cover
Contact Name
-
Contact Email
-
Phone
-
Journal Mail Official
-
Editorial Address
-
Location
Kota semarang,
Jawa tengah
INDONESIA
J@TI (TEKNIK INDUSTRI)
Published by Universitas Diponegoro
ISSN : -     EISSN : 25021516     DOI : -
Core Subject : Engineering,
J@ti Undip: Jurnal Teknik Industri [e-ISSN 2502-1516] merupakan jurnal nasional yang mengangkat tulisan-tulisan penelitian dalam disiplin ilmu teknik industri. Pertama kali terbit sejak tahun 2006 hingga saat ini dengan frekuensi terbit tiga (3) kali dalam setahun. Setiap edisi terbitan berisi 8 artikel jurnal. Terbit setiap Januari, Mei, dan September.
Arjuna Subject : -
Articles 465 Documents
Running-in as an Engineering Optimization Jamari, Jamari
J@ti Undip : Jurnal Teknik Industri Volume 2, No.1, Januari 2007
Publisher : Departemen Teknik Industri, Fakultas Teknik, Universitas Diponegoro

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (287.566 KB) | DOI: 10.12777/jati.2.1.1-10

Abstract

Running-in is a process which can be found in daily lives. This phenomenon occurs after the start of the contact between fresh solid surfaces, resulting in changes in the surface topography, friction and wear. Before the contacting engineering solid surfaces reach a steady-state operation situation this running-n enhances the contact performance. Running-in is very complex and is a vast problem area. A lot of variable occurs in the running-in process, physically, mechanically or chemically. These transient phenomena should be optimized so that it is beneficial. In this paper the global analysis of running-in in term of engineering optimization is presented.  Literature that reports of what have been published about knowledge and ideas, on the running-in topic by accredited scholars and researchers, are reviewed. The running-in model which can predict the real engineering surfaces in its operation is proposed. Key words: optimization, running-in, elastic-plastic contact, friction, wear,
PEMILIHAN PARAMETER PRE TREATMENT PADA PROSES PENGAWETAN BAMBU LEMINASI Nurkertamanda, Denny; Andreina, Winda; Widiani, Melinda
J@ti Undip : Jurnal Teknik Industri Volume 6, No.3, September 2011
Publisher : Departemen Teknik Industri, Fakultas Teknik, Universitas Diponegoro

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (291.072 KB) | DOI: 10.12777/jati.6.3.155-160

Abstract

Bambu merupakan salah satu sumber daya alam Non-Hutan yang banyak dimanfaatkan oleh masyarakat Indonesia. Salah satu kelemahan bahan baku bambu adalah tingkat keawetan alami yang rendah sehingga rentan terhadap organisme perusak seprti kumbang bubuk dan rayap. Pemanfaatan bahan insektisida organik daun mimba merupakan salah satu solusi untuk meningkatkan keawetan bambu sebagai bahan baku produk mebel yang ramah lingkungan. Tujuan dari penelitian ini adalah mengetahui pengaruh ekstrak daun mimba dan mendapatkan konsentrasi ekstrak yang optimal dalam pengawetan bambu. Model penelitian yang dilakukan metode Desain Eksperimen Faktorial untuk mengetahui pengaruh konsentrasi ekstrak dan lama perendaman bambu dalam proses pengawetan untuk meningkatkan keawetan bambu dari serangan organisme perusak. Daun mimba segar dicampurkan dengan air untuk menghasilkan variabel konsentrasi 100, 200, 300, 400, dan 500 gram/liter. Pada penelitian ini, bambu direndam dalam larutan konsentrasi ekstrak mimba dengan lama perendaman 30 menit dan 60 menit. Hasil penelitian menunjukkan bahwa pengurangan berat bambu yang  signifikan terjadi pada pengawetan bambu dengan konsentrasi ekstrak mimba 20% ( 200 gram/liter) selama 30 menit. Pada konsentrasi ekstrak 20%, sampel bambu mengalami pengurangan berat bambu akibat serangan rayap tanah sebesar 21,55%. Pengawetan bambu yang efektif dapat dilakukan dengan konsentrasi ekstrak mimba 30%. Kata Kunci: mebel, bambu, pengawetan, ekstrak mimba, desain eksperimen faktorial Bamboo is one of the natural resources of trees is widely used by Indonesian society. A disadvantage of raw bamboo islow level of durability, so making it vulnerable to destructive organisms such as beetles and termites powder. Utilization of organic insecticide neem leaf is one solution to improve the durability of bamboo as raw material for furniture products that are environmentally friendly. This research objective was to determine the effect of extracts of neem leaf extract and obtain the optimal concentration in the preservation of bamboo. Model used in this research is Design of Experiments Factorial to determine the effect of extract concentration and long soaking the bamboo in the process preservation to improve the durability of bamboo for the organism attack destroyer. Fresh neem leaves are mixed with water to produce variable concentrations of 100, 200, 300, 400, and 500 grams / liter. In this research, bamboo is soaked in concentration of neem extract with a long soaking 30 minutes and 60 minutes. The result of experiment showed that significant weight reduction occurred in bamboo bamboo preservation with 20% concentration of neem extract (200 grams / liter) for 30 minutes. At a concentration of extract 20% , samples of bamboo had a weight reduction as a result termite attack for 21.55%. Preservation of bamboo that can effectively be done with a 30% concentration of neem extract. Keywords: furniture, bamboo, preservation, neem extract, design of experimental factorial
ANALISA PENGARUH PENGENDALIAN KINERJA PROYEK TERHADAP MUTU PROYEK KONSTRUKSI DENGAN MENGGUNAKAN UJI STATISTIKA Rochman, Fatchur; Wahyuni, Hana Catur
J@ti Undip : Jurnal Teknik Industri Volume 12, No. 1, Januari 2017
Publisher : Departemen Teknik Industri, Fakultas Teknik, Universitas Diponegoro

