Claim Missing Document
Check
Articles

Found 31 Documents
Search

Pengaruh Partikel Nanosilika Terhadap Sifat Tolak Air Bahan Isolasi Bionanokomposit Aulia, Aulia; Alfajri, Roan; Waldi, Eka Putra; Novizon, Novizon
JURNAL NASIONAL TEKNIK ELEKTRO Vol 9, No 2: July 2020
Publisher : Jurusan Teknik Elektro Universitas Andalas

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.25077/jnte.v9n2.716.2020

Abstract

The nature of hydropobicity plays an important role of an insulator, especially the outdoor insolator which is always exposed to hot, cold, humid weather and rain water. In the long run, the surface of the insulator can be damaged and its hydropobicity properties will be reduced or even lost so that surface discharge events will be easier to occur, especially in the rainy season. As a new material being developed, bionanocomposite insulation materials from LDPE, natural rubber and nanosilica fillers have passed several dielectric properties such as partial discharge characteristics under normal conditions and at higher temperature conditions. To complete the assessment of dielectric properties, a new bionanocomposite material hydropobicity was tested. There were 4 types of samples tested with the weight of the nanosilica material 1.5%, 3.0%, 4.5% and 6% of the total weight of the biocomposite sample. The test was carried out using a high-resolution camera to take pictures of the surface of the insulator sample that was dripped with water. The results show that nanosilica can increase the angle of contact of water with the bionanocomposite surface. This increase indicates an increase in the hydropobicity of bionanocomposite materialKeywords : LDPE, Karet Alam, Natural Rubber, nanosilica, hydrophobisity AbstrakSifat hidropobisitas memainkan peran penting dari sebuah isolator, terutama isolator pasang luar yang selalu terpapar oleh perubahan cuaca panas, dingin, lembab dan air hujan. Dalam jangka panjang, permukaan isolator bisa rusak dan sifat hidropobisitasnya akan berkurang bahkan hilang sehingga peristiwa peluahan permukaan akan lebih mudah terjadi, terutama pada musim hujan. Sebagai material baru yang sedang dikembangkan, bahan isolasi bionanokomposit dari polietilena berkerapatan rendah (LDPE), karet alam (NR) dan pengisi nanosilika telah melewati beberapa pengujian sifat dielektrik seperti karakteristik peluahan sebagian pada kondisi normal dan pada kondisi suhu yang lebih tinggi. Untuk melengkapi pengkajian sifat dielektrik, maka dilakukan pengujian sifat hidropobisitas bahan bionanokomposit yang baru tersebut. Sampel yang diuji ada 4 jenis dengan kada berat bahan nanosilika 1,5%, 3,0%, 4,5% dan 6% dari berat total sampel biokomposit. Pengujian dilakukan dengan menggunakan kamera beresolusi tinggi untuk mengambil gambar permukaan sampel isolator yang ditetesi air. Hasil menunjukan bahwa nanosilika dapat memperbesar sudut kontak air dengan permukaan bionanokomposit. Peningkatan ini mengindikasikan meningkatnya sifat hidropobisitas material bionanokomposit.Kata Kunci : Biokomposit, Hidropobisitas, Karet Alam, LDPE
Analisis Citra Permukaan Isolasi Listrik Dari Bahan LDPE-NR Akibat Aktifitas Peluahan Sebagian Darwison, Darwison; Aulia, Aulia
JURNAL NASIONAL TEKNIK ELEKTRO Vol 6, No 1: Maret 2017
Publisher : Jurusan Teknik Elektro Universitas Andalas

