cover
Contact Name
Syamsiar Kautsar
Contact Email
j-teta@polije.ac.id
Phone
+6281217161711
Journal Mail Official
j-teta@polije.ac.id
Editorial Address
Jurusan Teknik, Politeknik Negeri Jember Jl. Mastrip PO Box 164, Jember, Jawa Timur
Location
Kab. jember,
Jawa timur
INDONESIA
Jurnal Teknik Terapan (J-TETA)
ISSN : -     EISSN : 2829615X     DOI : https://doi.org/10.25047/jteta
Core Subject : Engineering,
JTETA : Jurnal Teknik Terapan (EISSN. 2829-615X) is a peer-reviewed journal published by Politeknik Negeri Jember. JTETA is published two times annually, in April and October. This journal provides a place for academics, researchers, and practitioners to publish scientific articles. The scope of the articles listed in this journal is related to various topics such as Civil Engineering, Electrical Engineering, Informatics Engineering, Craft Engineering, Architecture, Industrial Engineering, Mechanical Engineering, Engineering Education, and other related engineering fields.
Articles 71 Documents
The Free Fatty Acid Reduction Using Cacao (Theobroma cacao L) Bean Husk Charcoal In Used Cooking Oil Dafit Ari Prasetyo; Dicky Adi Tyagita; Cahyaning Nur Karimah; Alex Taufiqurrohman Zain; Umi Sholikah
Jurnal Teknik Terapan Vol. 5 No. 1 (2026): April
Publisher : P3M Politeknik Negeri Jember

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.25047/jteta.v5i1.126

Abstract

Used cooking oil if not well-maintained will give some problems to drainage system or surface water. Used cooking oil has the potential to be processed into energy. However, the high free fatty acid (FFA) as a result of the use of cooking oil makes the process into energy more difficult. Because the high free fatty acid content will cause the saponification reakction in making used cooking oil into energy. Cocoa bean husk charcoal (Theobroma cacao L) has a K2CO3 content that similar to its commercial product, and also contains some traces of silicates and sulfates so that it can increase the efficiency of free fatty acids removal in used cooking oil. In this study, tests were carried out to reduce FFA levels in used cooking oil using charcoal from cocoa bean husks activated with 10M of hydrochloric acid, varying the concentrations of 5, 7.5, and 10%-m/v, as well as the temperature treatment during the process of mixing used cooking oil with activated charcoal adsorbent, which was 75, 100, and 150°C. The best FFA reduction results were found in the C2T2 reactor which reached 75% of FFA removal, where the best concentration of cocoa bean husk charcoal as an adsorbent were 7.5%m/v and the temperature of the mixing process was 100°C which can remove FFA content from 2.72 to 0.64
Analisis Perbandingan Ketinggian Aktivasi, Waktu Respons, dan Stabilitas Mechanical Float Switch dan Magnetic Float Switch pada Sistem Monitoring Ketinggian Air I Gede Dharma Danu Jaya; I Komang Revo Randiva Putra; Anak Agung Bagus Putra Adiyasa; I Made Sumerta Yasa; Ida Bagus Ketut Sugirianta; I Gusti Agung Made Yoga Mahaputra; I Wayan Teresna; Anak Agung Ngurah Gde Sapteka
Jurnal Teknik Terapan Vol. 5 No. 2 (2026): Oktober
Publisher : P3M Politeknik Negeri Jember

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.25047/jteta.v5i2.114

Abstract

Water level monitoring in water tank systems plays an important role in ensuring a reliable water supply and preventing overflow or dry-run conditions. Float sensors are widely used in water tank applications due to their simple structure, low cost, and ease of implementation. This study aims to evaluate and compare the accuracy, sensitivity, and stability of different float sensor configurations applied in a water tank monitoring system. The experiments were conducted under controlled water level conditions to ensure consistent and repeatable measurements. Several float sensor configurations were tested and their performance characteristics were analyzed based on the measured activation level and data variability. The experimental results indicate that sensor design has a significant influence on measurement accuracy, sensitivity to water level changes, and operational stability. Sensors with higher sensitivity tend to provide faster response and better accuracy, while improved mechanical construction contributes to more stable and consistent measurements over repeated tests. The results also show that mechanical characteristics play an important role in reducing measurement fluctuations caused by water surface disturbances. Therefore, the selection of float sensors with high sensitivity and stable mechanical performance is essential to achieve reliable and optimal water level monitoring in water tank systems.
Pengaruh Substitusi Limbah Kaca terhadap Kuat Tekan Beton Ringan Cellular Lightweight Concrete (CLC) Alya Rahma; Rosalia Dwi Werena; Muhammad Rizky Ismail; Fikri Alami; Lenny Halim
Jurnal Teknik Terapan Vol. 5 No. 2 (2026): Oktober
Publisher : P3M Politeknik Negeri Jember