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (445.065 KB) | DOI: 10.14710/jati.12.1.01-06

Abstract

Dalam proyek konstruksi perencanaan dan pengendalian merupakan fungsi yang paling pokok dalam mewujudkan keberhasilan suatu kegiatan di proyek konstruksi. Keberhasilan suatu proyek tidak lepas dengan serangkaian aktivitas yang meliputi tahapan perencanaan, pelaksanaan, dan pengawasan. Pengendalian, pengawasan serta pengukuran kinerja perlu dilakukan karena untuk mengetahui apakah dalam pelaksanaan pekerjaan terdapat penyimpangan dengan apa yang sudah ditetapkan. Maka dalam hal ini perlu dilakukan analisa untuk mengetahui indikator pengaruh pengendalian kinerja proyek (Keselamatan dan Kesehatan Kerja, Biaya, dan Waktu) terhadap Mutu proyek konstruksi menggunakan uji statistika.Hasil penelitian menunjukkan secara simultan terdapat pengaruh positif dan signifikan antara variabel Keselamatan dan Kesehatan Kerja (X1), variabel Biaya (X2), dan variabel Waktu (X3) secara simultan terhadap Mutu (Y1) ditunjukkan nilai Fhitung sebesar (25.755) lebih besar dari Ftabel (2.71) dengan tingkat signifikasi sebesar 0.000 yang lebih kecil dari sig. (α) sebesar 0.05.Untuk secara parsial variabel Keselamatan dan Kesehatan Kerja (X1) menunjukkan nilai thitung sebesar 3.672 dengan tingkat signifikasi sebesar 0.000 lebih besar dari ttabel 1.98667 dan prosentase sebesar (37%), variabel Biaya (X2) menunjukkan nilai thitung sebesar 1.705 dengan tingkat signifikasi sebesar 0.092 lebih kecil dari ttabel 1.98667 dan prosentase sebesar (17%), dan variabel Waktu (X3) menunjukkan nilai thitung sebesar 1.705 dengan tingkat signifikasi sebesar 0.334 lebih kecil dari ttabel 1.98667 dan prosentase sebesar (17%). AbstractIn the construction project planning and controlling is the most basic function in realizing the success of an activity in construction project. A success a project cannot be separated by a series of activities which is included the stages of planning, implementation and controlling. Controlling, monitoring and performance measurement needs to be done as to determine whether there are deviation in the work implementation of what has been set. Then, in this case needs to be analyzed to know the effect of controlling project performance indicators (Occupational Safety and Health, Cost and Time) toward the quality of construction project.The result of the research shows there is simultaneously a positive and significant influence between the variables of Occupational Safety and Health (X1), a Cost variable (X2) and a Time variable (X3) simultaneously toward Quality (Y1) is showed the value Fcount (25.755) is larger than Ftable (2.71) with significance level of 0.000 is smaller than sig. (α) of 0.05.For the partial variable of Occupational Safety and Health (X1) indicates tcount amounted to 3.672 with significance level amount of 0.000 is larger than ttable 1.98667 and a percentage of (37%), a cost variable (X2) indicates tcount amounted to 1.705 with significance level amount of 0.092 is smaller than ttable 1.98667 and a percentage of (17%), and a time variable (X3) is showed value of tcount amounted to 1.705 with significance level amount of 0.334 is smaller than ttable 1.98667 and a percentage amount of (17%).
USULAN SISTEM PEMESANAN UNTUK MENINGKATKAN SERVICE LEVEL PADA SISTEM HEIJUNKA Hartini, Sri; Fanani, Zainal; Rachimi A., Luki
J@ti Undip : Jurnal Teknik Industri Volume 3, No.3, September 2008
Publisher : Departemen Teknik Industri, Fakultas Teknik, Universitas Diponegoro