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.25077/jnte.v6n1.369.2017

Abstract

The correlation between the partial discharge (PD) pulses count and the surface of the related sample was studied and reported in this paper. The assessment was done by testing different samples of the composite low density polyethylene (LDPE) and natural rubber (NR) under a high electric field for 60 minutes. The results showed a strong correlation between the images of the sample surface after testing by the number of PD pulses is counted. The high of PD pulses counted are highly correlated with the larger scale of surface area damaged.Keywords : partial discharge, composite, polyethilene, natural rubber, surface pictureAbstrak— Korelasi antara jumlah pulsa peluahan sebagian (PD) dengan tingkat kerusakan permukaan sampel dikaji dalam makalah ini. Pengkajian dilakukan dengan menguji sampel berbeda dari komposit polietilen berkerapatan rendah (LDPE) dan karet alam (NR) di bawah pengaruh medan listrik tinggi selama 60 menit. Hasil memperlihatkan adanya korelasi yang kuat antara citra permukaan sampel setelah pengujian dengan jumlah pulsa PD yang terhitung. Jumlah pulsa PD yang tinggi berkorelasi dengan luas citra pemukaan sampel rusak yang lebih besar.Kata Kunci : peluahan sebagian, komposit, polietilen, karet alam, citra permukaan
Pengaruh Penuaan Elektrik Terhadap Karakteristik Tegangan Tembus dan PDIV Minyak NanoNynas Aulia, Aulia; Manab, Abdul; Putra Waldi, Eka; Kodrat, Muhammad; Widia, Gusvita
JURNAL NASIONAL TEKNIK ELEKTRO Vol 7, No 1: March 2018
Publisher : Jurusan Teknik Elektro Universitas Andalas

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (202.538 KB) | DOI: 10.25077/jnte.v7n1.522.2018

Abstract

The dielectric strength of pure nynas oil can be enhanced by adding various nanoparticles such as nanoalumina (Al2O3). To see the effect of the addition of alumina nanoparticles, 4 types of nynas oil have been prepared with the addition of nanoalumina particles by 0.00%, 0.010%, 0.015% and 0.020%. All samples were tested for dielectric breakdown voltage and partial discharge inception voltage (PDIV) test at room temperature with reference to IEC 60156 test standards. The results showed that the nanonynas oil breakdown voltage increased by 6% and the value of the partial discharge inception voltage also higher than that of pure oil. Keywords : Mineral oil, alumina, brekadown voltage, partial discharge inception voltageAbstrakKekuatan dielektrik minyak transformator nynas nitro murni dapat ditingkatkan dengan menambahkan berbagai partikel nano seperti nanoalumina (Al2O3).Penelitian ini bertujuan untuk melihat effek penambahan partikel nano alumina terhadap karakteristik tegangan tembus dan tegangan insepsi peluahan sebagian. Empat jenis minyak nynas dengan komposisi penambahan partikel nanoalumina sebesar 0.00%, 0.010%, 0.015% dan 0.020% diuji tegangan tembus dielektrik, tegangan insepsi peluahan sebagian (PDIV) pada suhu ruang dengan merujuk kepada standar pengujian IEC 60156. Hasil menunjukkan bahwa tegangan tembus minyak nanonynas meningkat sebesar 6% dan nilai tegangan insepsi dan peluahan sebagian lebih tinggi dibandingkan dengan minyak murni. Kata Kunci : Minyak  nynas nitro libra, alumina (AL2O3), tegangan tembus, PDIV
Pembangkit Listrik Pikotermal Matahari, Kajian Awal Aulia, Aulia; Darwison, Darwison; Razak, Faisyal; Waldi, Eka Putra
JURNAL NASIONAL TEKNIK ELEKTRO Vol 6, No 1: Maret 2017
Publisher : Jurusan Teknik Elektro Universitas Andalas

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (246.519 KB) | DOI: 10.25077/jnte.v6n1.368.2017

Abstract

A Picothermal solar power plant (PLTPM) is an original concept that is still under study. Testing and calculation of voltage and electrical current is carried on a single thermoelectric, thermoelectric cells connected in series and parallel connected thermoelectric cells due to rise in temperature in the cells. The results showed that the increase in temperature of 71 °C produces 1 volt output voltage and current of 0.1 amperes. In accordance with the principle of series and parallel connection, series connection is able to multiply the output voltage and the parallel connections double the current output for one additional thermoelectric cell chipKeywords : Picothermal, thermoelectric cell and series, parallel, temperatureAbstrak— Pembangkit listrik pikotermal matahari (PLTPM) merupakan konsep awal yang masih dalam tahap kajian. Pengujian dan perhitungan tegangan dan arus listrik dilakukan terhadap termoelektrik tunggal, sel termoelektrik terhubung seri dan sel termoeletrik terhubung paralel akibat kenaikan suhu pada sel-sel tersebut. Hasil memperlihatkan bahwa kenaikan suhu sebesar 71 oC  menghasilkan tegangan keluaran 1 volt dan arus 0.1 Amper. Sesuai dengan kaedah hubungan seri dan paralel, hubungan seri mampu melipat gandakan tegangan keluaran dan hubungan paralel melipatkan gandakan arus keluaran untuk tambahan setiap satu keping sel termoelektrik.Kata Kunci : pikotermal, sel termoelektrik, seri, paralel, kenaikan suhu
Prediction of ZnO Surge Arrester Degradation Based on Temperature and Leakage Current Properties Novizon, Novizon; Abdul-Malek, Zulkarnain; Aulia, Aulia; Waldi, Eka Putra; Rajab, Abdul; Darwison, Darwison
JURNAL NASIONAL TEKNIK ELEKTRO Vol 7, No 2: July 2018
Publisher : Jurusan Teknik Elektro Universitas Andalas