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.25047/jteta.v5i2.129

Abstract

Glass waste is a non-biodegradable material that poses environmental challenges and requires sustainable management strategies. One potential approach is its utilization as a construction material in Cellular Lightweight Concrete (CLC). This study aimed to evaluate the effect of waste glass powder as a partial replacement for sand on the compressive strength of CLC and to determine the optimum substitution level. An experimental method was employed using four substitution levels of waste glass powder, namely 0%, 10%, 20%, and 30% by weight of sand. The specimens were produced using Portland Composite Cement (PCC), sand, water, foaming agent, and waste glass powder passing a 200-mesh sieve. Compressive strength testing was conducted at 28 days using a Universal Testing Machine (UTM) in accordance with SNI 8640:2018. The results showed that the incorporation of waste glass powder significantly affected the compressive strength of CLC. The optimum compressive strength of 5.82 MPa was achieved at a 20% substitution level, satisfying the requirements of SNI 8640:2018 for Class IIA non-structural lightweight concrete blocks. The improvement in strength was attributed to the filler effect and the pozzolanic reaction of amorphous silica in the glass powder, which promoted the formation of additional calcium silicate hydrate (C-S-H) and enhanced the concrete microstructure. However, excessive replacement levels led to a reduction in compressive strength due to decreased mixture homogeneity. These findings indicate that waste glass powder has considerable potential as a sustainable alternative material for lightweight concrete production.
Studi Kinetika Degradasi Edible Film Berbasis Pati Kentang dengan Penambahan Alginat dan Kitosan Berbantu Ultrasonik pada Berbagai Kondisi pH Alehandro Sitinjak; Azafilmi Hakiim; Desi Rahmawati; Indah Cintami
Jurnal Teknik Terapan Vol. 5 No. 2 (2026): Oktober
Publisher : P3M Politeknik Negeri Jember

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.25047/jteta.v5i2.131

Abstract

The accumulation of marine plastic debris has critically driven the development of sustainable, biodegradable alternatives such as polysaccharide-based edible films, yet controlling their degradation rates under varied environmental conditions remains a significant challenge. This study evaluated the starch degradation kinetics of composite edible films formulated from potato starch blends with added alginate and chitosan processed via high-intensity ultrasonic treatments. Edible films with different polymer combinations (pure starch, binary blends, and ternary mixtures) were prepared using ultrasonic processing at 30°C for 3 minutes. The percentage of starch degradation was monitored progressively over 30 minutes in acidic (pH 4.01), neutral (pH 6.86), and alkaline (pH 9.18) buffer mediums utilizing UV-Vis spectrophotometry analysis. The results demonstrated that environmental pH and polysaccharide composition synergistically influenced the structural stability and degradation rates of the films. The ternary mixture (starch-alginate-chitosan) exhibited a profound degradation surge at the end of the 30-minute exposure, reaching cumulative percentages of 2.056% in acidic, 1,990% in neutral, and 2.061% in alkaline mediums due to electrostatic repulsion and matrix swelling. Conversely, pure potato starch films maintained the lowest degradation rates (<0.03%) across all pH levels owing to their non-ionic stability. Kinetic modeling confirmed that the ternary composite maintained a consistent fit with First-Order kinetics across all pH levels, whereas pure and binary formulations shifted between Zero-Order, First-Order and Second-Order models depending on the medium's pH. In conclusion, the kinetic model fit varied depending on the formulation and pH conditions, with the First-Order model consistently fitting the mixture formulation across all pH levels, while other formulations followed Zero-Order or Second-Order models.
Analisis dan Penentuan Prioritas Faktor Penyebab Unscheduled Breakdown pada Unit OHT CAT 777D untuk Meningkatkan MTBS Menggunakan Metode AHP Saiful Adhi Wibowo; Nuzulia Khoiriyah; Nurwidiana Nurwidiana
Jurnal Teknik Terapan Vol. 5 No. 2 (2026): Oktober
Publisher : P3M Politeknik Negeri Jember