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (346.652 KB) | DOI: 10.12777/jati.3.3.191-202

Abstract

PT X merupakan distributor  yang melayani permintaan suku cadang untuk wilayah Jawa Tengah dan Yogyakarta. Salah satu ukuran kepuasan pelanggan adalah service level.Berdasarkan data perusahaan pada bulan Januari – April 2007, service level global untuk keseluruhan item masih berada dibawah target service level yang ditetapkan oleh perusahaan. Pada penelitian ini diberikan usulan perbaikan pada sistem peramalan dan model pemesanan untuk item kritis, yaitu item 90915-TE001 dan 85214-0A010.Untuk mengatasi fluktuasi demand, peneliti mengusulkan adanya safety stock yang ditentukan berdasarkan besarnya fluktuasi  demand dan target service level yang ingin dicapai. Dari hasil penelitian didapatkan bahwa model peramalan yang sesuai adalah Holt Exponential Smoothing untuk item 90915-TE001, dan Single Exponential Smoothing untuk item 85214-0A010. Selain itu, perhitungan safety stock dan MIP berdasarkan model usulan,  meningkatkan rata – rata aktual service level hingga 99.38% pada sistem heijunka. Kata Kunci: service level, peramalan, pemesanan heijunka     Abstract   PT X, distributor  wich serves the demand of genuine parts in central java and DIY.As a Distributor Company, PT X has two kinds of responsibilities , to customer as the supplier, to always improve the satisfication of customer. One of satisfication of customer is service level. According to company data from january to april 2007, global service level for all items still stay below the service level target which is decided by company.In this research, given correction suggestion in forecasting system and ordering model for critic items, those are item 90915-TE001 and 85214-OA010. For solving the demand fluctuation, researcher suggests for safety stock that is decided by the value of demand fluctuation and service level target will be reached.From the research, obtained that the suitable forecasting model is Holt Exponential Smoothingfor item 90915-TE001, and Single Exponential Smoothing for item 85214-OA010. Beside that, calculation of safety stock and MIP according to suggestion model, improve average actual service level until 99,38% in Heijunka System Keywords: service level, forecasting, order, heijunka
KNOWLEDGE CONVERSION PADA PROSES PERENCANAAN PROYEK DI PT. LEN RAILWAY SYSTEM UNTUK STANDARDISASI PROSES DENGAN METODE SECI Nisaa, Atikah Sayyidatu; Kurniawati, Amelia; Pratami, Devi
J@ti Undip : Jurnal Teknik Industri Volume 8, No.1, Januari 2013
Publisher : Departemen Teknik Industri, Fakultas Teknik, Universitas Diponegoro

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (489.77 KB) | DOI: 10.12777/jati.8.1.27-36

