabdian kepada Masyarakat (LPPM) Universitas Andalas

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.25077/jwa.30.2.304-313.2023

Micro Hydro (PLTMH) Ngalau Baribuik, Padang - West Sumatra, has operated since 2012. It is currently the only source of electricity for the local community, some of whom work as chicken breeders. Based on community service activities in 2021, information was obtained that the PLTMH's electricity had yet to be utilized optimally. Meanwhile, chicken breeders also needed egg incubators to increase their productivity. This community service activity aims to design an IoT-based automatic egg incubator to optimize the use of renewable energy. Activities started with field visits, making initial plans, designing and testing the machine, handing over the machine, and disseminating knowledge. The designed a smart egg incubator worked well after a 21-day hatching test for chicken eggs. The IoT technology installed on the device also functions appropriately and can show real-time temperature and humidity on mobile devices.

The Study of Plant Microbial Fuel Cell for Alternative Energy Source Melda Latif; Paskalina Aprila Tiy; Mumuh Muharam; Aulia; Amirul Luthfi
JURNAL NASIONAL TEKNIK ELEKTRO Vol 12, No 2: July 2023
Publisher : Jurusan Teknik Elektro Universitas Andalas

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.25077/jnte.v12n2.1061.2023

Plant Microbial Fuel Cell (P-MFC) is one of Microbial Fuel Cell type. It can produce electricity and source for plant living. By using the humus soil in the anode chamber, the electron can flow to the cathode chamber. The principle of Plant Microbial Fuel Cell is same with the battery. It flows the direct current. This research makes dual chamber of P-MFC prototype. The salt bridge is used as connection between anode chamber to cathode chamber. The humus soil comes from burning organic waste. Its color is black and contains a lot of microbes. The plant selected in this research was Water Spinach. The number of water spinach were 20 and 25 stems. P-MFC which has more Water Spinach will produce more voltage and current than the others. For 25 Water Spinach, P-MFC produced 762.4 mV no-load average voltage and 125.8 mV, 085 mA for load condition. The result was bigger caused by for more plants will be more microbes resulted in the humus soil.

Efisiensi Prototipe Turbin Savonius pada Kecepatan Angin Rendah Melda Latif
Jurnal Rekayasa Elektrika Vol 10, No 3 (2013)
Publisher : Universitas Syiah Kuala

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17529/jre.v10i3.1030

Wind energy can be transformed into electrical energy using wind turbine. Based on rotation axis, there are two types of wind turbine, namely turbine with horizontal axis and the one with vertical axis. Turbine with vertical axis has been known with various names that are Darrieus turbine, Savonius turbine and H turbine. This research designed and implemented a prototype of simple Savonius turbine for small scale wind speed. Resistor with resistance of 200 ohm and LED are used as the load. Material of the prototype is alumunium plate, which is light and easy to find. The experiment was conducted at the beach. Permanent magnet synchronous generator was chosen for generating equipment. Voltage resulted by the generator increased as the wind speed increased. The prototype began rotating at wind speed 2.4 m/s. Average efficiency for Y and D connected load are 4.8% and 14.5% respectively.

Penerapan Sampah Buah Tropis untuk Microbial Fuel Cell Melda Latif; Arif Dwi Fajri; Mumuh Muharam
Jurnal Rekayasa Elektrika Vol 16, No 1 (2020)
Publisher : Universitas Syiah Kuala

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17529/jre.v16i1.15723

Microbial Fuel Cell (MFC) is one tool that uses microbes to produce electrical energy. The main components of MFC support are anodes, cathodes, and salt bridges. In this paper, the application of tropical fruit waste to MFC is presented. Tropical fruit waste used here are pineapples, oranges, bananas, watermelons, mangos, and papayas. The fruit waste is extracted and fermented to produce microbial. The microbial produces ions attached to the anode. Measurement of system current and voltage is carried out using a digital multimeter. In pineapple substrate MFC, Voc has a maximum of 485 mV, maximum current density is 163 mA/m2 and maximum power density of 11mW/m2. The orange substrate obtained Voc maximum of 805 mV, maximum current density of 661 mA/m2 and maximumpower density of 62 mW/m2. Voc banana substrate has a maximum of 312 mV, maximum current density of 118 mA/m2 and maximum power density of 5.9 mW/m2. The Voc watermelon substrate has a maximum of 451 mV, maximum current density of 306 mA/m2 and maximum power density of 18.6 mW/m2. Voc mango substrate has a maximum of 586 mV, maximum current density of 229 mA/m2 and maximum power density of 4.3 mW/m2. Voc papaya substrate is a maximum of 338 mV, maximum current density of 58 mA/m2 and maximum power density of 2.9 mW/m2. These results show the potential for renewable electricity sources.

Potensi Energi Listrik Pada Gas Buang Sepeda Motor Melda Latif; Nuri Hayati; Uyung Gatot S Dinata
Jurnal Rekayasa Elektrika Vol 11, No 5 (2015)
Publisher : Universitas Syiah Kuala

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.17529/jre.v11i5.2957

The fossil energy sources dwindling due to the many needs, especially in industrial and automotive sectors which are the largest energy users and the highest waste heat-producing. This causes many alternative energy sources are developing, included thermal energy utilization. The research utilized waste heat energy from motorcycle exhaust pipe into electrical energy with using Thermo Electric Generator (TEG). By using the thermocouple principle, difference of temperature between hot and cold side of TEG resulted voltage. Testing was conducted with three points are on head, body and mouth of the exhaust pipe. The maximum output voltage is generated in the head is greater than the other positions. At the head of exhaust, the maximum output voltage which is generated by 1 modul, 2 modules and 3 modules of TEG on each other is 1.26 V, 2.27 V and 3.43 V respectively.

Analysis of Exhaust Gas Heat Utilization in Waste Heat Recovery Power Generator at Indarung V Factory PT Semen Padang Mayang Safira; Melda Latif; Zaini Zaini; Aulia Aulia; Mumuh Muharam; Waweru Njeri
Andalas Journal of Electrical and Electronic Engineering Technology Vol. 3 No. 1 (2023): May 2023
Publisher : Electrical Engineering Dept, Engineering Faculty, Universitas Andalas

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.25077/ajeeet.v3i1.34

Increasing energy efficiency in the cement production process at PT Semen Padang is carried out by reusing exhaust gas to produce electricity using Waste heat recovery power generation (WHRPG) with a capacity of 8.5 MW. WHRPG is a technology for utilizing exhaust gas heat as a source of heat energy to heat feed water into steam by using a suspension preheater (SP) boiler and air quenching cooler (AQC) boiler. This study aims to calculate the power potential of the steam heat influenced by the steam temperature and the mass flow rate of the steam produced by the boiler, to calculate the efficiency of the boiler using the direct method by comparing the boiler output heat against the boiler input heat, to calculate the turbine efficiency based on the difference between the steam enthalpy enter the turbine against the steam enthalpy out of the turbine and the isotropic enthalpy of the steam out of the turbine and to calculate the power generated by WHRPG at PT Semen Padang. The results obtained in this study are the total potential power of steam heat is 19.778 MW, the boiler AQC efficiency is 70.30%, the boiler SP efficiency is 94.04% and the turbine efficiency is 78.64%. The electricity generated by PT Semen Padang's WHRPG is 3.70 MW.

Title

Found 30 Documents
Search

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Title Search

Found 30 Documents Search

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Abstract

Title

Found 30 Documents
Search