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (435.089 KB) | DOI: 10.25077/jnte.v7n2.501.2018

Abstract

Temperature and leakage current on the ZnO arrester are interrelated with each other. In low conduction region, voltage-current characteristics of ZnO surge arrester are highly dependent on temperature. The leakage current will increase as the temperature increases and experience thermal runaway when the temperature exceeds the acceptable limit. This phenomenon is associated with the increase of resistive leakage current due to degradation. Therefore the temperature and leakage current are good indicator to evaluate the condition of ZnO arrester. This paper proposed the degradation  prediction of ZnO surge arrester by analyzed the temperature and leakage current. The 132 kV station type ZnO surge arrester was employed. Temperature profile of ZnO arrester was obtained using thermal camera. The leakage current was measured simultaneous with the temperature measurement to attain the leakage current at the actual temperature. The results shows the leakage current continue increasing by increasing the temperature. Keywords : Resistive leakage current, temperature, degradation, prediction, zinc oxide surge arrester
Clarification of the optimum silica nanofiller amount for electrical treeing resistance Z. Nawawi; M. A. B. Sidik; M. I. Jambak; C. L. G. Pavan Kumar; Aulia Aulia; M. H. Ahmad; A. A. Abd Jamil
TELKOMNIKA (Telecommunication Computing Electronics and Control) Vol 17, No 6: December 2019
Publisher : Universitas Ahmad Dahlan

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.12928/telkomnika.v17i6.10605

Abstract

This paper aims to clarify the optimum amount of fumed silica (SiO2) nanofiller in resisting the initiation and propagation of electrical treeing in silicone rubber (SiR). Unlike other works, SiR/SiO2 nanocomposites containing seven different weight percentages of SiO2 nanofiller were prepared for this purpose. To achieve the objective, the electrical tree characteristics of the SiR/SiO2 nanocomposites were investigated by comparing the tree initiation voltage, tree breakdown time, tree propagation length and tree growth rate with its equivalent unfilled SiR. Moreover, the structural and morphological analyses were conducted on the SiR/SiO2 nanocomposite samples. The results showed that the SiR, when added with an appropriate amount of SiO2 nanofiller, could result in an improved electrical tree resistance. It implies that the 5 wt% of silica is the optimum amount to achieve the optimal electrical tree resistance such that above 5 wt%, the tree resistance performance has been abruptly reduced, subjected to the agglomeration issue.
The effect of silica content to partial discharge characteristic of low-density polyethene and natural rubber blend as the electrical insulator Aulia Aulia; Eka Putra Waldi; Darwison Darwison; Dwi Gustiono; Novizon Novizon; M. Heru Setiawan; M. A. Hafizi
TELKOMNIKA (Telecommunication Computing Electronics and Control) Vol 19, No 2: April 2021
Publisher : Universitas Ahmad Dahlan

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.12928/telkomnika.v19i2.16417

Abstract

The dielectric properties of low-density polyethylene natural rubber (LDPE-NR) biopolymeric insulating materials can be improved by adding the silica nanoparticles in a certain percentage of weight (w%). In the present study, four types of bio-nano polymeric samples were prepared. To each sample, the nanosilica particles with wt% 1.5%, 3%, 4.5% and 6%. As one characteristic of dielectric, the partial discharge (PD) characteristics, each sample has been tested for 1 hour under AC high voltage field, and the pulses were counted for each sample and grouped into positive and negative pulses. The PD pattern was also plotted based on X-Y axes, namely Φ-q-n pattern. It was found that the number of positive and negative partial discharge (PD) pulses for each silica sample after 60 minutes of testing varied for all samples. It is also found that samples with a higher percentage of nanosilica had fewer PD pulses. The PD pattern in lower w% of silica was identified in the 90 degrees mostly in containing This indicates that w% of nanosilica particles can improve the PD resistance or the insulation quality of LDPE-NR insulation materials.
The Correlation of Statistical Image and Partial Discharge Pulse Count of LDPE-NR Composite Aulia Aulia; Zulkarnain Abdul Malek; Yanuar Zulardiansyah Arief; Eka Putra Waldi
TELKOMNIKA (Telecommunication Computing Electronics and Control) Vol 15, No 3: September 2017
Publisher : Universitas Ahmad Dahlan