Abstract

PT LEN Railway System bergerak pada pembangunan proyek pensinyalan kereta api, namun pada proses perencanaan proyek pada perusahaan tersebut masih berupa tacit knowledge (pengalaman) pekerja yang akan hilang. Oleh karena itu, diperlukan adanya konversi knowledge pekerja yang masih berbentuk tacit knowledge menjadi knowledge yang terdokumentasikan ke dalam bentuk explicit knowledge. Penelitian ini menggunakan metode SECI (Socialization, Externalization, Combination, Internalization). Pada tahap socialization dilakukan eksplorasi data kepada pelaku proyek yang bersangkutan mengenai proses bisnis suatu aktivitas maupun tacit dan explicit knowledge dari masing-masing aktivitas. Pada tahap externalization dilakukan pendokumentasian dari hasil eksplorasi data. Pada tahap combination dilakukan pemilihan best practice dengan menggunakan beberapa tools yaitu: metode Delphi, metode AHP dan pemilihan best practice menggunakan metode factor rating. Best practice yang didapatkan akan dikombinasikan dengan proses aktivitas dari PMBOK. Pada tahap internalization dilakukan penginformasian kepada pekerja mengenai best practice yang telah didapatkan dari hasil penelitian. Best practice yang terpilih dari hasil perhitungan factor rating didapatkan sebagai berikut best practice pembuatan WBS adalah proses bisnis dari responden 2 dengan nilai sebesar 8,710, untuk penentuan jadwal proyek dari responden 2 dengan nilai sebesar 8,067, untuk penentuan biaya proyek dari responden 3 sebesar 9,554, untuk pemilihan supplier dari responden 1 sebesar 8,330, untuk pembuatan desain proyek dari responden 1 sebesar 8,368 dan untuk pengadaan barang dari responden 1 dengan nilai sebesar 8,195. Kata Kunci : knowledge conversion, knowledge management, metode SECI Abstract The economic foundation movement of industrial era into the knowledge era has involved the project PT LEN Railway System which operates in the construction of the railway signaling project. This research uses SECI method (Socialization, Externalization, Combination, Internalization). In socialization stage, data exploration is done toward workers regarding business, and tacit and explicit knowledge from each activity. The result from data exploration of converting tacit knowledge into explicit knowledge is then documented in externalization stage. In combination stage, best practice from the activity is selected by using several tools: Delphi method in determining criteria, AHP method in weighing each criteria and factor rating to rate best practice. The best practice later will be combined with activity process from PMBOK. In internalization stage, information about best practice is delivered to the employees. Best practice that selected from the result of factor rating calculation obtain following create WBS is the best practice from second respondent with score 8,710, for determine project schedule is the best practice from second respondent with score 8,067, for determine project cost is the best practice from third respondent with score 9,554, for supplier selection is the best practice from first respondent with score 8,330, for create project design is the best practice from first respondent with score 8,368 and for procurement is the best practice from first respondent with score 8,195. Keywords : knowledge conversion, knowledge management, SECI method
PERANCANGAN MODEL PEMILIHAN SUPPLIER PRODUK CETAKAN DENGAN MENGGUNAKAN GREY BASED TOPSIS (STUDI KASUS: RUMAH SAKIT ISLAM SULTAN AGUNG SEMARANG) Pujotomo, Darminto; Umaindra, Maulana Arif; Wicaksono, Purnawan Adi
J@ti Undip : Jurnal Teknik Industri Volume 13, No. 2, Mei 2018
Publisher : Departemen Teknik Industri, Fakultas Teknik, Universitas Diponegoro

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (729.413 KB) | DOI: 10.14710/jati.13.2.99-108