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.25047/jteta.v5i2.135

Abstract

The reliability of heavy equipment is an important factor in supporting the productivity of mining contractor companies. PT ABC still faces the problem of low Mean Time Between Stoppages (MTBS) on CAT 777D Off-Highway Truck (OHT) units, with an average MTBS of 37.9 hours compared to the company target of 60 hours, as well as a Schedule Maintenance Ratio (SMR) of 50.2% compared to the target of 80%. This condition indicates a relatively high occurrence of unscheduled breakdowns, which may affect productivity and result in potential production losses of USD 1,653,750 per month. This study aims to identify the factors causing unscheduled breakdowns, determine the priority of causal sub-factors, and develop improvement recommendations to increase MTBS using the Analytical Hierarchy Process (AHP) method. A quantitative approach was employed using data obtained from breakdown reports, MTBS reports, preventive maintenance compliance reports, and scheduled oil sampling data. The AHP hierarchy structure was developed based on three main criteria, namely manpower, maintenance, and operations, along with their respective sub-criteria determined through literature studies. The AHP analysis results indicate the priority order of the factors and sub-factors contributing to unscheduled breakdowns based on their respective importance weights. These priorities were subsequently used as the basis for developing improvement recommendations aimed at reducing unscheduled breakdowns and increasing the MTBS of CAT 777D OHT units. The findings provide an analytical basis for the company to determine maintenance improvement priorities based on the causal factors with the highest priority.
Analisis Troubleshooting Penurunan Tegangan Baterai Menggunakan Metode Deskriptif Analitis pada Dump Truck Komatsu HD 785-7 Mohamad Zainul Hasan
Jurnal Teknik Terapan Vol. 5 No. 2 (2026): Oktober
Publisher : P3M Politeknik Negeri Jember

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.25047/jteta.v5i2.137

Abstract

The operational efficiency of the Komatsu HD 785-7 Rigid Dump Truck in mining areas is frequently disrupted by engine start failures triggered by sudden and repetitive battery power drops. This study aims to identify the root cause of this issue using a descriptive analytical method with a Root Cause Analysis (RCA) approach through field troubleshooting. Evaluated parameters include the battery State of Health (SoH), State of Charge (SoC), alternator performance, and parasitic draw. The results revealed a combination of technical faults (compounding faults), including a high parasitic current reaching 1.138 A (standard < 0.05 A) due to a minor short circuit in the radio communication circuit, additional monitoring accessories, and alternator undercharging with an output of only 24,97 V (standard 26,5 V–28,5 V). Furthermore, total damage to a single battery (B4 with SoH 0% and 0 CCA) created a load imbalance that drained the remaining healthy batteries in the 24 V series-parallel network. Negligence in fluid maintenance for the Low Maintenance (LM) batteries accelerated premature sulfation. To permanently reduce unit downtime, it is recommended to repair the accessory circuits, overhaul alternator components, and standardize the transition to Calcium Maintenance-Free (MF) batteries.
Analisis Hubungan Kadar Karbon dan Energi Charpy pada Baja ST37 setelah Karburisasi Padat dengan Arang Tempurung Kelapa dan Bakau murdani murdani; Burhan Khafid; Reinaldi Teguh Setyawan
Jurnal Teknik Terapan Vol. 5 No. 2 (2026): Oktober
Publisher : P3M Politeknik Negeri Jember

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.25047/jteta.v5i2.139

Abstract

Low-carbon ST37 steel is widely used due to its good manufacturability, while surface performance is often improved through pack carburizing. This study investigates the trade-off between carbon uptake and impact toughness of ST37 steel after pack carburizing using coconut-shell charcoal and mangrove-wood charcoal (with an untreated control and a 50:50 blend as comparators). The process was conducted at 750 °C with a 180 min heating period and a 60 min holding time, followed by water quenching (≈28 °C). The main outputs were carbon content from chemical composition testing and Charpy absorbed energy (three replicates per condition). The results indicate that carbon content increased from 0.12% (control) to 0.63% with coconut-shell charcoal, 0.22% with mangrove charcoal, and 0.30% with the 50:50 blend. However, the mean Charpy energy dropped sharply for coconut-shell charcoal to 2.24 J compared with 35.92 J for the control, whereas mangrove charcoal and the 50:50 blend maintained high Charpy energy at 35.12 J. Fracture surface observations were consistent with these trends, showing brittle fracture for coconut-shell charcoal and ductile fracture for the control, mangrove charcoal, and the blend. These findings confirm a clear trade-off: the highest carbon uptake does not necessarily ensure adequate impact toughness. Therefore, media selection should be based on a dual-metric consideration of carbon increase and Charpy toughness, depending on the intended application requirements.
Crude Palm Oil (CPO) Extraction and Esterification over Natural Zeolite: Optimization of Steaming Time, Imbibition Water, Reaction Time and Catalyst Concentration Dafit Ari Prasetyo; Siti Raudhatul Ayu Hasanah; Indah Sari Pariban Pakpahan; Yuana Susmiati; Intan Dwi Wahyu Setyo Rini; Umi Sholikah; Dety Oktavia Sulistiyono
Jurnal Teknik Terapan Vol. 5 No. 2 (2026): Oktober
Publisher : P3M Politeknik Negeri Jember