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.12928/telkomnika.v15i3.5149

Abstract

High voltage insulation must be designed in such a way that it is very resistant to ageing including that from partial discharge (PD). Many studies were previously carried out on composites based on low density polyethylene (LDPE). However, the use of natural rubber (NR) and nanosilica (SiO2) in the LDPE-NR based composites is relatively new. Furthermore, the PD resistant performance of the composites is yet to be extensively researched. This work aims to analyze the correlation between PD pulse count and its related image to interpreting the effect of PD signals. The results show there is a strong correlation between PD pulse count and the statistical image. The results indicate that the surface image statistical analysis can be used as a tool to justify the total of the PD pulse count on the surface for different samples of composite.
An optimized method of partial discharge data retrieval technique for phase resolved pattern Eka Putra Waldi; Aulia Aulia; Ariadi Hazmi; Hairul Abral; Syukri Arief; Mohd Hafizi Ahmad
TELKOMNIKA (Telecommunication Computing Electronics and Control) Vol 14, No 1: March 2016
Publisher : Universitas Ahmad Dahlan

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.12928/telkomnika.v14i1.2602

Abstract

The measurement of phase resolved partial discharge requires a gigantic memory capacity to store all the waves of the PD test results. This limitation eventually hinders the testing. It is necessary to optimize on the aspect of memory storage capability to reduce the storage requirements. In light of foregoing, the partial discharge data retrieval techniques with sampling rate methods were used to detect the peak of partial discharge as well as the PD constituent representatives. The optimization process was performed by using integration of oscilloscope and LabVIEW software. The partial discharge data recording can be easily confined to the points of the partial discharge occurrence only. As results, the storage points were reduced by taking wave magnitude associated with PD, thereby resulting in more representative data. Therefore, this optimized method was able to reduce the file size of the test results up to 97 percent of PD original size thereby decreasing the usage of hard disk storage.
Pembangkit Listrik Pikotermal Matahari, Kajian Awal Aulia Aulia; Darwison Darwison; Faisyal Razak; Eka Putra Waldi
JURNAL NASIONAL TEKNIK ELEKTRO Vol 6, No 1: Maret 2017
Publisher : Jurusan Teknik Elektro Universitas Andalas

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (246.519 KB) | DOI: 10.25077/jnte.v6n1.368.2017

Abstract

A Picothermal solar power plant (PLTPM) is an original concept that is still under study. Testing and calculation of voltage and electrical current is carried on a single thermoelectric, thermoelectric cells connected in series and parallel connected thermoelectric cells due to rise in temperature in the cells. The results showed that the increase in temperature of 71 °C produces 1 volt output voltage and current of 0.1 amperes. In accordance with the principle of series and parallel connection, series connection is able to multiply the output voltage and the parallel connections double the current output for one additional thermoelectric cell chipKeywords : Picothermal, thermoelectric cell and series, parallel, temperatureAbstrak— Pembangkit listrik pikotermal matahari (PLTPM) merupakan konsep awal yang masih dalam tahap kajian. Pengujian dan perhitungan tegangan dan arus listrik dilakukan terhadap termoelektrik tunggal, sel termoelektrik terhubung seri dan sel termoeletrik terhubung paralel akibat kenaikan suhu pada sel-sel tersebut. Hasil memperlihatkan bahwa kenaikan suhu sebesar 71 oC  menghasilkan tegangan keluaran 1 volt dan arus 0.1 Amper. Sesuai dengan kaedah hubungan seri dan paralel, hubungan seri mampu melipat gandakan tegangan keluaran dan hubungan paralel melipatkan gandakan arus keluaran untuk tambahan setiap satu keping sel termoelektrik.Kata Kunci : pikotermal, sel termoelektrik, seri, paralel, kenaikan suhu