Abstract

Abstrak Pemilihan supplier merupakan aktivitas penting dari perusahaan dalam menentukan strategi yang tepat, khususnya pada bagian pengadaan. Rumah Sakit Islam Sultan Agung Semarang (RSIS) merupakan salah satu rumah sakit yang mempunyai masalah dalam melakukan pemilihan supplier produk cetakan. Masalah yang dihadapi yaitu keterlambatan barang, kesalahan mencetak produk, tidak sesuainya kuantitas barang pesan dan kualitas yang buruk yang dikirim oleh beberapa supplier, itu mengakibatkan penurunan kinerja rumah sakit, karena proses kerja akan terganggu. Harga merupakan kriteria utama yang digunakan RSIS dalam memilih supplier produk cetakan. Produk cetakan digunakan untuk menjalankan proses kerja setiap hari di rumah sakit. Tujuan dari penelitian ini adalah untuk merancang model pemilihan dan pengevaluasi supplier multi attribute dengan menggunakan metode Grey (Pemilihan) based TOPSIS (Evaluasi). Kriteria didapatkan berdasarkan wawancara dan studi literatur oleh peneliti dengan para decision maker bagian pengadaan. Terdapat tiga kriteria pemilihan supplier di RSIS dengan menggunakan metode Grey based TOPSIS, yaitu cost, quality dan service. Hasil penelitian mendapatkan supplier terbaik berdasarkan pemilihan para decision maker dengan, urutan supplier terbaik sampai terburuk yaitu supplier D dengan nilai kriteria yang paling baik, kemudian supplier E, A, C hingga supplier terburuk yaitu supplier B. Berdasarkan hasil tersebut dan wawancara didapatkan kemiripan dengan kondisi nyata dari supplier, oleh karena itu model yang dibuat dapat digunakan untuk memilih dan mengevaluasi supplier cetakan di RSIS. AbstractDESIGN OF SUPPLIER MOLD PRODUCTS SELECTION MODEL USING GREY BASED TOPSIS (CASE STUDY: RUMAH SAKIT SULTAN AGUNG SEMARANG). Supplier selection is an important activity of the company in determining the right strategy, especially on the part of procurement. Rumah Sakit Islam Sultan Agung Semarang (RSIS) is one of the hospitals that has problems in choosing a supplier of mold products. Problems encountered are product delays, product print errors, inappropriate quantity of message items and poor quality delivered by some suppliers, resulting in a decrease in hospital performance, as the work process will be disrupted. Price is the main criteria used by RSIS in choosing a supplier of printed products. Mold products are used to run the work process every day at the hospital. The purpose of this research is to design the model of selecting and evaluating the supplier of multi attribute by using the Grey method (Selection) based on TOPSIS (Evaluation). Criteria obtained based on interviews and literature studies by researchers with the decision maker procurement department. There are three criteria of supplier selection in RSIS by using Grey based TOPSIS method, that is cost, quality and service. The result of this research is finding the best supplier based on the selection of the decision maker with the best supplier to the worst that is supplier D with the best criterion value, then supplier E, A, C to the worst supplier that is supplier B. Based on the result and the interview got similarity with the condition real from the supplier, therefore the model can be used to select and evaluate the mold supplier in RSIS.Keywords: Supplier selection; RSIS; Grey; TOPSIS; Mold products
ANALISIS TINGKAT KEPENTINGAN ATRIBUT PERPUSTAKAAN BERBASIS RISET MELALUI METODE CONJOINT ANALYSIS STUDI KASUS DI UNIVERSITAS DIPONEGORO Sari, Diana Puspita; Prastawa, Heru; Lintang, Dyah
J@ti Undip : Jurnal Teknik Industri Volume 5, No.2, Mei 2010
Publisher : Departemen Teknik Industri, Fakultas Teknik, Universitas Diponegoro

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (558.757 KB) | DOI: 10.12777/jati.5.2.105-118

Abstract

Setiap Perguruan Tinggi mempunyai tugas untuk menjalankan Tridharma Perguruan Tinggi, yaitu mendukung kegiatan pendidikan atau pengajaran, pengabdian masyarakat dan penelitian. Kegiatan penelitian dan perpustakaan memiliki hubungan yang saling terkait. One can not complete his research work without the help of library. Di satu sisi kegiatan penelitian tidak akan terselesaikan tanpa bantuan perpustakaan dan sisi lain tidak dimungkinkan pula dihasilkan suatu penelitian yang baik tanpa sebuah perpustakaan. Maka konsekuensi logis dari perubahan status Universitas Diponegoro menjadi Research University akan menuntut perpustakaan Universitas Diponegoro  untuk mengakselerasi dirinya dari tahap gudang buku ke tahap pendidikan dan penelitian. Dalam penelitian ini, metode yang digunakan adalah metode Analisis Konjoin. Tujuan  dari penelitian ini adalah memberikan suatu konsep rekomendasi dalam membangun perpustakaan riset yang dibangun dengan pusat kajian detail fenomena tertentu dengan prioritas pada pengembangan wilayah pesisir dan laut tropis. Hasil dari penelitian ini adalah utility function untuk tiap-tiap taraf atribut. Karakteristik atribut yang terpilih berdasarkan pada identifikasi preferensi stakeholder adalah perpustakaan riset yang dibangun dengan standar khusus jenis riset fundamental, dengan permasalahan bidang kajian lingkungan hidup, sumber informasi yang diprioritaskan berasal dari jurnal, koleksi yang diprioritaskan pada disiplin ilmu oseanografi, adanya kebijakan alokasi hibah dana untuk meningkatkan hasil kegiatan penelitian, jejaring informasi yang berformat digital library silang layan, sistem pelayanan perpustakaan yang closed access dan sumber daya manusia yang ahli teknologi informasi. Kata Kunci : Universitas Diponegoro, perpustakaan riset, analisis konjoin.     Every colleges had assignment to enforce Threedharma, they are support of education and instruction, serving the community and research at all levels. Research and library are inter related. One can not complete his research work without the help of library and no good research is possible without a library. So, the logical from the Diponegoro University status changes to be a research university will be trundle Diponegoro University library’s to regenerate it from store house period to educational and research period. The methods used in this research is Conjoint Analysis. Steerage  from applied this method is give a rough copy recommendation to created a research library, it is special library generally treat only one subject matter is coastal area and tropical newcastles expansion. The results from this research is utility function for each an item of all. For an item have the best of identifying stakeholders’ preferences are the research library would have been created with special criterion research kind fundamental, with the investigates life surroundings, the predominant information resources from journal, the predominant branch of science church collection oceanography, there are the donation grant to increase research results, the information networking with the form digital library service crosswise, service system closed access and human resources good at information technology. Keywords : Diponegoro University, research library, conjoint analysis.
PENGGUNAAN FMEA DALAM MENGIDENTIFIKASI RESIKO KEGAGALAN PROSES PRODUKSI SARUNG ATM (ALAT TENUN MESIN) (STUDI KASUS PT. ASAPUTEX JAYA TEGAL) Puspitasari, Nia Budi; Martanto, Arif
J@ti Undip : Jurnal Teknik Industri Volume 9, No.2, Mei 2014
Publisher : Departemen Teknik Industri, Fakultas Teknik, Universitas Diponegoro