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.25047/jteta.v5i2.142

Abstract

Crude palm oil (CPO) is Indonesia's most competitive biodiesel feedstock, but small-scale lines give low yield and a free fatty acid (FFA) content far above the 2 % ceiling for alkaline transesterification. This study optimises extraction from oil palm loose fruits and esterification over acid-activated natural zeolite against two targets: maximum CPO yield and residual FFA below that ceiling. Both stages used a factorial completely randomised design, ANOVA and Duncan's test (5 %). Extraction varied steaming time (60, 90, 120 min) and imbibition water (15, 20, 25 % v/m); steaming time and the interaction were highly significant, imbibition water alone was not, and 120 min with 25 % (v/m) gave the highest yield, 16.92 %. The oil met SNI 01-2901-2006 for colour, moisture and sediment but not for FFA (9.00 %) or iodine value (45.20 g I₂/100 g). Esterification applied activated zeolite at 1, 3 and 5 % (m/v) for 60, 75 and 90 min at 60 °C; all sources of variation were highly significant, and 90 min with 3 % (m/v) removed 67.55 % of the FFA. The product met the SNI 7182:2015 limits for density (887 kg/m³), viscosity (4.33 cSt), water (0.15 %) and sediment (0.17 %). The yield target was therefore achieved and four of five product specifications satisfied, but the FFA target was approached rather than reached: 2.24 % residual FFA falls 0.24 percentage points short and needs a second esterification pass. The route nevertheless offers small mills a recoverable, non-corrosive alternative to homogeneous acid pre-treatment.
Analisis Kinerja Modified Double-Jacket Burner pada Proses Pirolisis Polipropilena terhadap Produktivitas Bahan Bakar Cair Aditya Wahyu Pratama; Faruq Avero Azhar; Bayu Rudiyanto; Audha Fitrah Aulina; Reynaldi Akbar Ali; Andik Irawan; Arif Wahyudiono
Jurnal Teknik Terapan Vol. 5 No. 2 (2026): Oktober
Publisher : P3M Politeknik Negeri Jember

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.25047/jteta.v5i2.143

Abstract

Polypropylene (PP) waste pyrolysis is a thermochemical conversion method with the potential to produce liquid fuel while reducing plastic waste. This study aimed to analyze the performance of a modified double-jacket burner in the PP pyrolysis process based on liquid fuel productivity. The experiments were conducted using 2 kg of feedstock under various temperature conditions and burner configurations. The analyzed parameters included product volume, mass, density, and fuel yield. The fuel mass was calculated by multiplying the product volume by its density, while fuel yield was determined as the ratio of the liquid product mass to the initial PP feedstock mass. The results showed that pure PP processed using the modified double-jacket burner at 400 °C produced the highest volume of 1.98 L, a fuel mass of 1.782 kg, and a fuel yield of 89.10%. Pure PP processed using the standard burner at 350 °C achieved a fuel yield of 86.40%. For the 10% PP blend, the modified double-jacket burner at 370 °C produced a fuel yield of 85.50%, whereas the 20% PP blend at 290 °C produced a fuel yield of 81.00%. These results demonstrate the potential of the modified double-jacket burner to enhance condensate productivity. However, the independent effect of the burner configuration should be further investigated under identical temperature conditions.
Prototipe Sistem Monitoring Level BBM Tangki Genset Berbasis Internet Of Things (IoT) di Bandar Udara Kuala Pembuang Ibnu Taufik; Nurhedhi Desrayanto; Iwan Koswara
Jurnal Teknik Terapan Vol. 5 No. 2 (2026): Oktober
Publisher : P3M Politeknik Negeri Jember

Show Abstract | Download Original | Original Source | Check in Google Scholar | DOI: 10.25047/jteta.v5i2.144

Abstract

Maintaining fuel availability in generator set (genset) tanks is crucial for ensuring a continuous backup power supply at Kuala Pembuang Airport. This ensures that the generator can start immediately in the event of a main power outage. Currently, fuel level checks are performed manually—a process that is time-consuming and labor-intensive—potentially leading to delays in identifying fuel status. This study aims to design a real-time fuel level monitoring prototype based on microcontroller and Internet of Things (IoT) technologies. The Research and Development (R&D) method is employed, though the implementation is limited to six stages: identifying potential and problems, data collection, product design, design validation, design revision, and finalized design. The monitoring system utilizes components such as the HC-SR04 ultrasonic sensor, ESP32, and a 16×2 LCD, with the Blynk platform serving as the medium for remote monitoring. Test results across a volume range of 0–800 mL indicate an average error of 7.19% and an accuracy rate of 92.81%. The system is capable of displaying real-time data on five Android devices and issuing notifications when the fuel level drops below the minimum threshold. Based on these results, the prototype facilitates effective, practical, rapid, and measurable monitoring of fuel levels in generator tanks. Consequently, its implementation in the field would simplify the task for technicians in monitoring fuel levels and tank filling activities.