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (64.742 KB) | DOI: 10.12777/jati.9.2.93-98

Abstract

Pengendalian kualitas merupakan salah satu hal yang penting untuk mempertahankan reputasi perusahaan di mata konsumen. PT. Asaputex Jaya adalah perusahaan textil yang bergerak dalam bidang sarung tenun.  Pada saat ini cacat produk yang terjadi pada perusahaan masih ada yang diluar dari ketentuan batas perusahaan yaitu diatas angka persentase yang telah ditetapkan oleh perusahaan yaitu sebesar 2%. Sehingga perusahaan segera melakukan perbaikan agar tidak terjadi waste yang merugikan perusahaan. Dengan adanya pengendalian kualitas secara baik dan benar, maka akan diperoleh produk yang dapat memenuhi keinginan konsumen. Salah satu tool yang digunakan untuk membantu pengendalian kualitas adalah menggunakan metode Failure Modes and Effects Analysis (FMEA). Penggunaan FMEA mampu mengidentifikasi resiko kegagalan yang terjadi selama proses produksi pada pembuatan sarung tenun. Tujuan penelitian ini adalah menganalisa moda kegagalan yang menyebabkan cacat produk dengan menggunakan metode FMEA, mendapatkan resiko kegagalan proses produksi terbesar dalam nilai RPN (Risk Priority Number), memberikan usulan perbaikan untuk produksi selanjutnya.  Berdasarkan pengolahan dengan metode FMEA dapat mengidentifikasi moda kegagalan yang terjadi pada proses pembuatan sarung tenun. Moda kegagalan potensial pada proses pembuatan sarung tenun dengan alat tenun mesin (ATM) pada PT. Asaputex Jaya terdiri dari 14 jenis kegagalan. Kata Kunci : kualitas; alat tenun mesin; failure mode and effect analysis; risk priority number Abstract Quality control is one of the things that are important to maintain the company's reputation in the eyes of consumers. PT. Asaputex Jaya is a company engaged in the field of textile woven sarongs. At this time the product defect that occurs in companies that still exist outside the corporate limits of the provisions of the above percentage figures set by the company which is 2%. So the company immediately repairs to prevent harmful waste. With the quality control is good and true, it will obtain the products that can meet customer demand. One of the tools used to help control quality is to use the method of Failure Modes and Effects Analysis (FMEA). The use of FMEA is able to identify the risk of failure that occurs during the production process in the manufacture of woven sarongs. The purpose of this study was to analyze the failure modes that cause defective product using the FMEA method, get the biggest risk of failure of the production process in the value of the RPN (Risk Priority Number), and provide suggestions for improvement to the next production. Based on the processing of the FMEA method can identify failure modes that occur in the process of making woven sarongs. Potential failure modes in the process of making sarong with alat tenun mesin (ATM) at PT. Asaputex Jaya consist of 14 types of failures. Keywords: quality; alat tenun mesin; failure mode and effect analysis; risk priority number
OPTIMALISASI PENGGUNAAN RUANG KELAS PLARIND BOULEVARD DENGAN PENDEKATAN PROGRAMA LINIER Handayani, Naniek Utami; Fatimah, Laila Isnaina
J@ti Undip: Jurnal Teknik Industri Volume 1, No.1, Januari 2006
Publisher : Departemen Teknik Industri, Fakultas Teknik, Universitas Diponegoro

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (334.287 KB) | DOI: 10.12777/jati.1.1.34-41

Abstract

Peningkatan jumlah mahasiswa dari tahun ke tahun di Program Studi Teknik Industri merupakan hal yang tidak dapat dihindari. Di lain pihak, ruang kuliah yang tersedia masih sangat terbatas sehingga tidak dapat mengimbangi peningkatan jumlah mahasiswa. Salah satu faktor yang mempengaruhi keterbatasan ini adalah ketersediaan gedung perkuliahan dimana hal tersebut sangat tergantung pada proses pembangunan infrastruktur yang ada di Universitas Diponegoro secara keseluruhan. Guna mengatasi permasalahan tersebut, peneliti mengusulkan pemakaian ruang kuliah bersama di Plarind Boulevard, akronim dari Planologi-Arsitek Industri, sebagai satu solusi alternatif. Pemakaian ruang kuliah bersama di Plarind Boulevard ini akan mengakibatkan pengaturan jadwal yang semakin kompleks di ketiga jurusan yang terlibat. Untuk itu diperlukan adanya pengaturan jadwal penggunaan kelas sehingga diperoleh solusi optimal yang dapat memeratakan penggunaan ruang dengan menyesuaikan kapasitas ruang dan jumlah peserta mata kuliah yang bersangkutan.Hasil penelitian menunjukkan bahwa rescheduling yang dilakukan dengan pendekatan programa linier terhadap seluruh ruang dapat mereduksi waktu penggunaan antar ruang yang pada akhirnya dapat dimanfaatkan untuk keperluan aktifitas perkuliahan lain. Kata Kunci: Rescheduling, Plarind Boulevard, Programa Linier, Solusi Optimal
ANALISIS DESAIN TOJOK SEBAGAI ALAT SORTASI TBS KELAPA SAWIT DI LOADING RAMP Anizar, Anizar
J@ti Undip : Jurnal Teknik Industri Volume 10, No. 3, September 2015
Publisher : Departemen Teknik Industri, Fakultas Teknik, Universitas Diponegoro

Show Abstract | Download Original | Original Source | Check in Google Scholar | Full PDF (374.682 KB) | DOI: 10.12777/jati.10.3.149-154

Abstract

Proses sortasi tandan buah segar (TBS) di loading ramp dilakukan oleh operator laki-laki berupa kegiatan menurunkan TBS dari truk, mensortir TBS dan menaikkan TBS mentah ataupun busuk ke truk dengan berat TBS berkisar 20 kg hingga 25 kg dengan menggunakan tojok.  Tojok merupakan sebatang besi berujung tajam dengan pegangan berbentuk T sepanjang 85 cm, diameter batang 2,5 cm dan lebar pegangan 15 cm. Desain tojok aktual menyebabkan operator sortasi memiliki postur tubuh bungkuk,  leher  tunduk, dan lutut tertekuk secara berulang-ulang selama satu hari. Operator mengeluhkan rasa sakit pada otot (MSDs) terutama pada pinggang, lengan atas kanan, punggung, lengan bawah kanan, tangan kanan, dan betis kanan. Keluhan MSDs yang dialami operator semakin meningkat sebanding dengan jumlah truk yang harus dibongkar TBS nya dalam sehari. Metode yang digunakan adalah observasi lapangan dan wawancara dengan kuesioner terhadap operator sortasi sejumlah 8 orang. Penyebaran kuesioner terbuka untuk memperoleh atribut tojok diberikan kepada 30 orang responden. Hasil yang diperoleh adalah tojok  terbuat dari bahan stainless steel, mata tojok terbuat dari besi AS, pegangan berbentuk segitiga, pembatas batang tojok dengan mata tojok berjarak 10 cm dan pegangan  tambahan berjarak 30 cm dari handle. Panjang tojok 97,1 cm, lebar pegangan tojok 11 cm dan diameter batang tojok 2,77 cm. Kata kunci : desain; ergonomis; sortasi; tojok; TBS Abstract Design Analysis of Tojok as Sorting Tools TBS Palm Oil in Loading Ramp. TBS Sorting process in loading ramp, done by male operators,  is the act of bringing down the TBS from the truck, sorting TBS and bringing the raw or rotten TBS back into the truck and the TBS weigh around 20 kg to 25 kg using tojok. Tojok is a steel bar with a sharp end and a handle forming T-shape at the other end that. The dimension is 85 cm long, 2.5 cm in diameter, and 15 cm for handle width. The actual tojok design make the operators to bent their back, flex their kness, and bowed their head for multiple times in a day. Operators are complaining about pain in their muscles (MSDs), especialy in waist, upper arm, back, lower right arm, and right calf. The MSDs pain felt by operators increase as they discharged more TBS from the truck throughout the day. The method used in finding this information is field observation and interview with 8 operators. The result is that tojok is made of stainless steel, its sharp end is made of AS steel, its handle’s shape is triangle, the length from its sharp end to its bar border is 10 cm, and the distance from the handle to another extra handle is 30 cm. The tojok length is 97.1 cm, its handle width is 11 cm, and the diameter is 2.77 cm Keywords:  design; ergonomics; sorting; tojok; TBS

Filter by Year

2006 2026


Filter By Issues
All Issue Vol 21, No 1 (2026): Januari 2026 Vol 20, No 3 (2025): September 2025 Vol 20, No 2 (2025): Mei 2025 Vol 20, No 1 (2025): Januari 2025 Vol 19, No 3 (2024): September 2024 Vol 19, No 2 (2024): Mei 2024 Vol 19, No 1 (2024): Januari 2024 Vol 19, No 2 (2024): Article In-Press Vol 18, No 3 (2023): September 2023 Vol 18, No 2 (2023): Mei 2023 Vol 18, No 1 (2023): Januari 2023 Vol 17, No 3 (2022): September 2022 Vol 17, No 2 (2022): Mei 2022 Vol 17, No 1 (2022): Januari 2022 Vol 16, No 4 (2021): Edisi Khusus ACISE 2021 Vol 16, No 3 (2021): September 2021 Vol 16, No 2 (2021): Mei 2021 Vol 16, No 1 (2021): Januari 2021 Vol 15, No 3 (2020): September 2020 Vol 15, No 2 (2020): Mei 2020 Vol 15, No 1 (2020): Januari 2020 Vol 14, No 3 (2019): September 2019 Vol 14, No 2 (2019): Mei 2019 Vol 14, No 1 (2019): Januari 2019 Vol 13, No 3 (2018): September 2018 Volume 13, No. 2, Mei 2018 Volume 13, No. 1, Januari 2018 Volume 12, No. 3, September 2017 Volume 12, No. 2, Mei 2017 Volume 12, No. 1, Januari 2017 Volume 11, No. 3, September 2016 Volume 11, No. 2, Mei 2016 Volume 11, No. 1, Januari 2016 Volume 10, No. 3, September 2015 Volume 10, No. 2, Mei 2015 Volume 10, No. 1, Januari 2015 Volume 9, No.3, September 2014 Volume 9, No.2, Mei 2014 Volume 9, No.1, Januari 2014 Volume 8, No.3, September 2013 Volume 8, No.2, Mei 2013 Volume 8, No.1, Januari 2013 Volume 7, No.3, September 2012 Volume 7, No.2, Mei 2012 Volume 7, No.1, Januari 2012 Volume 6, No.3, September 2011 Volume 6, No.2, Mei 2011 Volume 6, No.1, Januari 2011 Volume 5, No.3, September 2010 Volume 5, No.2, Mei 2010 Volume 5, No.1, Januari 2010 Volume 4, No. 3, September 2009 Volume 4, No. 2, Mei 2009 Volume 4, No. 1, Januari 2009 Volume 3, No.3, September 2008 Volume 3, No.2, Tahun 2008 Volume 3, No.1, Januari 2008 Volume 2, No.2, Mei 2007 Volume 2, No.1, Januari 2007 Volume 1, No.3, September 2006 Volume 1, No.2, Mei 2006 Volume 1, No.1, Januari 2006 More Issue